[PATCHv1 1/3] arm64: dts: meson: odroid-c2: Add missing regulator linked to P5V0 regulator

Anand Moon linux.amoon at gmail.com
Sun Sep 1 06:57:47 PDT 2019


Hi Martin,

Thanks for your review comments.

Their have been some revision changes in S905 Odroid Schematics.
[0] https://dn.odroid.com/S905/Schematic/

Well I have make my changes based on old odroid-c2_rev0.2_20151218.pdf

On Sun, 1 Sep 2019 at 17:07, Martin Blumenstingl
<martin.blumenstingl at googlemail.com> wrote:
>
> On Wed, Aug 28, 2019 at 10:27 PM Anand Moon <linux.amoon at gmail.com> wrote:
> >
> > As per shematics VDDIO_AO18, VDDIO_AO3V3/VDD3V3 DDR3_1V5/DDR_VDDC:
> typo: "schematics"
>
OK. next time will run spell check before I send these changes.

> > fixed regulator output which is supplied by P5V0.
> >
> > Rename vcc3v3 regulator node to vddio_ao3v3 as per shematics.
> typo: "schematics"
Ok.
>
> according to the schematics there's both:
> - VDDIO_AO3V3
> - VCC3V3 (which is turned on by VDDIO_AO3V3, see [0])
>

>From the schematics it seams same.

VDDIO_AO3V3---DMG340LSQN4 (Q4)---VCC3V3

But this name change was done to link TFLASH_VDD_EN to TFLASH_VDD for eMMC

VDDIO_AO3V3-----TFLASH_VDD using  TFLASH_VDD_EN gpio pin.

Well I have tested this changes on eMMC module.

> > Cc: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
> > Cc: Jerome Brunet <jbrunet at baylibre.com>
> > Cc: Neil Armstrong <narmstrong at baylibre.com>
> > Signed-off-by: Anand Moon <linux.amoon at gmail.com>
> > ---
> >  .../boot/dts/amlogic/meson-gxbb-odroidc2.dts  | 29 +++++++++++++++++--
> >  1 file changed, 26 insertions(+), 3 deletions(-)
> >
> > diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> > index 792698a60a12..98e742bf44c1 100644
> > --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> > +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> > @@ -104,11 +104,34 @@
> >                 regulator-max-microvolt = <1800000>;
> >         };
> >
> > -       vcc3v3: regulator-vcc3v3 {
> > +       vddio_ao1v8: regulator-vddio-ao1v8 {
> >                 compatible = "regulator-fixed";
> > -               regulator-name = "VCC3V3";
> > +               regulator-name = "VDDIO_AO1V8";
> > +               regulator-min-microvolt = <1800000>;
> > +               regulator-max-microvolt = <1800000>;
> > +               regulator-always-on;
> > +               /* U17 RT9179GB */
> > +               vin-supply = <&p5v0>;
> > +       };
> > +
> > +       vddio_ao3v3: regulator-vddio-ao3v3 {
> > +               compatible = "regulator-fixed";
> > +               regulator-name = "VDDIO_AO3V3";
> >                 regulator-min-microvolt = <3300000>;
> >                 regulator-max-microvolt = <3300000>;
> > +               regulator-always-on;
> > +               /* U11 MP2161GJ-C499 */
> > +               vin-supply = <&p5v0>;
> > +       };
> > +
> > +       vddc_ddr: regulator-vddc-ddr {
> > +               compatible = "regulator-fixed";
> > +               regulator-name = "DDR_VDDC";
> personally I would call this (along with the node name and alias) DDR3_1V5
> odroid-c2_rev0.1_20150930.pdf shows that DDR3_1V5 and DDR_VDDC are
> both the same. however, the DDR_VDDC signal name is not used by any
> component in the datasheet

Ok Thanks I will change this to DDR3_1V5 as per the datasheet.
>
> > +               regulator-min-microvolt = <1500000>;
> > +               regulator-max-microvolt = <1500000>;
> > +               regulator-always-on;
> > +               /* U15 MP2161GJ-C499 */
> > +               vin-supply = <&p5v0>;
> >         };
> >
> >         emmc_pwrseq: emmc-pwrseq {
> > @@ -301,7 +324,7 @@
> >         mmc-hs200-1_8v;
> >
> >         mmc-pwrseq = <&emmc_pwrseq>;
> > -       vmmc-supply = <&vcc3v3>;
> > +       vmmc-supply = <&vddio_ao3v3>;
> odroid-c2_rev0.1_20150930.pdf uses VCC3V3 as supply
>
>
> Martin

Best Regards

-Anand



More information about the linux-amlogic mailing list