dwc2 (on Meson8b) doesn't detect "hot-plugged" USB devices

Martin Blumenstingl martin.blumenstingl at googlemail.com
Wed Jul 4 07:16:41 PDT 2018


Hello Arthur,

On Wed, Jul 4, 2018 at 3:42 PM Artur Petrosyan
<Arthur.Petrosyan at synopsys.com> wrote:
>
> Martin,
>
> On 7/4/2018 17:13, Martin Blumenstingl wrote:
> > Hello Arthur, Hello Minas,
> >
> > On Wed, Jul 4, 2018 at 1:43 PM Artur Petrosyan
> > <Arthur.Petrosyan at synopsys.com> wrote:
> >>
> >> Hello Martin,
> >>
> >> On 7/4/2018 01:39, Martin Blumenstingl wrote:
> >>> Hello Minas,
> >>>
> >>> On Thu, May 10, 2018 at 11:44 AM Martin Blumenstingl
> >>> <martin.blumenstingl at googlemail.com> wrote:
> >>>>
> >>>> Hello Minas,
> >>>>
> >>>> On Mon, May 7, 2018 at 3:27 PM, Minas Harutyunyan
> >>>> <Minas.Harutyunyan at synopsys.com> wrote:
> >>>>> Hi Martin,
> >>>>>
> >>>>> On 5/7/2018 12:28 AM, Martin Blumenstingl wrote:
> >>>>>> Hello,
> >>>>>>
> >>>>>> I was a bit surprised to see that hot-plugging USB devices on Amlogic
> >>>>>> Meson8b (for example: Odroid-C1) is broken.
> >>>>>> to be fair: I *think* it worked before, but I cannot guarantee it nor
> >>>>>> can I say when it broke
> >>>>>>
> >>>>>> all examples below are from an Odroid-C1 board with Amlogic Meson8b (S805) SoC.
> >>>>>> this connects a (fixed, soldered down) 4-port USB hub to the dwc2
> >>>>>> controller (which is in "host" mode)
> >>>>>>
> >>>>>> during boot I see:
> >>>>>> [    1.651687] dwc2 c90c0000.usb: c90c0000.usb supply vusb_d not
> >>>>>> found, using dummy regulator
> >>>>>> [    1.654434] dwc2 c90c0000.usb: c90c0000.usb supply vusb_a not
> >>>>>> found, using dummy regulator
> >>>>>> [    1.732374] dwc2 c90c0000.usb: dwc2_check_params: Invalid parameter lpm=1
> >>>>>> [    1.733526] dwc2 c90c0000.usb: dwc2_check_params: Invalid parameter
> >>>>>> lpm_clock_gating=1
> >>>>>> [    1.741427] dwc2 c90c0000.usb: dwc2_check_params: Invalid parameter besl=1
> >>>>>> [    1.748305] dwc2 c90c0000.usb: dwc2_check_params: Invalid parameter
> >>>>>> hird_threshold_en=1
> >>>>>> [    1.756491] dwc2 c90c0000.usb: DWC OTG Controller
> >>>>>> [    1.760993] dwc2 c90c0000.usb: new USB bus registered, assigned bus number 1
> >>>>>> [    1.768046] dwc2 c90c0000.usb: irq 24, io mem 0xc90c0000
> >>>>>> [    1.773947] hub 1-0:1.0: USB hub found
> >>>>>> [    1.777063] hub 1-0:1.0: 1 port detected
> >>>>>> ...
> >>>>>> [    2.212432] usb 1-1: new high-speed USB device number 2 using dwc2
> >>>>>> [    2.464742] hub 1-1:1.0: USB hub found
> >>>>>> [    2.465118] hub 1-1:1.0: 4 ports detected
> >>>>>>
> >>>>>> if a USB device is plugged into one of the four USB ports during boot
> >>>>>> then it is detected automatically.
> >>>>>> if I plug in devices later they are not detected automatically (I have
> >>>>>> to run "lsusb -v" due to some reason, then hot-plugged devices are
> >>>>>> being detected)
> >>>>>> un-plugging USB devices is recognized instantly (no "lsusb" trickery
> >>>>>> is required)
> >>>>>>
> >>>>>> is this a known issue? how can I help debugging?
> >>>>>> any help is appreciated!
> >>>>>>
> >>>>>> below is the output of all dwc2 debugfs files.
> >>>>>>
> >>>>>>
> >>>>>> Regards
> >>>>>> Martin
> >>>>>>
> >>>>>>
> >>>>>> [rootodroidc1 c90c0000.usb]# cat dr_mode
> >>>>>> host
> >>>>>> [rootodroidc1 c90c0000.usb]# cat fifo
> >>>>>> Non-periodic FIFOs:
> >>>>>> RXFIFO: Size 0
> >>>>>> NPTXFIFO: Size 0, Start 0x00000000
> >>>>>>
> >>>>>> Periodic TXFIFOs:
> >>>>>> [rootodroidc1 c90c0000.usb]# cat hw_params
> >>>>>> op_mode                       : 5
> >>>>>> arch                          : 2
> >>>>>> dma_desc_enable               : 1
> >>>>>> enable_dynamic_fifo           : 1
> >>>>>> en_multiple_tx_fifo           : 0
> >>>>>> rx_fifo_size                  : 2048
> >>>>>> host_nperio_tx_fifo_size      : 2048
> >>>>>> dev_nperio_tx_fifo_size       : 0
> >>>>>> host_perio_tx_fifo_size       : 2048
> >>>>>> nperio_tx_q_depth             : 4
> >>>>>> host_perio_tx_q_depth         : 4
> >>>>>> dev_token_q_depth             : 8
> >>>>>> max_transfer_size             : 524287
> >>>>>> max_packet_count              : 1023
> >>>>>> host_channels                 : 16
> >>>>>> hs_phy_type                   : 1
> >>>>>> fs_phy_type                   : 0
> >>>>>> i2c_enable                    : 0
> >>>>>> num_dev_ep                    : 2
> >>>>>> num_dev_perio_in_ep           : 0
> >>>>>> total_fifo_size               : 1984
> >>>>>> power_optimized               : 1
> >>>>>> utmi_phy_data_width           : 1
> >>>>>> snpsid                        : 0x4f54310a
> >>>>>> dev_ep_dirs                   : 0x0
> >>>>>> [rootodroidc1 c90c0000.usb]# cat params
> >>>>>> otg_cap                       : 2
> >>>>>> dma_desc_enable               : 0
> >>>>>> dma_desc_fs_enable            : 0
> >>>>>> speed                         : 0
> >>>>>> enable_dynamic_fifo           : 1
> >>>>>> en_multiple_tx_fifo           : 0
> >>>>>> host_rx_fifo_size             : 512
> >>>>>> host_nperio_tx_fifo_size      : 500
> >>>>>> host_perio_tx_fifo_size       : 500
> >>>>>> max_transfer_size             : 524287
> >>>>>> max_packet_count              : 1023
> >>>>>> host_channels                 : 16
> >>>>>> phy_type                      : 1
> >>>>>> phy_utmi_width                : 16
> >>>>>> phy_ulpi_ddr                  : 0
> >>>>>> phy_ulpi_ext_vbus             : 0
> >>>>>> i2c_enable                    : 0
> >>>>>> ulpi_fs_ls                    : 0
> >>>>>> host_support_fs_ls_low_power  : 0
> >>>>>> host_ls_low_power_phy_clk     : 0
> >>>>>> ts_dline                      : 0
> >>>>>> reload_ctl                    : 1
> >>>>>> ahbcfg                        : 0xa
> >>>>>> uframe_sched                  : 0
> >>>>>> external_id_pin_ctl           : 0
> >>>>>> power_down                    : 1
> >>>>>> lpm                           : 0
> >>>>>> lpm_clock_gating              : 0
> >>>>>> besl                          : 0
> >>>>>> hird_threshold_en             : 0
> >>>>>> hird_threshold                : 4
> >>>>>> host_dma                      : 1
> >>>>>> g_dma                         : 0
> >>>>>> g_dma_desc                    : 0
> >>>>>> g_rx_fifo_size                : 0
> >>>>>> g_np_tx_fifo_size             : 0
> >>>>>> g_tx_fifo_size[0]             : 0
> >>>>>> g_tx_fifo_size[1]             : 0
> >>>>>> g_tx_fifo_size[2]             : 0
> >>>>>> g_tx_fifo_size[3]             : 0
> >>>>>> g_tx_fifo_size[4]             : 0
> >>>>>> g_tx_fifo_size[5]             : 0
> >>>>>> g_tx_fifo_size[6]             : 0
> >>>>>> g_tx_fifo_size[7]             : 0
> >>>>>> g_tx_fifo_size[8]             : 0
> >>>>>> g_tx_fifo_size[9]             : 0
> >>>>>> g_tx_fifo_size[10]            : 0
> >>>>>> g_tx_fifo_size[11]            : 0
> >>>>>> g_tx_fifo_size[12]            : 0
> >>>>>> g_tx_fifo_size[13]            : 0
> >>>>>> g_tx_fifo_size[14]            : 0
> >>>>>> g_tx_fifo_size[15]            : 0
> >>>>>> [rootodroidc1 c90c0000.usb]# cat state
> >>>>>> DCFG=0x00000000, DCTL=0x00000000, DSTS=0x00000000
> >>>>>> DIEPMSK=0x00000000, DOEPMASK=0x00000000
> >>>>>> GINTMSK=0xf0000000, GINTSTS=0x00000001
> >>>>>> DAINTMSK=0x00000000, DAINT=0x00000000
> >>>>>> GNPTXSTS=0x00000000, GRXSTSR=00000000
> >>>>>>
> >>>>>> Endpoint status:
> >>>>>> [rootodroidc1 c90c0000.usb]# cat testmode
> >>>>>> no test
> >>>>>> [rootodroidc1 c90c0000.usb]# cat regdump
> >>>>>> <system hangs>
> >>>>>>
> >>>>>
> >>>>> Your core configured for SRP capable host only mode "op_mode: 5", but
> >>>>> USBCFG programmed for "otg_cap = 2" which mean
> >>>>> "DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE", i.e. no SRP.
> >>>>> 1. Please try to set "p->otg_cap = DWC2_CAP_PARAM_SRP_ONLY_CAPABLE;"
> >>>> this results in the (soldered down) USB hub not even being detected anymore
> >>>> # dmesg | grep c90c0000
> >>>> [    1.771610] dwc2 c90c0000.usb: c90c0000.usb supply vusb_d not
> >>>> found, using dummy regulator
> >>>> [    1.779262] dwc2 c90c0000.usb: c90c0000.usb supply vusb_a not
> >>>> found, using dummy regulator
> >>>> [    1.852346] dwc2 c90c0000.usb: dwc2_check_params: Invalid parameter lpm=1
> >>>> [    1.853496] dwc2 c90c0000.usb: dwc2_check_params: Invalid parameter
> >>>> lpm_clock_gating=1
> >>>> [    1.861397] dwc2 c90c0000.usb: dwc2_check_params: Invalid parameter besl=1
> >>>> [    1.868274] dwc2 c90c0000.usb: dwc2_check_params: Invalid parameter
> >>>> hird_threshold_en=1
> >>>> [    1.876357] dwc2 c90c0000.usb: DWC OTG Controller
> >>>> [    1.880954] dwc2 c90c0000.usb: new USB bus registered, assigned bus number 2
> >>>> [    1.888010] dwc2 c90c0000.usb: irq 25, io mem 0xc90c0000
> >>>> [    2.002455] dwc2 c90c0000.usb: Overcurrent change detected
> >>>> [    2.132721] dwc2 c90c0000.usb: Overcurrent change detected
> >>>> [    2.252442] dwc2 c90c0000.usb: Overcurrent change detected
> >>>> <lsusb -v here>
> >>>> [   47.682374] dwc2 c90c0000.usb: Overcurrent change detected
> >>>>
> >>>> (this is with "host only" mode being configured and DRD mode being
> >>>> disabled in the driver)
> >>>>
> >>>>> 2. Looks like your driver configured for DRD mode. Change it to "HOST
> >>>>> only" mode.
> >>>> Amlogic Meson8, Meson8b, Meson8m2 and GXBB SoCs come with two dwc2 controllers:
> >>>> - a host-only one (which is the one I'm seeing problems with)
> >>>> - an "OTG capable" one (where the dwc2's OTG detection IRQ/detection
> >>>> *may* not be routed dwc2)
> >>>>
> >>>> this is why my driver was configured for DRD mode
> >>>> but let's focus on the host-only core for now
> >>>>
> >>>> the only documentation about the USB implementation in these SoCs is
> >>>> in the public S805 (Meson8b) and S905 (GXBB) datasheets.
> >>>> the following sections are from these datasheets (both use an
> >>>> indentical description):
> >>>>
> >>>> The OTG controller features:
> >>>> * Support for the following speeds: High-Speed (HS,
> >>>> 480-Mbps),Full-Speed (FS, 12-Mbps) and Low-Speed (LS, 1.5-Mbps) modes
> >>>> * Multiple DMA/non DMA mode access support on the application side
> >>>> * Supports up to 16 bidirectional endpoints, including control endpoint 0.
> >>>> * Supports Session Request Protocol (SRP) and Host Negotiation Protocol (HNP)
> >>>> * Supports up to 16 host channels.
> >>>>
> >>>> The Host controller features:
> >>>> * Support for the following speeds: High-Speed (HS,
> >>>> 480-Mbps),Full-Speed (FS, 12-Mbps) and Low-Speed (LS, 1.5-Mbps) modes
> >>>> * Multiple DMA/non DMA mode access support on the application side
> >>>> * Supports up to 16 host  channels.
> >>>>
> >>>>> 2. Please send us verbose debug log when device not recognized and after
> >>>>> lsusb when device recognized.
> >>>> do you want to see the dev_dbg() and dwc2_sch_dbg() output from the
> >>>> dwc2 driver or is there some other way?
> >>> gentle ping, did you have time to look into my questions so I can give
> >>> you everything you need?
> >>
> >> Sorry for the late reply. We need verbose debug logs with dev_dbg().
> >> So could you please provide verbose debug loges as Minas requested
> >> earlier (dwc2_sch_dbg() not required).
> > OK, I have:
> > CONFIG_USB_DWC2=y
> > CONFIG_USB_DWC2_HOST=y
> > # CONFIG_USB_DWC2_PERIPHERAL is not set
> > # CONFIG_USB_DWC2_DUAL_ROLE is not set
> > # CONFIG_USB_DWC2_PCI is not set
> > CONFIG_USB_DWC2_DEBUG=y
> > # CONFIG_USB_DWC2_VERBOSE is not set
>
> Could you please enable the verbose debug and send the log as requested?
I see, I missed the *verbose* bit - I now have:
CONFIG_USB_DWC2=y
CONFIG_USB_DWC2_HOST=y
# CONFIG_USB_DWC2_PERIPHERAL is not set
# CONFIG_USB_DWC2_DUAL_ROLE is not set
# CONFIG_USB_DWC2_PCI is not set
CONFIG_USB_DWC2_DEBUG=y
CONFIG_USB_DWC2_VERBOSE=y
# CONFIG_USB_DWC2_TRACK_MISSED_SOFS is not set
CONFIG_USB_DWC2_DEBUG_PERIODIC=y

unfortunately it seems that plugging in seems to fill the kmsg buffer
instantly, so I cannot (at least I don't know how - do you have any
idea how to get around this?) get the information from the second
where I'm plugging in the thumb drive
I attached everything I have


Regards
Martin
-------------- next part --------------
[    0.000000] Booting Linux on physical CPU 0x200
[    0.000000] Linux version 4.18.0-rc3-00147-gcaaf8b8102ca-dirty (xdarklight at blackbox) (gcc version 8.1.0 (Arch Repository)) #2877 SMP Wed Jul 4 15:57:35 CEST 2018
[    0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Hardkernel ODROID-C1
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 64 MiB at 0x3c000000
[    0.000000] On node 0 totalpages: 261632
[    0.000000]   Normal zone: 1532 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 196096 pages, LIFO batch:31
[    0.000000]   HighMem zone: 65536 pages, LIFO batch:15
[    0.000000] random: get_random_bytes called from start_kernel+0xa0/0x464 with crng_init=0
[    0.000000] percpu: Embedded 141 pages/cpu @(ptrval) s547468 r8192 d21876 u577536
[    0.000000] pcpu-alloc: s547468 r8192 d21876 u577536 alloc=141*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 260100
[    0.000000] Kernel command line: console=ttyAML0,115200 root=/dev/mmcblk0p2 rootwait=1 rootdelay=2
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 934340K/1046528K available (10240K kernel code, 783K rwdata, 2616K rodata, 2048K init, 4253K bss, 46652K reserved, 65536K cma-reserved, 196608K highmem)
[    0.000000] Virtual kernel memory layout:
                   vector  : 0xffff0000 - 0xffff1000   (   4 kB)
                   fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
                   vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
                   lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
                   pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
                   modules : 0xbf000000 - 0xbfe00000   (  14 MB)
                     .text : 0x(ptrval) - 0x(ptrval)   (11232 kB)
                     .init : 0x(ptrval) - 0x(ptrval)   (2048 kB)
                     .data : 0x(ptrval) - 0x(ptrval)   ( 784 kB)
                      .bss : 0x(ptrval) - 0x(ptrval)   (4254 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU event tracing is enabled.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] irq_meson_gpio: 119 to 8 gpio interrupt mux initialized
[    0.000000] L2C: DT/platform modifies aux control register: 0x02060000 -> 0x02460000
[    0.000000] L2C-310 erratum 769419 enabled
[    0.000000] L2C-310 ID prefetch enabled, offset 1 lines
[    0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[    0.000000] L2C-310 cache controller enabled, 8 ways, 512 kB
[    0.000000] L2C-310: CACHE_ID 0x4100a0c9, AUX_CTRL 0x36460000
[    0.000011] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns
[    0.000028] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns
[    0.000443] smp_twd: clock not found -2
[    0.000601] Console: colour dummy device 80x30
[    0.000632] Calibrating local timer... 299.82MHz.
[    0.060251] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)
[    0.100262] pid_max: default: 32768 minimum: 301
[    0.100387] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.100400] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.100858] CPU: Testing write buffer coherency: ok
[    0.101116] CPU0: thread -1, cpu 0, socket 2, mpidr 80000200
[    0.101686] Setting up static identity map for 0x300000 - 0x300060
[    0.101804] Hierarchical SRCU implementation.
[    0.102415] EFI services will not be available.
[    0.102692] smp: Bringing up secondary CPUs ...
[    0.140230] CPU1: thread -1, cpu 1, socket 2, mpidr 80000201
[    0.180206] CPU2: thread -1, cpu 2, socket 2, mpidr 80000202
[    0.220181] CPU3: thread -1, cpu 3, socket 2, mpidr 80000203
[    0.220283] smp: Brought up 1 node, 4 CPUs
[    0.220305] SMP: Total of 4 processors activated (3181.77 BogoMIPS).
[    0.220311] CPU: All CPU(s) started in SVC mode.
[    0.220945] devtmpfs: initialized
[    0.223365] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[    0.223544] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.223562] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.226276] pinctrl core: initialized pinctrl subsystem
[    0.226841] DMI not present or invalid.
[    0.227117] NET: Registered protocol family 16
[    0.228704] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.229748] cpuidle: using governor menu
[    0.229879] No ATAGs?
[    0.229979] hw-breakpoint: found 2 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.229989] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.243356] vgaarb: loaded
[    0.243863] SCSI subsystem initialized
[    0.244087] libata version 3.00 loaded.
[    0.244264] usbcore: registered new interface driver usbfs
[    0.244306] usbcore: registered new interface driver hub
[    0.244357] usbcore: registered new device driver usb
[    0.244521] pps_core: LinuxPPS API ver. 1 registered
[    0.244528] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti at linux.it>
[    0.244545] PTP clock support registered
[    0.244642] EDAC MC: Ver: 3.0.0
[    0.245425] Bluetooth: Core ver 2.22
[    0.245461] NET: Registered protocol family 31
[    0.245468] Bluetooth: HCI device and connection manager initialized
[    0.245481] Bluetooth: HCI socket layer initialized
[    0.245490] Bluetooth: L2CAP socket layer initialized
[    0.245516] Bluetooth: SCO socket layer initialized
[    0.245930] clocksource: Switched to clocksource timer
[    0.310112] NET: Registered protocol family 2
[    0.310553] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[    0.310578] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.310649] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.310754] TCP: Hash tables configured (established 8192 bind 8192)
[    0.310855] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.310899] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.311071] NET: Registered protocol family 1
[    0.311509] RPC: Registered named UNIX socket transport module.
