[RFC PATCH 2/2] arm64: dts: add support for C3 based Amlogic AW409

=Xianwei Zhao xianwei.zhao at amlogic.com
Wed Apr 19 00:38:34 PDT 2023


From: Xianwei Zhao <xianwei.zhao at amlogic.com>

Amlogic C3 is an advanced edge AI processor designed for smart IP camera
applications.

Add basic support for the C3 based Amlogic AW409 board, which describes
the following components: CPU, GIC, IRQ, Timer, UART. It's capable of
booting up into the serial console.

Signed-off-by: Xianwei Zhao <xianwei.zhao at amlogic.com>
---
 arch/arm64/boot/dts/amlogic/Makefile          |  1 +
 .../amlogic/amlogic-c3-c302x-aw409-256m.dts   | 30 +++++++
 arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi   | 87 +++++++++++++++++++
 3 files changed, 118 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/amlogic-c3-c302x-aw409-256m.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index cd1c5b04890a..d2b5d0d750bc 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -74,3 +74,4 @@ dtb-$(CONFIG_ARCH_MESON) += meson-sm1-odroid-hc4.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-sei610.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-x96-air-gbit.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-x96-air.dtb
+dtb-$(CONFIG_ARCH_AMLIPC) += amlogic-c3-c302x-aw409-256m.dtb
diff --git a/arch/arm64/boot/dts/amlogic/amlogic-c3-c302x-aw409-256m.dts b/arch/arm64/boot/dts/amlogic/amlogic-c3-c302x-aw409-256m.dts
new file mode 100644
index 000000000000..38ca98a32181
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/amlogic-c3-c302x-aw409-256m.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Amlogic, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "amlogic-c3.dtsi"
+
+/ {
+	model = "Amlogic C302 aw409 Development Board";
+	compatible = "amlogic,aw409", "amlogic,c3";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		serial0 = &uart_B;
+	};
+
+	memory at 0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x10000000>;
+	};
+
+};
+
+&uart_B {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi b/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi
new file mode 100644
index 000000000000..c69072ac57f5
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Amlogic, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu0: cpu at 0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+		};
+
+		cpu1: cpu at 1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+		};
+
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	xtal: xtal-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "xtal";
+		#clock-cells = <0>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		gic: interrupt-controller at fff01000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x0 0xfff01000 0 0x1000>,
+			      <0x0 0xfff02000 0 0x2000>,
+			      <0x0 0xfff04000 0 0x2000>,
+			      <0x0 0xfff06000 0 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		apb4: apb4 at fe000000 {
+			compatible = "simple-bus";
+			reg = <0x0 0xfe000000 0x0 0x480000>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x480000>;
+
+			uart_B: serial at 7a000 {
+				compatible = "amlogic,meson-g12a-uart";
+				reg = <0x0 0x7a000 0x0 0x18>;
+				interrupts = <GIC_SPI 169 IRQ_TYPE_EDGE_RISING>;
+				status = "disabled";
+				clocks = <&xtal>, <&xtal>, <&xtal>;
+				clock-names = "xtal", "pclk", "baud";
+			};
+
+		};
+	};
+};
-- 
2.37.1




More information about the linux-amlogic mailing list