[PATCH 6/6] arm64: dts: meson-t7-a311d2-khadas-vim4: add initial device-tree
Lucas Tanure
tanure at linux.com
Sun Jun 18 10:44:33 PDT 2023
On Sun, Jun 18, 2023 at 6:41 PM Lucas Tanure <tanure at linux.com> wrote:
>
> On Fri, Jun 16, 2023 at 1:01 AM Yixun Lan <dlan at gentoo.org> wrote:
> >
> > Hi Lucas:
> >
> > On 19:29 Thu 15 Jun , Lucas Tanure wrote:
> > > The Khadas VIM4 uses the Amlogic A311D2 SoC, based on the Amlogic T7 SoC
> > > family, on a board with the same form factor as the VIM3 models.
> > I'd like to see little bit more verbose messages here, like
> > which functionality/driver added here - cpu, gic, timer, uart?
> Ok, I add this information in the next version.
> Its adding CPU, GIC, and UART.
>
> >
> > so, it's capable of booting into a serial console?
> yes
>
> >
> > >
> > > - 8GB LPDDR4X 2016MHz
> > > - 32GB eMMC 5.1 storage
> > > - 32MB SPI flash
> > > - 10/100/1000 Base-T Ethernet
> > > - AP6275S Wireless (802.11 a/b/g/n/ac/ax, BT5.1)
> > > - HDMI 2.1 video
> > > - HDMI Input
> > > - 1x USB 2.0 + 1x USB 3.0 ports
> > > - 1x USB-C (power) with USB 2.0 OTG
> > > - 3x LED's (1x red, 1x blue, 1x white)
> > > - 3x buttons (power, function, reset)
> > > - M2 socket with PCIe, USB, ADC & I2C
> > > - 40pin GPIO Header
> > > - 1x micro SD card slot
> > >
> > > Signed-off-by: Lucas Tanure <tanure at linux.com>
> > > ---
> > > arch/arm64/boot/dts/amlogic/Makefile | 1 +
> > > .../amlogic/meson-t7-a311d2-khadas-vim4.dts | 112 ++++++++++
> > > arch/arm64/boot/dts/amlogic/meson-t7.dtsi | 202 ++++++++++++++++++
> > > 3 files changed, 315 insertions(+)
> > > create mode 100644 arch/arm64/boot/dts/amlogic/meson-t7-a311d2-khadas-vim4.dts
> > > create mode 100644 arch/arm64/boot/dts/amlogic/meson-t7.dtsi
> > >
> > > diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> > > index cd1c5b04890a..1c5846bd1ca0 100644
> > > --- a/arch/arm64/boot/dts/amlogic/Makefile
> > > +++ b/arch/arm64/boot/dts/amlogic/Makefile
> > > @@ -74,3 +74,4 @@ dtb-$(CONFIG_ARCH_MESON) += meson-sm1-odroid-hc4.dtb
> > > dtb-$(CONFIG_ARCH_MESON) += meson-sm1-sei610.dtb
> > > dtb-$(CONFIG_ARCH_MESON) += meson-sm1-x96-air-gbit.dtb
> > > dtb-$(CONFIG_ARCH_MESON) += meson-sm1-x96-air.dtb
> > > +dtb-$(CONFIG_ARCH_MESON) += meson-t7-a311d2-khadas-vim4.dtb
> > > diff --git a/arch/arm64/boot/dts/amlogic/meson-t7-a311d2-khadas-vim4.dts b/arch/arm64/boot/dts/amlogic/meson-t7-a311d2-khadas-vim4.dts
> > > new file mode 100644
> > > index 000000000000..46e175536edf
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/amlogic/meson-t7-a311d2-khadas-vim4.dts
> > > @@ -0,0 +1,112 @@
> > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > > +/*
> > > + * Copyright (c) 2022 Wesion, Inc. All rights reserved.