[    0.311520] RPC: Registered udp transport module.
[    0.311525] RPC: Registered tcp transport module.
[    0.311530] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.311926] PCI: CLS 0 bytes, default 64
[    0.312089] Trying to unpack rootfs image as initramfs...
[    0.374250] Freeing initrd memory: 14928K
[    0.375128] hw perfevents: enabled with armv7_cortex_a5 PMU driver, 3 counters available
[    0.376425] Initialise system trusted keyrings
[    0.376566] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[    0.381169] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.381765] NFS: Registering the id_resolver key type
[    0.381788] Key type id_resolver registered
[    0.381793] Key type id_legacy registered
[    0.381824] ntfs: driver 2.1.32 [Flags: R/O].
[    0.382510] pstore: using deflate compression
[    0.386324] jitterentropy: Initialization failed with host not compliant with requirements: 2
[    0.386448] Key type asymmetric registered
[    0.386456] Asymmetric key parser 'x509' registered
[    0.386513] bounce: pool size: 64 pages
[    0.386568] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.386577] io scheduler noop registered
[    0.386583] io scheduler deadline registered
[    0.386777] io scheduler cfq registered (default)
[    0.386785] io scheduler mq-deadline registered
[    0.386791] io scheduler kyber registered
[    0.388562] GPIO line 417 (usb-hub-reset) hogged as output/high
[    0.393237] soc soc0: Amlogic Meson8b (S805) RevA (1b - 0:B72) detected
[    0.435952] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.437694] c81004c0.serial: ttyAML0 at MMIO 0xc81004c0 (irq = 24, base_baud = 9960937) is a meson_uart
[    1.150529] console [ttyAML0] enabled
[    1.154570] STMicroelectronics ASC driver initialized
[    1.167199] brd: module loaded
[    1.173396] loop: module loaded
[    1.175461] libphy: Fixed MDIO Bus: probed
[    1.176371] CAN device driver interface
[    1.179084] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.184620] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.190586] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[    1.197498] igb: Copyright (c) 2007-2014 Intel Corporation.
[    1.203782] meson8b-dwmac c9410000.ethernet: PTP uses main clock
[    1.209468] meson8b-dwmac c9410000.ethernet: User ID: 0x10, Synopsys ID: 0x37
[    1.216183] meson8b-dwmac c9410000.ethernet: 	DWMAC1000
[    1.221357] meson8b-dwmac c9410000.ethernet: DMA HW capability register supported
[    1.228849] meson8b-dwmac c9410000.ethernet: RX Checksum Offload Engine supported
[    1.236304] meson8b-dwmac c9410000.ethernet: COE Type 2
[    1.241502] meson8b-dwmac c9410000.ethernet: TX Checksum insertion supported
[    1.248548] meson8b-dwmac c9410000.ethernet: Wake-Up On Lan supported
[    1.254990] meson8b-dwmac c9410000.ethernet: Normal descriptors
[    1.260879] meson8b-dwmac c9410000.ethernet: Ring mode enabled
[    1.266700] meson8b-dwmac c9410000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.345943] libphy: stmmac: probed
[    1.351776] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[    1.353583] usbcore: registered new interface driver pegasus
[    1.359255] usbcore: registered new interface driver asix
[    1.364588] usbcore: registered new interface driver ax88179_178a
[    1.370684] usbcore: registered new interface driver cdc_ether
[    1.376508] usbcore: registered new interface driver smsc75xx
[    1.382224] usbcore: registered new interface driver smsc95xx
[    1.387961] usbcore: registered new interface driver net1080
[    1.393598] usbcore: registered new interface driver cdc_subset
[    1.399511] usbcore: registered new interface driver zaurus
[    1.405077] usbcore: registered new interface driver cdc_ncm
[    1.411136] dwc2 c90c0000.usb: mapped PA c90c0000 to VA (ptrval)
[    1.411394] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.417206] ehci-pci: EHCI PCI platform driver
[    1.421648] ehci-platform: EHCI generic platform driver
[    1.426925] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.433010] ohci-pci: OHCI PCI platform driver
[    1.437466] ohci-platform: OHCI generic platform driver
[    1.442929] usbcore: registered new interface driver usb-storage
[    1.449196] udc-core: couldn't find an available UDC - added [g_cdc] to list of pending drivers
[    1.457919] i2c /dev entries driver
[    1.461201] IR NEC protocol handler initialized
[    1.465296] IR RC5(x/sz) protocol handler initialized
[    1.470352] IR RC6 protocol handler initialized
[    1.474848] IR JVC protocol handler initialized
[    1.479375] IR Sony protocol handler initialized
[    1.483969] IR SANYO protocol handler initialized
[    1.488666] IR Sharp protocol handler initialized
[    1.493345] IR MCE Keyboard/mouse protocol handler initialized
[    1.499174] IR XMP protocol handler initialized
[    1.503874] Registered IR keymap rc-empty
[    1.507758] rc rc0: meson-ir as /devices/platform/soc/c8100000.aobus/c8100480.ir-receiver/rc/rc0
[    1.516578] input: meson-ir as /devices/platform/soc/c8100000.aobus/c8100480.ir-receiver/rc/rc0/input0
[    1.526086] meson-ir c8100480.ir-receiver: receiver initialized
[    1.532681] meson_wdt c1109900.watchdog: Watchdog enabled (timeout=8 sec, nowayout=0)
[    1.539652] Bluetooth: HCI UART driver ver 2.3
[    1.543887] Bluetooth: HCI UART protocol H4 registered
[    1.549024] Bluetooth: HCI UART protocol BCSP registered
[    1.554307] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    1.560646] Bluetooth: HCI UART protocol Broadcom registered
[    1.566243] Bluetooth: HCI UART protocol QCA registered
[    1.573005] sdhci: Secure Digital Host Controller Interface driver
[    1.577605] sdhci: Copyright(c) Pierre Ossman
[    1.581921] Synopsys Designware Multimedia Card Interface Driver
[    1.589324] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.594147] ledtrig-cpu: registered to indicate activity on CPUs
[    1.599721] usbcore: registered new interface driver usbhid
[    1.605106] usbhid: USB HID core driver
[    1.610195] NET: Registered protocol family 10
[    1.614061] Segment Routing with IPv6
[    1.617077] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    1.623349] NET: Registered protocol family 17
[    1.627386] can: controller area network core (rev 20170425 abi 9)
[    1.633550] NET: Registered protocol family 29
[    1.637954] can: raw protocol (rev 20170425)
[    1.642188] can: broadcast manager protocol (rev 20170425 t)
[    1.647852] can: netlink gateway (rev 20170425) max_hops=1
[    1.653541] Key type dns_resolver registered
[    1.657681] ThumbEE CPU extension supported.
[    1.661819] Registering SWP/SWPB emulation handler
[    1.667106] Loading compiled-in X.509 certificates
[    1.678501] dwc2 c90c0000.usb: mapped PA c90c0000 to VA (ptrval)
[    1.678541] dwc2 c90c0000.usb: c90c0000.usb supply vusb_d not found, using dummy regulator
[    1.681213] dwc2 c90c0000.usb: c90c0000.usb supply vusb_a not found, using dummy regulator
[    1.689516] dwc2 c90c0000.usb: registering common handler for irq25
[    1.690625] dwc2 c90c0000.usb: dwc2_core_reset()
[    1.690635] dwc2 c90c0000.usb: Core Release: 3.10a (snpsid=4f54310a)
[    1.690641] dwc2 c90c0000.usb: Forcing mode to host
[    1.755957] dwc2 c90c0000.usb: dwc2_check_params: Invalid parameter lpm=1
[    1.757107] dwc2 c90c0000.usb: dwc2_check_params: Invalid parameter lpm_clock_gating=1
[    1.765013] dwc2 c90c0000.usb: dwc2_check_params: Invalid parameter besl=1
[    1.771887] dwc2 c90c0000.usb: dwc2_check_params: Invalid parameter hird_threshold_en=1
[    1.779871] dwc2 c90c0000.usb: DWC OTG HCD INIT
[    1.779876] dwc2 c90c0000.usb: hcfg=00000200
[    1.779886] dwc2 c90c0000.usb: dwc2_core_init((ptrval))
[    1.779890] dwc2 c90c0000.usb: HS UTMI+ PHY selected
[    1.779895] dwc2 c90c0000.usb: Internal DMA Mode
[    1.779900] dwc2 c90c0000.usb: Host Mode
[    1.780252] dwc2 c90c0000.usb: DWC OTG Controller
[    1.784571] dwc2 c90c0000.usb: new USB bus registered, assigned bus number 1
[    1.791636] dwc2 c90c0000.usb: irq 25, io mem 0xc90c0000
[    1.796893] dwc2 c90c0000.usb: DWC OTG HCD START
[    1.796902] dwc2 c90c0000.usb: dwc2_core_host_init((ptrval))
[    1.796908] dwc2 c90c0000.usb: Initializing HCFG.FSLSPClkSel to 00000000
[    1.796914] dwc2 c90c0000.usb: initial grxfsiz=00000800
[    1.796919] dwc2 c90c0000.usb: new grxfsiz=00000200
[    1.796923] dwc2 c90c0000.usb: initial gnptxfsiz=08000800
[    1.796927] dwc2 c90c0000.usb: new gnptxfsiz=01f40200
[    1.796932] dwc2 c90c0000.usb: initial hptxfsiz=08000000
[    1.796936] dwc2 c90c0000.usb: new hptxfsiz=01f403f4
[    1.796941] dwc2 c90c0000.usb: Flush Tx FIFO 16
[    1.796948] dwc2 c90c0000.usb: dwc2_flush_rx_fifo()
[    1.796960] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 0
[    1.796965] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 1
[    1.796970] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 2
[    1.796975] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 3
[    1.796979] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 4
[    1.796984] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 5
[    1.796989] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 6
[    1.796994] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 7
[    1.796998] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 8
[    1.797003] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 9
[    1.797008] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 10
[    1.797012] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 11
[    1.797017] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 12
[    1.797022] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 13
[    1.797026] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 14
[    1.797031] dwc2 c90c0000.usb: dwc2_core_host_init: Halt channel 15
[    1.797036] dwc2 c90c0000.usb: Init: Port Power? op_state=9
[    1.797040] dwc2 c90c0000.usb: Init: Power Port (0)
[    1.797044] dwc2 c90c0000.usb: dwc2_enable_host_interrupts()
[    1.797049] dwc2 c90c0000.usb: DWC OTG HCD Has Root Hub
[    1.798932] dwc2 c90c0000.usb: DWC OTG HCD EP RESET: bEndpointAddress=0x81
[    1.799047] hub 1-0:1.0: USB hub found
[    1.800617] dwc2 c90c0000.usb: GetHubDescriptor
[    1.800645] hub 1-0:1.0: 1 port detected
[    1.804541] dwc2 c90c0000.usb: GetHubStatus
[    1.804608] dwc2 c90c0000.usb: SetPortFeature
[    1.804767] dwc2 c90c0000.usb: 
[    1.804772] dwc2 c90c0000.usb: ************************************************************
[    1.804775] dwc2 c90c0000.usb: HCD State:
[    1.804779] dwc2 c90c0000.usb:   Num channels: 16
[    1.804783] dwc2 c90c0000.usb:   Channel 0:
[    1.804788] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.804791] dwc2 c90c0000.usb:     speed: 0
[    1.804795] dwc2 c90c0000.usb:     ep_type: 0
[    1.804798] dwc2 c90c0000.usb:     max_packet: 0
[    1.804802] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.804805] dwc2 c90c0000.usb:     multi_count: 0
[    1.804809] dwc2 c90c0000.usb:     xfer_started: 0
[    1.804814] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.804817] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.804821] dwc2 c90c0000.usb:     xfer_len: 0
[    1.804825] dwc2 c90c0000.usb:     xfer_count: 0
[    1.804828] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.804832] dwc2 c90c0000.usb:     halt_pending: 0
[    1.804835] dwc2 c90c0000.usb:     halt_status: 0
[    1.804839] dwc2 c90c0000.usb:     do_split: 0
[    1.804842] dwc2 c90c0000.usb:     complete_split: 0
[    1.804846] dwc2 c90c0000.usb:     hub_addr: 0
[    1.804849] dwc2 c90c0000.usb:     hub_port: 0
[    1.804853] dwc2 c90c0000.usb:     xact_pos: 0
[    1.804856] dwc2 c90c0000.usb:     requests: 0
[    1.804860] dwc2 c90c0000.usb:     qh:   (null)
[    1.804863] dwc2 c90c0000.usb:   Channel 1:
[    1.804868] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.804871] dwc2 c90c0000.usb:     speed: 0
[    1.804875] dwc2 c90c0000.usb:     ep_type: 0
[    1.804879] dwc2 c90c0000.usb:     max_packet: 0
[    1.804882] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.804886] dwc2 c90c0000.usb:     multi_count: 0
[    1.804889] dwc2 c90c0000.usb:     xfer_started: 0
[    1.804893] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.804896] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.804900] dwc2 c90c0000.usb:     xfer_len: 0
[    1.804903] dwc2 c90c0000.usb:     xfer_count: 0
[    1.804907] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.804910] dwc2 c90c0000.usb:     halt_pending: 0
[    1.804914] dwc2 c90c0000.usb:     halt_status: 0
[    1.804917] dwc2 c90c0000.usb:     do_split: 0
[    1.804921] dwc2 c90c0000.usb:     complete_split: 0
[    1.804924] dwc2 c90c0000.usb:     hub_addr: 0
[    1.804928] dwc2 c90c0000.usb:     hub_port: 0
[    1.804931] dwc2 c90c0000.usb:     xact_pos: 0
[    1.804935] dwc2 c90c0000.usb:     requests: 0
[    1.804938] dwc2 c90c0000.usb:     qh:   (null)
[    1.804942] dwc2 c90c0000.usb:   Channel 2:
[    1.804946] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.804950] dwc2 c90c0000.usb:     speed: 0
[    1.804953] dwc2 c90c0000.usb:     ep_type: 0
[    1.804957] dwc2 c90c0000.usb:     max_packet: 0
[    1.804960] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.804964] dwc2 c90c0000.usb:     multi_count: 0
[    1.804967] dwc2 c90c0000.usb:     xfer_started: 0
[    1.804971] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.804974] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.804978] dwc2 c90c0000.usb:     xfer_len: 0
[    1.804981] dwc2 c90c0000.usb:     xfer_count: 0
[    1.804985] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.804988] dwc2 c90c0000.usb:     halt_pending: 0
[    1.804992] dwc2 c90c0000.usb:     halt_status: 0
[    1.804995] dwc2 c90c0000.usb:     do_split: 0
[    1.804999] dwc2 c90c0000.usb:     complete_split: 0
[    1.805002] dwc2 c90c0000.usb:     hub_addr: 0
[    1.805006] dwc2 c90c0000.usb:     hub_port: 0
[    1.805009] dwc2 c90c0000.usb:     xact_pos: 0
[    1.805013] dwc2 c90c0000.usb:     requests: 0
[    1.805016] dwc2 c90c0000.usb:     qh:   (null)
[    1.805020] dwc2 c90c0000.usb:   Channel 3:
[    1.805024] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.805028] dwc2 c90c0000.usb:     speed: 0
[    1.805031] dwc2 c90c0000.usb:     ep_type: 0
[    1.805035] dwc2 c90c0000.usb:     max_packet: 0
[    1.805038] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.805042] dwc2 c90c0000.usb:     multi_count: 0
[    1.805045] dwc2 c90c0000.usb:     xfer_started: 0
[    1.805049] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.805052] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.805056] dwc2 c90c0000.usb:     xfer_len: 0
[    1.805059] dwc2 c90c0000.usb:     xfer_count: 0
[    1.805063] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.805066] dwc2 c90c0000.usb:     halt_pending: 0
[    1.805070] dwc2 c90c0000.usb:     halt_status: 0
[    1.805073] dwc2 c90c0000.usb:     do_split: 0
[    1.805077] dwc2 c90c0000.usb:     complete_split: 0
[    1.805080] dwc2 c90c0000.usb:     hub_addr: 0
[    1.805084] dwc2 c90c0000.usb:     hub_port: 0
[    1.805087] dwc2 c90c0000.usb:     xact_pos: 0
[    1.805091] dwc2 c90c0000.usb:     requests: 0
[    1.805094] dwc2 c90c0000.usb:     qh:   (null)
[    1.805098] dwc2 c90c0000.usb:   Channel 4:
[    1.805102] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.805106] dwc2 c90c0000.usb:     speed: 0
[    1.805109] dwc2 c90c0000.usb:     ep_type: 0
[    1.805113] dwc2 c90c0000.usb:     max_packet: 0
[    1.805116] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.805120] dwc2 c90c0000.usb:     multi_count: 0
[    1.805123] dwc2 c90c0000.usb:     xfer_started: 0
[    1.805127] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.805130] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.805134] dwc2 c90c0000.usb:     xfer_len: 0
[    1.805137] dwc2 c90c0000.usb:     xfer_count: 0
[    1.805141] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.805145] dwc2 c90c0000.usb:     halt_pending: 0
[    1.805148] dwc2 c90c0000.usb:     halt_status: 0
[    1.805152] dwc2 c90c0000.usb:     do_split: 0
[    1.805155] dwc2 c90c0000.usb:     complete_split: 0
[    1.805159] dwc2 c90c0000.usb:     hub_addr: 0
[    1.805162] dwc2 c90c0000.usb:     hub_port: 0
[    1.805166] dwc2 c90c0000.usb:     xact_pos: 0
[    1.805169] dwc2 c90c0000.usb:     requests: 0
[    1.805173] dwc2 c90c0000.usb:     qh:   (null)
[    1.805176] dwc2 c90c0000.usb:   Channel 5:
[    1.805181] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.805184] dwc2 c90c0000.usb:     speed: 0
[    1.805188] dwc2 c90c0000.usb:     ep_type: 0
[    1.805191] dwc2 c90c0000.usb:     max_packet: 0
[    1.805195] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.805198] dwc2 c90c0000.usb:     multi_count: 0
[    1.805202] dwc2 c90c0000.usb:     xfer_started: 0
[    1.805205] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.805209] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.805212] dwc2 c90c0000.usb:     xfer_len: 0
[    1.805216] dwc2 c90c0000.usb:     xfer_count: 0
[    1.805220] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.805223] dwc2 c90c0000.usb:     halt_pending: 0
[    1.805227] dwc2 c90c0000.usb:     halt_status: 0
[    1.805230] dwc2 c90c0000.usb:     do_split: 0
[    1.805234] dwc2 c90c0000.usb:     complete_split: 0
[    1.805237] dwc2 c90c0000.usb:     hub_addr: 0
[    1.805241] dwc2 c90c0000.usb:     hub_port: 0
[    1.805244] dwc2 c90c0000.usb:     xact_pos: 0
[    1.805247] dwc2 c90c0000.usb:     requests: 0
[    1.805251] dwc2 c90c0000.usb:     qh:   (null)
[    1.805254] dwc2 c90c0000.usb:   Channel 6:
[    1.805259] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.805262] dwc2 c90c0000.usb:     speed: 0
[    1.805266] dwc2 c90c0000.usb:     ep_type: 0
[    1.805269] dwc2 c90c0000.usb:     max_packet: 0
[    1.805273] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.805276] dwc2 c90c0000.usb:     multi_count: 0
[    1.805280] dwc2 c90c0000.usb:     xfer_started: 0
[    1.805283] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.805287] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.805290] dwc2 c90c0000.usb:     xfer_len: 0
[    1.805294] dwc2 c90c0000.usb:     xfer_count: 0
[    1.805298] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.805301] dwc2 c90c0000.usb:     halt_pending: 0
[    1.805305] dwc2 c90c0000.usb:     halt_status: 0
[    1.805308] dwc2 c90c0000.usb:     do_split: 0
[    1.805312] dwc2 c90c0000.usb:     complete_split: 0
[    1.805315] dwc2 c90c0000.usb:     hub_addr: 0
[    1.805319] dwc2 c90c0000.usb:     hub_port: 0
[    1.805322] dwc2 c90c0000.usb:     xact_pos: 0
[    1.805326] dwc2 c90c0000.usb:     requests: 0
[    1.805329] dwc2 c90c0000.usb:     qh:   (null)
[    1.805333] dwc2 c90c0000.usb:   Channel 7:
[    1.805337] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.805340] dwc2 c90c0000.usb:     speed: 0
[    1.805344] dwc2 c90c0000.usb:     ep_type: 0
[    1.805347] dwc2 c90c0000.usb:     max_packet: 0
[    1.805351] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.805354] dwc2 c90c0000.usb:     multi_count: 0
[    1.805358] dwc2 c90c0000.usb:     xfer_started: 0
[    1.805361] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.805365] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.805368] dwc2 c90c0000.usb:     xfer_len: 0
[    1.805372] dwc2 c90c0000.usb:     xfer_count: 0
[    1.805375] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.805379] dwc2 c90c0000.usb:     halt_pending: 0
[    1.805382] dwc2 c90c0000.usb:     halt_status: 0
[    1.805386] dwc2 c90c0000.usb:     do_split: 0
[    1.805389] dwc2 c90c0000.usb:     complete_split: 0
[    1.805393] dwc2 c90c0000.usb:     hub_addr: 0
[    1.805396] dwc2 c90c0000.usb:     hub_port: 0
[    1.805400] dwc2 c90c0000.usb:     xact_pos: 0
[    1.805403] dwc2 c90c0000.usb:     requests: 0
[    1.805407] dwc2 c90c0000.usb:     qh:   (null)
[    1.805410] dwc2 c90c0000.usb:   Channel 8:
[    1.805415] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.805418] dwc2 c90c0000.usb:     speed: 0
[    1.805422] dwc2 c90c0000.usb:     ep_type: 0
[    1.805425] dwc2 c90c0000.usb:     max_packet: 0
[    1.805429] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.805432] dwc2 c90c0000.usb:     multi_count: 0
[    1.805436] dwc2 c90c0000.usb:     xfer_started: 0
[    1.805439] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.805443] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.805446] dwc2 c90c0000.usb:     xfer_len: 0
[    1.805450] dwc2 c90c0000.usb:     xfer_count: 0
[    1.805453] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.805457] dwc2 c90c0000.usb:     halt_pending: 0
[    1.805460] dwc2 c90c0000.usb:     halt_status: 0
[    1.805464] dwc2 c90c0000.usb:     do_split: 0
[    1.805467] dwc2 c90c0000.usb:     complete_split: 0
[    1.805471] dwc2 c90c0000.usb:     hub_addr: 0
[    1.805474] dwc2 c90c0000.usb:     hub_port: 0
[    1.805477] dwc2 c90c0000.usb:     xact_pos: 0
[    1.805481] dwc2 c90c0000.usb:     requests: 0
[    1.805485] dwc2 c90c0000.usb:     qh:   (null)
[    1.805488] dwc2 c90c0000.usb:   Channel 9:
[    1.805492] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.805496] dwc2 c90c0000.usb:     speed: 0
[    1.805499] dwc2 c90c0000.usb:     ep_type: 0
[    1.805503] dwc2 c90c0000.usb:     max_packet: 0
[    1.805506] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.805510] dwc2 c90c0000.usb:     multi_count: 0
[    1.805513] dwc2 c90c0000.usb:     xfer_started: 0
[    1.805517] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.805521] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.805524] dwc2 c90c0000.usb:     xfer_len: 0
[    1.805528] dwc2 c90c0000.usb:     xfer_count: 0
[    1.805531] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.805535] dwc2 c90c0000.usb:     halt_pending: 0
[    1.805538] dwc2 c90c0000.usb:     halt_status: 0
[    1.805542] dwc2 c90c0000.usb:     do_split: 0
[    1.805545] dwc2 c90c0000.usb:     complete_split: 0
[    1.805549] dwc2 c90c0000.usb:     hub_addr: 0
[    1.805552] dwc2 c90c0000.usb:     hub_port: 0
[    1.805555] dwc2 c90c0000.usb:     xact_pos: 0
[    1.805559] dwc2 c90c0000.usb:     requests: 0
[    1.805562] dwc2 c90c0000.usb:     qh:   (null)
[    1.805566] dwc2 c90c0000.usb:   Channel 10:
[    1.805571] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.805574] dwc2 c90c0000.usb:     speed: 0
[    1.805586] dwc2 c90c0000.usb:     ep_type: 0
[    1.805589] dwc2 c90c0000.usb:     max_packet: 0
[    1.805593] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.805596] dwc2 c90c0000.usb:     multi_count: 0
[    1.805600] dwc2 c90c0000.usb:     xfer_started: 0
[    1.805603] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.805608] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.805611] dwc2 c90c0000.usb:     xfer_len: 0
[    1.805614] dwc2 c90c0000.usb:     xfer_count: 0
[    1.805618] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.805622] dwc2 c90c0000.usb:     halt_pending: 0
[    1.805625] dwc2 c90c0000.usb:     halt_status: 0
[    1.805628] dwc2 c90c0000.usb:     do_split: 0
[    1.805632] dwc2 c90c0000.usb:     complete_split: 0
[    1.805635] dwc2 c90c0000.usb:     hub_addr: 0
[    1.805639] dwc2 c90c0000.usb:     hub_port: 0
[    1.805642] dwc2 c90c0000.usb:     xact_pos: 0
[    1.805646] dwc2 c90c0000.usb:     requests: 0
[    1.805649] dwc2 c90c0000.usb:     qh:   (null)
[    1.805653] dwc2 c90c0000.usb:   Channel 11:
[    1.805657] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.805661] dwc2 c90c0000.usb:     speed: 0
[    1.805664] dwc2 c90c0000.usb:     ep_type: 0
[    1.805668] dwc2 c90c0000.usb:     max_packet: 0
[    1.805671] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.805675] dwc2 c90c0000.usb:     multi_count: 0
[    1.805678] dwc2 c90c0000.usb:     xfer_started: 0
[    1.805682] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.805685] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.805689] dwc2 c90c0000.usb:     xfer_len: 0
[    1.805693] dwc2 c90c0000.usb:     xfer_count: 0
[    1.805696] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.805700] dwc2 c90c0000.usb:     halt_pending: 0
[    1.805703] dwc2 c90c0000.usb:     halt_status: 0
[    1.805707] dwc2 c90c0000.usb:     do_split: 0
[    1.805710] dwc2 c90c0000.usb:     complete_split: 0
[    1.805714] dwc2 c90c0000.usb:     hub_addr: 0
[    1.805717] dwc2 c90c0000.usb:     hub_port: 0
[    1.805721] dwc2 c90c0000.usb:     xact_pos: 0
[    1.805724] dwc2 c90c0000.usb:     requests: 0
[    1.805728] dwc2 c90c0000.usb:     qh:   (null)
[    1.805731] dwc2 c90c0000.usb:   Channel 12:
[    1.805736] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.805740] dwc2 c90c0000.usb:     speed: 0
[    1.805743] dwc2 c90c0000.usb:     ep_type: 0
[    1.805747] dwc2 c90c0000.usb:     max_packet: 0
[    1.805750] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.805754] dwc2 c90c0000.usb:     multi_count: 0
[    1.805757] dwc2 c90c0000.usb:     xfer_started: 0
[    1.805761] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.805764] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.805768] dwc2 c90c0000.usb:     xfer_len: 0
[    1.805771] dwc2 c90c0000.usb:     xfer_count: 0
[    1.805775] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.805778] dwc2 c90c0000.usb:     halt_pending: 0
[    1.805782] dwc2 c90c0000.usb:     halt_status: 0
[    1.805785] dwc2 c90c0000.usb:     do_split: 0
[    1.805789] dwc2 c90c0000.usb:     complete_split: 0
[    1.805792] dwc2 c90c0000.usb:     hub_addr: 0
[    1.805796] dwc2 c90c0000.usb:     hub_port: 0
[    1.805799] dwc2 c90c0000.usb:     xact_pos: 0
[    1.805803] dwc2 c90c0000.usb:     requests: 0
[    1.805806] dwc2 c90c0000.usb:     qh:   (null)
[    1.805810] dwc2 c90c0000.usb:   Channel 13:
[    1.805814] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.805818] dwc2 c90c0000.usb:     speed: 0
[    1.805821] dwc2 c90c0000.usb:     ep_type: 0
[    1.805825] dwc2 c90c0000.usb:     max_packet: 0
[    1.805828] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.805832] dwc2 c90c0000.usb:     multi_count: 0
[    1.805835] dwc2 c90c0000.usb:     xfer_started: 0
[    1.805839] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.805842] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.805849] dwc2 c90c0000.usb:     xfer_len: 0
[    1.805853] dwc2 c90c0000.usb:     xfer_count: 0
[    1.805856] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.805860] dwc2 c90c0000.usb:     halt_pending: 0
[    1.805863] dwc2 c90c0000.usb:     halt_status: 0
[    1.805867] dwc2 c90c0000.usb:     do_split: 0
[    1.805870] dwc2 c90c0000.usb:     complete_split: 0
[    1.805874] dwc2 c90c0000.usb:     hub_addr: 0
[    1.805877] dwc2 c90c0000.usb:     hub_port: 0
[    1.805881] dwc2 c90c0000.usb:     xact_pos: 0
[    1.805884] dwc2 c90c0000.usb:     requests: 0
[    1.805888] dwc2 c90c0000.usb:     qh:   (null)
[    1.805891] dwc2 c90c0000.usb:   Channel 14:
[    1.805896] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.805901] dwc2 c90c0000.usb:     speed: 0
[    1.805905] dwc2 c90c0000.usb:     ep_type: 0
[    1.805934] dwc2 c90c0000.usb:     max_packet: 0
[    1.805938] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.805942] dwc2 c90c0000.usb:     multi_count: 0
[    1.805946] dwc2 c90c0000.usb:     xfer_started: 0
[    1.805949] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.805953] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.805956] dwc2 c90c0000.usb:     xfer_len: 0
[    1.805960] dwc2 c90c0000.usb:     xfer_count: 0
[    1.805963] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.805967] dwc2 c90c0000.usb:     halt_pending: 0
[    1.805970] dwc2 c90c0000.usb:     halt_status: 0
[    1.805974] dwc2 c90c0000.usb:     do_split: 0
[    1.805977] dwc2 c90c0000.usb:     complete_split: 0
[    1.805981] dwc2 c90c0000.usb:     hub_addr: 0
[    1.805984] dwc2 c90c0000.usb:     hub_port: 0
[    1.805988] dwc2 c90c0000.usb:     xact_pos: 0
[    1.805991] dwc2 c90c0000.usb:     requests: 0
[    1.805995] dwc2 c90c0000.usb:     qh:   (null)
[    1.805999] dwc2 c90c0000.usb:   Channel 15:
[    1.806003] dwc2 c90c0000.usb:     dev_addr: 0, ep_num: 0, ep_is_in: 0
[    1.806007] dwc2 c90c0000.usb:     speed: 0
[    1.806010] dwc2 c90c0000.usb:     ep_type: 0
[    1.806014] dwc2 c90c0000.usb:     max_packet: 0
[    1.806017] dwc2 c90c0000.usb:     data_pid_start: 0
[    1.806021] dwc2 c90c0000.usb:     multi_count: 0
[    1.806024] dwc2 c90c0000.usb:     xfer_started: 0
[    1.806028] dwc2 c90c0000.usb:     xfer_buf:   (null)
[    1.806031] dwc2 c90c0000.usb:     xfer_dma: 00000000
[    1.806035] dwc2 c90c0000.usb:     xfer_len: 0
[    1.806038] dwc2 c90c0000.usb:     xfer_count: 0
[    1.806042] dwc2 c90c0000.usb:     halt_on_queue: 0
[    1.806045] dwc2 c90c0000.usb:     halt_pending: 0
[    1.806049] dwc2 c90c0000.usb:     halt_status: 0
[    1.806052] dwc2 c90c0000.usb:     do_split: 0
[    1.806056] dwc2 c90c0000.usb:     complete_split: 0
[    1.806059] dwc2 c90c0000.usb:     hub_addr: 0
[    1.806063] dwc2 c90c0000.usb:     hub_port: 0
[    1.806066] dwc2 c90c0000.usb:     xact_pos: 0
