[PATCH v4 3/4] arm64: dts: meson: Add DDR PMU node

Krzysztof Kozlowski krzysztof.kozlowski at linaro.org
Fri Aug 5 01:22:38 PDT 2022


On 05/08/2022 09:14, Jiucheng Xu wrote:
> Add DDR PMU device node for G12 series SoC
> 
> Signed-off-by: Jiucheng Xu <jiucheng.xu at amlogic.com>
> ---
> Changes v3 -> v4:
>   - No change
> 
> Changes v2 -> v3:
>   - No change
> 
> Changes v1 -> v2:
>   - Remove model, dmc_nr, chann_nr properties
>   - Add g12a-ddr-pmu, g12b-ddr-pmu, sm1-ddr-pmu compatibles as
>     identifier
> ---
>  arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi | 7 +++++++
>  arch/arm64/boot/dts/amlogic/meson-g12a.dtsi       | 4 ++++
>  arch/arm64/boot/dts/amlogic/meson-g12b.dtsi       | 4 ++++
>  arch/arm64/boot/dts/amlogic/meson-sm1.dtsi        | 4 ++++
>  4 files changed, 19 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
> index 45947c1031c4..7e556fe575be 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
> @@ -2146,6 +2146,13 @@ hdmi_tx_out: endpoint {
>  			};
>  		};
>  
> +		ddr_pmu: ddr_pmu at ff638000 {

No underscores in node names.

Node names should be generic, so pmu.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation

> +			compatible = "amlogic,g12-ddr-pmu";
> +			reg = <0x0 0xff638000 0x0 0x100
> +			       0x0 0xff638c00 0x0 0x100>;
> +			interrupts = <GIC_SPI 52 IRQ_TYPE_EDGE_RISING>;
> +		};
> +
>  		gic: interrupt-controller at ffc01000 {
>  			compatible = "arm,gic-400";
>  			reg = <0x0 0xffc01000 0 0x1000>,
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
> index fb0ab27d1f64..4a32e081e70e 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
> @@ -133,3 +133,7 @@ map1 {
>  		};
>  	};
>  };
> +
> +&ddr_pmu {
> +	compatible = "amlogic,g12a-ddr-pmu";
> +};

Adding nodes at the end causes conflicts. They should be added in some
order...

Best regards,
Krzysztof



More information about the linux-amlogic mailing list