> > > + */
> > > +
> > > +/dts-v1/;
> > > +
> > > +#include "meson-t7.dtsi"
> > > +
> > > +/ {
> > > + model = "Khadas VIM4";
> > > +
> > > + aliases {
> > > + serial0 = &uart_A;
> > > + };
> > > +
> > > + reserved-memory {
> > > + #address-cells = <2>;
> > > + #size-cells = <2>;
> > > + ranges;
> > > +
> > > + /* 3 MiB reserved for ARM Trusted Firmware (BL31) */
> > > + secmon_reserved: secmon at 5000000 {
> > > + reg = <0x0 0x05000000 0x0 0x300000>;
> > > + no-map;
> > > + };
> > > +
> > > + /* 32 MiB reserved for ARM Trusted Firmware (BL32) */
> > > + secmon_reserved_bl32: secmon at 5300000 {
> > > + reg = <0x0 0x05300000 0x0 0x2000000>;
> > > + no-map;
> > > + };
> > > + };
> > > +
> > > + xtal: xtal-clk {
> > > + compatible = "fixed-clock";
> > > + clock-frequency = <24000000>;
> > > + clock-output-names = "xtal";
> > > + #clock-cells = <0>;
> > > + };
> > > +
> > > + vddcpu_a: regulator-vddcpu-a {
> > > + /*
> > > + * MP8756GD Regulator.
> > > + */
> > > + compatible = "pwm-regulator";
> > > +
> > > + regulator-name = "VDDCPU_A";
> > > + regulator-min-microvolt = <689000>;
> > > + regulator-max-microvolt = <1049000>;
> > > +
> > > + regulator-boot-on;
> > > + regulator-always-on;
> > > + };
> > > +
> > > + vddcpu_b: regulator-vddcpu-a {
> > > + /*
> > > + * MP8756GD Regulator.
> > > + */
> > > + compatible = "pwm-regulator";
> > > +
> > > + regulator-name = "VDDCPU_B";
> > > + regulator-min-microvolt = <689000>;
> > > + regulator-max-microvolt = <1049000>;
> > > +
> > > + regulator-boot-on;
> > > + regulator-always-on;
> > > + };
> > > +};
> > > +
> > > +&clkc{
> > > + clocks = <&xtal>;
> > > + clock-names = "xtal";
> > > + status = "okay";
> > > +};
> > > +
> > > +&uart_A {
> > > + status = "okay";
> > > +};
> > > +
> > > +&cpu0 {
> > > + cpu-supply = <&vddcpu_a>;
> > > +};
> > > +
> > > +&cpu1 {
> > > + cpu-supply = <&vddcpu_a>;
> > > +};
> > > +
> > > +&cpu2 {
> > > + cpu-supply = <&vddcpu_a>;
> > > +};
> > > +
> > > +&cpu3 {
> > > + cpu-supply = <&vddcpu_a>;
> > > +};
> > > +
> > > +&cpu100 {
> > > + cpu-supply = <&vddcpu_b>;
> > > +};
> > > +
> > > +&cpu101 {
> > > + cpu-supply = <&vddcpu_b>;
> > > +};
> > > +
> > > +&cpu102 {
> > > + cpu-supply = <&vddcpu_b>;
> > > +};
> > > +
> > > +&cpu103 {
> > > + cpu-supply = <&vddcpu_b>;
> > > +};
> > > +
> > > diff --git a/arch/arm64/boot/dts/amlogic/meson-t7.dtsi b/arch/arm64/boot/dts/amlogic/meson-t7.dtsi
> > > new file mode 100644
> > > index 000000000000..453b3d9cb9d8
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/amlogic/meson-t7.dtsi
> > > @@ -0,0 +1,202 @@
> > > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > > +/*
> > > + * Copyright (c) 2019 Amlogic, Inc. All rights reserved.
