[PATCH v3 2/2] mtd: rawnand: meson: waiting w/o wired ready/busy pin
Arseniy Krasnov
avkrasnov at sberdevices.ru
Tue Jul 4 05:46:18 PDT 2023
On 04.07.2023 15:43, Miquel Raynal wrote:
> Hi Arseniy,
>
> AVKrasnov at sberdevices.ru wrote on Thu, 8 Jun 2023 07:47:28 +0300:
>
>> If there is no wired ready/busy pin, classic way to wait for command
>> completion is to use function 'nand_soft_waitrdy()'. Meson NAND has
>> special command which allows to wait for NAND_STATUS_READY bit without
>> reading status in a software loop (as 'nand_soft_waitrdy()' does). To
>> use it send this command along with NAND_CMD_STATUS, then wait for an
>> interrupt, and after interrupt send NAND_CMD_READ0. So this feature
>> allows to use interrupt driven waiting without wired ready/busy pin.
>>
>> Suggested-by: Liang Yang <liang.yang at amlogic.com>
>> Signed-off-by: Arseniy Krasnov <AVKrasnov at sberdevices.ru>
>> ---
>> drivers/mtd/nand/raw/meson_nand.c | 77 +++++++++++++++++++++++++++++--
>> 1 file changed, 73 insertions(+), 4 deletions(-)
>>
>> diff --git a/drivers/mtd/nand/raw/meson_nand.c b/drivers/mtd/nand/raw/meson_nand.c
>> index 074e14225c06..9f05e113b4ea 100644
>> --- a/drivers/mtd/nand/raw/meson_nand.c
>> +++ b/drivers/mtd/nand/raw/meson_nand.c
>> @@ -38,6 +38,7 @@
>> #define NFC_CMD_SCRAMBLER_DISABLE 0
>> #define NFC_CMD_SHORTMODE_DISABLE 0
>> #define NFC_CMD_RB_INT BIT(14)
>> +#define NFC_CMD_RB_INT_NO_PIN ((0xb << 10) | BIT(18) | BIT(16))
>>
>> #define NFC_CMD_GET_SIZE(x) (((x) >> 22) & GENMASK(4, 0))
>>
>> @@ -179,6 +180,7 @@ struct meson_nfc {
>> u32 info_bytes;
>>
>> unsigned long assigned_cs;
>> + bool no_rb_pin;
>> };
>>
>> enum {
>> @@ -392,7 +394,42 @@ static void meson_nfc_set_data_oob(struct nand_chip *nand,
>> }
>> }
>>
>> -static int meson_nfc_queue_rb(struct meson_nfc *nfc, int timeout_ms)
>> +static int meson_nfc_wait_no_rb_pin(struct meson_nfc *nfc, int timeout_ms,
>> + bool need_cmd_read0)
>> +{
>> + u32 cmd, cfg;
>> +
>> + meson_nfc_cmd_idle(nfc, nfc->timing.twb);
>> + meson_nfc_drain_cmd(nfc);
>> + meson_nfc_wait_cmd_finish(nfc, CMD_FIFO_EMPTY_TIMEOUT);
>> +
>> + cfg = readl(nfc->reg_base + NFC_REG_CFG);
>> + cfg |= NFC_RB_IRQ_EN;
>> + writel(cfg, nfc->reg_base + NFC_REG_CFG);
>> +
>> + reinit_completion(&nfc->completion);
>> + cmd = nfc->param.chip_select | NFC_CMD_CLE | NAND_CMD_STATUS;
>> + writel(cmd, nfc->reg_base + NFC_REG_CMD);
>> +
>> + /* use the max erase time as the maximum clock for waiting R/B */
>> + cmd = NFC_CMD_RB | NFC_CMD_RB_INT_NO_PIN | nfc->timing.tbers_max;
>> + writel(cmd, nfc->reg_base + NFC_REG_CMD);
>> +
>> + if (!wait_for_completion_timeout(&nfc->completion,
>> + msecs_to_jiffies(timeout_ms)))
>> + return -ETIMEDOUT;
>> +
>> + if (need_cmd_read0) {
>> + cmd = nfc->param.chip_select | NFC_CMD_CLE | NAND_CMD_READ0;
>> + writel(cmd, nfc->reg_base + NFC_REG_CMD);
>> + meson_nfc_drain_cmd(nfc);
>> + meson_nfc_wait_cmd_finish(nfc, CMD_FIFO_EMPTY_TIMEOUT);
>> + }
>
> I forgot about this, you should avoid open coding core helpers, can you
> please send a followup patch to use nand_status_op() and
> nand_exit_status_op() ?
A ok, so:
1) Sending NAND_CMD_STATUS goes to nand_status_op()
2) Sending NAND_CMD_READ0 goes to nand_exit_status_op()
Ok, no problem! I'll prepare and send it on this week!
