[PATCH v1 3/3] arch/arm: dts: introduce meson-a1 device tree

Alexey Romanov avromanov at sberdevices.ru
Wed Feb 22 03:50:20 PST 2023


Add basic support for the 32-bit Amlogic A1. This device tree
describes following compontents: CPU, GIC, IRQ, Timer, UART,
PIN controller. It's capable of booting up into
the serial console.

This is based on arm64 version of meson-a1.dtsi.

Signed-off-by: Alexey Romanov <avromanov at sberdevices.ru>
---
 arch/arm/boot/dts/meson-a1.dtsi | 151 ++++++++++++++++++++++++++++++++
 1 file changed, 151 insertions(+)
 create mode 100644 arch/arm/boot/dts/meson-a1.dtsi

diff --git a/arch/arm/boot/dts/meson-a1.dtsi b/arch/arm/boot/dts/meson-a1.dtsi
new file mode 100644
index 000000000000..1d900fe86f8e
--- /dev/null
+++ b/arch/arm/boot/dts/meson-a1.dtsi
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2023 SberDevices.
+ * Author: Alexey Romanov <avromanov at sberdevices.ru>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/meson-a1-gpio.h>
+
+/ {
+	compatible = "amlogic,a1";
+
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu at 0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu1: cpu at 1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x1>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		l2: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	sm: secure-monitor {
+		compatible = "amlogic,meson-gxbb-sm";
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		apb: bus at fe000000 {
+			compatible = "simple-bus";
+			reg = <0xfe000000 0x1000000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xfe000000 0x1000000>;
+
+			reset: reset-controller at 0 {
+				compatible = "amlogic,meson-a1-reset";
+				reg = <0x0 0x8c>;
+				#reset-cells = <1>;
+			};
+
+			periphs_pinctrl: pinctrl at 400 {
+				compatible = "amlogic,meson-a1-periphs-pinctrl";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges;
+
+				gpio: bank at 400 {
+					reg = <0x0400 0x003c>,
+					      <0x0480 0x0118>;
+					reg-names = "mux", "gpio";
+					gpio-controller;
+					#gpio-cells = <2>;
+					gpio-ranges = <&periphs_pinctrl 0 0 62>;
+				};
+
+			};
+
+			uart_AO: serial at 1c00 {
+				compatible = "amlogic,meson-gx-uart",
+					     "amlogic,meson-ao-uart";
+				reg = <0x1c00 0x18>;
+				interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&xtal>, <&xtal>, <&xtal>;
+				clock-names = "xtal", "pclk", "baud";
+				status = "disabled";
+			};
+
+			uart_AO_B: serial at 2000 {
+				compatible = "amlogic,meson-gx-uart",
+					     "amlogic,meson-ao-uart";
+				reg = <0x2000 0x18>;
+				interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&xtal>, <&xtal>, <&xtal>;
+				clock-names = "xtal", "pclk", "baud";
+				status = "disabled";
+			};
+
+			gpio_intc: interrupt-controller at 0440 {
+				compatible = "amlogic,meson-a1-gpio-intc",
+					     "amlogic,meson-gpio-intc";
+				reg = <0x0440 0x14>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				amlogic,channel-interrupts =
+					<49 50 51 52 53 54 55 56>;
+			};
+		};
+
+		gic: interrupt-controller at ff901000 {
+			compatible = "arm,gic-400";
+			reg = <0xff901000 0x1000>,
+			      <0xff902000 0x2000>,
+			      <0xff904000 0x2000>,
+			      <0xff906000 0x2000>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9
+				(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13
+			(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14
+			(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11
+			(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10
+			(GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	xtal: xtal-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "xtal";
+		#clock-cells = <0>;
+	};
+};
-- 
2.38.1




More information about the linux-amlogic mailing list