[PATCH 4/4] arm64: dts: amlogic: add initial Odroid Go Ultra DTS
Neil Armstrong
neil.armstrong at linaro.org
Mon Oct 31 09:47:28 PDT 2022
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- Earphone stereo jack detect
- 5inch 854×480 MIPI-DSI TFT LCD
Signed-off-by: Neil Armstrong <neil.armstrong at linaro.org>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../dts/amlogic/meson-g12b-odroid-go-ultra.dts | 730 +++++++++++++++++++++
2 files changed, 731 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index e213aeebb774..97b42e2100e0 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -12,6 +12,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gsking-x.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-go-ultra.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-go-ultra.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-go-ultra.dts
new file mode 100644
index 000000000000..3bda11b37d5e
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-go-ultra.dts
@@ -0,0 +1,730 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Neil Armstrong <neil.armstrong at linaro.org>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b-s922x.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-toacodec.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+ compatible = "hardkernel,odroid-go-ultra", "amlogic,s922x", "amlogic,g12b";
+ model = "Hardkernel ODROID-GO-Ultra";
+
+ aliases {
+ serial0 = &uart_AO;
+ rtc0 = &vrtc;
+ };
+
+ adc-joystick-left {
+ compatible = "adc-joystick";
+ io-channels = <&saradc 2>, <&saradc 3>;
+ poll-interval = <10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ axis at 0 {
+ reg = <0>;
+ linux,code = <ABS_Y>;
+ abs-range = <3150 950>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ axis at 1 {
+ reg = <1>;
+ linux,code = <ABS_X>;
+ abs-range = <700 2900>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ };
+
+ adc-joystick-right {
+ compatible = "adc-joystick";
+ io-channels = <&saradc 0>, <&saradc 1>;
+ poll-interval = <10>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ axis at 0 {
+ reg = <0>;
+ linux,code = <ABS_RY>;
+ abs-range = <3150 950>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ axis at 1 {
+ reg = <1>;
+ linux,code = <ABS_RX>;
+ abs-range = <800 3000>;
+ abs-fuzz = <32>;
+ abs-flat = <64>;
+ };
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ codec_clk: codec-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <12288000>;
+ clock-output-names = "codec_clk";
+ #clock-cells = <0>;
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ poll-interval = <10>;
+ pinctrl-0 = <&keypad_gpio_pins>;
+ pinctrl-names = "default";
+
+ volume-up-button {
+ label = "VOLUME-UP";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&gpio GPIOX_8 GPIO_ACTIVE_LOW>;
+ };
+ volume-down-button {
+ label = "VOLUME-DOWN";
+ linux,code = <KEY_VOLUMEDOWN>;
+ gpios = <&gpio GPIOX_9 GPIO_ACTIVE_LOW>;
+ };
+ dpad-up-button {
+ label = "DPAD-UP";
+ linux,code = <BTN_DPAD_UP>;
+ gpios = <&gpio GPIOX_0 GPIO_ACTIVE_LOW>;
+ };
+ dpad-down-button {
+ label = "DPAD-DOWN";
+ linux,code = <BTN_DPAD_DOWN>;
+ gpios = <&gpio GPIOX_1 GPIO_ACTIVE_LOW>;
+ };
+ dpad-left-button {
+ label = "DPAD-LEFT";
+ linux,code = <BTN_DPAD_LEFT>;
+ gpios = <&gpio GPIOX_2 GPIO_ACTIVE_LOW>;
