[PATCH 14/15] iio: health: max30102: do not use internal iio_dev lock

[Jonathan Cameron]

On Tue, 20 Sep 2022 13:28:20 +0200
Nuno Sá <nuno.sa at analog.com> wrote:

> The pattern used in this device does not quite fit in the
> iio_device_claim_direct_mode() typical usage. In this case,
> iio_buffer_enabled() was being used not to prevent the raw access
> but to decide whether or not the device needs to be powered on before.
> If buffering, then the device is already on. To guarantee the same
> behavior, a combination of locks is being used:
> 
> 1. Use iio_device_claim_direct_mode() to check if direct mode can be
> claimed and if we can, then we keep it until the reading is done (which
> also means the device will be powered on and off);
> 2. If already buffering, we need to make sure that buffering is not
> disabled (and hence, powering off the device) while doing a raw read. For
> that, we can make use of the local lock that already exists.
> 
> Signed-off-by: Nuno Sá <nuno.sa at analog.com>
Obviously same dance in here as the related previous patch. So same solution
needs adopting.  I just thought I'd reply to make sure we didn't forget to
cover them both :)

Jonathan


> ---
>  drivers/iio/health/max30102.c | 25 +++++++++++++++++++------
>  1 file changed, 19 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/iio/health/max30102.c b/drivers/iio/health/max30102.c
> index abbcef563807..e984c78b99f6 100644
> --- a/drivers/iio/health/max30102.c
> +++ b/drivers/iio/health/max30102.c
> @@ -227,9 +227,20 @@ static int max30102_buffer_postenable(struct iio_dev *indio_dev)
>  static int max30102_buffer_predisable(struct iio_dev *indio_dev)
>  {
>  	struct max30102_data *data = iio_priv(indio_dev);
> +	int ret;
> +
> +	/*
> +	 * As stated in the comment in the read_raw() function, temperature
> +	 * can only be acquired if the engine is running. As such the mutex
> +	 * is used to make sure we do not power down while doing a temperature
> +	 * reading.
> +	 */
> +	mutex_lock(&data->lock);
> +	ret = max30102_set_powermode(data, MAX30102_REG_MODE_CONFIG_MODE_NONE,
> +				     false);
> +	mutex_unlock(&data->lock);
>  
> -	return max30102_set_powermode(data, MAX30102_REG_MODE_CONFIG_MODE_NONE,
> -				      false);
> +	return ret;
>  }
>  
>  static const struct iio_buffer_setup_ops max30102_buffer_setup_ops = {
> @@ -477,12 +488,14 @@ static int max30102_read_raw(struct iio_dev *indio_dev,
>  		 * Temperature reading can only be acquired when not in
>  		 * shutdown; leave shutdown briefly when buffer not running
>  		 */
> -		mutex_lock(&indio_dev->mlock);
> -		if (!iio_buffer_enabled(indio_dev))
> +		if (!iio_device_claim_direct_mode(indio_dev)) {
>  			ret = max30102_get_temp(data, val, true);
> -		else
> +			iio_device_release_direct_mode(indio_dev);
> +		} else {
> +			mutex_lock(&data->lock);
>  			ret = max30102_get_temp(data, val, false);
> -		mutex_unlock(&indio_dev->mlock);
> +			mutex_unlock(&data->lock);
> +		}
>  		if (ret)
>  			return ret;
>