[PATCH 5/5] boards: amlogic: update documentation for Beelink GT-King/Pro
Neil Armstrong
narmstrong at baylibre.com
Fri Dec 18 04:47:01 EST 2020
On 18/12/2020 09:45, Christian Hewitt wrote:
> Update the device matrix and add build instructions.
>
> Signed-off-by: Christian Hewitt <christianshewitt at gmail.com>
> ---
> doc/board/amlogic/beelink-gtking.rst | 115 +++++++++++++++++++++++
> doc/board/amlogic/beelink-gtkingpro.rst | 116 ++++++++++++++++++++++++
> doc/board/amlogic/index.rst | 4 +-
> 3 files changed, 234 insertions(+), 1 deletion(-)
> create mode 100644 doc/board/amlogic/beelink-gtking.rst
> create mode 100644 doc/board/amlogic/beelink-gtkingpro.rst
>
> diff --git a/doc/board/amlogic/beelink-gtking.rst b/doc/board/amlogic/beelink-gtking.rst
> new file mode 100644
> index 0000000000..56ce2cb273
> --- /dev/null
> +++ b/doc/board/amlogic/beelink-gtking.rst
> @@ -0,0 +1,115 @@
> +.. SPDX-License-Identifier: GPL-2.0+
> +
> +U-Boot for Beelink GT-King
> +==========================
> +
> +The Shenzen AZW (Beelink) GT-King is based on the Amlogic W400 reference
> +board with an S922X-H chip.
> +
> +- 4GB LPDDR4 RAM
> +- 64GB eMMC storage
> +- 10/100/1000 Base-T Ethernet
> +- AP6356S Wireless (802.11 a/b/g/n/ac, BT 4.1)
> +- HDMI 2.1 video
> +- S/PDIF optical output
> +- Analogue audio output
> +- 1x USB 2.0 port
> +- 2x USB 3.0 ports
> +- IR receiver
> +- 1x micro SD card slot
> +
> +Beelink do not provide public schematics, but have been willing
> +to share them with known distro developers on request.
> +
> +U-Boot compilation
> +------------------
> +
> +.. code-block:: bash
> +
> + $ export CROSS_COMPILE=aarch64-none-elf-
> + $ make beelink-gtking_defconfig
> + $ make
> +
> +Image creation
> +--------------
> +
> +Amlogic does not provide sources for the firmware and for tools needed
> +to create the bootloader image. Beelink have provided the Amlogic "SDK"
> +in their forums, but the u-boot sources included result in 2GB RAM being
> +detected. The following FIPs were generated with newer private sources
> +and give correct (4GB) RAM detection:
> +
> +https://github.com/LibreELEC/amlogic-boot-fip/tree/master/beelink-s922x
> +
> +NB: Beelink use a common board config for GT-King, GT-King Pro and the
> +GS-King-X model, hence the "beelink-s922x" name.
