[PATCH v12 6/6] clk: meson: a1: add Amlogic A1 Peripherals clock controller driver

Dmitry Rokosov ddrokosov at sberdevices.ru
Wed Apr 5 07:55:15 PDT 2023


On Wed, Apr 05, 2023 at 04:13:44PM +0200, Jerome Brunet wrote:
> 
> On Tue 04 Apr 2023 at 18:53, Dmitry Rokosov <ddrokosov at sberdevices.ru> wrote:
> 
> > +/* Array of all clocks registered by this provider */
> > +static struct clk_hw_onecell_data a1_periphs_clks = {
> > +	.hws = {
> > +		/* DT exposed clocks */
> > +		[CLKID_FIXPLL_IN]		= &fixpll_in.hw,
> > +		[CLKID_USB_PHY_IN]		= &usb_phy_in.hw,
> > +		[CLKID_USB_CTRL_IN]		= &usb_ctrl_in.hw,
> > +		[CLKID_HIFIPLL_IN]		= &hifipll_in.hw,
> > +		[CLKID_SYSPLL_IN]		= &syspll_in.hw,
> > +		[CLKID_DDS_IN]			= &dds_in.hw,
> > +		[CLKID_SYS]			= &sys.hw,
> > +		[CLKID_CLKTREE]			= &clktree.hw,
> > +		[CLKID_RESET_CTRL]		= &reset_ctrl.hw,
> > +		[CLKID_ANALOG_CTRL]		= &analog_ctrl.hw,
> > +		[CLKID_PWR_CTRL]		= &pwr_ctrl.hw,
> > +		[CLKID_PAD_CTRL]		= &pad_ctrl.hw,
> > +		[CLKID_SYS_CTRL]		= &sys_ctrl.hw,
> > +		[CLKID_TEMP_SENSOR]		= &temp_sensor.hw,
> > +		[CLKID_AM2AXI_DIV]		= &am2axi_dev.hw,
> > +		[CLKID_SPICC_B]			= &spicc_b.hw,
> > +		[CLKID_SPICC_A]			= &spicc_a.hw,
> > +		[CLKID_MSR]			= &msr.hw,
> > +		[CLKID_AUDIO]			= &audio.hw,
> > +		[CLKID_JTAG_CTRL]		= &jtag_ctrl.hw,
> > +		[CLKID_SARADC_EN]		= &saradc_en.hw,
> > +		[CLKID_PWM_EF]			= &pwm_ef.hw,
> > +		[CLKID_PWM_CD]			= &pwm_cd.hw,
> > +		[CLKID_PWM_AB]			= &pwm_ab.hw,
> > +		[CLKID_CEC]			= &cec.hw,
> > +		[CLKID_I2C_S]			= &i2c_s.hw,
> > +		[CLKID_IR_CTRL]			= &ir_ctrl.hw,
> > +		[CLKID_I2C_M_D]			= &i2c_m_d.hw,
> > +		[CLKID_I2C_M_C]			= &i2c_m_c.hw,
> > +		[CLKID_I2C_M_B]			= &i2c_m_b.hw,
> > +		[CLKID_I2C_M_A]			= &i2c_m_a.hw,
> > +		[CLKID_ACODEC]			= &acodec.hw,
> > +		[CLKID_OTP]			= &otp.hw,
> > +		[CLKID_SD_EMMC_A]		= &sd_emmc_a.hw,
> > +		[CLKID_USB_PHY]			= &usb_phy.hw,
> > +		[CLKID_USB_CTRL]		= &usb_ctrl.hw,
> > +		[CLKID_SYS_DSPB]		= &sys_dspb.hw,
> > +		[CLKID_SYS_DSPA]		= &sys_dspa.hw,
> > +		[CLKID_DMA]			= &dma.hw,
> > +		[CLKID_IRQ_CTRL]		= &irq_ctrl.hw,
> > +		[CLKID_NIC]			= &nic.hw,
> > +		[CLKID_GIC]			= &gic.hw,
> > +		[CLKID_UART_C]			= &uart_c.hw,
> > +		[CLKID_UART_B]			= &uart_b.hw,
> > +		[CLKID_UART_A]			= &uart_a.hw,
> > +		[CLKID_SYS_PSRAM]		= &sys_psram.hw,
> > +		[CLKID_RSA]			= &rsa.hw,
> > +		[CLKID_CORESIGHT]		= &coresight.hw,
> > +		[CLKID_AM2AXI_VAD]		= &am2axi_vad.hw,
> > +		[CLKID_AUDIO_VAD]		= &audio_vad.hw,
> > +		[CLKID_AXI_DMC]			= &axi_dmc.hw,
> > +		[CLKID_AXI_PSRAM]		= &axi_psram.hw,
> > +		[CLKID_RAMB]			= &ramb.hw,
