[PATCH v3 2/5] arm64: dts: meson: fix PHY deassert timing requirements
Stefan Agner
stefan at agner.ch
Mon Dec 7 12:58:00 EST 2020
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. This fixes an issue seen on ODROID-C2 where the Ethernet
link doesn't come up when using ip link set down/up:
[ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down
[ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36)
[ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma
[ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed
Fixes: f29cabf240ed ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
Signed-off-by: Stefan Agner <stefan at agner.ch>
---
arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts | 2 +-
arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts | 2 +-
9 files changed, 9 insertions(+), 9 deletions(-)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
index 7be3e354093b..de27beafe9db 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts
@@ -165,7 +165,7 @@ eth_phy0: ethernet-phy at 0 {
reg = <0>;
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index 70fcfb7b0683..50de1d01e565 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -200,7 +200,7 @@ eth_phy0: ethernet-phy at 0 {
reg = <0>;
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
index 222ee8069cfa..9b0b81f191f1 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
@@ -126,7 +126,7 @@ eth_phy0: ethernet-phy at 0 {
reg = <0>;
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
index ad812854a107..a350fee1264d 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
@@ -147,7 +147,7 @@ eth_phy0: ethernet-phy at 0 {
reg = <0>;
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
index b08c4537f260..b2ab05c22090 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
@@ -82,7 +82,7 @@ external_phy: ethernet-phy at 0 {
/* External PHY reset is shared with internal PHY Led signal */
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts
index bff8ec2c1c70..e38d9e50caa7 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts
@@ -194,7 +194,7 @@ external_phy: ethernet-phy at 0 {
reg = <0>;
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
index 83eca3af44ce..dfa7a37a1281 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-nexbox-a1.dts
@@ -112,7 +112,7 @@ external_phy: ethernet-phy at 0 {
max-speed = <1000>;
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
};
};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts
index ea45ae0c71b7..8edbfe040805 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts
@@ -64,7 +64,7 @@ external_phy: ethernet-phy at 0 {
/* External PHY reset is shared with internal PHY Led signal */
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
interrupt-parent = <&gpio_intc>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts
index c89c9f846fb1..dde7cfe12cff 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts
@@ -114,7 +114,7 @@ external_phy: ethernet-phy at 0 {
max-speed = <1000>;
reset-assert-us = <10000>;
- reset-deassert-us = <30000>;
+ reset-deassert-us = <80000>;
reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
};
};
--
2.29.2
More information about the linux-amlogic
mailing list