> +
> +.. code-block:: bash
> +
> + $ wget https://github.com/LibreELEC/amlogic-boot-fip/archive/master.zip
> + $ unzip master.zip
> + $ export FIPDIR=$PWD/amlogic-boot-fip/beelink-s922x
> +
> +Go back to the mainline U-Boot source tree then:
> +
> +.. code-block:: bash
> +
> + $ mkdir fip
> + $ cp $FIPDIR/* fip/
> + $ cp u-boot.bin fip/bl33.bin
> +
> + $ sh fip/blx_fix.sh \
> + fip/bl30.bin \
> + fip/zero_tmp \
> + fip/bl30_zero.bin \
> + fip/bl301.bin \
> + fip/bl301_zero.bin \
> + fip/bl30_new.bin \
> + bl30
> +
> + $ sh fip/blx_fix.sh \
> + fip/bl2.bin \
> + fip/zero_tmp \
> + fip/bl2_zero.bin \
> + fip/acs.bin \
> + fip/bl21_zero.bin \
> + fip/bl2_new.bin \
> + bl2
> +
> + $ fip/aml_encrypt_g12b --bl30sig --input fip/bl30_new.bin \
> + --output fip/bl30_new.bin.g12a.enc \
> + --level v3
> + $ fip/aml_encrypt_g12b --bl3sig --input fip/bl30_new.bin.g12a.enc \
> + --output fip/bl30_new.bin.enc \
> + --level v3 --type bl30
> + $ fip/aml_encrypt_g12b --bl3sig --input fip/bl31.img \
> + --output fip/bl31.img.enc \
> + --level v3 --type bl31
> + $ fip/aml_encrypt_g12b --bl3sig --input fip/bl33.bin --compress lz4 \
> + --output fip/bl33.bin.enc \
> + --level v3 --type bl33
> + $ fip/aml_encrypt_g12b --bl2sig --input fip/bl2_new.bin \
> + --output fip/bl2.n.bin.sig
> + $ fip/aml_encrypt_g12b --bootmk \
> + --output fip/u-boot.bin \
> + --bl2 fip/bl2.n.bin.sig \
> + --bl30 fip/bl30_new.bin.enc \
> + --bl31 fip/bl31.img.enc \
> + --bl33 fip/bl33.bin.enc \
> + --ddrfw1 fip/ddr4_1d.fw \
> + --ddrfw2 fip/ddr4_2d.fw \
> + --ddrfw3 fip/ddr3_1d.fw \
> + --ddrfw4 fip/piei.fw \
> + --ddrfw5 fip/lpddr4_1d.fw \
> + --ddrfw6 fip/lpddr4_2d.fw \
> + --ddrfw7 fip/diag_lpddr4.fw \
> + --ddrfw8 fip/aml_ddr.fw \
> + --level v3
> +
> +and then write the image to SD with:
> +
> +.. code-block:: bash
> +
> + $ DEV=/dev/your_sd_device
> + $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
> + $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
> diff --git a/doc/board/amlogic/beelink-gtkingpro.rst b/doc/board/amlogic/beelink-gtkingpro.rst
> new file mode 100644
> index 0000000000..d750351361
> --- /dev/null
> +++ b/doc/board/amlogic/beelink-gtkingpro.rst
> @@ -0,0 +1,116 @@
> +.. SPDX-License-Identifier: GPL-2.0+
> +
> +U-Boot for Beelink GT-King Pro
> +==============================
> +
> +The Shenzen AZW (Beelink) GT-King Pro is based on the Amlogic W400 reference
> +board with an S922X-H chip.
> +
> +- 4GB LPDDR4 RAM
> +- 64GB eMMC storage
> +- 10/100/1000 Base-T Ethernet
> +- AP6356S Wireless (802.11 a/b/g/n/ac, BT 4.1)
> +- HDMI 2.1 video
> +- Analogue audio output
> +- 1x RS232 port
> +- 2x USB 2.0 port
> +- 2x USB 3.0 ports
> +- IR receiver
> +- 1x SD card slot
> +- 1x Power on/off button
> +
> +Beelink do not provide public schematics, but have been willing
> +to share them with known distro developers on request.
> +
> +U-Boot compilation
> +------------------
> +
> +.. code-block:: bash
> +
> + $ export CROSS_COMPILE=aarch64-none-elf-
> + $ make beelink-gtkingpro_defconfig
> + $ make
> +
> +Image creation
> +--------------
> +
> +Amlogic does not provide sources for the firmware and for tools needed
> +to create the bootloader image. Beelink have provided the Amlogic "SDK"
> +in their forums, but the u-boot sources included result in 2GB RAM being
> +detected. The following FIPs were generated with newer private sources
> +and give correct (4GB) RAM detection:
> +
> +https://github.com/LibreELEC/amlogic-boot-fip/tree/master/beelink-s922x
> +
> +NB: Beelink use a common board config for GT-King, GT-King Pro and the
> +GS-King-X model, hence the "beelink-s922x" name.