[    1.806070] dwc2 c90c0000.usb:     requests: 0
[    1.806073] dwc2 c90c0000.usb:     qh:   (null)
[    1.806077] dwc2 c90c0000.usb:   non_periodic_channels: 0
[    1.806081] dwc2 c90c0000.usb:   periodic_channels: 0
[    1.806084] dwc2 c90c0000.usb:   periodic_usecs: 0
[    1.806088] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail: 8
[    1.806092] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail: 500
[    1.806096] dwc2 c90c0000.usb:   P Tx Req Queue Space Avail: 8
[    1.806099] dwc2 c90c0000.usb:   P Tx FIFO Space Avail: 500
[    1.806103] dwc2 c90c0000.usb: Core Global Registers
[    1.806108] dwc2 c90c0000.usb: GOTGCTL	 @0xF0A40000 : 0x02200000
[    1.806112] dwc2 c90c0000.usb: GOTGINT	 @0xF0A40004 : 0x00000000
[    1.806116] dwc2 c90c0000.usb: GAHBCFG	 @0xF0A40008 : 0x0000002A
[    1.806121] dwc2 c90c0000.usb: GUSBCFG	 @0xF0A4000C : 0x0000140F
[    1.806125] dwc2 c90c0000.usb: GRSTCTL	 @0xF0A40010 : 0x80000000
[    1.806129] dwc2 c90c0000.usb: GINTSTS	 @0xF0A40014 : 0x05000021
[    1.806134] dwc2 c90c0000.usb: GINTMSK	 @0xF0A40018 : 0xF3000006
[    1.806138] dwc2 c90c0000.usb: GRXSTSR	 @0xF0A4001C : 0x000E000F
[    1.806142] dwc2 c90c0000.usb: GRXFSIZ	 @0xF0A40024 : 0x00000200
[    1.806146] dwc2 c90c0000.usb: GNPTXFSIZ	 @0xF0A40028 : 0x01F40200
[    1.806151] dwc2 c90c0000.usb: GNPTXSTS	 @0xF0A4002C : 0x470801F4
[    1.806156] dwc2 c90c0000.usb: GI2CCTL	 @0xF0A40030 : 0x00000000
[    1.806160] dwc2 c90c0000.usb: GPVNDCTL	 @0xF0A40034 : 0x00000000
[    1.806164] dwc2 c90c0000.usb: GGPIO	 @0xF0A40038 : 0x00000000
[    1.806168] dwc2 c90c0000.usb: GUID	 @0xF0A4003C : 0x12345678
[    1.806173] dwc2 c90c0000.usb: GSNPSID	 @0xF0A40040 : 0x4F54310A
[    1.806177] dwc2 c90c0000.usb: GHWCFG1	 @0xF0A40044 : 0x00000000
[    1.806181] dwc2 c90c0000.usb: GHWCFG2	 @0xF0A40048 : 0x228FC855
[    1.806185] dwc2 c90c0000.usb: GHWCFG3	 @0xF0A4004C : 0x07C05068
[    1.806189] dwc2 c90c0000.usb: GHWCFG4	 @0xF0A40050 : 0xC9E04030
[    1.806194] dwc2 c90c0000.usb: GLPMCFG	 @0xF0A40054 : 0x00000000
[    1.806198] dwc2 c90c0000.usb: GPWRDN	 @0xF0A40058 : 0x08000010
[    1.806203] dwc2 c90c0000.usb: GDFIFOCFG	 @0xF0A4005C : 0x07C00800
[    1.806207] dwc2 c90c0000.usb: HPTXFSIZ	 @0xF0A40100 : 0x01F403F4
[    1.806211] dwc2 c90c0000.usb: PCGCTL	 @0xF0A40E00 : 0x00000000
[    1.806215] dwc2 c90c0000.usb: Host Global Registers
[    1.806219] dwc2 c90c0000.usb: HCFG	 @0xF0A40400 : 0x00000200
[    1.806223] dwc2 c90c0000.usb: HFIR	 @0xF0A40404 : 0x0001EA60
[    1.806227] dwc2 c90c0000.usb: HFNUM	 @0xF0A40408 : 0xEA603FFF
[    1.806232] dwc2 c90c0000.usb: HPTXSTS	 @0xF0A40410 : 0x000801F4
[    1.806236] dwc2 c90c0000.usb: HAINT	 @0xF0A40414 : 0x00000000
[    1.806240] dwc2 c90c0000.usb: HAINTMSK	 @0xF0A40418 : 0x00000000
[    1.806244] dwc2 c90c0000.usb: HPRT0	 @0xF0A40440 : 0x00021403
[    1.806248] dwc2 c90c0000.usb: Host Channel 0 Specific Registers
[    1.806252] dwc2 c90c0000.usb: HCCHAR	 @0xF0A40500 : 0x00000000
[    1.806257] dwc2 c90c0000.usb: HCSPLT	 @0xF0A40504 : 0x00000000
[    1.806261] dwc2 c90c0000.usb: HCINT	 @0xF0A40508 : 0x00000002
[    1.806265] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A4050C : 0x00000000
[    1.806269] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A40510 : 0x00000000
[    1.806274] dwc2 c90c0000.usb: HCDMA	 @0xF0A40514 : 0xB4C4A0E0
[    1.806277] dwc2 c90c0000.usb: Host Channel 1 Specific Registers
[    1.806281] dwc2 c90c0000.usb: HCCHAR	 @0xF0A40520 : 0x00000000
[    1.806286] dwc2 c90c0000.usb: HCSPLT	 @0xF0A40524 : 0x00000000
[    1.806290] dwc2 c90c0000.usb: HCINT	 @0xF0A40528 : 0x00000002
[    1.806294] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A4052C : 0x00000000
[    1.806298] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A40530 : 0x00000000
[    1.806302] dwc2 c90c0000.usb: HCDMA	 @0xF0A40534 : 0x3950DB42
[    1.806306] dwc2 c90c0000.usb: Host Channel 2 Specific Registers
[    1.806310] dwc2 c90c0000.usb: HCCHAR	 @0xF0A40540 : 0x00000000
[    1.806314] dwc2 c90c0000.usb: HCSPLT	 @0xF0A40544 : 0x00000000
[    1.806319] dwc2 c90c0000.usb: HCINT	 @0xF0A40548 : 0x00000002
[    1.806323] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A4054C : 0x00000000
[    1.806327] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A40550 : 0x00000000
[    1.806331] dwc2 c90c0000.usb: HCDMA	 @0xF0A40554 : 0x41983B05
[    1.806335] dwc2 c90c0000.usb: Host Channel 3 Specific Registers
[    1.806339] dwc2 c90c0000.usb: HCCHAR	 @0xF0A40560 : 0x00000000
[    1.806343] dwc2 c90c0000.usb: HCSPLT	 @0xF0A40564 : 0x00000000
[    1.806348] dwc2 c90c0000.usb: HCINT	 @0xF0A40568 : 0x00000002
[    1.806352] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A4056C : 0x00000000
[    1.806356] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A40570 : 0x00000000
[    1.806360] dwc2 c90c0000.usb: HCDMA	 @0xF0A40574 : 0x35966146
[    1.806364] dwc2 c90c0000.usb: Host Channel 4 Specific Registers
[    1.806368] dwc2 c90c0000.usb: HCCHAR	 @0xF0A40580 : 0x00000000
[    1.806372] dwc2 c90c0000.usb: HCSPLT	 @0xF0A40584 : 0x00000000
[    1.806376] dwc2 c90c0000.usb: HCINT	 @0xF0A40588 : 0x00000002
[    1.806380] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A4058C : 0x00000000
[    1.806385] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A40590 : 0x00000000
[    1.806389] dwc2 c90c0000.usb: HCDMA	 @0xF0A40594 : 0x3B0522D0
[    1.806393] dwc2 c90c0000.usb: Host Channel 5 Specific Registers
[    1.806397] dwc2 c90c0000.usb: HCCHAR	 @0xF0A405A0 : 0x00000000
[    1.806401] dwc2 c90c0000.usb: HCSPLT	 @0xF0A405A4 : 0x00000000
[    1.806405] dwc2 c90c0000.usb: HCINT	 @0xF0A405A8 : 0x00000002
[    1.806409] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A405AC : 0x00000000
[    1.806413] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A405B0 : 0x00000000
[    1.806418] dwc2 c90c0000.usb: HCDMA	 @0xF0A405B4 : 0x325E792E
[    1.806422] dwc2 c90c0000.usb: Host Channel 6 Specific Registers
[    1.806426] dwc2 c90c0000.usb: HCCHAR	 @0xF0A405C0 : 0x00000000
[    1.806430] dwc2 c90c0000.usb: HCSPLT	 @0xF0A405C4 : 0x00000000
[    1.806434] dwc2 c90c0000.usb: HCINT	 @0xF0A405C8 : 0x00000002
[    1.806438] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A405CC : 0x00000000
[    1.806442] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A405D0 : 0x00000000
[    1.806447] dwc2 c90c0000.usb: HCDMA	 @0xF0A405D4 : 0x602B151E
[    1.806450] dwc2 c90c0000.usb: Host Channel 7 Specific Registers
[    1.806455] dwc2 c90c0000.usb: HCCHAR	 @0xF0A405E0 : 0x00000000
[    1.806459] dwc2 c90c0000.usb: HCSPLT	 @0xF0A405E4 : 0x00000000
[    1.806463] dwc2 c90c0000.usb: HCINT	 @0xF0A405E8 : 0x00000002
[    1.806467] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A405EC : 0x00000000
[    1.806471] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A405F0 : 0x00000000
[    1.806475] dwc2 c90c0000.usb: HCDMA	 @0xF0A405F4 : 0xBF3A191A
[    1.806479] dwc2 c90c0000.usb: Host Channel 8 Specific Registers
[    1.806483] dwc2 c90c0000.usb: HCCHAR	 @0xF0A40600 : 0x00000000
[    1.806487] dwc2 c90c0000.usb: HCSPLT	 @0xF0A40604 : 0x00000000
[    1.806491] dwc2 c90c0000.usb: HCINT	 @0xF0A40608 : 0x00000002
[    1.806496] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A4060C : 0x00000000
[    1.806500] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A40610 : 0x00000000
[    1.806504] dwc2 c90c0000.usb: HCDMA	 @0xF0A40614 : 0x38222977
[    1.806508] dwc2 c90c0000.usb: Host Channel 9 Specific Registers
[    1.806512] dwc2 c90c0000.usb: HCCHAR	 @0xF0A40620 : 0x00000000
[    1.806516] dwc2 c90c0000.usb: HCSPLT	 @0xF0A40624 : 0x00000000
[    1.806520] dwc2 c90c0000.usb: HCINT	 @0xF0A40628 : 0x00000002
[    1.806524] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A4062C : 0x00000000
[    1.806528] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A40630 : 0x00000000
[    1.806533] dwc2 c90c0000.usb: HCDMA	 @0xF0A40634 : 0x904F5A1F
[    1.806536] dwc2 c90c0000.usb: Host Channel 10 Specific Registers
[    1.806541] dwc2 c90c0000.usb: HCCHAR	 @0xF0A40640 : 0x00000000
[    1.806545] dwc2 c90c0000.usb: HCSPLT	 @0xF0A40644 : 0x00000000
[    1.806549] dwc2 c90c0000.usb: HCINT	 @0xF0A40648 : 0x00000002
[    1.806553] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A4064C : 0x00000000
[    1.806557] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A40650 : 0x00000000
[    1.806561] dwc2 c90c0000.usb: HCDMA	 @0xF0A40654 : 0x47913889
[    1.806566] dwc2 c90c0000.usb: Host Channel 11 Specific Registers
[    1.806570] dwc2 c90c0000.usb: HCCHAR	 @0xF0A40660 : 0x00000000
[    1.806574] dwc2 c90c0000.usb: HCSPLT	 @0xF0A40664 : 0x00000000
[    1.806578] dwc2 c90c0000.usb: HCINT	 @0xF0A40668 : 0x00000002
[    1.806582] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A4066C : 0x00000000
[    1.806587] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A40670 : 0x00000000
[    1.806591] dwc2 c90c0000.usb: HCDMA	 @0xF0A40674 : 0x5793E812
[    1.806595] dwc2 c90c0000.usb: Host Channel 12 Specific Registers
[    1.806599] dwc2 c90c0000.usb: HCCHAR	 @0xF0A40680 : 0x00000000
[    1.806603] dwc2 c90c0000.usb: HCSPLT	 @0xF0A40684 : 0x00000000
[    1.806607] dwc2 c90c0000.usb: HCINT	 @0xF0A40688 : 0x00000002
[    1.806611] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A4068C : 0x00000000
[    1.806616] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A40690 : 0x00000000
[    1.806620] dwc2 c90c0000.usb: HCDMA	 @0xF0A40694 : 0xB2598021
[    1.806624] dwc2 c90c0000.usb: Host Channel 13 Specific Registers
[    1.806628] dwc2 c90c0000.usb: HCCHAR	 @0xF0A406A0 : 0x00000000
[    1.806632] dwc2 c90c0000.usb: HCSPLT	 @0xF0A406A4 : 0x00000000
[    1.806636] dwc2 c90c0000.usb: HCINT	 @0xF0A406A8 : 0x00000002
[    1.806640] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A406AC : 0x00000000
[    1.806644] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A406B0 : 0x00000000
[    1.806648] dwc2 c90c0000.usb: HCDMA	 @0xF0A406B4 : 0xDE3F669F
[    1.806652] dwc2 c90c0000.usb: Host Channel 14 Specific Registers
[    1.806656] dwc2 c90c0000.usb: HCCHAR	 @0xF0A406C0 : 0x00000000
[    1.806661] dwc2 c90c0000.usb: HCSPLT	 @0xF0A406C4 : 0x00000000
[    1.806665] dwc2 c90c0000.usb: HCINT	 @0xF0A406C8 : 0x00000002
[    1.806669] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A406CC : 0x00000000
[    1.806673] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A406D0 : 0x00000000
[    1.806677] dwc2 c90c0000.usb: HCDMA	 @0xF0A406D4 : 0xF4A3C245
[    1.806681] dwc2 c90c0000.usb: Host Channel 15 Specific Registers
[    1.806685] dwc2 c90c0000.usb: HCCHAR	 @0xF0A406E0 : 0x00000000
[    1.806689] dwc2 c90c0000.usb: HCSPLT	 @0xF0A406E4 : 0x00000000
[    1.806693] dwc2 c90c0000.usb: HCINT	 @0xF0A406E8 : 0x00000002
[    1.806698] dwc2 c90c0000.usb: HCINTMSK	 @0xF0A406EC : 0x00000000
[    1.806702] dwc2 c90c0000.usb: HCTSIZ	 @0xF0A406F0 : 0x00000000
[    1.806706] dwc2 c90c0000.usb: HCDMA	 @0xF0A406F4 : 0xFF321AE9
[    1.806710] dwc2 c90c0000.usb: ************************************************************
[    1.806713] dwc2 c90c0000.usb: 
[    1.806722] dwc2 c90c0000.usb: gintsts=05000021  gintmsk=f3000006
[    1.806728] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x01000000
[    1.806732] dwc2 c90c0000.usb: --Port Interrupt--
[    1.806737] dwc2 c90c0000.usb: --Port Interrupt HPRT0=0x00021403 Port Connect Detected--
[    1.806741] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    1.806745] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf3000006
[    1.808409] platform c1108c20.mmc:slot at 1: Got CD GPIO
[    1.831307] hctosys: unable to open rtc device (rtc0)
[    1.831472] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    1.846891] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    1.847871] TF_IO: disabling
[    1.856548] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    1.859534] cfg80211: failed to load regulatory.db
[    1.866115] Freeing unused kernel memory: 2048K
[    1.905981] dwc2 c90c0000.usb: GetPortStatus wIndex=0x0001 flags=0x00000003
[    1.905989] dwc2 c90c0000.usb:   HPRT0: 0x00021401
[    1.905994] dwc2 c90c0000.usb: port_status=00010101
[    1.906042] dwc2 c90c0000.usb: ClearPortFeature USB_PORT_FEAT_C_CONNECTION
[    1.937767] random: systemd-tmpfile: uninitialized urandom read (16 bytes read)
[    1.948525] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    1.954403] random: udevadm: uninitialized urandom read (16 bytes read)
[    2.016000] dwc2 c90c0000.usb: GetPortStatus wIndex=0x0001 flags=0x00000002
[    2.016008] dwc2 c90c0000.usb:   HPRT0: 0x00021401
[    2.016012] dwc2 c90c0000.usb: port_status=00000101
[    2.016065] dwc2 c90c0000.usb: SetPortFeature
[    2.016070] dwc2 c90c0000.usb: SetPortFeature - USB_PORT_FEAT_RESET
[    2.016075] dwc2 c90c0000.usb: In host mode, hprt0=00021501
[    2.031812] mmc0: new high speed SDHC card at address 0001
[    2.032245] mmcblk0: mmc0:0001 EB1QT 29.8 GiB 
[    2.038325]  mmcblk0: p1 p2
[    2.086238] dwc2 c90c0000.usb: gintsts=05000021  gintmsk=f3000006
[    2.086248] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x01000000
[    2.086252] dwc2 c90c0000.usb: --Port Interrupt--
[    2.086257] dwc2 c90c0000.usb:   --Port Interrupt HPRT0=0x0000100d Port Enable Changed (now 1)--
[    2.086262] dwc2 c90c0000.usb: dwc2_hprt0_enable((ptrval))
[    2.086267] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.086271] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf3000006
[    2.166024] dwc2 c90c0000.usb: GetPortStatus wIndex=0x0001 flags=0x00000006
[    2.166032] dwc2 c90c0000.usb:   HPRT0: 0x00001005
[    2.166037] dwc2 c90c0000.usb: port_status=00100503
[    2.166409] dwc2 c90c0000.usb: ClearPortFeature USB_PORT_FEAT_C_RESET
[    2.196197] random: fast init done
[    2.235997] usb 1-1: new high-speed USB device number 2 using dwc2
[    2.236555] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.236560] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.236564] dwc2 c90c0000.usb:   Device address: 0
[    2.236568] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.236573] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.236576] dwc2 c90c0000.usb:   Speed: HIGH
[    2.236580] dwc2 c90c0000.usb:   Max packet size: 64
[    2.236584] dwc2 c90c0000.usb:   Data buffer length: 64
[    2.236588] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 2e765d00
[    2.236592] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 2e765c80
[    2.236596] dwc2 c90c0000.usb:   Interval: 0
[    2.236602] dwc2 c90c0000.usb: addr=0, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.236610] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.236616] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.236621] dwc2 c90c0000.usb:   Control setup transaction
[    2.236625] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.236629] dwc2 c90c0000.usb: DMA enabled
[    2.236632] dwc2 c90c0000.usb: desc DMA disabled
[    2.236636] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.236640] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[    2.236643] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.236648] dwc2 c90c0000.usb: set HCCHAR(0) to 00000040
[    2.236652] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[    2.236655] dwc2 c90c0000.usb: 	 Dev Addr: 0
[    2.236659] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.236662] dwc2 c90c0000.usb: 	 Is In: 0
[    2.236665] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.236669] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.236672] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.236676] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.236680] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.236684] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.236688] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.236692] dwc2 c90c0000.usb: no split
[    2.236697] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(0)
[    2.236701] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[    2.236704] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.236707] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.236711] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.236715] dwc2 c90c0000.usb: Wrote 2e765c80 to HCDMA(0)
[    2.236719] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.236723] dwc2 c90c0000.usb: Wrote 80100040 to HCCHAR(0)
[    2.236735] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.236738] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.236742] dwc2 c90c0000.usb: HAINT=00000001
[    2.236747] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[    2.236751] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.236755] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Channel Halted--
[    2.236759] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: DMA Channel Halted--
[    2.236764] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Transfer Complete--
[    2.236768] dwc2 c90c0000.usb:   Control setup transaction done
[    2.236771] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.236776] dwc2 c90c0000.usb:   dwc2_release_channel: channel 0, halt_status 1
[    2.236781] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.236785] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.236788] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.236792] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.236797] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.236800] dwc2 c90c0000.usb:   Control data transaction
[    2.236804] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.236807] dwc2 c90c0000.usb: DMA enabled
[    2.236811] dwc2 c90c0000.usb: desc DMA disabled
[    2.236814] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.236818] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[    2.236822] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.236826] dwc2 c90c0000.usb: set HCCHAR(1) to 00008040
[    2.236829] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[    2.236833] dwc2 c90c0000.usb: 	 Dev Addr: 0
[    2.236836] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.236840] dwc2 c90c0000.usb: 	 Is In: 1
[    2.236843] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.236846] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.236850] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.236853] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.236857] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.236861] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.236864] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.236867] dwc2 c90c0000.usb: no split
[    2.236872] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(1)
[    2.236876] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[    2.236879] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.236883] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.236887] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.236891] dwc2 c90c0000.usb: Wrote 2e765d00 to HCDMA(1)
[    2.236894] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.236898] dwc2 c90c0000.usb: Wrote 80108040 to HCCHAR(1)
[    2.236903] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.236907] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.237070] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.237075] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.237079] dwc2 c90c0000.usb: HAINT=00000002
[    2.237083] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[    2.237087] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.237092] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[    2.237095] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[    2.237100] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[    2.237105] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=18
[    2.237109] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 1
[    2.237113] dwc2 c90c0000.usb:   chan->xfer_len 64
[    2.237116] dwc2 c90c0000.usb:   hctsiz.xfersize 46
[    2.237120] dwc2 c90c0000.usb:   urb->transfer_buffer_length 64
[    2.237123] dwc2 c90c0000.usb:   urb->actual_length 18
[    2.237127] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.237131] dwc2 c90c0000.usb:   Control data transfer done
[    2.237134] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.237138] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.237141] dwc2 c90c0000.usb: DMA enabled
[    2.237145] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 1
[    2.237150] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.237153] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.237157] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.237160] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.237165] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.237169] dwc2 c90c0000.usb:   Control status transaction
[    2.237173] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.237177] dwc2 c90c0000.usb: DMA enabled
[    2.237180] dwc2 c90c0000.usb: desc DMA disabled
[    2.237183] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.237187] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[    2.237191] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.237195] dwc2 c90c0000.usb: set HCCHAR(2) to 00000040
[    2.237199] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[    2.237202] dwc2 c90c0000.usb: 	 Dev Addr: 0
[    2.237205] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.237209] dwc2 c90c0000.usb: 	 Is In: 0
[    2.237212] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.237215] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.237219] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.237223] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.237226] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.237230] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.237234] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.237237] dwc2 c90c0000.usb: no split
[    2.237242] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(2)
[    2.237246] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[    2.237249] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.237252] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.237256] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.237260] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(2)
[    2.237264] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.237268] dwc2 c90c0000.usb: Wrote 80100040 to HCCHAR(2)
[    2.237272] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.237276] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf3000006
[    2.237287] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.237290] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.237294] dwc2 c90c0000.usb: HAINT=00000004
[    2.237298] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[    2.237302] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.237306] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[    2.237310] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[    2.237314] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[    2.237317] dwc2 c90c0000.usb:   Control transfer complete
[    2.237323] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 0 ep 0-IN status 0 actual 18
[    2.237329] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.237333] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 2
[    2.237338] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.237341] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.237345] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.237349] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.237354] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.237391] dwc2 c90c0000.usb: SetPortFeature
[    2.237395] dwc2 c90c0000.usb: SetPortFeature - USB_PORT_FEAT_RESET
[    2.237400] dwc2 c90c0000.usb: In host mode, hprt0=00001101
[    2.237407] dwc2 c90c0000.usb: gintsts=05000029  gintmsk=f3000006
[    2.237412] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x01000000
[    2.237416] dwc2 c90c0000.usb: --Port Interrupt--
[    2.237421] dwc2 c90c0000.usb:   --Port Interrupt HPRT0=0x00001109 Port Enable Changed (now 0)--
[    2.237424] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.237429] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.305957] dwc2 c90c0000.usb: DWC OTG HCD HUB STATUS DATA: Root port status changed
[    2.305967] dwc2 c90c0000.usb:   port_connect_status_change: 0
[    2.305971] dwc2 c90c0000.usb:   port_reset_change: 0
[    2.305975] dwc2 c90c0000.usb:   port_enable_change: 1
[    2.305978] dwc2 c90c0000.usb:   port_suspend_change: 0
[    2.305982] dwc2 c90c0000.usb:   port_over_current_change: 0
[    2.306269] dwc2 c90c0000.usb: gintsts=05000029  gintmsk=f3000006
[    2.306278] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x01000000
[    2.306282] dwc2 c90c0000.usb: --Port Interrupt--
[    2.306287] dwc2 c90c0000.usb:   --Port Interrupt HPRT0=0x0000100d Port Enable Changed (now 1)--
[    2.306293] dwc2 c90c0000.usb: dwc2_hprt0_enable((ptrval))
[    2.306297] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.306302] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.386015] dwc2 c90c0000.usb: GetPortStatus wIndex=0x0001 flags=0x0000000e
[    2.386023] dwc2 c90c0000.usb:   HPRT0: 0x00001005
[    2.386027] dwc2 c90c0000.usb: port_status=00120503
[    2.386071] dwc2 c90c0000.usb: ClearPortFeature USB_PORT_FEAT_C_RESET
[    2.455992] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.456000] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.456004] dwc2 c90c0000.usb:   Device address: 0
[    2.456008] dwc2 c90c0000.usb:   Endpoint: 0, OUT
[    2.456013] dwc2 c90c0000.usb:   Endpoint type: CONTROL OUT (OUT)
[    2.456016] dwc2 c90c0000.usb:   Speed: HIGH
[    2.456020] dwc2 c90c0000.usb:   Max packet size: 64
[    2.456024] dwc2 c90c0000.usb:   Data buffer length: 0
[    2.456030] dwc2 c90c0000.usb:   Transfer buffer:   (null), Transfer DMA: 00000000
[    2.456035] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 2e765c40
[    2.456038] dwc2 c90c0000.usb:   Interval: 0
[    2.456044] dwc2 c90c0000.usb: addr=0, ep_num=0, ep_dir=0, ep_type=0, mps=64
[    2.456051] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.456056] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.456062] dwc2 c90c0000.usb:   Control setup transaction
[    2.456066] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.456070] dwc2 c90c0000.usb: DMA enabled
[    2.456073] dwc2 c90c0000.usb: desc DMA disabled
[    2.456077] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.456081] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[    2.456084] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.456088] dwc2 c90c0000.usb: set HCCHAR(3) to 00000040
[    2.456092] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[    2.456096] dwc2 c90c0000.usb: 	 Dev Addr: 0
[    2.456099] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.456102] dwc2 c90c0000.usb: 	 Is In: 0
[    2.456106] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.456109] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.456112] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.456117] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.456120] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.456124] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.456129] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.456132] dwc2 c90c0000.usb: no split
[    2.456138] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(3)
[    2.456142] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[    2.456146] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.456149] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.456152] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.456157] dwc2 c90c0000.usb: Wrote 2e765c40 to HCDMA(3)
[    2.456161] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.456165] dwc2 c90c0000.usb: Wrote 80100040 to HCCHAR(3)
[    2.456185] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.456189] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.456192] dwc2 c90c0000.usb: HAINT=00000008
[    2.456197] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[    2.456201] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.456206] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[    2.456210] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[    2.456214] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[    2.456219] dwc2 c90c0000.usb:   Control setup transaction done
[    2.456223] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.456228] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 1
[    2.456233] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.456237] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.456241] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.456244] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.456249] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.456253] dwc2 c90c0000.usb:   Control status transaction
[    2.456257] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.456260] dwc2 c90c0000.usb: DMA enabled
[    2.456263] dwc2 c90c0000.usb: desc DMA disabled
[    2.456267] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.456271] dwc2 c90c0000.usb: set HAINTMSK to 00000010
