[PATCH v2 1/2] spi: dt-bindings: amlogic, meson-gx-spicc: Add pinctrl names for SPI signal states
Amjad Ouled-Ameur
aouledameur at baylibre.com
Thu Oct 6 03:57:52 PDT 2022
Hi Krzysztof,
Thank you for the review.
On 10/5/22 10:14, Krzysztof Kozlowski wrote:
> On 04/10/2022 13:10, Amjad Ouled-Ameur wrote:
>> SPI pins of the SPICC Controller in Meson-GX needs to be controlled by
>> pin biais when idle. Therefore define three pinctrl names:
>> - default: SPI pins are controlled by spi function.
>> - idle-high: SCLK pin is pulled-up, but MOSI/MISO are still controlled
>> by spi function.
>> - idle-low: SCLK pin is pulled-down, but MOSI/MISO are still controlled
>> by spi function.
>>
>> Reported-by: Da Xue <da at libre.computer>
>> Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
>> Signed-off-by: Amjad Ouled-Ameur <aouledameur at baylibre.com>
>> ---
>> .../devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml | 15 +++++++++++++++
>> 1 file changed, 15 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml b/Documentation/devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml
>> index 0c10f7678178..53013e27f507 100644
>> --- a/Documentation/devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml
>> +++ b/Documentation/devicetree/bindings/spi/amlogic,meson-gx-spicc.yaml
>> @@ -43,6 +43,14 @@ properties:
>> minItems: 1
>> maxItems: 2
>>
>> + pinctrl-0:
>> + minItems: 1
> maxItems?
>
Will fill it in next version.
>> +
>> + pinctrl-1:
>> + maxItems: 1
>> +
>> + pinctrl-names: true
> Why do you need all these in the bindings?
SPI clock bias needs to change at runtime depending on SPI mode, here is an example of
how this is supposed to be used ("spi_idle_low_pins" and "spi_idle_low_pins" are defined
in the second patch of this series):
&spicc {
pinctrl-0 = <&spi_pins>;
pinctrl-1 = <&spi_pins>, <&spi_idle_high_pins>;
pinctrl-2 = <&spi_pins>, <&spi_idle_low_pins>;
pinctrl-names = "default", "idle-high", "idle-low";
[...]
};
>> +
>> if:
>> properties:
>> compatible:
>> @@ -69,6 +77,13 @@ else:
>> items:
>> - const: core
>>
>> + pinctrl-names:
>> + minItems: 1
>> + items:
>> + - const: default
>> + - const: idle-high
>> + - const: idle-low
> This does not match what you wrote in the bindings - you mentioned only
> two set of pin controls.
Right, there are actually three set of pin controls, will correct the bindings above.
Regards,
Amjad
>
> Best regards,
> Krzysztof
>
More information about the linux-amlogic
mailing list