[PATCH 3/3] tty: serial: meson: add UART driver compatible with S4 SoC on-chip
Yu Tu
yu.tu at amlogic.com
Mon Dec 20 23:16:34 PST 2021
The S4 SoC on-chip UART uses a 12M clock as the clock source for
calculating the baud rate of the UART. But previously, chips used 24M or
other clock sources. So add this change. The specific clock source is
determined by chip design.
Signed-off-by: Yu Tu <yu.tu at amlogic.com>
---
drivers/tty/serial/meson_uart.c | 62 +++++++++++++++++++++++++++++----
1 file changed, 55 insertions(+), 7 deletions(-)
diff --git a/drivers/tty/serial/meson_uart.c b/drivers/tty/serial/meson_uart.c
index 69450a461c48..557c24d954a2 100644
--- a/drivers/tty/serial/meson_uart.c
+++ b/drivers/tty/serial/meson_uart.c
@@ -19,6 +19,7 @@
#include <linux/serial_core.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
+#include <linux/of_device.h>
/* Register offsets */
#define AML_UART_WFIFO 0x00
@@ -68,6 +69,8 @@
#define AML_UART_BAUD_MASK 0x7fffff
#define AML_UART_BAUD_USE BIT(23)
#define AML_UART_BAUD_XTAL BIT(24)
+#define AML_UART_BAUD_XTAL_TICK BIT(26)
+#define AML_UART_BAUD_XTAL_DIV2 BIT(27)
#define AML_UART_PORT_NUM 12
#define AML_UART_PORT_OFFSET 6
@@ -80,6 +83,11 @@ static struct uart_driver meson_uart_driver;
static struct uart_port *meson_ports[AML_UART_PORT_NUM];
+struct meson_uart_data {
+ /*A clock source that calculates baud rates*/
+ unsigned int xtal_tick_en;
+};
+
static void meson_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
}
@@ -294,16 +302,29 @@ static int meson_uart_startup(struct uart_port *port)
static void meson_uart_change_speed(struct uart_port *port, unsigned long baud)
{
+ struct meson_uart_data *uart_data = port->private_data;
u32 val;
while (!meson_uart_tx_empty(port))
cpu_relax();
+ val = readl_relaxed(port->membase + AML_UART_REG5);
+ val &= ~AML_UART_BAUD_MASK;
+
if (port->uartclk == 24000000) {
- val = ((port->uartclk / 3) / baud) - 1;
- val |= AML_UART_BAUD_XTAL;
+ if (uart_data->xtal_tick_en) {
+ val = (port->uartclk / 2 + baud / 2) / baud - 1;
+ val |= (AML_UART_BAUD_XTAL | AML_UART_BAUD_XTAL_DIV2);
+ } else {
+ val = ((port->uartclk / 3) + baud / 2) / baud - 1;
+ val &= (~(AML_UART_BAUD_XTAL_TICK |
+ AML_UART_BAUD_XTAL_DIV2));
+ val |= AML_UART_BAUD_XTAL;
+ }
} else {
val = ((port->uartclk * 10 / (baud * 4) + 5) / 10) - 1;
+ val &= (~(AML_UART_BAUD_XTAL | AML_UART_BAUD_XTAL_TICK |
+ AML_UART_BAUD_XTAL_DIV2));
}
val |= AML_UART_BAUD_USE;
writel(val, port->membase + AML_UART_REG5);
@@ -714,6 +735,7 @@ static int meson_uart_probe(struct platform_device *pdev)
{
struct resource *res_mem, *res_irq;
struct uart_port *port;
+ struct meson_uart_data *uart_data;
int ret = 0;
int id = -1;
@@ -729,6 +751,10 @@ static int meson_uart_probe(struct platform_device *pdev)
}
}
+ uart_data = of_device_get_match_data(&pdev->dev);
+ if (!uart_data)
+ return -EINVAL;
+
if (pdev->id < 0 || pdev->id >= AML_UART_PORT_NUM)
return -EINVAL;
@@ -770,6 +796,7 @@ static int meson_uart_probe(struct platform_device *pdev)
port->x_char = 0;
port->ops = &meson_uart_ops;
port->fifosize = 64;
+ port->private_data = uart_data;
meson_ports[pdev->id] = port;
platform_set_drvdata(pdev, port);
@@ -798,14 +825,35 @@ static int meson_uart_remove(struct platform_device *pdev)
return 0;
}
+static const struct meson_uart_data meson_uart_data = {
+ .xtal_tick_en = 0,
+};
+
+static const struct meson_uart_data s4_meson_uart_data = {
+ .xtal_tick_en = 1,
+};
+
static const struct of_device_id meson_uart_dt_match[] = {
/* Legacy bindings, should be removed when no more used */
- { .compatible = "amlogic,meson-uart" },
+ { .compatible = "amlogic,meson-uart",
+ .data = &meson_uart_data
+ },
/* Stable bindings */
- { .compatible = "amlogic,meson6-uart" },
- { .compatible = "amlogic,meson8-uart" },
- { .compatible = "amlogic,meson8b-uart" },
- { .compatible = "amlogic,meson-gx-uart" },
+ { .compatible = "amlogic,meson6-uart",
+ .data = &meson_uart_data
+ },
+ { .compatible = "amlogic,meson8-uart",
+ .data = &meson_uart_data
+ },
+ { .compatible = "amlogic,meson8b-uart",
+ .data = &meson_uart_data
+ },
+ { .compatible = "amlogic,meson-gx-uart",
+ .data = &meson_uart_data
+ },
+ { .compatible = "amlogic,meson-s4-uart",
+ .data = &s4_meson_uart_data
+ },
{ /* sentinel */ },
};
MODULE_DEVICE_TABLE(of, meson_uart_dt_match);
--
2.33.1
More information about the linux-amlogic
mailing list