[    2.456275] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.456279] dwc2 c90c0000.usb: set HCCHAR(4) to 00008040
[    2.456282] dwc2 c90c0000.usb: dwc2_hc_init: Channel 4
[    2.456286] dwc2 c90c0000.usb: 	 Dev Addr: 0
[    2.456289] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.456293] dwc2 c90c0000.usb: 	 Is In: 1
[    2.456296] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.456299] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.456303] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.456307] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.456310] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.456314] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.456318] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.456321] dwc2 c90c0000.usb: no split
[    2.456326] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(4)
[    2.456330] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 4
[    2.456333] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.456336] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.456340] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.456344] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(4)
[    2.456347] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.456351] dwc2 c90c0000.usb: Wrote 80108040 to HCCHAR(4)
[    2.456356] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.456361] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.456551] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.456556] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.456559] dwc2 c90c0000.usb: HAINT=00000010
[    2.456564] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 4
[    2.456569] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.456573] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Channel Halted--
[    2.456577] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: DMA Channel Halted--
[    2.456581] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Transfer Complete--
[    2.456585] dwc2 c90c0000.usb:   Control transfer complete
[    2.456591] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 0 ep 0-OUT status 0 actual 0
[    2.456597] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.456601] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.456605] dwc2 c90c0000.usb: DMA enabled
[    2.456609] dwc2 c90c0000.usb:   dwc2_release_channel: channel 4, halt_status 2
[    2.456614] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.456617] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.456621] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.456626] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.456631] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.456657] dwc2 c90c0000.usb: DWC OTG HCD EP DISABLE: bEndpointAddress=0x00, ep->hcpriv=(ptrval)
[    2.456662] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.456669] dwc2 c90c0000.usb: DWC OTG HCD EP DISABLE: bEndpointAddress=0x00, ep->hcpriv=  (null)
[    2.456674] dwc2 c90c0000.usb: DWC OTG HCD EP RESET: bEndpointAddress=0x00
[    2.485989] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.485997] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.486002] dwc2 c90c0000.usb:   Device address: 2
[    2.486006] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.486011] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.486014] dwc2 c90c0000.usb:   Speed: HIGH
[    2.486018] dwc2 c90c0000.usb:   Max packet size: 64
[    2.486022] dwc2 c90c0000.usb:   Data buffer length: 18
[    2.486027] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa95780
[    2.486031] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1fa95040
[    2.486035] dwc2 c90c0000.usb:   Interval: 0
[    2.486041] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.486061] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.486067] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.486072] dwc2 c90c0000.usb:   Control setup transaction
[    2.486076] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.486080] dwc2 c90c0000.usb: DMA enabled
[    2.486083] dwc2 c90c0000.usb: desc DMA disabled
[    2.486087] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.486091] dwc2 c90c0000.usb: set HAINTMSK to 00000020
[    2.486095] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.486099] dwc2 c90c0000.usb: set HCCHAR(5) to 00800040
[    2.486103] dwc2 c90c0000.usb: dwc2_hc_init: Channel 5
[    2.486106] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.486110] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.486113] dwc2 c90c0000.usb: 	 Is In: 0
[    2.486117] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.486120] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.486124] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.486128] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.486132] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.486136] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.486141] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.486145] dwc2 c90c0000.usb: no split
[    2.486152] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(5)
[    2.486155] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 5
[    2.486159] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.486162] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.486166] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.486171] dwc2 c90c0000.usb: Wrote 1fa95040 to HCDMA(5)
[    2.486174] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.486179] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(5)
[    2.486190] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.486194] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.486198] dwc2 c90c0000.usb: HAINT=00000020
[    2.486203] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 5
[    2.486207] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.486212] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Channel Halted--
[    2.486216] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: DMA Channel Halted--
[    2.486220] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Transfer Complete--
[    2.486225] dwc2 c90c0000.usb:   Control setup transaction done
[    2.486228] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.486234] dwc2 c90c0000.usb:   dwc2_release_channel: channel 5, halt_status 1
[    2.486239] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.486243] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.486246] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.486250] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.486255] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.486259] dwc2 c90c0000.usb:   Control data transaction
[    2.486262] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.486265] dwc2 c90c0000.usb: DMA enabled
[    2.486269] dwc2 c90c0000.usb: desc DMA disabled
[    2.486272] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.486276] dwc2 c90c0000.usb: set HAINTMSK to 00000040
[    2.486280] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.486284] dwc2 c90c0000.usb: set HCCHAR(6) to 00808040
[    2.486288] dwc2 c90c0000.usb: dwc2_hc_init: Channel 6
[    2.486291] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.486295] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.486299] dwc2 c90c0000.usb: 	 Is In: 1
[    2.486302] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.486305] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.486309] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.486313] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.486316] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.486320] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.486324] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.486327] dwc2 c90c0000.usb: no split
[    2.486332] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(6)
[    2.486336] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 6
[    2.486339] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.486343] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.486346] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.486351] dwc2 c90c0000.usb: Wrote 1fa95780 to HCDMA(6)
[    2.486354] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.486358] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(6)
[    2.486363] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.486367] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.486533] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.486540] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.486544] dwc2 c90c0000.usb: HAINT=00000040
[    2.486549] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 6
[    2.486553] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.486557] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Channel Halted--
[    2.486562] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: DMA Channel Halted--
[    2.486566] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Transfer Complete--
[    2.486572] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=18
[    2.486576] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 6
[    2.486580] dwc2 c90c0000.usb:   chan->xfer_len 64
[    2.486584] dwc2 c90c0000.usb:   hctsiz.xfersize 46
[    2.486587] dwc2 c90c0000.usb:   urb->transfer_buffer_length 18
[    2.486591] dwc2 c90c0000.usb:   urb->actual_length 18
[    2.486594] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.486598] dwc2 c90c0000.usb:   Control data transfer done
[    2.486601] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.486606] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.486609] dwc2 c90c0000.usb: DMA enabled
[    2.486613] dwc2 c90c0000.usb:   dwc2_release_channel: channel 6, halt_status 1
[    2.486618] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.486622] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.486625] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.486629] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.486635] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.486640] dwc2 c90c0000.usb:   Control status transaction
[    2.486644] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.486647] dwc2 c90c0000.usb: DMA enabled
[    2.486650] dwc2 c90c0000.usb: desc DMA disabled
[    2.486654] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.486658] dwc2 c90c0000.usb: set HAINTMSK to 00000080
[    2.486662] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.486666] dwc2 c90c0000.usb: set HCCHAR(7) to 00800040
[    2.486670] dwc2 c90c0000.usb: dwc2_hc_init: Channel 7
[    2.486673] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.486677] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.486680] dwc2 c90c0000.usb: 	 Is In: 0
[    2.486683] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.486687] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.486691] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.486694] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.486698] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.486702] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.486706] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.486710] dwc2 c90c0000.usb: no split
[    2.486714] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(7)
[    2.486718] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 7
[    2.486721] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.486725] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.486728] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.486732] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(7)
[    2.486736] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.486740] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(7)
[    2.486745] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.486749] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf3000006
[    2.486761] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.486764] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.486768] dwc2 c90c0000.usb: HAINT=00000080
[    2.486773] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 7
[    2.486777] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.486781] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Channel Halted--
[    2.486785] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: DMA Channel Halted--
[    2.486789] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Transfer Complete--
[    2.486793] dwc2 c90c0000.usb:   Control transfer complete
[    2.486799] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 18
[    2.486806] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.486811] dwc2 c90c0000.usb:   dwc2_release_channel: channel 7, halt_status 2
[    2.486815] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.486819] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.486822] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.486827] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.486831] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.486916] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.486921] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.486925] dwc2 c90c0000.usb:   Device address: 2
[    2.486929] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.486933] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.486937] dwc2 c90c0000.usb:   Speed: HIGH
[    2.486941] dwc2 c90c0000.usb:   Max packet size: 64
[    2.486945] dwc2 c90c0000.usb:   Data buffer length: 9
[    2.486949] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa87040
[    2.486953] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1fa87080
[    2.486957] dwc2 c90c0000.usb:   Interval: 0
[    2.486963] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.486969] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.486974] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.486979] dwc2 c90c0000.usb:   Control setup transaction
[    2.486982] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.486986] dwc2 c90c0000.usb: DMA enabled
[    2.486989] dwc2 c90c0000.usb: desc DMA disabled
[    2.486993] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.486998] dwc2 c90c0000.usb: set HAINTMSK to 00000100
[    2.487001] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.487006] dwc2 c90c0000.usb: set HCCHAR(8) to 00800040
[    2.487010] dwc2 c90c0000.usb: dwc2_hc_init: Channel 8
[    2.487013] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.487016] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.487020] dwc2 c90c0000.usb: 	 Is In: 0
[    2.487023] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.487027] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.487030] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.487034] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.487038] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.487042] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.487046] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.487049] dwc2 c90c0000.usb: no split
[    2.487054] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(8)
[    2.487058] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 8
[    2.487061] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.487065] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.487068] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.487072] dwc2 c90c0000.usb: Wrote 1fa87080 to HCDMA(8)
[    2.487076] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.487080] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(8)
[    2.487090] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.487093] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.487097] dwc2 c90c0000.usb: HAINT=00000100
[    2.487101] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 8
[    2.487106] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.487110] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Channel Halted--
[    2.487114] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: DMA Channel Halted--
[    2.487119] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Transfer Complete--
[    2.487122] dwc2 c90c0000.usb:   Control setup transaction done
[    2.487126] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.487130] dwc2 c90c0000.usb:   dwc2_release_channel: channel 8, halt_status 1
[    2.487135] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.487138] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.487142] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.487145] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.487150] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.487154] dwc2 c90c0000.usb:   Control data transaction
[    2.487158] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.487161] dwc2 c90c0000.usb: DMA enabled
[    2.487164] dwc2 c90c0000.usb: desc DMA disabled
[    2.487168] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.487172] dwc2 c90c0000.usb: set HAINTMSK to 00000200
[    2.487176] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.487180] dwc2 c90c0000.usb: set HCCHAR(9) to 00808040
[    2.487184] dwc2 c90c0000.usb: dwc2_hc_init: Channel 9
[    2.487187] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.487190] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.487194] dwc2 c90c0000.usb: 	 Is In: 1
[    2.487197] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.487200] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.487204] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.487207] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.487211] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.487215] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.487219] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.487222] dwc2 c90c0000.usb: no split
[    2.487227] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(9)
[    2.487230] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 9
[    2.487234] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.487237] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.487241] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.487245] dwc2 c90c0000.usb: Wrote 1fa87040 to HCDMA(9)
[    2.487248] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.487252] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(9)
[    2.487256] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.487261] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.487447] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.487452] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.487456] dwc2 c90c0000.usb: HAINT=00000200
[    2.487461] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 9
[    2.487466] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.487470] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Channel Halted--
[    2.487474] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: DMA Channel Halted--
[    2.487479] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Transfer Complete--
[    2.487484] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=9
[    2.487489] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 9
[    2.487493] dwc2 c90c0000.usb:   chan->xfer_len 64
[    2.487496] dwc2 c90c0000.usb:   hctsiz.xfersize 55
[    2.487500] dwc2 c90c0000.usb:   urb->transfer_buffer_length 9
[    2.487504] dwc2 c90c0000.usb:   urb->actual_length 9
[    2.487507] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.487511] dwc2 c90c0000.usb:   Control data transfer done
[    2.487514] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.487518] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.487521] dwc2 c90c0000.usb: DMA enabled
[    2.487525] dwc2 c90c0000.usb:   dwc2_release_channel: channel 9, halt_status 1
[    2.487531] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.487534] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.487538] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.487541] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.487547] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.487551] dwc2 c90c0000.usb:   Control status transaction
[    2.487555] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.487558] dwc2 c90c0000.usb: DMA enabled
[    2.487561] dwc2 c90c0000.usb: desc DMA disabled
[    2.487565] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.487569] dwc2 c90c0000.usb: set HAINTMSK to 00000400
[    2.487573] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.487577] dwc2 c90c0000.usb: set HCCHAR(10) to 00800040
[    2.487581] dwc2 c90c0000.usb: dwc2_hc_init: Channel 10
[    2.487584] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.487588] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.487591] dwc2 c90c0000.usb: 	 Is In: 0
[    2.487595] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.487598] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.487602] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.487606] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.487609] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.487613] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.487617] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.487621] dwc2 c90c0000.usb: no split
[    2.487625] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(10)
[    2.487629] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 10
[    2.487633] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.487636] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.487639] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.487644] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(10)
[    2.487647] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.487652] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(10)
[    2.487656] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.487660] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf3000006
[    2.487685] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.487689] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.487693] dwc2 c90c0000.usb: HAINT=00000400
[    2.487697] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 10
[    2.487702] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.487706] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Channel Halted--
[    2.487710] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: DMA Channel Halted--
[    2.487714] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Transfer Complete--
[    2.487718] dwc2 c90c0000.usb:   Control transfer complete
[    2.487723] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 9
[    2.487729] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.487733] dwc2 c90c0000.usb:   dwc2_release_channel: channel 10, halt_status 2
[    2.487738] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.487741] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.487745] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.487749] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.487753] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.487822] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.487836] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.487840] dwc2 c90c0000.usb:   Device address: 2
[    2.487844] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.487848] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.487851] dwc2 c90c0000.usb:   Speed: HIGH
[    2.487855] dwc2 c90c0000.usb:   Max packet size: 64
[    2.487859] dwc2 c90c0000.usb:   Data buffer length: 41
[    2.487863] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa87080
[    2.487867] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1fa87100
[    2.487870] dwc2 c90c0000.usb:   Interval: 0
[    2.487876] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.487882] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.487887] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.487892] dwc2 c90c0000.usb:   Control setup transaction
[    2.487895] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.487899] dwc2 c90c0000.usb: DMA enabled
[    2.487902] dwc2 c90c0000.usb: desc DMA disabled
[    2.487906] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.487910] dwc2 c90c0000.usb: set HAINTMSK to 00000800
[    2.487914] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.487918] dwc2 c90c0000.usb: set HCCHAR(11) to 00800040
[    2.487922] dwc2 c90c0000.usb: dwc2_hc_init: Channel 11
[    2.487925] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.487928] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.487932] dwc2 c90c0000.usb: 	 Is In: 0
[    2.487935] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.487939] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.487943] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.487947] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.487950] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.487954] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.487958] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.487961] dwc2 c90c0000.usb: no split
[    2.487966] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(11)
[    2.487970] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 11
[    2.487973] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.487976] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.487980] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.487984] dwc2 c90c0000.usb: Wrote 1fa87100 to HCDMA(11)
[    2.487988] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.487992] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(11)
[    2.488000] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.488004] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.488007] dwc2 c90c0000.usb: HAINT=00000800
[    2.488012] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 11
[    2.488016] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.488021] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Channel Halted--
[    2.488024] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: DMA Channel Halted--
[    2.488029] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Transfer Complete--
[    2.488033] dwc2 c90c0000.usb:   Control setup transaction done
[    2.488037] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.488041] dwc2 c90c0000.usb:   dwc2_release_channel: channel 11, halt_status 1
[    2.488046] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.488049] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.488053] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.488056] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.488061] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.488065] dwc2 c90c0000.usb:   Control data transaction
[    2.488068] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.488072] dwc2 c90c0000.usb: DMA enabled
[    2.488075] dwc2 c90c0000.usb: desc DMA disabled
[    2.488078] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.488082] dwc2 c90c0000.usb: set HAINTMSK to 00001000
[    2.488086] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.488090] dwc2 c90c0000.usb: set HCCHAR(12) to 00808040
[    2.488094] dwc2 c90c0000.usb: dwc2_hc_init: Channel 12
[    2.488097] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.488101] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.488104] dwc2 c90c0000.usb: 	 Is In: 1
[    2.488107] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.488111] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.488114] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.488118] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.488121] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.488125] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.488129] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.488132] dwc2 c90c0000.usb: no split
[    2.488137] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(12)
[    2.488140] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 12
[    2.488144] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.488147] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.488151] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.488155] dwc2 c90c0000.usb: Wrote 1fa87080 to HCDMA(12)
[    2.488158] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.488162] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(12)
[    2.488167] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.488171] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.488452] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.488459] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.488462] dwc2 c90c0000.usb: HAINT=00001000
[    2.488468] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 12
[    2.488472] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.488477] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Channel Halted--
[    2.488481] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: DMA Channel Halted--
[    2.488485] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Transfer Complete--
[    2.488491] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=41
[    2.488496] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 12
[    2.488499] dwc2 c90c0000.usb:   chan->xfer_len 64
[    2.488503] dwc2 c90c0000.usb:   hctsiz.xfersize 23
[    2.488506] dwc2 c90c0000.usb:   urb->transfer_buffer_length 41
[    2.488510] dwc2 c90c0000.usb:   urb->actual_length 41
