[PATCH net] net: phy: meson-gxl: fix interrupt handling in forced mode

Vyacheslav adeep at lexina.in
Fri Mar 4 11:52:48 PST 2022


Seems works for JetHub H1 (S905W with internal phy)

03.03.2022 10:54, Heiner Kallweit wrote:
> This PHY doesn't support a link-up interrupt source. If aneg is enabled
> we use the "aneg complete" interrupt for this purpose, but if aneg is
> disabled link-up isn't signaled currently.
> According to a vendor driver there's an additional "energy detect"
> interrupt source that can be used to signal link-up if aneg is disabled.
> We can safely ignore this interrupt source if aneg is enabled.
> 
> This patch was tested on a TX3 Mini TV box with S905W (even though
> boot message says it's a S905D).
> 
> This issue has been existing longer, but due to changes in phylib and
> the driver the patch applies only from the commit marked as fixed.
> 
> Fixes: 84c8f773d2dc ("net: phy: meson-gxl: remove the use of .ack_callback()")
> Signed-off-by: Heiner Kallweit <hkallweit1 at gmail.com>
> ---
>   drivers/net/phy/meson-gxl.c | 23 +++++++++++++----------
>   1 file changed, 13 insertions(+), 10 deletions(-)
> 
> diff --git a/drivers/net/phy/meson-gxl.c b/drivers/net/phy/meson-gxl.c
> index 7e7904fee..c49062ad7 100644
> --- a/drivers/net/phy/meson-gxl.c
> +++ b/drivers/net/phy/meson-gxl.c
> @@ -30,8 +30,12 @@
>   #define  INTSRC_LINK_DOWN	BIT(4)
>   #define  INTSRC_REMOTE_FAULT	BIT(5)
>   #define  INTSRC_ANEG_COMPLETE	BIT(6)
> +#define  INTSRC_ENERGY_DETECT	BIT(7)
>   #define INTSRC_MASK	30
>   
> +#define INT_SOURCES (INTSRC_LINK_DOWN | INTSRC_ANEG_COMPLETE | \
> +		     INTSRC_ENERGY_DETECT)
> +
>   #define BANK_ANALOG_DSP		0
>   #define BANK_WOL		1
>   #define BANK_BIST		3
> @@ -200,7 +204,6 @@ static int meson_gxl_ack_interrupt(struct phy_device *phydev)
>   
>   static int meson_gxl_config_intr(struct phy_device *phydev)
>   {
> -	u16 val;
>   	int ret;
>   
>   	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
> @@ -209,16 +212,9 @@ static int meson_gxl_config_intr(struct phy_device *phydev)
>   		if (ret)
>   			return ret;
>   
> -		val = INTSRC_ANEG_PR
> -			| INTSRC_PARALLEL_FAULT
> -			| INTSRC_ANEG_LP_ACK
> -			| INTSRC_LINK_DOWN
> -			| INTSRC_REMOTE_FAULT
> -			| INTSRC_ANEG_COMPLETE;
> -		ret = phy_write(phydev, INTSRC_MASK, val);
> +		ret = phy_write(phydev, INTSRC_MASK, INT_SOURCES);
>   	} else {
> -		val = 0;
> -		ret = phy_write(phydev, INTSRC_MASK, val);
> +		ret = phy_write(phydev, INTSRC_MASK, 0);
>   
>   		/* Ack any pending IRQ */
>   		ret = meson_gxl_ack_interrupt(phydev);
> @@ -237,9 +233,16 @@ static irqreturn_t meson_gxl_handle_interrupt(struct phy_device *phydev)
>   		return IRQ_NONE;
>   	}
>   
> +	irq_status &= INT_SOURCES;
> +
>   	if (irq_status == 0)
>   		return IRQ_NONE;
>   
> +	/* Aneg-complete interrupt is used for link-up detection */
> +	if (phydev->autoneg == AUTONEG_ENABLE &&
> +	    irq_status == INTSRC_ENERGY_DETECT)
> +		return IRQ_HANDLED;
> +
>   	phy_trigger_machine(phydev);
>   
>   	return IRQ_HANDLED;

-- 
Vyacheslav Bocharov



More information about the linux-amlogic mailing list