> > > + */
> > > +
> > > +#include <dt-bindings/clock/mesont7-clkc.h>
> > > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > > +
> > > +/ {
> > > + compatible = "amlogic,t7";
> > > + interrupt-parent = <&gic>;
> > > + #address-cells = <2>;
> > > + #size-cells = <2>;
> > > +
> > > + cpus {
> > > + #address-cells = <0x2>;
> > > + #size-cells = <0x0>;
> > > +
> > > + cpu-map {
> > > + cluster0 {
> > > + core0 {
> > > + cpu = <&cpu100>;
> > > + };
> > > + core1 {
> > > + cpu = <&cpu101>;
> > > + };
> > > + core2 {
> > > + cpu = <&cpu102>;
> > > + };
> > > + core3 {
> > > + cpu = <&cpu103>;
> > > + };
> > > + };
> > > +
> > > + cluster1 {
> > > + core0 {
> > > + cpu = <&cpu0>;
> > > + };
> > > + core1 {
> > > + cpu = <&cpu1>;
> > > + };
> > > + core2 {
> > > + cpu = <&cpu2>;
> > > + };
> > > + core3 {
> > > + cpu = <&cpu3>;
> > > + };
> > > + };
> > > + };
> > > +
> > > + cpu100: cpu at 100 {
> > > + device_type = "cpu";
> > > + compatible = "arm,cortex-a53";
> > > + reg = <0x0 0x100>;
> > > + enable-method = "psci";
> > > + capacity-dmips-mhz = <632>;
> > > + dynamic-power-coefficient = <110>;
> > > + #cooling-cells = <2>;
> > > + };
> > > +
> > > + cpu101: cpu at 101{
> > > + device_type = "cpu";
> > > + compatible = "arm,cortex-a53";
> > > + reg = <0x0 0x101>;
> > > + enable-method = "psci";
> > > + capacity-dmips-mhz = <632>;
> > > + dynamic-power-coefficient = <110>;
> > > + #cooling-cells = <2>;
> > > + };
> > > +
> > > + cpu102: cpu at 102 {
> > > + device_type = "cpu";
> > > + compatible = "arm,cortex-a53";
> > > + reg = <0x0 0x102>;
> > > + enable-method = "psci";
> > > + capacity-dmips-mhz = <632>;
> > > + dynamic-power-coefficient = <110>;
> > > + #cooling-cells = <2>;
> > > + };
> > > +
> > > + cpu103: cpu at 103 {
> > > + device_type = "cpu";
> > > + compatible = "arm,cortex-a53";
> > > + reg = <0x0 0x103>;
> > > + enable-method = "psci";
> > > + capacity-dmips-mhz = <632>;
> > > + dynamic-power-coefficient = <110>;
> > > + #cooling-cells = <2>;
> > > + };
> > > +
> > > + cpu0: cpu at 0 {
> > > + device_type = "cpu";
> > > + compatible = "arm,cortex-a73";
> > > + reg = <0x0 0x0>;
> > > + enable-method = "psci";
> > > + capacity-dmips-mhz = <1024>;
> > > + dynamic-power-coefficient = <550>;
> > > + #cooling-cells = <2>;
> > > + };
> > > +
> > > + cpu1: cpu at 1 {
> > > + device_type = "cpu";
> > > + compatible = "arm,cortex-a73";
> > > + reg = <0x0 0x1>;
> > > + enable-method = "psci";
> > > + capacity-dmips-mhz = <1024>;
> > > + dynamic-power-coefficient = <550>;
> > > + #cooling-cells = <2>;
> > > + };
> > > +
> > > + cpu2: cpu at 2 {
> > > + device_type = "cpu";
> > > + compatible = "arm,cortex-a73";
> > > + reg = <0x0 0x2>;
> > > + enable-method = "psci";
> > > + capacity-dmips-mhz = <1024>;
> > > + dynamic-power-coefficient = <550>;
> > > + #cooling-cells = <2>;
> > > + };
> > > +
> > > + cpu3: cpu at 3 {
> > > + device_type = "cpu";
> > > + compatible = "arm,cortex-a73";
> > > + reg = <0x0 0x3>;
> > > + enable-method = "psci";
> > > + capacity-dmips-mhz = <1024>;
> > > + dynamic-power-coefficient = <550>;
> > > + #cooling-cells = <2>;
> > > + };
> > > + };
> > > +
> > > + timer {
> > > + compatible = "arm,armv8-timer";
> > > + interrupts = <GIC_PPI 13 0xff08>,
> > > + <GIC_PPI 14 0xff08>,
> > > + <GIC_PPI 11 0xff08>,
> > > + <GIC_PPI 10 0xff08>;
> > > + };
> > > +
> > > + gic: interrupt-controller at fff01000 {
> > > + compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
> > > + #interrupt-cells = <3>;
> > > + #address-cells = <0>;
> > > + interrupt-controller;
> > > + reg = <0x0 0xfff01000 0 0x1000>,
> > > + <0x0 0xfff02000 0 0x0100>;
> > > + interrupts = <GIC_PPI 9 0xf04>;
> > > + };
> > > +
> > > + psci {
> > > + compatible = "arm,psci-0.2";
> > can you double check if it is actual version 0.2?