[    2.488513] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.488517] dwc2 c90c0000.usb:   Control data transfer done
[    2.488520] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.488524] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.488527] dwc2 c90c0000.usb: DMA enabled
[    2.488532] dwc2 c90c0000.usb:   dwc2_release_channel: channel 12, halt_status 1
[    2.488536] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.488540] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.488544] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.488547] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.488553] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.488557] dwc2 c90c0000.usb:   Control status transaction
[    2.488561] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.488564] dwc2 c90c0000.usb: DMA enabled
[    2.488567] dwc2 c90c0000.usb: desc DMA disabled
[    2.488571] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.488575] dwc2 c90c0000.usb: set HAINTMSK to 00002000
[    2.488579] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.488583] dwc2 c90c0000.usb: set HCCHAR(13) to 00800040
[    2.488587] dwc2 c90c0000.usb: dwc2_hc_init: Channel 13
[    2.488590] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.488594] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.488597] dwc2 c90c0000.usb: 	 Is In: 0
[    2.488601] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.488604] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.488607] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.488611] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.488615] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.488619] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.488623] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.488626] dwc2 c90c0000.usb: no split
[    2.488631] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(13)
[    2.488635] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 13
[    2.488638] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.488641] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.488645] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.488649] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(13)
[    2.488653] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.488657] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(13)
[    2.488662] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.488666] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf3000006
[    2.488689] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.488694] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.488697] dwc2 c90c0000.usb: HAINT=00002000
[    2.488701] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 13
[    2.488706] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.488710] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Channel Halted--
[    2.488714] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: DMA Channel Halted--
[    2.488718] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Transfer Complete--
[    2.488722] dwc2 c90c0000.usb:   Control transfer complete
[    2.488728] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 41
[    2.488734] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.488739] dwc2 c90c0000.usb:   dwc2_release_channel: channel 13, halt_status 2
[    2.488743] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.488747] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.488751] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.488755] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.488760] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.488839] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.488845] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.488849] dwc2 c90c0000.usb:   Device address: 2
[    2.488853] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.488857] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.488860] dwc2 c90c0000.usb:   Speed: HIGH
[    2.488864] dwc2 c90c0000.usb:   Max packet size: 64
[    2.488867] dwc2 c90c0000.usb:   Data buffer length: 255
[    2.488871] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 2e6eea00
[    2.488876] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1fa87040
[    2.488879] dwc2 c90c0000.usb:   Interval: 0
[    2.488886] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.488892] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.488898] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.488902] dwc2 c90c0000.usb:   Control setup transaction
[    2.488906] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.488910] dwc2 c90c0000.usb: DMA enabled
[    2.488913] dwc2 c90c0000.usb: desc DMA disabled
[    2.488917] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.488921] dwc2 c90c0000.usb: set HAINTMSK to 00004000
[    2.488924] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.488929] dwc2 c90c0000.usb: set HCCHAR(14) to 00800040
[    2.488933] dwc2 c90c0000.usb: dwc2_hc_init: Channel 14
[    2.488936] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.488939] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.488943] dwc2 c90c0000.usb: 	 Is In: 0
[    2.488946] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.488950] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.488953] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.488957] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.488961] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.488965] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.488970] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.488973] dwc2 c90c0000.usb: no split
[    2.488979] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(14)
[    2.488982] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 14
[    2.488986] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.488989] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.488993] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.488997] dwc2 c90c0000.usb: Wrote 1fa87040 to HCDMA(14)
[    2.489001] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.489005] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(14)
[    2.489014] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.489018] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.489022] dwc2 c90c0000.usb: HAINT=00004000
[    2.489026] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 14
[    2.489031] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.489035] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Channel Halted--
[    2.489039] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: DMA Channel Halted--
[    2.489043] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Transfer Complete--
[    2.489047] dwc2 c90c0000.usb:   Control setup transaction done
[    2.489051] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.489055] dwc2 c90c0000.usb:   dwc2_release_channel: channel 14, halt_status 1
[    2.489060] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.489063] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.489067] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.489071] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.489076] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.489080] dwc2 c90c0000.usb:   Control data transaction
[    2.489083] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.489086] dwc2 c90c0000.usb: DMA enabled
[    2.489090] dwc2 c90c0000.usb: desc DMA disabled
[    2.489093] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.489098] dwc2 c90c0000.usb: set HAINTMSK to 00008000
[    2.489102] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.489106] dwc2 c90c0000.usb: set HCCHAR(15) to 00808040
[    2.489110] dwc2 c90c0000.usb: dwc2_hc_init: Channel 15
[    2.489113] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.489116] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.489120] dwc2 c90c0000.usb: 	 Is In: 1
[    2.489123] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.489127] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.489130] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.489134] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.489137] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.489141] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.489145] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.489149] dwc2 c90c0000.usb: no split
[    2.489153] dwc2 c90c0000.usb: Wrote 40200100 to HCTSIZ(15)
[    2.489158] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 15
[    2.489162] dwc2 c90c0000.usb: 	 Xfer Size: 256
[    2.489165] dwc2 c90c0000.usb: 	 Num Pkts: 4
[    2.489168] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.489172] dwc2 c90c0000.usb: Wrote 2e6eea00 to HCDMA(15)
[    2.489176] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.489180] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(15)
[    2.489185] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.489189] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.489409] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.489414] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.489418] dwc2 c90c0000.usb: HAINT=00008000
[    2.489423] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 15
[    2.489427] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.489432] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Channel Halted--
[    2.489435] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: DMA Channel Halted--
[    2.489440] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Transfer Complete--
[    2.489445] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4
[    2.489450] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 15
[    2.489453] dwc2 c90c0000.usb:   chan->xfer_len 256
[    2.489456] dwc2 c90c0000.usb:   hctsiz.xfersize 252
[    2.489460] dwc2 c90c0000.usb:   urb->transfer_buffer_length 255
[    2.489463] dwc2 c90c0000.usb:   urb->actual_length 4
[    2.489467] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.489471] dwc2 c90c0000.usb:   Control data transfer done
[    2.489474] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.489478] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.489481] dwc2 c90c0000.usb: DMA enabled
[    2.489486] dwc2 c90c0000.usb:   dwc2_release_channel: channel 15, halt_status 1
[    2.489491] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.489494] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.489498] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.489501] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.489507] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.489512] dwc2 c90c0000.usb:   Control status transaction
[    2.489516] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.489519] dwc2 c90c0000.usb: DMA enabled
[    2.489522] dwc2 c90c0000.usb: desc DMA disabled
[    2.489526] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.489530] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[    2.489533] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.489538] dwc2 c90c0000.usb: set HCCHAR(0) to 00800040
[    2.489541] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[    2.489545] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.489548] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.489551] dwc2 c90c0000.usb: 	 Is In: 0
[    2.489555] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.489558] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.489561] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.489565] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.489569] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.489573] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.489577] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.489580] dwc2 c90c0000.usb: no split
[    2.489585] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(0)
[    2.489589] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[    2.489592] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.489595] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.489599] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.489603] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(0)
[    2.489607] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.489611] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(0)
[    2.489616] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.489620] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf3000006
[    2.489630] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.489633] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.489637] dwc2 c90c0000.usb: HAINT=00000001
[    2.489641] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[    2.489645] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.489649] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Channel Halted--
[    2.489653] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: DMA Channel Halted--
[    2.489657] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Transfer Complete--
[    2.489661] dwc2 c90c0000.usb:   Control transfer complete
[    2.489667] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 4
[    2.489672] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.489677] dwc2 c90c0000.usb:   dwc2_release_channel: channel 0, halt_status 2
[    2.489681] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.489685] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.489688] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.489693] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.489698] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.489764] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.489797] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.489802] dwc2 c90c0000.usb:   Device address: 2
[    2.489806] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.489810] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.489814] dwc2 c90c0000.usb:   Speed: HIGH
[    2.489818] dwc2 c90c0000.usb:   Max packet size: 64
[    2.489822] dwc2 c90c0000.usb:   Data buffer length: 255
[    2.489826] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 2e6eea00
[    2.489831] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1fa87040
[    2.489834] dwc2 c90c0000.usb:   Interval: 0
[    2.489840] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.489845] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.489850] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.489855] dwc2 c90c0000.usb:   Control setup transaction
[    2.489859] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.489862] dwc2 c90c0000.usb: DMA enabled
[    2.489865] dwc2 c90c0000.usb: desc DMA disabled
[    2.489869] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.489873] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[    2.489877] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.489881] dwc2 c90c0000.usb: set HCCHAR(1) to 00800040
[    2.489885] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[    2.489888] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.489892] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.489895] dwc2 c90c0000.usb: 	 Is In: 0
[    2.489898] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.489902] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.489905] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.489909] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.489913] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.489916] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.489921] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.489924] dwc2 c90c0000.usb: no split
[    2.489929] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(1)
[    2.489932] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[    2.489936] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.489939] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.489942] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.489947] dwc2 c90c0000.usb: Wrote 1fa87040 to HCDMA(1)
[    2.489950] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.489954] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(1)
[    2.489963] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.489966] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.489970] dwc2 c90c0000.usb: HAINT=00000002
[    2.489974] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[    2.489978] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.489982] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[    2.489986] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[    2.489991] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[    2.489995] dwc2 c90c0000.usb:   Control setup transaction done
[    2.489998] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.490002] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 1
[    2.490007] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.490011] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.490014] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.490018] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.490022] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.490026] dwc2 c90c0000.usb:   Control data transaction
[    2.490029] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.490032] dwc2 c90c0000.usb: DMA enabled
[    2.490036] dwc2 c90c0000.usb: desc DMA disabled
[    2.490039] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.490043] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[    2.490047] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.490051] dwc2 c90c0000.usb: set HCCHAR(2) to 00808040
[    2.490055] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[    2.490058] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.490061] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.490065] dwc2 c90c0000.usb: 	 Is In: 1
[    2.490068] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.490071] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.490075] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.490079] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.490082] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.490086] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.490090] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.490093] dwc2 c90c0000.usb: no split
[    2.490098] dwc2 c90c0000.usb: Wrote 40200100 to HCTSIZ(2)
[    2.490101] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[    2.490105] dwc2 c90c0000.usb: 	 Xfer Size: 256
[    2.490108] dwc2 c90c0000.usb: 	 Num Pkts: 4
[    2.490111] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.490115] dwc2 c90c0000.usb: Wrote 2e6eea00 to HCDMA(2)
[    2.490119] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.490123] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(2)
[    2.490127] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.490132] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.490387] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.490392] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.490396] dwc2 c90c0000.usb: HAINT=00000004
[    2.490401] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[    2.490405] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.490410] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[    2.490414] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[    2.490419] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[    2.490424] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=22
[    2.490428] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 2
[    2.490432] dwc2 c90c0000.usb:   chan->xfer_len 256
[    2.490436] dwc2 c90c0000.usb:   hctsiz.xfersize 234
[    2.490439] dwc2 c90c0000.usb:   urb->transfer_buffer_length 255
[    2.490443] dwc2 c90c0000.usb:   urb->actual_length 22
[    2.490447] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.490450] dwc2 c90c0000.usb:   Control data transfer done
[    2.490454] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.490458] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.490461] dwc2 c90c0000.usb: DMA enabled
[    2.490465] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 1
[    2.490471] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.490474] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.490478] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.490482] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.490488] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.490492] dwc2 c90c0000.usb:   Control status transaction
[    2.490496] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.490499] dwc2 c90c0000.usb: DMA enabled
[    2.490503] dwc2 c90c0000.usb: desc DMA disabled
[    2.490507] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.490511] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[    2.490514] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.490519] dwc2 c90c0000.usb: set HCCHAR(3) to 00800040
[    2.490522] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[    2.490526] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.490529] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.490532] dwc2 c90c0000.usb: 	 Is In: 0
[    2.490536] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.490539] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.490543] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.490547] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.490550] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.490554] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.490558] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.490562] dwc2 c90c0000.usb: no split
[    2.490566] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(3)
[    2.490570] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[    2.490574] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.490577] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.490580] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.490585] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(3)
[    2.490588] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.490593] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(3)
[    2.490597] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.490601] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf3000006
[    2.490623] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.490627] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.490630] dwc2 c90c0000.usb: HAINT=00000008
[    2.490635] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[    2.490639] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.490644] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[    2.490648] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[    2.490652] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[    2.490655] dwc2 c90c0000.usb:   Control transfer complete
[    2.490661] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 22
[    2.490667] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.490672] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 2
[    2.490676] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.490680] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.490683] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.490688] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.490692] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.491278] dwc2 c90c0000.usb: DWC OTG HCD EP RESET: bEndpointAddress=0x81
[    2.491304] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.491309] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.491313] dwc2 c90c0000.usb:   Device address: 2
[    2.491317] dwc2 c90c0000.usb:   Endpoint: 0, OUT
[    2.491321] dwc2 c90c0000.usb:   Endpoint type: CONTROL OUT (OUT)
[    2.491325] dwc2 c90c0000.usb:   Speed: HIGH
[    2.491329] dwc2 c90c0000.usb:   Max packet size: 64
[    2.491333] dwc2 c90c0000.usb:   Data buffer length: 0
[    2.491338] dwc2 c90c0000.usb:   Transfer buffer:   (null), Transfer DMA: 00000000
[    2.491343] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1fa872c0
[    2.491361] dwc2 c90c0000.usb:   Interval: 0
[    2.491368] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=0, ep_type=0, mps=64
[    2.491374] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.491380] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.491385] dwc2 c90c0000.usb:   Control setup transaction
[    2.491389] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.491392] dwc2 c90c0000.usb: DMA enabled
[    2.491396] dwc2 c90c0000.usb: desc DMA disabled
[    2.491400] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.491404] dwc2 c90c0000.usb: set HAINTMSK to 00000010
[    2.491408] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.491412] dwc2 c90c0000.usb: set HCCHAR(4) to 00800040
[    2.491416] dwc2 c90c0000.usb: dwc2_hc_init: Channel 4
[    2.491419] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.491422] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.491426] dwc2 c90c0000.usb: 	 Is In: 0
[    2.491429] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.491432] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.491436] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.491440] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.491444] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.491448] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.491452] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.491456] dwc2 c90c0000.usb: no split
[    2.491461] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(4)
[    2.491465] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 4
[    2.491468] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.491471] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.491475] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.491480] dwc2 c90c0000.usb: Wrote 1fa872c0 to HCDMA(4)
[    2.491484] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.491488] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(4)
[    2.491497] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.491501] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.491505] dwc2 c90c0000.usb: HAINT=00000010
[    2.491510] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 4
[    2.491514] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.491518] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Channel Halted--
[    2.491522] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: DMA Channel Halted--
[    2.491527] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Transfer Complete--
[    2.491531] dwc2 c90c0000.usb:   Control setup transaction done
[    2.491535] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.491539] dwc2 c90c0000.usb:   dwc2_release_channel: channel 4, halt_status 1
[    2.491544] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.491548] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.491551] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.491555] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.491560] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.491564] dwc2 c90c0000.usb:   Control status transaction
[    2.491568] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.491571] dwc2 c90c0000.usb: DMA enabled
[    2.491574] dwc2 c90c0000.usb: desc DMA disabled
[    2.491578] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.491582] dwc2 c90c0000.usb: set HAINTMSK to 00000020
[    2.491585] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.491590] dwc2 c90c0000.usb: set HCCHAR(5) to 00808040
[    2.491593] dwc2 c90c0000.usb: dwc2_hc_init: Channel 5
[    2.491597] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.491600] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.491604] dwc2 c90c0000.usb: 	 Is In: 1
[    2.491607] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.491610] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.491614] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.491617] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.491621] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.491625] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.491628] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.491632] dwc2 c90c0000.usb: no split
[    2.491636] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(5)
[    2.491640] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 5
[    2.491643] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.491647] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.491650] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.491654] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(5)
[    2.491658] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.491662] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(5)
[    2.491667] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.491671] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.491856] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.491862] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.491866] dwc2 c90c0000.usb: HAINT=00000020
[    2.491871] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 5
[    2.491875] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.491880] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Channel Halted--