Thanks, Arseniy
>
>> +
>> + return 0;
>> +}
>> +
>> +static int meson_nfc_wait_rb_pin(struct meson_nfc *nfc, int timeout_ms)
>> {
>> u32 cmd, cfg;
>> int ret = 0;
>> @@ -420,6 +457,27 @@ static int meson_nfc_queue_rb(struct meson_nfc *nfc, int timeout_ms)
>> return ret;
>> }
>>
>> +static int meson_nfc_queue_rb(struct meson_nfc *nfc, int timeout_ms,
>> + bool need_cmd_read0)
>> +{
>> + if (nfc->no_rb_pin) {
>> + /* This mode is used when there is no wired R/B pin.
>> + * It works like 'nand_soft_waitrdy()', but instead of
>> + * polling NAND_CMD_STATUS bit in the software loop,
>> + * it will wait for interrupt - controllers checks IO
>> + * bus and when it detects NAND_CMD_STATUS on it, it
>> + * raises interrupt. After interrupt, NAND_CMD_READ0 is
>> + * sent as terminator of the ready waiting procedure if
>> + * needed (for all cases except page programming - this
>> + * is reason of 'need_cmd_read0' flag).
>> + */
>> + return meson_nfc_wait_no_rb_pin(nfc, timeout_ms,
>> + need_cmd_read0);
>> + } else {
>> + return meson_nfc_wait_rb_pin(nfc, timeout_ms);
>> + }
>> +}
>> +
>> static void meson_nfc_set_user_byte(struct nand_chip *nand, u8 *oob_buf)
>> {
>> struct meson_nfc_nand_chip *meson_chip = to_meson_nand(nand);
>> @@ -623,7 +681,7 @@ static int meson_nfc_rw_cmd_prepare_and_execute(struct nand_chip *nand,
>> if (in) {
>> nfc->cmdfifo.rw.cmd1 = cs | NFC_CMD_CLE | NAND_CMD_READSTART;
>> writel(nfc->cmdfifo.rw.cmd1, nfc->reg_base + NFC_REG_CMD);
>> - meson_nfc_queue_rb(nfc, PSEC_TO_MSEC(sdr->tR_max));
>> + meson_nfc_queue_rb(nfc, PSEC_TO_MSEC(sdr->tR_max), true);
>> } else {
>> meson_nfc_cmd_idle(nfc, nfc->timing.tadl);
>> }
>> @@ -669,7 +727,7 @@ static int meson_nfc_write_page_sub(struct nand_chip *nand,
>>
>> cmd = nfc->param.chip_select | NFC_CMD_CLE | NAND_CMD_PAGEPROG;
>> writel(cmd, nfc->reg_base + NFC_REG_CMD);
>> - meson_nfc_queue_rb(nfc, PSEC_TO_MSEC(sdr->tPROG_max));
>> + meson_nfc_queue_rb(nfc, PSEC_TO_MSEC(sdr->tPROG_max), false);
>>
>> meson_nfc_dma_buffer_release(nand, data_len, info_len, DMA_TO_DEVICE);
>>
>> @@ -952,7 +1010,8 @@ static int meson_nfc_exec_op(struct nand_chip *nand,
>> break;
>>
>> case NAND_OP_WAITRDY_INSTR:
>> - meson_nfc_queue_rb(nfc, instr->ctx.waitrdy.timeout_ms);
>> + meson_nfc_queue_rb(nfc, instr->ctx.waitrdy.timeout_ms,
>> + true);
>> if (instr->delay_ns)
>> meson_nfc_cmd_idle(nfc, delay_idle);
>> break;
>> @@ -1248,6 +1307,7 @@ meson_nfc_nand_chip_init(struct device *dev,
>> struct mtd_info *mtd;
>> int ret, i;
>> u32 tmp, nsels;
>> + u32 nand_rb_val = 0;
>>
>> nsels = of_property_count_elems_of_size(np, "reg", sizeof(u32));
>> if (!nsels || nsels > MAX_CE_NUM) {
>> @@ -1287,6 +1347,15 @@ meson_nfc_nand_chip_init(struct device *dev,
>> mtd->owner = THIS_MODULE;
>> mtd->dev.parent = dev;
>>
>> + ret = of_property_read_u32(np, "nand-rb", &nand_rb_val);
>> + if (ret == -EINVAL)
>> + nfc->no_rb_pin = true;
>> + else if (ret)
>> + return ret;
>> +
>> + if (nand_rb_val)
>> + return -EINVAL;
>> +
>> ret = nand_scan(nand, nsels);
>> if (ret)
>> return ret;
>
>
> Thanks,
> Miquèl
More information about the linux-amlogic
mailing list