[PATCH V2 0/3] Add S4 SoC clock controller driver

Yu Tu yu.tu at amlogic.com
Thu Jul 28 01:55:41 PDT 2022


Hi Jerome,
	Thanks for your reply and explanation.

On 2022/7/28 16:27, Jerome Brunet wrote:
> [ EXTERNAL EMAIL ]
> 
> 
> On Thu 28 Jul 2022 at 16:06, Yu Tu <yu.tu at amlogic.com> wrote:
> 
>> Hi JB,
>>
>> On 2022/7/28 15:08, Jerome Brunet wrote:
>>> [ EXTERNAL EMAIL ]
>>>
>>> On Thu 28 Jul 2022 at 13:41, Yu Tu <yu.tu at amlogic.com> wrote:
>>>
>>>> 1. Add clock controller driver for S4 SOC.
>>>>
>>>> Yu Tu (3):
>>>>     dt-bindings: clk: meson: add S4 SoC clock controller bindings
>>>>     arm64: dts: meson: add S4 Soc clock controller in DT
>>>>     clk: meson: s4: add s4 SoC clock controller driver
>>>>
>>>> V1 -> V2: Change format as discussed in the email.
>>>>
>>>> Link:https://lore.kernel.org/linux-amlogic/20220708062757.3662-1-yu.tu@amlogic.com/
>>>>
>>>>    .../bindings/clock/amlogic,gxbb-clkc.txt      |    1 +
>>>>    MAINTAINERS                                   |    1 +
>>>>    arch/arm64/boot/dts/amlogic/meson-s4.dtsi     |   11 +
>>>>    drivers/clk/meson/Kconfig                     |   15 +
>>>>    drivers/clk/meson/Makefile                    |    1 +
>>>>    drivers/clk/meson/s4.c                        | 4732 +++++++++++++++++
>>>>    drivers/clk/meson/s4.h                        |  296 ++
>>>>    include/dt-bindings/clock/s4-clkc.h           |  146 +
>>>>    8 files changed, 5203 insertions(+)
>>>>    create mode 100644 drivers/clk/meson/s4.c
>>>>    create mode 100644 drivers/clk/meson/s4.h
>>>>    create mode 100644 include/dt-bindings/clock/s4-clkc.h
>>>>
>>>>
>>>> base-commit: b293bc9286ee21824e93f0fcfed3b78fdfee01e6
>>> Please don't post until you have addressed *ALL* the comments from the
>>> previous version.
>> The last email asked you to adopt A1 method, but you did not reply?
>>
>>> At first glance, I can see that this is still a single driver for
>>> what is obviously 2 controllers with 2 register spaces. Simple comments
>>> like the "<< 2" in the register declaration have not been addressed either.
>> I understand that this should be a controller, just two address
>> descriptions. One is the various PLL registers and one is the clock for
>> the peripherals. And PLL is to provide a clock source for various
>> peripheral clocks. So a clock controller is reasonable. I think you got
>> it wrong.
> 
> I don't think I do. This looks exactly like the A1.
> The post of that controller are still in the  archive and I am sure your
> colleagues can give you the history.
> 
> You clearly have register regions providing clock, separated by
> 0x8000. Claiming that as one big region is bad design.
> 
> There has been several remarks about using a big syscon on V1,
> unaddressed too.
> 
> CCF has everything necessary in place to handle each register region
> separately, properly and pass clock around.
> 
> You can handle it as a single controller, claiming the two regions
> individually but:
> # 1 - handling 2 different regmaps in the controller is going to be
>        bigger mess than you think
> # 2 - I am far from convinced there is any reason to do so
> 
It makes sense, as you say, to separate the two controllers. But I think 
the only thing that was forced apart was that the digital designers 
didn't put these registers together when they were designing the chips.

I'm going to separate the two controllers like you said.

> 
>>
>> Ok, if you insist on using two clock controllers,, please provide your the
>> reason and example code?
>>
>>> Seeing that, I have not reviewed this version further.
>>> I won't until all the comments from v1 are either addressed or answer
>>> Regards
>>> Jerome
>>> .
> 
> .



More information about the linux-amlogic mailing list