[PATCH v4] docs: dt-bindings: add DTS Coding Style document
Krzysztof Kozlowski
krzysztof.kozlowski at linaro.org
Sun Dec 3 09:46:22 PST 2023
Document preferred coding style for Devicetree sources (DTS and DTSI),
to bring consistency among all (sub)architectures and ease in reviews.
Cc: Andrew Davis <afd at ti.com>
cc: Andrew Lunn <andrew at lunn.ch>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno at collabora.com>
Cc: Arnd Bergmann <arnd at arndb.de>
Cc: Bjorn Andersson <andersson at kernel.org>
Cc: Chen-Yu Tsai <wens at kernel.org>
Cc: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
Cc: Jonathan Corbet <corbet at lwn.net>
Cc: Matthias Brugger <matthias.bgg at gmail.com>
Cc: Michal Simek <michal.simek at amd.com>
Cc: Neil Armstrong <neil.armstrong at linaro.org>
Cc: Nishanth Menon <nm at ti.com>
Cc: Olof Johansson <olof at lixom.net>
Cc: Rafał Miłecki <zajec5 at gmail.com>
Acked-by: Neil Armstrong <neil.armstrong at linaro.org>
Acked-by: Heiko Stuebner <heiko at sntech.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
Acked-by: Konrad Dybcio <konradybcio at kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas at glider.be>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org>
---
Merging idea: Rob/DT bindings
Changes in v4
=============
1. Drop label at the top (Jon)
2. Grammar fixes (Laurent, Dragan)
3. "Unless a bus defines differently, unit addresses shall ..." (Rob)
4. Use hex in example of dma-controller (Andrew)
5. Example: soc@ -> soc at 0
6. Reverse points 2 and 3 in "Indentation" (Andrew)
7. Use full path to coding style doc (Conor)
Changes in v3
=============
1. should->shall (Angelo)
2. Comments // -> /* (Angelo, Michal)
3. Use imaginary example in "Order of Properties in Device Node"
(Angelo)
4. Added paragraphs for three sections with justifications of chosen
style.
5. Allow two style of ordering overrides in board DTS: alphabetically or
by order of DTSI (Rob).
6. I did not incorporate feedback about, due to lack of consensus and my
disagreement:
a. SoM being DTS without DTSI in "Organizing DTSI and DTS"
Changes in v2
=============
1. Hopefully incorporate entire feedback from comments:
a. Fix \ { => / { (Rob)
b. Name: dts-coding-style (Rob)
c. Exceptions for ordering nodes by name for Renesas and pinctrl (Geert,
Konrad)
d. Ordering properties by common/vendor (Rob)
e. Array entries in <> (Rob)
2. New chapter: Organizing DTSI and DTS
3. Several grammar fixes (missing articles)
Cc: linux-rockchip at lists.infradead.org
Cc: linux-mediatek at lists.infradead.org
Cc: linux-samsung-soc at vger.kernel.org
Cc: linux-amlogic at lists.infradead.org
Cc: linux-arm-kernel at lists.infradead.org
Cc: linux-arm-msm at vger.kernel.org
Cc: workflows at vger.kernel.org
Cc: linux-doc at vger.kernel.org
---
.../devicetree/bindings/dts-coding-style.rst | 196 ++++++++++++++++++
Documentation/devicetree/bindings/index.rst | 1 +
2 files changed, 197 insertions(+)
create mode 100644 Documentation/devicetree/bindings/dts-coding-style.rst
diff --git a/Documentation/devicetree/bindings/dts-coding-style.rst b/Documentation/devicetree/bindings/dts-coding-style.rst
new file mode 100644
index 000000000000..ffd7617f95fa
--- /dev/null
+++ b/Documentation/devicetree/bindings/dts-coding-style.rst
@@ -0,0 +1,196 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=====================================
+Devicetree Sources (DTS) Coding Style
+=====================================
+
+When writing Devicetree Sources (DTS) please observe below guidelines. They
+should be considered complementary to any rules expressed already in
+the Devicetree Specification and the dtc compiler (including W=1 and W=2
+builds).
+
+Individual architectures and subarchitectures can define additional rules,
+making the coding style stricter.
+
+Naming and Valid Characters
+---------------------------
+
+The Devicetree Specification allows a broad range of characters in node
+and property names, but this coding style narrows the range down to achieve
+better code readability.
+
+1. Node and property names can use only the following characters:
+
+ * Lowercase characters: [a-z]
+ * Digits: [0-9]
+ * Dash: -
+
+2. Labels can use only the following characters:
+
+ * Lowercase characters: [a-z]
+ * Digits: [0-9]
+ * Underscore: _
+
+3. Unless a bus defines differently, unit addresses shall use lowercase
+ hexadecimal digits, without leading zeros (padding).
+
+4. Hex values in properties, e.g. "reg", shall use lowercase hex. The address
+ part can be padded with leading zeros.