> > +		[CLKID_RAMA]			= &rama.hw,
> > +		[CLKID_AXI_SPIFC]		= &axi_spifc.hw,
> > +		[CLKID_AXI_NIC]			= &axi_nic.hw,
> > +		[CLKID_AXI_DMA]			= &axi_dma.hw,
> > +		[CLKID_CPU_CTRL]		= &cpu_ctrl.hw,
> > +		[CLKID_ROM]			= &rom.hw,
> > +		[CLKID_PROC_I2C]		= &prod_i2c.hw,
> > +		[CLKID_DSPA_EN]			= &dspa_en.hw,
> > +		[CLKID_DSPA_EN_NIC]		= &dspa_en_nic.hw,
> > +		[CLKID_DSPB_EN]			= &dspb_en.hw,
> > +		[CLKID_DSPB_EN_NIC]		= &dspb_en_nic.hw,
> > +		[CLKID_RTC]			= &rtc.hw,
> > +		[CLKID_CECA_32K]		= &ceca_32k_out.hw,
> > +		[CLKID_CECB_32K]		= &cecb_32k_out.hw,
> > +		[CLKID_24M]			= &clk_24m.hw,
> > +		[CLKID_12M]			= &clk_12m.hw,
> > +		[CLKID_FCLK_DIV2_DIVN]		= &fclk_div2_divn.hw,
> > +		[CLKID_GEN]			= &gen.hw,
> > +		[CLKID_SARADC]			= &saradc.hw,
> > +		[CLKID_PWM_A]			= &pwm_a.hw,
> > +		[CLKID_PWM_B]			= &pwm_b.hw,
> > +		[CLKID_PWM_C]			= &pwm_c.hw,
> > +		[CLKID_PWM_D]			= &pwm_d.hw,
> > +		[CLKID_PWM_E]			= &pwm_e.hw,
> > +		[CLKID_PWM_F]			= &pwm_f.hw,
> > +		[CLKID_SPICC]			= &spicc.hw,
> > +		[CLKID_TS]			= &ts.hw,
> > +		[CLKID_SPIFC]			= &spifc.hw,
> > +		[CLKID_USB_BUS]			= &usb_bus.hw,
> > +		[CLKID_SD_EMMC]			= &sd_emmc.hw,
> > +		[CLKID_PSRAM]			= &psram.hw,
> > +		[CLKID_DMC]			= &dmc.hw,
> > +		[CLKID_GEN_SEL]			= &gen_sel.hw,
> > +		[CLKID_PWM_A_SEL]		= &pwm_a_sel.hw,
> > +		[CLKID_PWM_B_SEL]		= &pwm_b_sel.hw,
> > +		[CLKID_PWM_C_SEL]		= &pwm_c_sel.hw,
> > +		[CLKID_PWM_D_SEL]		= &pwm_d_sel.hw,
> > +		[CLKID_PWM_E_SEL]		= &pwm_e_sel.hw,
> > +		[CLKID_PWM_F_SEL]		= &pwm_f_sel.hw,
> > +		[CLKID_DSPA_A_SEL]		= &dspa_a_sel.hw,
> > +		[CLKID_DSPA_B_SEL]		= &dspa_b_sel.hw,
> > +		[CLKID_DSPB_A_SEL]		= &dspb_a_sel.hw,
> > +		[CLKID_DSPB_B_SEL]		= &dspb_b_sel.hw,
> > +		[CLKID_CECA_32K_SEL]		= &ceca_32k_sel.hw,
> > +		[CLKID_CECA_32K_SEL_PRE]	= &ceca_32k_sel_pre.hw,
> > +		[CLKID_CECB_32K_SEL]		= &cecb_32k_sel.hw,
> > +		[CLKID_CECB_32K_SEL_PRE]	= &cecb_32k_sel_pre.hw,
> > +
> > +		/* Internal clocks */
> 
> There is no need to make such groups within the table.
> I don't think such change was requested in the previous reviews.
> 
> Also grouping the IDs the way you did is a bad idea.
> 
> 1) Since the clocks are registered in the order of the table, this will
> make a lot of orphans during the registration of the controller. It does
> work but it is not ideal performance wise. Whenever possible, it is
> better to register the clocks from the roots to the leafs.
> 
> 2) These 2 nice groups are going away the minute you add another clock which
> was not part of the original submission. This is why IDs have no meaning,
> no even groups.
> 

