[PATCH] drm/bridge: dw-mipi-dsi: permit configuring the escape clock rate

Neil Armstrong narmstrong at baylibre.com
Fri Sep 11 09:02:32 EDT 2020


On 11/09/2020 10:29, Philippe CORNU wrote:
> 
> 
> On 9/4/20 2:55 PM, Neil Armstrong wrote:
>> The Amlogic D-PHY in the Amlogic AXG SoC Family does support a frequency
>> higher than 10MHz for the TX Escape Clock, thus make the target rate
>> configurable.
>>
>> Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
>> ---
>>   drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c | 25 +++++++++++++++----
>>   include/drm/bridge/dw_mipi_dsi.h              |  1 +
>>   2 files changed, 21 insertions(+), 5 deletions(-)
>>
>> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
>> index d580b2aa4ce9..31fc965c66fd 100644
>> --- a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
>> +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c
>> @@ -562,15 +562,30 @@ static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi)
>>   
>>   static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
>>   {
>> +	const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops;
>> +	unsigned int esc_rate; /* in MHz */
>> +	u32 esc_clk_division;
>> +	int ret;
>> +
>>   	/*
>>   	 * The maximum permitted escape clock is 20MHz and it is derived from
>> -	 * lanebyteclk, which is running at "lane_mbps / 8".  Thus we want:
>> -	 *
>> -	 *     (lane_mbps >> 3) / esc_clk_division < 20
>> +	 * lanebyteclk, which is running at "lane_mbps / 8".
>> +	 */
>> +	if (phy_ops->get_esc_clk_rate) {
>> +		ret = phy_ops->get_esc_clk_rate(dsi->plat_data->priv_data,
>> +						&esc_rate);
>> +		if (ret)
>> +			DRM_DEBUG_DRIVER("Phy get_esc_clk_rate() failed\n");
>> +	} else
>> +		esc_rate = 20; /* Default to 20MHz */
>> +
>> +	/*
>> +	 * We want :
>> +	 *     (lane_mbps >> 3) / esc_clk_division < X
>>   	 * which is:
>> -	 *     (lane_mbps >> 3) / 20 > esc_clk_division
>> +	 *     (lane_mbps >> 3) / X > esc_clk_division
>>   	 */
>> -	u32 esc_clk_division = (dsi->lane_mbps >> 3) / 20 + 1;
>> +	esc_clk_division = (dsi->lane_mbps >> 3) / esc_rate + 1;
>>   
>>   	dsi_write(dsi, DSI_PWR_UP, RESET);
>>   
>> diff --git a/include/drm/bridge/dw_mipi_dsi.h b/include/drm/bridge/dw_mipi_dsi.h
>> index b0e390b3288e..bda8aa7c2280 100644
>> --- a/include/drm/bridge/dw_mipi_dsi.h
>> +++ b/include/drm/bridge/dw_mipi_dsi.h
>> @@ -36,6 +36,7 @@ struct dw_mipi_dsi_phy_ops {
>>   			     unsigned int *lane_mbps);
>>   	int (*get_timing)(void *priv_data, unsigned int lane_mbps,
>>   			  struct dw_mipi_dsi_dphy_timing *timing);
>> +	int (*get_esc_clk_rate)(void *priv_data, unsigned int *esc_clk_rate);
>>   };
>>   
>>   struct dw_mipi_dsi_host_ops {
>>
> 
> Hi Neil,
> Thank you for the patch
> 
> Reviewed-by: Philippe Cornu <philippe.cornu at st.com>
> 
> Philippe :-)
> 

Thanks !

Applying to drm-misc-next

Neil



More information about the linux-amlogic mailing list