+ };
+ dpad-right-button {
+ label = "DPAD-RIGHT";
+ linux,code = <BTN_DPAD_RIGHT>;
+ gpios = <&gpio GPIOX_3 GPIO_ACTIVE_LOW>;
+ };
+ a-button {
+ label = "A";
+ linux,code = <BTN_EAST>;
+ gpios = <&gpio GPIOX_4 GPIO_ACTIVE_LOW>;
+ };
+ b-button {
+ label = "B";
+ linux,code = <BTN_SOUTH>;
+ gpios = <&gpio GPIOX_5 GPIO_ACTIVE_LOW>;
+ };
+ y-button {
+ label = "Y";
+ linux,code = <BTN_WEST>;
+ gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ };
+ x-button {
+ label = "X";
+ linux,code = <BTN_NORTH>;
+ gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+ };
+ f1-button {
+ label = "F1";
+ linux,code = <BTN_TRIGGER_HAPPY1>;
+ gpios = <&gpio GPIOX_17 GPIO_ACTIVE_LOW>;
+ };
+ f2-button {
+ label = "F2";
+ linux,code = <BTN_TRIGGER_HAPPY2>;
+ gpios = <&gpio GPIOX_10 GPIO_ACTIVE_LOW>;
+ };
+ f3-button {
+ label = "F3";
+ linux,code = <BTN_TRIGGER_HAPPY3>;
+ gpios = <&gpio GPIOX_11 GPIO_ACTIVE_LOW>;
+ };
+ f4-button {
+ label = "F4";
+ linux,code = <BTN_TRIGGER_HAPPY4>;
+ gpios = <&gpio GPIOX_12 GPIO_ACTIVE_LOW>;
+ };
+ f5-button {
+ label = "F5";
+ linux,code = <BTN_TRIGGER_HAPPY5>;
+ gpios = <&gpio GPIOX_13 GPIO_ACTIVE_LOW>;
+ };
+ f6-button {
+ label = "F6";
+ linux,code = <BTN_TRIGGER_HAPPY6>;
+ gpios = <&gpio GPIOX_16 GPIO_ACTIVE_LOW>;
+ };
+ top-left-button {
+ label = "TOP Left";
+ linux,code = <BTN_TL>;
+ gpios = <&gpio GPIOX_14 GPIO_ACTIVE_LOW>;
+ };
+ top-left2-button {
+ label = "TOP Left 2";
+ linux,code = <BTN_TL2>;
+ gpios = <&gpio GPIOX_19 GPIO_ACTIVE_LOW>;
+ };
+ top-right-button {
+ label = "TOP Right";
+ linux,code = <BTN_TR>;
+ gpios = <&gpio GPIOX_15 GPIO_ACTIVE_LOW>;
+ };
+ top-right2-button {
+ label = "TOP Right 2";
+ linux,code = <BTN_TR2>;
+ gpios = <&gpio GPIOX_18 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-blue {
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ poweroff {
+ compatible = "hardkernel,odroid-go-ultra-poweroff";
+ hardkernel,rk817-pmic = <&rk817>;
+ hardkernel,rk818-pmic = <&rk818>;
+ };
+
+ vdd_sys: regulator-vdd_sys {
+ compatible = "regulator-fixed";
+ regulator-name = "VDD_SYS";
+ regulator-min-microvolt = <3800000>;
+ regulator-max-microvolt = <3800000>;
+ regulator-always-on;
+ };
+
+ sound {
+ compatible = "amlogic,axg-sound-card";
+ model = "Odroid GO Ultra";
+ audio-widgets = "Microphone", "Mic Jack",
+ "Headphone", "Headphones",
+ "Speaker", "Internal Speakers";
+ audio-aux-devs = <&tdmout_b>, <&tdmin_b>, <&speaker_amp>;
+ audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+ "TDM_B Playback", "TDMOUT_B OUT",
+ "TDMIN_B IN 1", "TDM_B Capture",
+ "TDMIN_B IN 4", "TDM_B Loopback",
+ "TODDR_A IN 1", "TDMIN_B OUT",
+ "MICL", "Mic Jack",
+ "Headphones", "HPOL",
+ "Headphones", "HPOR",
+ "Speaker Amplifier INL", "HPOL",
+ "Speaker Amplifier INR", "HPOR",
+ "Internal Speakers", "Speaker Amplifier OUTL",
+ "Internal Speakers", "Speaker Amplifier OUTR";
+
+ assigned-clocks = <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+ status = "okay";
+
+ dai-link-0 {
+ sound-dai = <&frddr_a>;
+ };
+
+ dai-link-1 {
+ sound-dai = <&toddr_a>;
+ };
+
+ dai-link-2 {
+ sound-dai = <&tdmif_b>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ mclk-fs = <256>;
+
+ codec-0 {
+ sound-dai = <&rk817>;
+ };
+ };
+ };
+
