[PATCH v2 net-next] net: mdio: Fix spelling mistakes

Zheng Yongjun zhengyongjun3 at huawei.com
Tue Jun 1 18:51:51 PDT 2021


informations  ==> information
typicaly  ==> typically
derrive  ==> derive
eventhough  ==> even though
hz ==> Hz

Signed-off-by: Zheng Yongjun <zhengyongjun3 at huawei.com>
---
 drivers/net/mdio/mdio-bcm-unimac.c     | 2 +-
 drivers/net/mdio/mdio-mux-bcm-iproc.c  | 2 +-
 drivers/net/mdio/mdio-mux-meson-g12a.c | 2 +-
 drivers/net/mdio/of_mdio.c             | 2 +-
 4 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/net/mdio/mdio-bcm-unimac.c b/drivers/net/mdio/mdio-bcm-unimac.c
index 5d171e7f118d..63348716b426 100644
--- a/drivers/net/mdio/mdio-bcm-unimac.c
+++ b/drivers/net/mdio/mdio-bcm-unimac.c
@@ -203,7 +203,7 @@ static void unimac_mdio_clk_set(struct unimac_mdio_priv *priv)
 		return;
 	}
 
-	/* The MDIO clock is the reference clock (typicaly 250Mhz) divided by
+	/* The MDIO clock is the reference clock (typically 250MHz) divided by
 	 * 2 x (MDIO_CLK_DIV + 1)
 	 */
 	reg = unimac_mdio_readl(priv, MDIO_CFG);
diff --git a/drivers/net/mdio/mdio-mux-bcm-iproc.c b/drivers/net/mdio/mdio-mux-bcm-iproc.c
index 03261e6b9ceb..239e88c7a272 100644
--- a/drivers/net/mdio/mdio-mux-bcm-iproc.c
+++ b/drivers/net/mdio/mdio-mux-bcm-iproc.c
@@ -65,7 +65,7 @@ static void mdio_mux_iproc_config(struct iproc_mdiomux_desc *md)
 	writel(val, md->base + MDIO_SCAN_CTRL_OFFSET);
 
 	if (md->core_clk) {
-		/* use rate adjust regs to derrive the mdio's operating
+		/* use rate adjust regs to derive the mdio's operating
 		 * frequency from the specified core clock
 		 */
 		divisor = clk_get_rate(md->core_clk) / MDIO_OPERATING_FREQUENCY;
diff --git a/drivers/net/mdio/mdio-mux-meson-g12a.c b/drivers/net/mdio/mdio-mux-meson-g12a.c
index bf86c9c7a288..b8866bc3f2e8 100644
--- a/drivers/net/mdio/mdio-mux-meson-g12a.c
+++ b/drivers/net/mdio/mdio-mux-meson-g12a.c
@@ -95,7 +95,7 @@ static int g12a_ephy_pll_enable(struct clk_hw *hw)
 
 	/* Poll on the digital lock instead of the usual analog lock
 	 * This is done because bit 31 is unreliable on some SoC. Bit
-	 * 31 may indicate that the PLL is not lock eventhough the clock
+	 * 31 may indicate that the PLL is not lock even though the clock
 	 * is actually running
 	 */
 	return readl_poll_timeout(pll->base + ETH_PLL_CTL0, val,
diff --git a/drivers/net/mdio/of_mdio.c b/drivers/net/mdio/of_mdio.c
index 094494a68ddf..8e97d5b825f5 100644
--- a/drivers/net/mdio/of_mdio.c
+++ b/drivers/net/mdio/of_mdio.c
@@ -466,7 +466,7 @@ EXPORT_SYMBOL(of_phy_get_and_connect);
  * of_phy_is_fixed_link() and of_phy_register_fixed_link() must
  * support two DT bindings:
  * - the old DT binding, where 'fixed-link' was a property with 5
- *   cells encoding various informations about the fixed PHY
+ *   cells encoding various information about the fixed PHY
  * - the new DT binding, where 'fixed-link' is a sub-node of the
  *   Ethernet device.
  */
-- 
2.25.1




More information about the linux-amlogic mailing list