[PATCH v1 1/2] mmc: meson-mx-sdhc: Set MANUAL_STOP for multi-block SDIO commands

Martin Blumenstingl martin.blumenstingl at googlemail.com
Sun Dec 12 06:59:55 PST 2021


The vendor driver implements special handling for multi-block
SD_IO_RW_DIRECT and SD_IO_RW_EXTENDED commands. It sets the MANUAL_STOP
bit in the MESON_SDHC_MISC register for these commands. In All other
cases this bit is cleared.

This fixes SDIO wifi using the brcmfmac driver which reported the
following error without this change on a Netxeon S82 board using a
Meson8 (S802) SoC:
  brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
                          BCM43362/1
  brcmf_sdiod_ramrw: membytes transfer failed
  brcmf_sdio_download_code_file: error -110 on writing 219557 membytes
                                 at 0x00000000
  brcmf_sdio_download_firmware: dongle image file download failed

And with this change:
  brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
                          BCM43362/1
  brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may
                            have limited channels available
  brcmf_c_preinit_dcmds: Firmware: BCM43362/1 wl0: Apr 22 2013 14:50:00
                         version 5.90.195.89.6 FWID 01-b30a427d

Fixes: e4bf1b0970ef96 ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
---
 drivers/mmc/host/meson-mx-sdhc-mmc.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/drivers/mmc/host/meson-mx-sdhc-mmc.c b/drivers/mmc/host/meson-mx-sdhc-mmc.c
index 7cd9c0ec2fcf..a89190d479cf 100644
--- a/drivers/mmc/host/meson-mx-sdhc-mmc.c
+++ b/drivers/mmc/host/meson-mx-sdhc-mmc.c
@@ -135,6 +135,7 @@ static void meson_mx_sdhc_start_cmd(struct mmc_host *mmc,
 				    struct mmc_command *cmd)
 {
 	struct meson_mx_sdhc_host *host = mmc_priv(mmc);
+	bool manual_stop = false;
 	u32 ictl, send;
 	int pack_len;
 
@@ -172,12 +173,20 @@ static void meson_mx_sdhc_start_cmd(struct mmc_host *mmc,
 		else
 			/* software flush: */
 			ictl |= MESON_SDHC_ICTL_DATA_XFER_OK;
+
+		manual_stop = cmd->data->blocks > 1 &&
+			      (cmd->opcode == SD_IO_RW_DIRECT ||
+			       cmd->opcode == SD_IO_RW_EXTENDED);
 	} else {
 		pack_len = 0;
 
 		ictl |= MESON_SDHC_ICTL_RESP_OK;
 	}
 
+	regmap_update_bits(host->regmap, MESON_SDHC_MISC,
+			   MESON_SDHC_MISC_MANUAL_STOP,
+			   manual_stop ? MESON_SDHC_MISC_MANUAL_STOP : 0);
+
 	if (cmd->opcode == MMC_STOP_TRANSMISSION)
 		send |= MESON_SDHC_SEND_DATA_STOP;
 
-- 
2.34.1




More information about the linux-amlogic mailing list