> > most recent Amlogic SoC should support psci-1.0
> >
> > > + method = "smc";
> > > + };
> > > +
> > > + sm: secure-monitor {
> > > + compatible = "amlogic,meson-gxbb-sm";
> > > + };
> > > +
> > > + soc {
> > > + compatible = "simple-bus";
> > > + #address-cells = <2>;
> > > + #size-cells = <2>;
> > > + ranges;
> > > +
> > > + apb4: apb4 at fe000000 {
> > > + compatible = "simple-bus";
> > > + reg = <0x0 0xfe000000 0x0 0x480000>;
> > > + #address-cells = <2>;
> > > + #size-cells = <2>;
> > > + ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x480000>;
> > > +
> > > + clkc: clock-controller {
> > > + compatible = "amlogic,t7-clkc";
> > > + #clock-cells = <1>;
> > > + reg = <0x0 0x0 0x0 0x49c>,
> > > + <0x0 0x8000 0x0 0x320>,
> > > + <0x0 0xe040 0x0 0xbc>;
> > > + reg-names = "basic",
> > > + "pll",
> > > + "cpu_clk";
> > > + };
> > > +
> > > + ao-secure at 140 {
> > > + compatible = "amlogic,meson-gx-ao-secure", "syscon";
> > > + reg=<0x0 0x10220 0x0 0x140>;
> > > + amlogic,has-chip-id;
> > > + };
> > > + };
> > > +
> > > + uart_A: serial at fe078000 {
> > > + compatible = "amlogic,meson-t7-uart";
> > > + reg = <0x0 0xfe078000 0x0 0x18>;
> > > + interrupts = <0 168 1>;
> > > + status = "disabled";
> > > + clocks = <&xtal>, <&clkc CLKID_UART_A>, <&xtal>;
> > > + clock-names = "xtal", "pclk", "baud";
> > > + fifo-size = < 64 >;
> > > + pinctrl-names = "default";
> > > + };
> > I believe there are more uart ports, it's worth the effort to add them all in one run,
> > which sounds more consistent to me, anyway you could also choose to add them
> > in later patch series, no problem..
>
> Yeah, I prefer to add those uarts later, when I can propper test them.
>
> >
> > > + };
> > > +};
> > > +
> > > --
> > > 2.41.0
> > >
> > >
> > > _______________________________________________
> > > linux-amlogic mailing list
> > > linux-amlogic at lists.infradead.org
> > > http://lists.infradead.org/mailman/listinfo/linux-amlogic
> >
> > --
> > Yixun Lan (dlan)
> > Gentoo Linux Developer
> > GPG Key ID AABEFD55
The datasheet I have doesn't mention the version of PSCI supported, so
I can't check.
But It continues to work ( serial log ) when using the 1.0 version.
More information about the linux-amlogic
mailing list