+
+Example::
+
+ gpi_dma2: dma-controller at a00000 {
+ compatible = "qcom,sm8550-gpi-dma", "qcom,sm6350-gpi-dma";
+ reg = <0x0 0x00a00000 0x0 0x60000>;
+ }
+
+Order of Nodes
+--------------
+
+1. Nodes on any bus, thus using unit addresses for children, shall be
+ ordered by unit address in ascending order.
+ Alternatively for some subarchitectures, nodes of the same type can be
+ grouped together, e.g. all I2C controllers one after another even if this
+ breaks unit address ordering.
+
+2. Nodes without unit addresses shall be ordered alpha-numerically by the node
+ name. For a few node types, they can be ordered by the main property, e.g.
+ pin configuration states ordered by value of "pins" property.
+
+3. When extending nodes in the board DTS via &label, the entries shall be
+ ordered either alpha-numerically or by keeping the order from DTSI, where
+ the choice depends on the subarchitecture.
+
+The above-described ordering rules are easy to enforce during review, reduce
+chances of conflicts for simultaneous additions of new nodes to a file and help
+in navigating through the DTS source.
+
+Example::
+
+ /* SoC DTSI */
+
+ / {
+ cpus {
+ /* ... */
+ };
+
+ psci {
+ /* ... */
+ };
+
+ soc at 0 {
+ dma: dma-controller at 10000 {
+ /* ... */
+ };
+
+ clk: clock-controller at 80000 {
+ /* ... */
+ };
+ };
+ };
+
+ /* Board DTS - alphabetical order */
+
+ &clk {
+ /* ... */
+ };
+
+ &dma {
+ /* ... */
+ };
+
+ /* Board DTS - alternative order, keep as DTSI */
+
+ &dma {
+ /* ... */
+ };
+
+ &clk {
+ /* ... */
+ };
+
+Order of Properties in Device Node
+----------------------------------
+
+The following order of properties in device nodes is preferred:
+
+1. compatible
+2. reg
+3. ranges
+4. Standard/common properties (defined by common bindings, e.g. without
+ vendor-prefixes)
+5. Vendor-specific properties
+6. status (if applicable)
+7. Child nodes, where each node is preceded with a blank line
+
+The "status" property is by default "okay", thus it can be omitted.
+
+The above-described ordering follows this approach:
+
+1. Most important properties start the node: compatible then bus addressing to
+ match unit address.
+2. Each node will have common properties in similar place.
+3. Status is the last information to annotate that device node is or is not
+ finished (board resources are needed).
+
+Example::
+
+ /* SoC DTSI */
+
+ device_node: device-class at 6789abc {
+ compatible = "vendor,device";
+ reg = <0x0 0x06789abc 0x0 0xa123>;
+ ranges = <0x0 0x0 0x06789abc 0x1000>;
+ #dma-cells = <1>;
+ clocks = <&clock_controller 0>, <&clock_controller 1>;
+ clock-names = "bus", "host";
+ vendor,custom-property = <2>;
+ status = "disabled";
+
+ child_node: child-class at 100 {
+ reg = <0x100 0x200>;
+ /* ... */
+ };
+ };
+
+ /* Board DTS */
+
+ &device_node {
+ vdd-supply = <&board_vreg1>;
+ status = "okay";
+ }
+
+Indentation
+-----------
+
+1. Use indentation according to Documentation/process/coding-style.rst.
+2. Each entry in arrays with multiple cells, e.g. "reg" with two IO addresses,
+ shall be enclosed in <>.
+3. For arrays spanning across lines, it is preferred to align the continued
+ entries with opening < from the first line.
+
+Example::
+
+ thermal-sensor at c271000 {
+ compatible = "qcom,sm8550-tsens", "qcom,tsens-v2";
+ reg = <0x0 0x0c271000 0x0 0x1000>,
+ <0x0 0x0c222000 0x0 0x1000>;
+ };
+
+Organizing DTSI and DTS
+-----------------------
+
+The DTSI and DTS files shall be organized in a way representing the common,
+reusable parts of hardware. Typically, this means organizing DTSI and DTS files
+into several files:
+
+1. DTSI with contents of the entire SoC, without nodes for hardware not present
+ on the SoC.
+2. If applicable: DTSI with common or re-usable parts of the hardware, e.g.
+ entire System-on-Module.
+3. DTS representing the board.
+
+Hardware components that are present on the board shall be placed in the
+board DTS, not in the SoC or SoM DTSI. A partial exception is a common
+external reference SoC input clock, which could be coded as a fixed-clock in
+the SoC DTSI with its frequency provided by each board DTS.
diff --git a/Documentation/devicetree/bindings/index.rst b/Documentation/devicetree/bindings/index.rst
index d9002a3a0abb..cc1fbdc05657 100644
--- a/Documentation/devicetree/bindings/index.rst
+++ b/Documentation/devicetree/bindings/index.rst
@@ -4,6 +4,7 @@
:maxdepth: 1
ABI
+ dts-coding-style
writing-bindings
writing-schema
submitting-patches
--
2.34.1
More information about the linux-amlogic
mailing list