[    2.491884] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: DMA Channel Halted--
[    2.491888] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Transfer Complete--
[    2.491892] dwc2 c90c0000.usb:   Control transfer complete
[    2.491898] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-OUT status 0 actual 0
[    2.491904] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.491908] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.491911] dwc2 c90c0000.usb: DMA enabled
[    2.491916] dwc2 c90c0000.usb:   dwc2_release_channel: channel 5, halt_status 2
[    2.491920] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.491924] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.491928] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.491933] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.491938] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.492167] hub 1-1:1.0: USB hub found
[    2.492224] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.492230] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.492234] dwc2 c90c0000.usb:   Device address: 2
[    2.492238] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.492242] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.492246] dwc2 c90c0000.usb:   Speed: HIGH
[    2.492249] dwc2 c90c0000.usb:   Max packet size: 64
[    2.492253] dwc2 c90c0000.usb:   Data buffer length: 15
[    2.492258] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa87440
[    2.492262] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1fa87480
[    2.492266] dwc2 c90c0000.usb:   Interval: 0
[    2.492273] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.492279] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.492285] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.492290] dwc2 c90c0000.usb:   Control setup transaction
[    2.492294] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.492297] dwc2 c90c0000.usb: DMA enabled
[    2.492301] dwc2 c90c0000.usb: desc DMA disabled
[    2.492304] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.492308] dwc2 c90c0000.usb: set HAINTMSK to 00000040
[    2.492312] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.492316] dwc2 c90c0000.usb: set HCCHAR(6) to 00800040
[    2.492320] dwc2 c90c0000.usb: dwc2_hc_init: Channel 6
[    2.492323] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.492327] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.492330] dwc2 c90c0000.usb: 	 Is In: 0
[    2.492334] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.492337] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.492341] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.492344] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.492348] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.492352] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.492357] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.492360] dwc2 c90c0000.usb: no split
[    2.492365] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(6)
[    2.492369] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 6
[    2.492373] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.492376] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.492380] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.492384] dwc2 c90c0000.usb: Wrote 1fa87480 to HCDMA(6)
[    2.492387] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.492392] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(6)
[    2.492402] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.492405] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.492409] dwc2 c90c0000.usb: HAINT=00000040
[    2.492414] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 6
[    2.492419] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.492423] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Channel Halted--
[    2.492427] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: DMA Channel Halted--
[    2.492431] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Transfer Complete--
[    2.492435] dwc2 c90c0000.usb:   Control setup transaction done
[    2.492439] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.492443] dwc2 c90c0000.usb:   dwc2_release_channel: channel 6, halt_status 1
[    2.492448] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.492451] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.492455] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.492458] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.492463] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.492467] dwc2 c90c0000.usb:   Control data transaction
[    2.492470] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.492473] dwc2 c90c0000.usb: DMA enabled
[    2.492477] dwc2 c90c0000.usb: desc DMA disabled
[    2.492480] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.492484] dwc2 c90c0000.usb: set HAINTMSK to 00000080
[    2.492488] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.492492] dwc2 c90c0000.usb: set HCCHAR(7) to 00808040
[    2.492496] dwc2 c90c0000.usb: dwc2_hc_init: Channel 7
[    2.492499] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.492502] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.492506] dwc2 c90c0000.usb: 	 Is In: 1
[    2.492509] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.492513] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.492516] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.492520] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.492524] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.492527] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.492531] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.492535] dwc2 c90c0000.usb: no split
[    2.492539] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(7)
[    2.492543] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 7
[    2.492546] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.492550] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.492553] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.492557] dwc2 c90c0000.usb: Wrote 1fa87440 to HCDMA(7)
[    2.492561] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.492565] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(7)
[    2.492569] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.492574] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.492820] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.492826] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.492829] dwc2 c90c0000.usb: HAINT=00000080
[    2.492834] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 7
[    2.492839] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.492843] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Channel Halted--
[    2.492847] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: DMA Channel Halted--
[    2.492851] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Transfer Complete--
[    2.492857] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=9
[    2.492862] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 7
[    2.492865] dwc2 c90c0000.usb:   chan->xfer_len 64
[    2.492869] dwc2 c90c0000.usb:   hctsiz.xfersize 55
[    2.492873] dwc2 c90c0000.usb:   urb->transfer_buffer_length 15
[    2.492876] dwc2 c90c0000.usb:   urb->actual_length 9
[    2.492880] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.492884] dwc2 c90c0000.usb:   Control data transfer done
[    2.492887] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.492891] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.492894] dwc2 c90c0000.usb: DMA enabled
[    2.492898] dwc2 c90c0000.usb:   dwc2_release_channel: channel 7, halt_status 1
[    2.492903] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.492907] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.492911] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.492914] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.492920] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.492924] dwc2 c90c0000.usb:   Control status transaction
[    2.492929] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.492932] dwc2 c90c0000.usb: DMA enabled
[    2.492935] dwc2 c90c0000.usb: desc DMA disabled
[    2.492939] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.492943] dwc2 c90c0000.usb: set HAINTMSK to 00000100
[    2.492947] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.492951] dwc2 c90c0000.usb: set HCCHAR(8) to 00800040
[    2.492955] dwc2 c90c0000.usb: dwc2_hc_init: Channel 8
[    2.492958] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.492961] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.492965] dwc2 c90c0000.usb: 	 Is In: 0
[    2.492968] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.492972] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.492975] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.492979] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.492982] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.492986] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.492990] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.492994] dwc2 c90c0000.usb: no split
[    2.492999] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(8)
[    2.493002] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 8
[    2.493006] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.493009] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.493012] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.493016] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(8)
[    2.493020] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.493025] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(8)
[    2.493029] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.493034] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf3000006
[    2.493044] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.493048] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.493051] dwc2 c90c0000.usb: HAINT=00000100
[    2.493055] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 8
[    2.493060] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.493064] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Channel Halted--
[    2.493068] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: DMA Channel Halted--
[    2.493072] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Transfer Complete--
[    2.493076] dwc2 c90c0000.usb:   Control transfer complete
[    2.493081] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 9
[    2.493088] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.493092] dwc2 c90c0000.usb:   dwc2_release_channel: channel 8, halt_status 2
[    2.493096] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.493100] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.493103] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.493108] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.493112] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.493178] hub 1-1:1.0: 4 ports detected
[    2.494327] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.494332] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.494336] dwc2 c90c0000.usb:   Device address: 2
[    2.494340] dwc2 c90c0000.usb:   Endpoint: 0, OUT
[    2.494344] dwc2 c90c0000.usb:   Endpoint type: CONTROL OUT (OUT)
[    2.494348] dwc2 c90c0000.usb:   Speed: HIGH
[    2.494351] dwc2 c90c0000.usb:   Max packet size: 64
[    2.494355] dwc2 c90c0000.usb:   Data buffer length: 0
[    2.494361] dwc2 c90c0000.usb:   Transfer buffer:   (null), Transfer DMA: 00000000
[    2.494365] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1fa87500
[    2.494368] dwc2 c90c0000.usb:   Interval: 0
[    2.494374] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=0, ep_type=0, mps=64
[    2.494380] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.494385] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.494390] dwc2 c90c0000.usb:   Control setup transaction
[    2.494394] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.494397] dwc2 c90c0000.usb: DMA enabled
[    2.494400] dwc2 c90c0000.usb: desc DMA disabled
[    2.494404] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.494408] dwc2 c90c0000.usb: set HAINTMSK to 00000200
[    2.494412] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.494416] dwc2 c90c0000.usb: set HCCHAR(9) to 00800040
[    2.494420] dwc2 c90c0000.usb: dwc2_hc_init: Channel 9
[    2.494423] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.494427] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.494430] dwc2 c90c0000.usb: 	 Is In: 0
[    2.494433] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.494437] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.494440] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.494445] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.494448] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.494452] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.494457] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.494460] dwc2 c90c0000.usb: no split
[    2.494465] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(9)
[    2.494469] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 9
[    2.494473] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.494476] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.494479] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.494484] dwc2 c90c0000.usb: Wrote 1fa87500 to HCDMA(9)
[    2.494488] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.494492] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(9)
[    2.494502] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.494505] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.494509] dwc2 c90c0000.usb: HAINT=00000200
[    2.494513] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 9
[    2.494518] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.494522] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Channel Halted--
[    2.494526] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: DMA Channel Halted--
[    2.494531] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Transfer Complete--
[    2.494535] dwc2 c90c0000.usb:   Control setup transaction done
[    2.494538] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.494543] dwc2 c90c0000.usb:   dwc2_release_channel: channel 9, halt_status 1
[    2.494547] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.494551] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.494554] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.494558] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.494563] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.494567] dwc2 c90c0000.usb:   Control status transaction
[    2.494570] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.494573] dwc2 c90c0000.usb: DMA enabled
[    2.494577] dwc2 c90c0000.usb: desc DMA disabled
[    2.494580] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.494584] dwc2 c90c0000.usb: set HAINTMSK to 00000400
[    2.494588] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.494592] dwc2 c90c0000.usb: set HCCHAR(10) to 00808040
[    2.494596] dwc2 c90c0000.usb: dwc2_hc_init: Channel 10
[    2.494599] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.494603] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.494606] dwc2 c90c0000.usb: 	 Is In: 1
[    2.494610] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.494613] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.494616] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.494620] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.494624] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.494628] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.494632] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.494635] dwc2 c90c0000.usb: no split
[    2.494639] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(10)
[    2.494643] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 10
[    2.494647] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.494650] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.494653] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.494657] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(10)
[    2.494661] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.494665] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(10)
[    2.494670] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.494674] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.494863] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.494869] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.494872] dwc2 c90c0000.usb: HAINT=00000400
[    2.494877] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 10
[    2.494882] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.494887] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Channel Halted--
[    2.494891] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: DMA Channel Halted--
[    2.494895] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Transfer Complete--
[    2.494899] dwc2 c90c0000.usb:   Control transfer complete
[    2.494906] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-OUT status 0 actual 0
[    2.494913] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.494917] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.494921] dwc2 c90c0000.usb: DMA enabled
[    2.494925] dwc2 c90c0000.usb:   dwc2_release_channel: channel 10, halt_status 2
[    2.494929] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.494933] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.494937] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.494943] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.494948] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.494986] dwc2 c90c0000.usb: DWC OTG HCD EP DISABLE: bEndpointAddress=0x81, ep->hcpriv=  (null)
[    2.494993] dwc2 c90c0000.usb: DWC OTG HCD EP RESET: bEndpointAddress=0x81
[    2.495064] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.495070] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.495074] dwc2 c90c0000.usb:   Device address: 2
[    2.495078] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.495081] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.495085] dwc2 c90c0000.usb:   Speed: HIGH
[    2.495089] dwc2 c90c0000.usb:   Max packet size: 64
[    2.495092] dwc2 c90c0000.usb:   Data buffer length: 2
[    2.495096] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa874c0
[    2.495100] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1fa87580
[    2.495104] dwc2 c90c0000.usb:   Interval: 0
[    2.495110] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.495116] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.495120] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.495126] dwc2 c90c0000.usb:   Control setup transaction
[    2.495130] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.495133] dwc2 c90c0000.usb: DMA enabled
[    2.495136] dwc2 c90c0000.usb: desc DMA disabled
[    2.495140] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.495144] dwc2 c90c0000.usb: set HAINTMSK to 00000800
[    2.495148] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.495153] dwc2 c90c0000.usb: set HCCHAR(11) to 00800040
[    2.495156] dwc2 c90c0000.usb: dwc2_hc_init: Channel 11
[    2.495160] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.495163] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.495167] dwc2 c90c0000.usb: 	 Is In: 0
[    2.495170] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.495173] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.495177] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.495181] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.495185] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.495188] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.495193] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.495196] dwc2 c90c0000.usb: no split
[    2.495201] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(11)
[    2.495205] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 11
[    2.495209] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.495212] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.495216] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.495221] dwc2 c90c0000.usb: Wrote 1fa87580 to HCDMA(11)
[    2.495224] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.495229] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(11)
[    2.495241] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.495245] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.495248] dwc2 c90c0000.usb: HAINT=00000800
[    2.495252] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 11
[    2.495257] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.495261] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Channel Halted--
[    2.495265] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: DMA Channel Halted--
[    2.495269] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Transfer Complete--
[    2.495273] dwc2 c90c0000.usb:   Control setup transaction done
[    2.495276] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.495281] dwc2 c90c0000.usb:   dwc2_release_channel: channel 11, halt_status 1
[    2.495285] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.495289] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.495292] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.495295] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.495300] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.495304] dwc2 c90c0000.usb:   Control data transaction
[    2.495307] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.495310] dwc2 c90c0000.usb: DMA enabled
[    2.495314] dwc2 c90c0000.usb: desc DMA disabled
[    2.495317] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.495321] dwc2 c90c0000.usb: set HAINTMSK to 00001000
[    2.495325] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.495329] dwc2 c90c0000.usb: set HCCHAR(12) to 00808040
[    2.495332] dwc2 c90c0000.usb: dwc2_hc_init: Channel 12
[    2.495336] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.495339] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.495343] dwc2 c90c0000.usb: 	 Is In: 1
[    2.495346] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.495349] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.495353] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.495356] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.495360] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.495364] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.495368] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.495371] dwc2 c90c0000.usb: no split
[    2.495375] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(12)
[    2.495379] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 12
[    2.495383] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.495386] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.495389] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.495393] dwc2 c90c0000.usb: Wrote 1fa874c0 to HCDMA(12)
[    2.495397] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.495401] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(12)
[    2.495405] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.495410] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.495476] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.495481] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.495484] dwc2 c90c0000.usb: HAINT=00001000
[    2.495489] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 12
[    2.495493] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.495497] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Channel Halted--
[    2.495502] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: DMA Channel Halted--
[    2.495506] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Transfer Complete--
[    2.495511] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=2
[    2.495516] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 12
[    2.495520] dwc2 c90c0000.usb:   chan->xfer_len 64
[    2.495523] dwc2 c90c0000.usb:   hctsiz.xfersize 62
[    2.495527] dwc2 c90c0000.usb:   urb->transfer_buffer_length 2
[    2.495530] dwc2 c90c0000.usb:   urb->actual_length 2
[    2.495534] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.495537] dwc2 c90c0000.usb:   Control data transfer done
[    2.495541] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.495544] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.495547] dwc2 c90c0000.usb: DMA enabled
[    2.495552] dwc2 c90c0000.usb:   dwc2_release_channel: channel 12, halt_status 1
[    2.495557] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.495560] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.495564] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.495567] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.495572] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.495577] dwc2 c90c0000.usb:   Control status transaction
[    2.495581] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.495584] dwc2 c90c0000.usb: DMA enabled
[    2.495587] dwc2 c90c0000.usb: desc DMA disabled
[    2.495591] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.495594] dwc2 c90c0000.usb: set HAINTMSK to 00002000
[    2.495598] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.495602] dwc2 c90c0000.usb: set HCCHAR(13) to 00800040
[    2.495606] dwc2 c90c0000.usb: dwc2_hc_init: Channel 13
[    2.495609] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.495613] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.495616] dwc2 c90c0000.usb: 	 Is In: 0
[    2.495619] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.495623] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.495626] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.495630] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.495634] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.495637] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.495642] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.495645] dwc2 c90c0000.usb: no split
[    2.495650] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(13)
[    2.495654] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 13
[    2.495657] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.495660] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.495664] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.495668] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(13)
[    2.495671] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.495675] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(13)
[    2.495679] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.495684] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf3000006
[    2.495698] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.495701] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.495705] dwc2 c90c0000.usb: HAINT=00002000
[    2.495709] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 13
[    2.495714] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.495718] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Channel Halted--
[    2.495722] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: DMA Channel Halted--
[    2.495726] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Transfer Complete--
[    2.495729] dwc2 c90c0000.usb:   Control transfer complete
[    2.495735] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 2
[    2.495740] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.495744] dwc2 c90c0000.usb:   dwc2_release_channel: channel 13, halt_status 2
[    2.495748] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.495752] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.495755] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.495760] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.495764] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.495839] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.495845] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.495849] dwc2 c90c0000.usb:   Device address: 2
[    2.495853] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.495857] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.495860] dwc2 c90c0000.usb:   Speed: HIGH
[    2.495869] dwc2 c90c0000.usb:   Max packet size: 64
[    2.495872] dwc2 c90c0000.usb:   Data buffer length: 4
[    2.495877] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa87400
[    2.495881] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1fa874c0
[    2.495884] dwc2 c90c0000.usb:   Interval: 0
[    2.495891] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.495896] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.495901] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.495905] dwc2 c90c0000.usb:   Control setup transaction
[    2.495908] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.495912] dwc2 c90c0000.usb: DMA enabled
[    2.495915] dwc2 c90c0000.usb: desc DMA disabled
[    2.495919] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.495923] dwc2 c90c0000.usb: set HAINTMSK to 00004000
[    2.495927] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.495931] dwc2 c90c0000.usb: set HCCHAR(14) to 00800040
[    2.495935] dwc2 c90c0000.usb: dwc2_hc_init: Channel 14
[    2.495939] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.495942] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.495946] dwc2 c90c0000.usb: 	 Is In: 0