> +
> +.. code-block:: bash
> +
> + $ wget https://github.com/LibreELEC/amlogic-boot-fip/archive/master.zip
> + $ unzip master.zip
> + $ export FIPDIR=$PWD/amlogic-boot-fip/beelink-s922x
> +
> +Go back to the mainline U-Boot source tree then:
> +
> +.. code-block:: bash
> +
> + $ mkdir fip
> + $ cp $FIPDIR/* fip/
> + $ cp u-boot.bin fip/bl33.bin
> +
> + $ sh fip/blx_fix.sh \
> + fip/bl30.bin \
> + fip/zero_tmp \
> + fip/bl30_zero.bin \
> + fip/bl301.bin \
> + fip/bl301_zero.bin \
> + fip/bl30_new.bin \
> + bl30
> +
> + $ sh fip/blx_fix.sh \
> + fip/bl2.bin \
> + fip/zero_tmp \
> + fip/bl2_zero.bin \
> + fip/acs.bin \
> + fip/bl21_zero.bin \
> + fip/bl2_new.bin \
> + bl2
> +
> + $ fip/aml_encrypt_g12b --bl30sig --input fip/bl30_new.bin \
> + --output fip/bl30_new.bin.g12a.enc \
> + --level v3
> + $ fip/aml_encrypt_g12b --bl3sig --input fip/bl30_new.bin.g12a.enc \
> + --output fip/bl30_new.bin.enc \
> + --level v3 --type bl30
> + $ fip/aml_encrypt_g12b --bl3sig --input fip/bl31.img \
> + --output fip/bl31.img.enc \
> + --level v3 --type bl31
> + $ fip/aml_encrypt_g12b --bl3sig --input fip/bl33.bin --compress lz4 \
> + --output fip/bl33.bin.enc \
> + --level v3 --type bl33
> + $ fip/aml_encrypt_g12b --bl2sig --input fip/bl2_new.bin \
> + --output fip/bl2.n.bin.sig
> + $ fip/aml_encrypt_g12b --bootmk \
> + --output fip/u-boot.bin \
> + --bl2 fip/bl2.n.bin.sig \
> + --bl30 fip/bl30_new.bin.enc \
> + --bl31 fip/bl31.img.enc \
> + --bl33 fip/bl33.bin.enc \
> + --ddrfw1 fip/ddr4_1d.fw \
> + --ddrfw2 fip/ddr4_2d.fw \
> + --ddrfw3 fip/ddr3_1d.fw \
> + --ddrfw4 fip/piei.fw \
> + --ddrfw5 fip/lpddr4_1d.fw \
> + --ddrfw6 fip/lpddr4_2d.fw \
> + --ddrfw7 fip/diag_lpddr4.fw \
> + --ddrfw8 fip/aml_ddr.fw \
> + --level v3
> +
> +and then write the image to SD with:
> +
> +.. code-block:: bash
> +
> + $ DEV=/dev/your_sd_device
> + $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
> + $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
> diff --git a/doc/board/amlogic/index.rst b/doc/board/amlogic/index.rst
> index a585d857df..275c3664b7 100644
> --- a/doc/board/amlogic/index.rst
> +++ b/doc/board/amlogic/index.rst
> @@ -17,7 +17,7 @@ This matrix concerns the actual source code version.
> +===============================+===========+=================+==============+============+============+=============+==============+
> | Boards | Odroid-C2 | P212 | Khadas VIM2 | S400 | U200 | Odroid-N2 | SEI610 |
> | | Nanopi-K2 | Khadas-VIM | Libretech-PC | | SEI510 | Khadas-VIM3 | Khadas-VIM3L |
> -| | P200 | LibreTech-CC v1 | WeTek Core2 | | | | Odroid-C4 |
> +| | P200 | LibreTech-CC v1 | WeTek Core2 | | | GT-King/Pro | Odroid-C4 |
> | | P201 | LibreTech-AC v2 | | | | | |
> +-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
> | UART | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** |
> @@ -77,6 +77,8 @@ Board Documentation
> .. toctree::
> :maxdepth: 1
>
> + beelink-gtking
> + beelink-gtkingpro
> khadas-vim2
> khadas-vim3l
> khadas-vim3
>
Acked-by: Neil Armstrong <narmstrong at baylibre.com>
More information about the linux-amlogic
mailing list