[PATCH 3/3] clk: meson: clk-pll: always enable a critical PLL when setting the rate

Neil Armstrong narmstrong at baylibre.com
Fri Sep 20 01:06:58 PDT 2019


Hi Stephen,

On 19/09/2019 19:06, Stephen Boyd wrote:
> Quoting Jerome Brunet (2019-09-19 06:01:28)
>> On Thu 19 Sep 2019 at 11:38, Neil Armstrong <narmstrong at baylibre.com> wrote:
>>
>>> Make sure we always enable a PLL on a set_rate() when the PLL is
>>> flagged as critical.
>>>
>>> This fixes the case when the Amlogic G12A SYS_PLL gets disabled by the
>>> PSCI firmware when resuming from suspend-to-memory, in the case
>>> where the CPU was not clocked by the SYS_PLL, but by the fixed PLL
>>> fixed divisors.
>>> In this particular case, when changing the PLL rate, CCF doesn't handle
>>> the fact the PLL could have been disabled in the meantime and set_rate()
>>> only changes the rate and never enables it again.
>>>
>>> Fixes: d6e81845b7d9 ("clk: meson: clk-pll: check if the clock is already enabled')
>>> Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
>>> ---
>>>  drivers/clk/meson/clk-pll.c | 2 +-
>>>  1 file changed, 1 insertion(+), 1 deletion(-)
>>>
>>> diff --git a/drivers/clk/meson/clk-pll.c b/drivers/clk/meson/clk-pll.c
>>> index ddb1e5634739..8c5adccb7959 100644
>>> --- a/drivers/clk/meson/clk-pll.c
>>> +++ b/drivers/clk/meson/clk-pll.c
>>> @@ -379,7 +379,7 @@ static int meson_clk_pll_set_rate(struct clk_hw *hw, unsigned long rate,
>>>       }
>>>  
>>>       /* If the pll is stopped, bail out now */
>>> -     if (!enabled)
>>> +     if (!(hw->init->flags & CLK_IS_CRITICAL) && !enabled)
>>
>> This is surely a work around to the issue at hand but:
>>
>> * Enabling the clock, critical or not, should not be done but the
>> set_rate() callback. This is not the purpose of this callback.
>>
>> * Enabling the clock in such way does not walk the tree. So, if there is
>> ever another PSCI Fw which disable we would get into the same issue
>> again. IOW, This is not specific to the PLL driver so it should not have
>> to deal with this.
> 
> Exactly.
> 
>>
>> Since this clock can change out of CCF maybe it should be marked with
>> CLK_GET_RATE_NOCACHE ?
> 
> Yes, or figure out a way to make the clk state match what PSCI leaves it
> in on resume from suspend.
> 
> 
>>
>> When CCF hits a clock with CLK_GET_RATE_NOCACHE while walking the tree,
>> in addition to to calling get_rate(), CCF could also call is_enabled()
>> if the clock has CLK_IS_CRITICAL and possibly .enable() ?
> 
> This logic should go under a new flag. The CLK_GET_RATE_NOCACHE flag
> specifically means get rate shouldn't be a cached operation. It doesn't
> relate to the enable state. I hope that you can implement some sort of
> resume hook that synchronizes the state though so that you don't need to
> rely on clk_set_rate() or clk_get_rate() to trigger a sync.
> 

It's exactly the goal of [1] where I resync a clock tree after a resume.

But I don't check the enable state, would you mean that:
if core->ops->enable && core->enable_count > 0 && !clk_core_is_enabled(core)
    core->ops->enable(core->hw)

along the parent/rate resync ?

Isn't that dangerous ?

[1] https://patchwork.kernel.org/patch/11152101/

Neil



More information about the linux-amlogic mailing list