+ speaker_amp: speaker-amplifier {
+ compatible = "simple-audio-amplifier";
+ sound-name-prefix = "Speaker Amplifier";
+ VCC-supply = <&hp_5v>;
+ };
+};
+
+&arb {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu100 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu101 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu102 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu103 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+/* RK817 only supports 12.5mV steps, round up the values */
+&cpu_opp_table_0 {
+ opp-1000000000 {
+ opp-microvolt = <737500>;
+ };
+ opp-1200000000 {
+ opp-microvolt = <737500>;
+ };
+ opp-1398000000 {
+ opp-microvolt = <762500>;
+ };
+ opp-1512000000 {
+ opp-microvolt = <800000>;
+ };
+ opp-1608000000 {
+ opp-microvolt = <837500>;
+ };
+ opp-1704000000 {
+ opp-microvolt = <862500>;
+ };
+ opp-1896000000 {
+ opp-microvolt = <987500>;
+ };
+ opp-1992000000 {
+ opp-microvolt = <1012500>;
+ };
+};
+
+/* RK818 only supports 12.5mV steps, round up the values */
+&cpub_opp_table_1 {
+ opp-1000000000 {
+ opp-microvolt = <775000>;
+ };
+ opp-1200000000 {
+ opp-microvolt = <775000>;
+ };
+ opp-1398000000 {
+ opp-microvolt = <800000>;
+ };
+ opp-1512000000 {
+ opp-microvolt = <825000>;
+ };
+ opp-1608000000 {
+ opp-microvolt = <862500>;
+ };
+ opp-1704000000 {
+ opp-microvolt = <900000>;
+ };
+ opp-1800000000 {
+ opp-microvolt = <987500>;
+ };
+ opp-1908000000 {
+ opp-microvolt = <1025000>;
+ };
+};
+
+&i2c_AO {
+ status = "okay";
+ pinctrl-0 = <&i2c_ao_sck_pins>, <&i2c_ao_sda_pins>;
+ pinctrl-names = "default";
+
+ rk818: pmic at 1c {
+ compatible = "rockchip,rk818";
+ reg = <0x1c>;
+ interrupt-parent = <&gpio_intc>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>; /* GPIOAO_7 */
+
+ vcc1-supply = <&vdd_sys>;
+ vcc2-supply = <&vdd_sys>;
+ vcc3-supply = <&vdd_sys>;
+ vcc4-supply = <&vdd_sys>;
+ vcc6-supply = <&vdd_sys>;
+ vcc7-supply = <&vcc_2v3>;
+ vcc8-supply = <&vcc_2v3>;
+ vcc9-supply = <&vddao_3v3>;
+ boost-supply = <&vdd_sys>;
+ switch-supply = <&vdd_sys>;
+
+ regulators {
+ vddcpu_a: DCDC_REG1 {
+ regulator-name = "vddcpu_a";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <775000>;
+ regulator-max-microvolt = <1025000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <775000>;
+ };
+ };
+
+ vdd_ee: DCDC_REG2 {
+ regulator-name = "vdd_ee";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <875000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <875000>;
+ };
+ };
+
+ vddq_1v1: DCDC_REG3 {
+ regulator-name = "vddq_1v1";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vddao_3v3: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vddao_3v3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ hp_5v: DCDC_BOOST {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "hp_5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vddio_ao1v8: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vddio_ao1v8";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vddq_1v8: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vddq_1v8";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vddio_c: LDO_REG9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vddio_c";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_sd: SWITCH_REG {