[    2.495949] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.495952] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.495956] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.495960] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.495964] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.495968] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.495972] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.495975] dwc2 c90c0000.usb: no split
[    2.495980] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(14)
[    2.495984] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 14
[    2.495987] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.495991] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.495994] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.495999] dwc2 c90c0000.usb: Wrote 1fa874c0 to HCDMA(14)
[    2.496002] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.496006] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(14)
[    2.496031] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.496036] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.496039] dwc2 c90c0000.usb: HAINT=00004000
[    2.496044] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 14
[    2.496049] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.496054] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Channel Halted--
[    2.496057] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: DMA Channel Halted--
[    2.496062] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Transfer Complete--
[    2.496066] dwc2 c90c0000.usb:   Control setup transaction done
[    2.496069] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.496074] dwc2 c90c0000.usb:   dwc2_release_channel: channel 14, halt_status 1
[    2.496079] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.496083] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.496086] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.496090] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.496095] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.496099] dwc2 c90c0000.usb:   Control data transaction
[    2.496103] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.496106] dwc2 c90c0000.usb: DMA enabled
[    2.496110] dwc2 c90c0000.usb: desc DMA disabled
[    2.496114] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.496118] dwc2 c90c0000.usb: set HAINTMSK to 00008000
[    2.496121] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.496126] dwc2 c90c0000.usb: set HCCHAR(15) to 00808040
[    2.496129] dwc2 c90c0000.usb: dwc2_hc_init: Channel 15
[    2.496133] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.496136] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.496140] dwc2 c90c0000.usb: 	 Is In: 1
[    2.496143] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.496146] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.496150] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.496154] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.496157] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.496161] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.496165] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.496169] dwc2 c90c0000.usb: no split
[    2.496173] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(15)
[    2.496177] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 15
[    2.496181] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.496184] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.496187] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.496192] dwc2 c90c0000.usb: Wrote 1fa87400 to HCDMA(15)
[    2.496196] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.496200] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(15)
[    2.496205] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.496209] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.496437] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.496444] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.496448] dwc2 c90c0000.usb: HAINT=00008000
[    2.496453] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 15
[    2.496459] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.496464] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Channel Halted--
[    2.496468] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: DMA Channel Halted--
[    2.496474] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Transfer Complete--
[    2.496482] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4
[    2.496487] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 15
[    2.496491] dwc2 c90c0000.usb:   chan->xfer_len 64
[    2.496495] dwc2 c90c0000.usb:   hctsiz.xfersize 60
[    2.496498] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4
[    2.496502] dwc2 c90c0000.usb:   urb->actual_length 4
[    2.496506] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.496510] dwc2 c90c0000.usb:   Control data transfer done
[    2.496514] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.496518] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.496522] dwc2 c90c0000.usb: DMA enabled
[    2.496526] dwc2 c90c0000.usb:   dwc2_release_channel: channel 15, halt_status 1
[    2.496532] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.496536] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.496540] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.496543] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.496549] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.496554] dwc2 c90c0000.usb:   Control status transaction
[    2.496558] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.496561] dwc2 c90c0000.usb: DMA enabled
[    2.496565] dwc2 c90c0000.usb: desc DMA disabled
[    2.496568] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.496572] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[    2.496576] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.496580] dwc2 c90c0000.usb: set HCCHAR(0) to 00800040
[    2.496584] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[    2.496587] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.496591] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.496594] dwc2 c90c0000.usb: 	 Is In: 0
[    2.496598] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.496601] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.496605] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.496609] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.496612] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.496616] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.496620] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.496624] dwc2 c90c0000.usb: no split
[    2.496629] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(0)
[    2.496633] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[    2.496636] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.496639] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.496643] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.496647] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(0)
[    2.496651] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.496655] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(0)
[    2.496660] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.496664] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf3000006
[    2.496687] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.496691] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.496695] dwc2 c90c0000.usb: HAINT=00000001
[    2.496699] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[    2.496703] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.496708] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Channel Halted--
[    2.496711] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: DMA Channel Halted--
[    2.496715] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Transfer Complete--
[    2.496719] dwc2 c90c0000.usb:   Control transfer complete
[    2.496725] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 4
[    2.496731] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.496736] dwc2 c90c0000.usb:   dwc2_release_channel: channel 0, halt_status 2
[    2.496740] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.496744] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.496747] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.496751] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.496756] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.497261] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.497267] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.497272] dwc2 c90c0000.usb:   Device address: 2
[    2.497276] dwc2 c90c0000.usb:   Endpoint: 0, OUT
[    2.497280] dwc2 c90c0000.usb:   Endpoint type: CONTROL OUT (OUT)
[    2.497284] dwc2 c90c0000.usb:   Speed: HIGH
[    2.497288] dwc2 c90c0000.usb:   Max packet size: 64
[    2.497291] dwc2 c90c0000.usb:   Data buffer length: 0
[    2.497297] dwc2 c90c0000.usb:   Transfer buffer:   (null), Transfer DMA: 00000000
[    2.497301] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1fa874c0
[    2.497304] dwc2 c90c0000.usb:   Interval: 0
[    2.497310] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=0, ep_type=0, mps=64
[    2.497317] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.497323] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.497328] dwc2 c90c0000.usb:   Control setup transaction
[    2.497333] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.497337] dwc2 c90c0000.usb: DMA enabled
[    2.497340] dwc2 c90c0000.usb: desc DMA disabled
[    2.497344] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.497348] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[    2.497352] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.497356] dwc2 c90c0000.usb: set HCCHAR(1) to 00800040
[    2.497360] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[    2.497363] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.497367] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.497370] dwc2 c90c0000.usb: 	 Is In: 0
[    2.497373] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.497377] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.497380] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.497385] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.497389] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.497393] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.497398] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.497401] dwc2 c90c0000.usb: no split
[    2.497406] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(1)
[    2.497410] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[    2.497414] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.497417] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.497421] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.497425] dwc2 c90c0000.usb: Wrote 1fa874c0 to HCDMA(1)
[    2.497429] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.497433] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(1)
[    2.497443] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.497447] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.497451] dwc2 c90c0000.usb: HAINT=00000002
[    2.497456] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[    2.497460] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.497464] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[    2.497468] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[    2.497473] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[    2.497477] dwc2 c90c0000.usb:   Control setup transaction done
[    2.497481] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.497485] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 1
[    2.497490] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.497493] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.497497] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.497500] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.497506] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.497510] dwc2 c90c0000.usb:   Control status transaction
[    2.497514] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.497517] dwc2 c90c0000.usb: DMA enabled
[    2.497520] dwc2 c90c0000.usb: desc DMA disabled
[    2.497524] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.497528] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[    2.497532] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.497536] dwc2 c90c0000.usb: set HCCHAR(2) to 00808040
[    2.497539] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[    2.497543] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.497546] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.497550] dwc2 c90c0000.usb: 	 Is In: 1
[    2.497553] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.497557] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.497560] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.497563] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.497567] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.497571] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.497575] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.497578] dwc2 c90c0000.usb: no split
[    2.497583] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(2)
[    2.497586] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[    2.497590] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.497593] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.497597] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.497601] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(2)
[    2.497605] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.497609] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(2)
[    2.497613] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.497617] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.497866] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.497873] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.497877] dwc2 c90c0000.usb: HAINT=00000004
[    2.497882] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[    2.497886] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.497891] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[    2.497894] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[    2.497899] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[    2.497903] dwc2 c90c0000.usb:   Control transfer complete
[    2.497909] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-OUT status 0 actual 0
[    2.497915] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.497919] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.497922] dwc2 c90c0000.usb: DMA enabled
[    2.497926] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 2
[    2.497931] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.497935] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.497938] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.497944] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.497949] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.497986] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.497992] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.497995] dwc2 c90c0000.usb:   Device address: 2
[    2.498000] dwc2 c90c0000.usb:   Endpoint: 0, OUT
[    2.498003] dwc2 c90c0000.usb:   Endpoint type: CONTROL OUT (OUT)
[    2.498007] dwc2 c90c0000.usb:   Speed: HIGH
[    2.498011] dwc2 c90c0000.usb:   Max packet size: 64
[    2.498015] dwc2 c90c0000.usb:   Data buffer length: 0
[    2.498019] dwc2 c90c0000.usb:   Transfer buffer:   (null), Transfer DMA: 00000000
[    2.498024] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1fa874c0
[    2.498027] dwc2 c90c0000.usb:   Interval: 0
[    2.498033] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=0, ep_type=0, mps=64
[    2.498038] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.498044] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.498048] dwc2 c90c0000.usb:   Control setup transaction
[    2.498052] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.498055] dwc2 c90c0000.usb: DMA enabled
[    2.498058] dwc2 c90c0000.usb: desc DMA disabled
[    2.498062] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.498066] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[    2.498070] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.498074] dwc2 c90c0000.usb: set HCCHAR(3) to 00800040
[    2.498078] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[    2.498081] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.498084] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.498088] dwc2 c90c0000.usb: 	 Is In: 0
[    2.498091] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.498095] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.498098] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.498102] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.498106] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.498110] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.498114] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.498117] dwc2 c90c0000.usb: no split
[    2.498122] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(3)
[    2.498126] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[    2.498129] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.498132] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.498136] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.498140] dwc2 c90c0000.usb: Wrote 1fa874c0 to HCDMA(3)
[    2.498144] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.498148] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(3)
[    2.498165] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.498169] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.498173] dwc2 c90c0000.usb: HAINT=00000008
[    2.498177] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[    2.498182] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.498186] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[    2.498189] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[    2.498193] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[    2.498197] dwc2 c90c0000.usb:   Control setup transaction done
[    2.498201] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.498205] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 1
[    2.498209] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.498213] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.498216] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.498219] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.498224] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.498228] dwc2 c90c0000.usb:   Control status transaction
[    2.498231] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.498235] dwc2 c90c0000.usb: DMA enabled
[    2.498238] dwc2 c90c0000.usb: desc DMA disabled
[    2.498242] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.498246] dwc2 c90c0000.usb: set HAINTMSK to 00000010
[    2.498250] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.498254] dwc2 c90c0000.usb: set HCCHAR(4) to 00808040
[    2.498258] dwc2 c90c0000.usb: dwc2_hc_init: Channel 4
[    2.498261] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.498265] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.498268] dwc2 c90c0000.usb: 	 Is In: 1
[    2.498271] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.498275] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.498278] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.498282] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.498286] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.498289] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.498293] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.498296] dwc2 c90c0000.usb: no split
[    2.498301] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(4)
[    2.498305] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 4
[    2.498308] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.498311] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.498315] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.498319] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(4)
[    2.498323] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.498326] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(4)
[    2.498331] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.498335] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.498587] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.498592] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.498596] dwc2 c90c0000.usb: HAINT=00000010
[    2.498601] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 4
[    2.498605] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.498610] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Channel Halted--
[    2.498614] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: DMA Channel Halted--
[    2.498618] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Transfer Complete--
[    2.498622] dwc2 c90c0000.usb:   Control transfer complete
[    2.498628] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-OUT status 0 actual 0
[    2.498634] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.498638] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.498641] dwc2 c90c0000.usb: DMA enabled
[    2.498646] dwc2 c90c0000.usb:   dwc2_release_channel: channel 4, halt_status 2
[    2.498650] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.498654] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.498657] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.498662] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.498667] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.498708] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.498713] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.498717] dwc2 c90c0000.usb:   Device address: 2
[    2.498721] dwc2 c90c0000.usb:   Endpoint: 0, OUT
[    2.498725] dwc2 c90c0000.usb:   Endpoint type: CONTROL OUT (OUT)
[    2.498729] dwc2 c90c0000.usb:   Speed: HIGH
[    2.498733] dwc2 c90c0000.usb:   Max packet size: 64
[    2.498736] dwc2 c90c0000.usb:   Data buffer length: 0
[    2.498741] dwc2 c90c0000.usb:   Transfer buffer:   (null), Transfer DMA: 00000000
[    2.498745] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1fa874c0
[    2.498749] dwc2 c90c0000.usb:   Interval: 0
[    2.498755] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=0, ep_type=0, mps=64
[    2.498761] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.498766] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.498771] dwc2 c90c0000.usb:   Control setup transaction
[    2.498774] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.498778] dwc2 c90c0000.usb: DMA enabled
[    2.498781] dwc2 c90c0000.usb: desc DMA disabled
[    2.498785] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.498789] dwc2 c90c0000.usb: set HAINTMSK to 00000020
[    2.498793] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.498798] dwc2 c90c0000.usb: set HCCHAR(5) to 00800040
[    2.498801] dwc2 c90c0000.usb: dwc2_hc_init: Channel 5
[    2.498805] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.498808] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.498811] dwc2 c90c0000.usb: 	 Is In: 0
[    2.498815] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.498818] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.498822] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.498826] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.498829] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.498833] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.498838] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.498841] dwc2 c90c0000.usb: no split
[    2.498846] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(5)
[    2.498850] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 5
[    2.498853] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.498857] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.498860] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.498864] dwc2 c90c0000.usb: Wrote 1fa874c0 to HCDMA(5)
[    2.498868] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.498872] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(5)
[    2.498884] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.498887] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.498891] dwc2 c90c0000.usb: HAINT=00000020
[    2.498895] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 5
[    2.498900] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.498904] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Channel Halted--
[    2.498908] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: DMA Channel Halted--
[    2.498913] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Transfer Complete--
[    2.498916] dwc2 c90c0000.usb:   Control setup transaction done
[    2.498920] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.498924] dwc2 c90c0000.usb:   dwc2_release_channel: channel 5, halt_status 1
[    2.498928] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.498932] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.498936] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.498939] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.498944] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.498947] dwc2 c90c0000.usb:   Control status transaction
[    2.498951] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.498954] dwc2 c90c0000.usb: DMA enabled
[    2.498957] dwc2 c90c0000.usb: desc DMA disabled
[    2.498961] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.498965] dwc2 c90c0000.usb: set HAINTMSK to 00000040
[    2.498969] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.498973] dwc2 c90c0000.usb: set HCCHAR(6) to 00808040
[    2.498977] dwc2 c90c0000.usb: dwc2_hc_init: Channel 6
[    2.498980] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.498984] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.498987] dwc2 c90c0000.usb: 	 Is In: 1
[    2.498990] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.498994] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.498997] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.499001] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.499004] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.499008] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.499012] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.499015] dwc2 c90c0000.usb: no split
[    2.499020] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(6)
[    2.499023] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 6
[    2.499027] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.499030] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.499033] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.499038] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(6)
[    2.499041] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.499045] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(6)
[    2.499049] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.499053] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.499308] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.499314] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.499318] dwc2 c90c0000.usb: HAINT=00000040
[    2.499323] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 6
[    2.499328] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.499332] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Channel Halted--
[    2.499336] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: DMA Channel Halted--
[    2.499340] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Transfer Complete--
[    2.499344] dwc2 c90c0000.usb:   Control transfer complete
[    2.499350] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-OUT status 0 actual 0
[    2.499356] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.499359] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.499363] dwc2 c90c0000.usb: DMA enabled
[    2.499367] dwc2 c90c0000.usb:   dwc2_release_channel: channel 6, halt_status 2
[    2.499372] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.499376] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.499380] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.499385] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.499390] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.499421] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.499425] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.499429] dwc2 c90c0000.usb:   Device address: 2
[    2.499433] dwc2 c90c0000.usb:   Endpoint: 0, OUT
[    2.499437] dwc2 c90c0000.usb:   Endpoint type: CONTROL OUT (OUT)
[    2.499441] dwc2 c90c0000.usb:   Speed: HIGH
[    2.499445] dwc2 c90c0000.usb:   Max packet size: 64
[    2.499448] dwc2 c90c0000.usb:   Data buffer length: 0
[    2.499453] dwc2 c90c0000.usb:   Transfer buffer:   (null), Transfer DMA: 00000000
[    2.499457] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1fa874c0
[    2.499461] dwc2 c90c0000.usb:   Interval: 0
[    2.499466] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=0, ep_type=0, mps=64
[    2.499471] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.499476] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.499481] dwc2 c90c0000.usb:   Control setup transaction
