brcmfmac and unaligned sdio access on Khadas VIM3L

[Neil Armstrong]

Hi,

On 09/02/2021 13:48, Marek Szyprowski wrote:
> Hi
> 
> I've noticed that the Broadcom Wifi chip performs unaligned SDIO access 
> during the station scan on Khadas VIM3l board. This issue went unnoticed 
> so far, because there was a workaround in the meson MMC driver, which 
> has been recently disabled by commit e085b51c74cc ("mmc: meson-gx: check 
> for scatterlist size alignment in block mode") from current linux-next.
> 
> I can easily reproduce this issue with the following commands:
> 
> # dmesg | grep brcm
> [   11.659351] Bluetooth: hci0: BCM4359C0 'brcm/BCM4359C0.hcd' Patch
> [   13.079767] brcmfmac: brcmf_fw_alloc_request: using 
> brcm/brcmfmac4359-sdio for chip BCM4359/9
> [   13.527363] brcmfmac: brcmf_fw_alloc_request: using 
> brcm/brcmfmac4359-sdio for chip BCM4359/9
> [   13.601269] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available 
> (err=-11), device may have limited channels available
> [   13.619414] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4359/9 wl0: 
> Mar  6 2017 10:16:06 version 9.87.51.7 (r686312) FWID 01-4dcc75d9
> # ifconfig wlan0 up
> [  208.052058] ieee80211 phy0: brcmf_dongle_roam: WLC_SET_ROAM_TRIGGER 
> error (-52)
> # iw wlan0 scan >/dev/null
> [  218.148345] ------------[ cut here ]------------
> [  218.148501] unaligned sg len 504 blksize 256
> [  218.153712] WARNING: CPU: 1 PID: 75 at 
> drivers/mmc/host/meson-gx-mmc.c:251 
> meson_mmc_get_transfer_mode.isra.10+0xf8/0x130
> [  218.162616] Modules linked in: ipv6 brcmfmac brcmutil cfg80211 
> dw_hdmi_cec dw_hdmi_i2s_audio hci_uart btqca btbcm bluetooth 
> ecdh_generic ecc crct10dif_ce rfkill panfrost 
> snd_soc_meson_axg_sound_card snd_soc_meson_card_utils gpu_sched 
> meson_gxbb_wdt rtc_hym8563 pwm_meson meson_gxl rtc_meson_vrtc rc_khadas 
> meson_ir reset_meson_audio_arb realtek snd_soc_meson_g12a_tohdmitx 
> snd_soc_meson_codec_glue snd_soc_meson_axg_tdmout 
> snd_soc_meson_axg_frddr snd_soc_meson_axg_fifo axg_audio sclk_div 
> clk_phase mdio_mux_meson_g12a meson_dw_hdmi meson_drm meson_rng 
> dwmac_generic snd_soc_meson_axg_tdm_interface meson_canvas rng_core 
> dw_hdmi snd_soc_meson_axg_tdm_formatter dwmac_meson8b stmmac_platform 
> stmmac display_connector adc_keys pcs_xpcs nvmem_meson_efuse
> [  218.228329] CPU: 1 PID: 75 Comm: kworker/u8:2 Not tainted 
> 5.11.0-rc6-next-20210208 #2492
> [  218.236343] Hardware name: Khadas VIM3L (DT)
> [  218.240579] Workqueue: brcmf_wq/mmc2:0001:1 brcmf_sdio_dataworker 
> [brcmfmac]
> [  218.247559] pstate: 60400009 (nZCv daif +PAN -UAO -TCO BTYPE=--)
> [  218.253506] pc : meson_mmc_get_transfer_mode.isra.10+0xf8/0x130
> [  218.259372] lr : meson_mmc_get_transfer_mode.isra.10+0xf8/0x130
> [  218.265237] sp : ffff80001327b870
> [  218.268514] x29: ffff80001327b870 x28: 0000000000000003
> [  218.273776] x27: 0000000000000218 x26: 0000000000000600
> [  218.279036] x25: ffff000003a17678 x24: 0000000000000000
> [  218.284296] x23: ffff8000121cfae8 x22: ffff800011b54000
> [  218.289559] x21: ffff80001327bb18 x20: ffff00000277d000
> [  218.294819] x19: ffff80001327ba40 x18: 00000002faf07f80
> [  218.300081] x17: 0000000000004000 x16: 0000000000000000
> [  218.305341] x15: 0000000000000380 x14: 0000000000000000
> [  218.310603] x13: 0000000000000080 x12: 0000000000000000
> [  218.315865] x11: 0000000000000000 x10: 0000000000001370
> [  218.321125] x9 : ffff00006f995258 x8 : 000000009e0e7ca7
> [  218.326387] x7 : ffff80001327b4a0 x6 : 0000000000000001
> [  218.331648] x5 : 0000000000000001 x4 : 0000000000000000
> [  218.336912] x3 : 0000000000000002 x2 : ffff8000121f4768
> [  218.342171] x1 : 42fe1bd05e5eaa00 x0 : 0000000000000000
> [  218.347435] Call trace:
> [  218.349854]  meson_mmc_get_transfer_mode.isra.10+0xf8/0x130
> [  218.355368]  meson_mmc_request+0x74/0xb0
> [  218.359250]  __mmc_start_request+0xa4/0x2b0
> [  218.363390]  mmc_start_request+0x80/0xa8
> [  218.367272]  mmc_wait_for_req+0x68/0xd8
> [  218.371066]  mmc_submit_one.isra.17+0x78/0x148 [brcmfmac]
> [  218.376416]  brcmf_sdiod_sglist_rw+0x324/0x4a8 [brcmfmac]
> [  218.381762]  brcmf_sdiod_recv_chain+0x70/0x140 [brcmfmac]
> [  218.387110]  brcmf_sdio_dataworker+0x614/0x17d0 [brcmfmac]
> [  218.392545]  process_one_work+0x2a8/0x728
> [  218.396510]  worker_thread+0x48/0x460
> [  218.400132]  kthread+0x134/0x160
> [  218.403323]  ret_from_fork+0x10/0x18
> [  218.406862] irq event stamp: 15834
> [  218.410222] hardirqs last  enabled at (15833): [<ffff800010f95804>] 
> _raw_spin_unlock_irq+0x3c/0x80
> [  218.419107] hardirqs last disabled at (15834): [<ffff800010f895ac>] 
> el1_dbg+0x24/0x50
> [  218.426869] softirqs last  enabled at (15828): [<ffff800010010508>] 
> _stext+0x508/0x638
> [  218.434717] softirqs last disabled at (15823): [<ffff8000100952ec>] 
> irq_exit+0x19c/0x1a8
> [  218.442739] ---[ end trace dfc38bb4458b4c37 ]---
> #
> 
> Surprisingly the same commands executed on the Khadas VIM3 board with 
> the same kernel don't trigger the warning.

This may be because the VIM3 (G12A & G12B) has a broken SDIO controller using
an internal SRAM as bounce buffer instead of the scatter/gather DMA, cf amlogic,dram-access-quirk.

> 
> Let me know if I can help debugging this issue.

Simply remove the WARN_ONCE()...

> 
> Best regards
> 

Thanks for the report,
Neil