In my opinion, it would be clearer to have two separate lists for 'exposed'
and 'internal' clocks. Krzysztof has previously mentioned that non-linear
IDs in the bindings are not a good solution, but I understand the argument
for improved performance. Therefore, I will change the ID order from root to
leaf nodes.

> > +		[CLKID_XTAL_IN]			= &xtal_in.hw,
> > +		[CLKID_DSPA_SEL]		= &dspa_sel.hw,
> > +		[CLKID_DSPB_SEL]		= &dspb_sel.hw,
> > +		[CLKID_SARADC_SEL]		= &saradc_sel.hw,
> > +		[CLKID_SYS_A_SEL]		= &sys_a_sel.hw,
> > +		[CLKID_SYS_A_DIV]		= &sys_a_div.hw,
> > +		[CLKID_SYS_A]			= &sys_a.hw,
> > +		[CLKID_SYS_B_SEL]		= &sys_b_sel.hw,
> > +		[CLKID_SYS_B_DIV]		= &sys_b_div.hw,
> > +		[CLKID_SYS_B]			= &sys_b.hw,
> > +		[CLKID_DSPA_A_DIV]		= &dspa_a_div.hw,
> > +		[CLKID_DSPA_A]			= &dspa_a.hw,
> > +		[CLKID_DSPA_B_DIV]		= &dspa_b_div.hw,
> > +		[CLKID_DSPA_B]			= &dspa_b.hw,
> > +		[CLKID_DSPB_A_DIV]		= &dspb_a_div.hw,
> > +		[CLKID_DSPB_A]			= &dspb_a.hw,
> > +		[CLKID_DSPB_B_DIV]		= &dspb_b_div.hw,
> > +		[CLKID_DSPB_B]			= &dspb_b.hw,
> > +		[CLKID_RTC_32K_IN]		= &rtc_32k_in.hw,
> > +		[CLKID_RTC_32K_DIV]		= &rtc_32k_div.hw,
> > +		[CLKID_RTC_32K_XTAL]		= &rtc_32k_xtal.hw,
> > +		[CLKID_RTC_32K_SEL]		= &rtc_32k_sel.hw,
> > +		[CLKID_CECB_32K_IN]		= &cecb_32k_in.hw,
> > +		[CLKID_CECB_32K_DIV]		= &cecb_32k_div.hw,
> > +		[CLKID_CECA_32K_IN]		= &ceca_32k_in.hw,
> > +		[CLKID_CECA_32K_DIV]		= &ceca_32k_div.hw,
> > +		[CLKID_DIV2_PRE]		= &fclk_div2_divn_pre.hw,
> > +		[CLKID_24M_DIV2]		= &clk_24m_div2.hw,
> > +		[CLKID_GEN_DIV]			= &gen_div.hw,
> > +		[CLKID_SARADC_DIV]		= &saradc_div.hw,
> > +		[CLKID_PWM_A_DIV]		= &pwm_a_div.hw,
> > +		[CLKID_PWM_B_DIV]		= &pwm_b_div.hw,
> > +		[CLKID_PWM_C_DIV]		= &pwm_c_div.hw,
> > +		[CLKID_PWM_D_DIV]		= &pwm_d_div.hw,
> > +		[CLKID_PWM_E_DIV]		= &pwm_e_div.hw,
> > +		[CLKID_PWM_F_DIV]		= &pwm_f_div.hw,
> > +		[CLKID_SPICC_SEL]		= &spicc_sel.hw,
> > +		[CLKID_SPICC_DIV]		= &spicc_div.hw,
> > +		[CLKID_SPICC_SEL2]		= &spicc_sel2.hw,
> > +		[CLKID_TS_DIV]			= &ts_div.hw,
> > +		[CLKID_SPIFC_SEL]		= &spifc_sel.hw,
> > +		[CLKID_SPIFC_DIV]		= &spifc_div.hw,
> > +		[CLKID_SPIFC_SEL2]		= &spifc_sel2.hw,
> > +		[CLKID_USB_BUS_SEL]		= &usb_bus_sel.hw,
> > +		[CLKID_USB_BUS_DIV]		= &usb_bus_div.hw,
> > +		[CLKID_SD_EMMC_SEL]		= &sd_emmc_sel.hw,
> > +		[CLKID_SD_EMMC_DIV]		= &sd_emmc_div.hw,
> > +		[CLKID_SD_EMMC_SEL2]		= &sd_emmc_sel2.hw,
> > +		[CLKID_PSRAM_SEL]		= &psram_sel.hw,
> > +		[CLKID_PSRAM_DIV]		= &psram_div.hw,
> > +		[CLKID_PSRAM_SEL2]		= &psram_sel2.hw,
> > +		[CLKID_DMC_SEL]			= &dmc_sel.hw,
> > +		[CLKID_DMC_DIV]			= &dmc_div.hw,
> > +		[CLKID_DMC_SEL2]		= &dmc_sel2.hw,
> > +
> > +		[NR_CLKS]			= NULL,
> > +	},
> > +	.num = NR_CLKS,
> > +};

-- 
Thank you,
Dmitry



More information about the linux-amlogic mailing list