+ regulator-name = "vcc_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ OTG_SWITCH {
+ regulator-name = "otg_switch";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2c3 {
+ status = "okay";
+ pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
+ pinctrl-names = "default";
+
+ rk817: pmic at 20 {
+ compatible = "rockchip,rk817";
+ reg = <0x20>;
+ status = "okay";
+ interrupt-parent = <&gpio_intc>;
+
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>; /* GPIOAO_5 */
+
+ vcc1-supply = <&vdd_sys>;
+ vcc2-supply = <&vdd_sys>;
+ vcc3-supply = <&vdd_sys>;
+ vcc4-supply = <&vdd_sys>;
+ vcc5-supply = <&vdd_sys>;
+ vcc6-supply = <&vdd_sys>;
+ vcc7-supply = <&vdd_sys>;
+ vcc8-supply = <&vdd_sys>;
+ vcc9-supply = <&rk817_boost>;
+
+ #sound-dai-cells = <0>;
+ clocks = <&codec_clk>;
+ clock-names = "mclk";
+
+ #clock-cells = <1>;
+
+ regulators {
+ vddcpu_b: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <737500>;
+ regulator-max-microvolt = <1012500>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vddcpu_b";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_2v3: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2300000>;
+ regulator-max-microvolt = <2400000>;
+ regulator-initial-mode = <0x2>;
+ regulator-name = "vcc_2v3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vdd_codec";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_lcd: LDO_REG8 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_lcd";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk817_boost: BOOST {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5400000>;
+ regulator-name = "rk817_boost";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ usb_host: OTG_SWITCH {
+ regulator-name = "usb_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&clkc_audio {
+ status = "okay";
+};
+
+ð_phy {
+ status = "disabled";
+};
+
+&frddr_a {
+ status = "okay";
+};
+
+&periphs_pinctrl {
+ keypad_gpio_pins: keypad-gpio {
+ mux {
+ groups = "GPIOX_0", "GPIOX_1", "GPIOX_2", "GPIOX_3",
+ "GPIOX_4", "GPIOX_5", "GPIOX_6", "GPIOX_7",
+ "GPIOX_8", "GPIOX_9", "GPIOX_10", "GPIOX_11",
+ "GPIOX_12", "GPIOX_13", "GPIOX_14", "GPIOX_15",
+ "GPIOX_16", "GPIOX_17", "GPIOX_18", "GPIOX_19";
+ function = "gpio_periphs";
+ bias-pull-up;
+ output-disable;
+ };
+ };
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddio_ao1v8>;
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_c_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vddio_c>;
+
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vddio_ao1v8>;
+};
+
+
+&tdmif_b {
+ pinctrl-0 = <&tdm_b_dout0_pins>, <&tdm_b_fs_pins>, <&tdm_b_sclk_pins>, <&tdm_b_din1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ assigned-clocks = <&clkc_audio AUD_CLKID_TDM_SCLK_PAD1>,
+ <&clkc_audio AUD_CLKID_TDM_LRCLK_PAD1>;
+ assigned-clock-parents = <&clkc_audio AUD_CLKID_MST_B_SCLK>,
+ <&clkc_audio AUD_CLKID_MST_B_LRCLK>;
+ assigned-clock-rates = <0>, <0>;
+};
+
+&tdmin_b {
+ status = "okay";
+};
+
+&tdmout_b {
+ status = "okay";
+};
+
+&toddr_a {
+ status = "okay";
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+ dr_mode = "peripheral";
+};
+
+&usb2_phy0 {
+ status = "okay";
+};
+
+&usb2_phy1 {
+ status = "okay";
+ phy-supply = <&usb_host>;
+};
--
b4 0.10.1
More information about the linux-amlogic
mailing list