[PATCH v3 1/2] arm64: dts: meson-g12b-odroid-n2: Enable RTC controller node
Anand Moon
linux.amoon at gmail.com
Wed Aug 26 02:59:04 EDT 2020
hi Jerome
On Tue, 25 Aug 2020 at 20:00, Jerome Brunet <jbrunet at baylibre.com> wrote:
>
>
> On Tue 25 Aug 2020 at 11:01, Anand Moon <linux.amoon at gmail.com> wrote:
>
> > Hi Jerome
> >
> > On Mon, 24 Aug 2020 at 20:00, Jerome Brunet <jbrunet at baylibre.com> wrote:
> >>
> >>
> >> On Mon 24 Aug 2020 at 15:50, Neil Armstrong <narmstrong at baylibre.com> wrote:
> >>
> >> > On 24/08/2020 15:41, Anand Moon wrote:
> >> >> hi All,
> >> >>
> >> >> On Fri, 21 Aug 2020 at 10:13, Anand Moon <linux.amoon at gmail.com> wrote:
> >> >>>
> >> >>> Hi Kevin,
> >> >>>
> >> >>> Thanks for your review comments.
> >> >>>
> >> >>> On Fri, 21 Aug 2020 at 01:03, Kevin Hilman <khilman at baylibre.com> wrote:
> >> >>>>
> >> >>>> Anand Moon <linux.amoon at gmail.com> writes:
> >> >>>>
> >> >>>>> Enable RTC PCF8563 node on Odroid-N2 SBC, In order to
> >> >>>>> support the RTC wakealarm feature for suspend and resume.
> >> >>>>> Also assign an alias to the pcf8563 to rtc0 and meson-vrtc to rtc1
> >> >>>>> timer device to prevent it being assigned to /dev/rtc0
> >> >>>>> which disto userspace tools assume is a clock device.
> >> >>>>>
> >> >>>>> Cc: Neil Armstrong <narmstrong at baylibre.com>
> >> >>>>> Cc: Kevin Hilman <khilman at baylibre.com>
> >> >>>>> Suggested-by: Christian Hewitt <christianshewitt at gmail.com>
> >> >>>>> Signed-off-by: Anand Moon <linux.amoon at gmail.com>
> >> >>>>> ---
> >> >>>>> Changes V3
> >> >>>>> --Drop the INI GPIOAO.BIT7 pinctrl.
> >> >>>>
> >> >>>> Why did you drop this GPIO? Isn't this the GPIO that the RTC uses to
> >> >>>> wakeup the system? If so, this should be included as part of this
> >> >>>> patch.
> >> >>>>
> >> >>>> It probably still works because the bootloader configures this GPIO as
> >> >>>> input, but the kernel should not rely on the booloader for that, so
> >> >>>> please include as part of this patch.
> >> >>>>
> >> >>>
> >> >>> Ok I will figure out the correct pinctrl need for this settings.
> >> >>> looking into the Odroid N2 schematics.
> >> >>>
> >> >>
> >> >> I am trying to map the RTC INT pinctrl, ie RTC INT GPIOAO.BIT7.
> >> >
> >> >
> >> > Simply add:
> >> >
> >> > interrupt-parent = <&gpio_intc>;
> >> > interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> >> >
> >> > to reflect the interrupt connection.
> >
> > I have tried this setting, but it is not working.
> >
> > [alarm at archl-on2e ~]$ dmesg| grep rtc
> > [ 5.378002] meson-vrtc ff8000a8.rtc: registered as rtc1
> > [ 5.942307] rtc-pcf8563 0-0051: pcf8563_write_block_data: err=-110
> > addr=0e, data=03
> > [ 5.942316] rtc-pcf8563 0-0051: pcf8563_probe: write error
> > [ 5.945983] rtc-pcf8563: probe of 0-0051 failed with error -5
> >
>
> -110 is timeout ... either you i2c bus is broken and you device is not
> at 0x51. In both case, it has nothing to do with the interrupt configuration
>
I have check the I2C bus on the device for rtc and it return correctly.
$ sudo i2cdetect -l
i2c-1 i2c DesignWare HDMI I2C adapter
i2c-0 i2c Meson I2C adapter I2C adapter
$
$ sudo i2cdetect -y -r 0
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- UU -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
> >
> >> >
> >> > No need to setup pinctrl here since the GPIO input is always connected
> >> > to the gpio irq generator whatever pinctrl mode is set.
> >>
> >> It is actually better to setup pinctrl. Yes the irq controller can work
> >> whatever the pin setup but if an output function is active it can mess with
> >> what the irq controller gets.
> >>
> >> Think about applying/removing bias if necessary too.
> >>
> >
> > Ok, I am trying to add a new pinctrl configuration for
> > TSIN_A_DIN0 // TDMB_FS // TDMB_SLV_FS
> > But it's still not working at my end.
>
> Either you are quite confused when it comes to pinctrl or I am.
Basically I dont want to keep repeating silly mistakes.
> TSIN and TDM have nothing to do with an i2c RTC.
Yes I understand this clearly, that's why I have dropped the
RTC INT gpio pinctrl settings.Without this setting RTC driver
works fine and their is no issue rtcwakeup during suspend
and resume in my testing.
-Anand
More information about the linux-amlogic
mailing list