[    2.499484] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.499487] dwc2 c90c0000.usb: DMA enabled
[    2.499491] dwc2 c90c0000.usb: desc DMA disabled
[    2.499494] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.499498] dwc2 c90c0000.usb: set HAINTMSK to 00000080
[    2.499502] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.499507] dwc2 c90c0000.usb: set HCCHAR(7) to 00800040
[    2.499510] dwc2 c90c0000.usb: dwc2_hc_init: Channel 7
[    2.499514] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.499517] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.499520] dwc2 c90c0000.usb: 	 Is In: 0
[    2.499524] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.499527] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.499530] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.499534] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.499538] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.499542] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.499546] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.499549] dwc2 c90c0000.usb: no split
[    2.499554] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(7)
[    2.499558] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 7
[    2.499561] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.499565] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.499568] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.499573] dwc2 c90c0000.usb: Wrote 1fa874c0 to HCDMA(7)
[    2.499576] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.499581] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(7)
[    2.499589] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.499593] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.499597] dwc2 c90c0000.usb: HAINT=00000080
[    2.499601] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 7
[    2.499605] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.499610] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Channel Halted--
[    2.499614] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: DMA Channel Halted--
[    2.499618] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Transfer Complete--
[    2.499621] dwc2 c90c0000.usb:   Control setup transaction done
[    2.499625] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.499629] dwc2 c90c0000.usb:   dwc2_release_channel: channel 7, halt_status 1
[    2.499634] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.499637] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.499641] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.499644] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.499649] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.499653] dwc2 c90c0000.usb:   Control status transaction
[    2.499657] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.499660] dwc2 c90c0000.usb: DMA enabled
[    2.499663] dwc2 c90c0000.usb: desc DMA disabled
[    2.499667] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.499671] dwc2 c90c0000.usb: set HAINTMSK to 00000100
[    2.499674] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.499678] dwc2 c90c0000.usb: set HCCHAR(8) to 00808040
[    2.499682] dwc2 c90c0000.usb: dwc2_hc_init: Channel 8
[    2.499686] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.499689] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.499692] dwc2 c90c0000.usb: 	 Is In: 1
[    2.499696] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.499699] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.499703] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.499706] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.499710] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.499714] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.499718] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.499721] dwc2 c90c0000.usb: no split
[    2.499726] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(8)
[    2.499730] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 8
[    2.499733] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.499736] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.499740] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.499744] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(8)
[    2.499747] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.499751] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(8)
[    2.499756] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.499760] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.500017] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.500024] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.500027] dwc2 c90c0000.usb: HAINT=00000100
[    2.500032] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 8
[    2.500037] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.500042] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Channel Halted--
[    2.500046] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: DMA Channel Halted--
[    2.500050] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Transfer Complete--
[    2.500054] dwc2 c90c0000.usb:   Control transfer complete
[    2.500060] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-OUT status 0 actual 0
[    2.500066] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.500069] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.500073] dwc2 c90c0000.usb: DMA enabled
[    2.500077] dwc2 c90c0000.usb:   dwc2_release_channel: channel 8, halt_status 2
[    2.500082] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.500086] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.500090] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.500095] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.500100] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.500398] dwc2 c90c0000.usb: GetPortStatus wIndex=0x0001 flags=0x0000000a
[    2.500405] dwc2 c90c0000.usb:   HPRT0: 0x00001005
[    2.500409] dwc2 c90c0000.usb: port_status=00020503
[    2.500457] dwc2 c90c0000.usb: ClearPortFeature USB_PORT_FEAT_C_ENABLE
[    2.605995] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.606004] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.606009] dwc2 c90c0000.usb:   Device address: 2
[    2.606013] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.606017] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.606021] dwc2 c90c0000.usb:   Speed: HIGH
[    2.606025] dwc2 c90c0000.usb:   Max packet size: 64
[    2.606029] dwc2 c90c0000.usb:   Data buffer length: 4
[    2.606034] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa87400
[    2.606038] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1f8efe00
[    2.606041] dwc2 c90c0000.usb:   Interval: 0
[    2.606047] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.606054] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.606060] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.606065] dwc2 c90c0000.usb:   Control setup transaction
[    2.606069] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.606072] dwc2 c90c0000.usb: DMA enabled
[    2.606076] dwc2 c90c0000.usb: desc DMA disabled
[    2.606080] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.606084] dwc2 c90c0000.usb: set HAINTMSK to 00000200
[    2.606088] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.606092] dwc2 c90c0000.usb: set HCCHAR(9) to 00800040
[    2.606096] dwc2 c90c0000.usb: dwc2_hc_init: Channel 9
[    2.606099] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.606102] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.606106] dwc2 c90c0000.usb: 	 Is In: 0
[    2.606109] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.606113] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.606116] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.606120] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.606124] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.606128] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.606133] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.606136] dwc2 c90c0000.usb: no split
[    2.606141] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(9)
[    2.606145] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 9
[    2.606149] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.606152] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.606155] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.606160] dwc2 c90c0000.usb: Wrote 1f8efe00 to HCDMA(9)
[    2.606164] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.606168] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(9)
[    2.606180] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.606184] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.606188] dwc2 c90c0000.usb: HAINT=00000200
[    2.606192] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 9
[    2.606197] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.606201] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Channel Halted--
[    2.606205] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: DMA Channel Halted--
[    2.606210] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Transfer Complete--
[    2.606214] dwc2 c90c0000.usb:   Control setup transaction done
[    2.606218] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.606223] dwc2 c90c0000.usb:   dwc2_release_channel: channel 9, halt_status 1
[    2.606228] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.606231] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.606235] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.606238] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.606244] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.606247] dwc2 c90c0000.usb:   Control data transaction
[    2.606251] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.606254] dwc2 c90c0000.usb: DMA enabled
[    2.606257] dwc2 c90c0000.usb: desc DMA disabled
[    2.606261] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.606265] dwc2 c90c0000.usb: set HAINTMSK to 00000400
[    2.606269] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.606273] dwc2 c90c0000.usb: set HCCHAR(10) to 00808040
[    2.606277] dwc2 c90c0000.usb: dwc2_hc_init: Channel 10
[    2.606280] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.606284] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.606288] dwc2 c90c0000.usb: 	 Is In: 1
[    2.606291] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.606294] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.606298] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.606301] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.606305] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.606309] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.606312] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.606315] dwc2 c90c0000.usb: no split
[    2.606320] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(10)
[    2.606324] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 10
[    2.606327] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.606330] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.606334] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.606338] dwc2 c90c0000.usb: Wrote 1fa87400 to HCDMA(10)
[    2.606342] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.606346] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(10)
[    2.606351] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.606355] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.606584] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.606590] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.606594] dwc2 c90c0000.usb: HAINT=00000400
[    2.606599] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 10
[    2.606603] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.606608] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Channel Halted--
[    2.606612] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: DMA Channel Halted--
[    2.606616] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Transfer Complete--
[    2.606622] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4
[    2.606626] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 10
[    2.606630] dwc2 c90c0000.usb:   chan->xfer_len 64
[    2.606633] dwc2 c90c0000.usb:   hctsiz.xfersize 60
[    2.606637] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4
[    2.606640] dwc2 c90c0000.usb:   urb->actual_length 4
[    2.606644] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.606648] dwc2 c90c0000.usb:   Control data transfer done
[    2.606651] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.606655] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.606658] dwc2 c90c0000.usb: DMA enabled
[    2.606663] dwc2 c90c0000.usb:   dwc2_release_channel: channel 10, halt_status 1
[    2.606667] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.606671] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.606675] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.606679] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.606684] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.606689] dwc2 c90c0000.usb:   Control status transaction
[    2.606693] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.606696] dwc2 c90c0000.usb: DMA enabled
[    2.606699] dwc2 c90c0000.usb: desc DMA disabled
[    2.606703] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.606707] dwc2 c90c0000.usb: set HAINTMSK to 00000800
[    2.606711] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.606715] dwc2 c90c0000.usb: set HCCHAR(11) to 00800040
[    2.606719] dwc2 c90c0000.usb: dwc2_hc_init: Channel 11
[    2.606722] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.606726] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.606730] dwc2 c90c0000.usb: 	 Is In: 0
[    2.606733] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.606736] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.606740] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.606743] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.606747] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.606751] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.606755] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.606758] dwc2 c90c0000.usb: no split
[    2.606763] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(11)
[    2.606767] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 11
[    2.606770] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.606774] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.606777] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.606781] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(11)
[    2.606785] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.606789] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(11)
[    2.606794] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.606798] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf3000006
[    2.606812] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.606815] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.606819] dwc2 c90c0000.usb: HAINT=00000800
[    2.606823] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 11
[    2.606828] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.606832] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Channel Halted--
[    2.606836] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: DMA Channel Halted--
[    2.606840] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Transfer Complete--
[    2.606844] dwc2 c90c0000.usb:   Control transfer complete
[    2.606851] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 4
[    2.606856] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.606861] dwc2 c90c0000.usb:   dwc2_release_channel: channel 11, halt_status 2
[    2.606866] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.606869] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.606873] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.606877] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.606882] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.606921] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.606927] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.606931] dwc2 c90c0000.usb:   Device address: 2
[    2.606934] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.606939] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.606942] dwc2 c90c0000.usb:   Speed: HIGH
[    2.606946] dwc2 c90c0000.usb:   Max packet size: 64
[    2.606950] dwc2 c90c0000.usb:   Data buffer length: 4
[    2.606954] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa87400
[    2.606958] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1f8efe00
[    2.606961] dwc2 c90c0000.usb:   Interval: 0
[    2.606967] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.606973] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.606978] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.606983] dwc2 c90c0000.usb:   Control setup transaction
[    2.606986] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.606990] dwc2 c90c0000.usb: DMA enabled
[    2.606993] dwc2 c90c0000.usb: desc DMA disabled
[    2.606997] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.607001] dwc2 c90c0000.usb: set HAINTMSK to 00001000
[    2.607005] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.607009] dwc2 c90c0000.usb: set HCCHAR(12) to 00800040
[    2.607013] dwc2 c90c0000.usb: dwc2_hc_init: Channel 12
[    2.607016] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.607020] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.607023] dwc2 c90c0000.usb: 	 Is In: 0
[    2.607027] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.607030] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.607033] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.607037] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.607041] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.607045] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.607049] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.607052] dwc2 c90c0000.usb: no split
[    2.607056] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(12)
[    2.607060] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 12
[    2.607064] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.607067] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.607071] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.607075] dwc2 c90c0000.usb: Wrote 1f8efe00 to HCDMA(12)
[    2.607078] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.607082] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(12)
[    2.607091] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.607095] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.607098] dwc2 c90c0000.usb: HAINT=00001000
[    2.607103] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 12
[    2.607107] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.607111] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Channel Halted--
[    2.607115] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: DMA Channel Halted--
[    2.607119] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Transfer Complete--
[    2.607123] dwc2 c90c0000.usb:   Control setup transaction done
[    2.607126] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.607131] dwc2 c90c0000.usb:   dwc2_release_channel: channel 12, halt_status 1
[    2.607136] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.607140] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.607143] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.607146] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.607151] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.607155] dwc2 c90c0000.usb:   Control data transaction
[    2.607158] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.607161] dwc2 c90c0000.usb: DMA enabled
[    2.607165] dwc2 c90c0000.usb: desc DMA disabled
[    2.607168] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.607172] dwc2 c90c0000.usb: set HAINTMSK to 00002000
[    2.607176] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.607181] dwc2 c90c0000.usb: set HCCHAR(13) to 00808040
[    2.607185] dwc2 c90c0000.usb: dwc2_hc_init: Channel 13
[    2.607188] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.607192] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.607196] dwc2 c90c0000.usb: 	 Is In: 1
[    2.607199] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.607202] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.607206] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.607209] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.607213] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.607216] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.607220] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.607224] dwc2 c90c0000.usb: no split
[    2.607228] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(13)
[    2.607232] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 13
[    2.607235] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.607239] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.607242] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.607246] dwc2 c90c0000.usb: Wrote 1fa87400 to HCDMA(13)
[    2.607250] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.607254] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(13)
[    2.607258] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.607263] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.607496] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.607501] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.607505] dwc2 c90c0000.usb: HAINT=00002000
[    2.607510] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 13
[    2.607515] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.607519] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Channel Halted--
[    2.607523] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: DMA Channel Halted--
[    2.607528] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Transfer Complete--
[    2.607533] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4
[    2.607537] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 13
[    2.607541] dwc2 c90c0000.usb:   chan->xfer_len 64
[    2.607544] dwc2 c90c0000.usb:   hctsiz.xfersize 60
[    2.607548] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4
[    2.607551] dwc2 c90c0000.usb:   urb->actual_length 4
[    2.607555] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.607558] dwc2 c90c0000.usb:   Control data transfer done
[    2.607562] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.607565] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.607569] dwc2 c90c0000.usb: DMA enabled
[    2.607573] dwc2 c90c0000.usb:   dwc2_release_channel: channel 13, halt_status 1
[    2.607578] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.607581] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.607585] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.607589] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.607594] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.607598] dwc2 c90c0000.usb:   Control status transaction
[    2.607602] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.607606] dwc2 c90c0000.usb: DMA enabled
[    2.607609] dwc2 c90c0000.usb: desc DMA disabled
[    2.607613] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.607617] dwc2 c90c0000.usb: set HAINTMSK to 00004000
[    2.607621] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.607625] dwc2 c90c0000.usb: set HCCHAR(14) to 00800040
[    2.607629] dwc2 c90c0000.usb: dwc2_hc_init: Channel 14
[    2.607632] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.607636] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.607639] dwc2 c90c0000.usb: 	 Is In: 0
[    2.607642] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.607646] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.607649] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.607653] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.607657] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.607660] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.607665] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.607668] dwc2 c90c0000.usb: no split
[    2.607673] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(14)
[    2.607676] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 14
[    2.607680] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.607683] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.607687] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.607691] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(14)
[    2.607694] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.607699] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(14)
[    2.607703] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.607708] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf3000006
[    2.607719] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.607722] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.607726] dwc2 c90c0000.usb: HAINT=00004000
[    2.607730] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 14
[    2.607735] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.607739] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Channel Halted--
[    2.607742] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: DMA Channel Halted--
[    2.607747] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Transfer Complete--
[    2.607750] dwc2 c90c0000.usb:   Control transfer complete
[    2.607757] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 4
[    2.607763] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.607767] dwc2 c90c0000.usb:   dwc2_release_channel: channel 14, halt_status 2
[    2.607772] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.607775] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.607779] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.607783] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.607787] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.607844] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.607849] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.607853] dwc2 c90c0000.usb:   Device address: 2
[    2.607857] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.607861] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.607865] dwc2 c90c0000.usb:   Speed: HIGH
[    2.607869] dwc2 c90c0000.usb:   Max packet size: 64
[    2.607872] dwc2 c90c0000.usb:   Data buffer length: 4
[    2.607877] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa87400
[    2.607881] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1f8efe00
[    2.607884] dwc2 c90c0000.usb:   Interval: 0
[    2.607890] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.607896] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.607901] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.607906] dwc2 c90c0000.usb:   Control setup transaction
[    2.607910] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.607914] dwc2 c90c0000.usb: DMA enabled
[    2.607917] dwc2 c90c0000.usb: desc DMA disabled
[    2.607921] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.607925] dwc2 c90c0000.usb: set HAINTMSK to 00008000
[    2.607929] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.607933] dwc2 c90c0000.usb: set HCCHAR(15) to 00800040
[    2.607937] dwc2 c90c0000.usb: dwc2_hc_init: Channel 15
[    2.607940] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.607944] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.607947] dwc2 c90c0000.usb: 	 Is In: 0
[    2.607951] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.607954] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.607958] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.607961] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.607965] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.607969] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.607973] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.607976] dwc2 c90c0000.usb: no split
[    2.607981] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(15)
[    2.607985] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 15
[    2.607989] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.607992] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.607995] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.608000] dwc2 c90c0000.usb: Wrote 1f8efe00 to HCDMA(15)
[    2.608003] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.608008] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(15)
[    2.608017] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.608021] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.608024] dwc2 c90c0000.usb: HAINT=00008000
[    2.608028] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 15
[    2.608033] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.608037] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Channel Halted--
[    2.608041] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: DMA Channel Halted--
[    2.608046] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Transfer Complete--
[    2.608050] dwc2 c90c0000.usb:   Control setup transaction done
[    2.608053] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.608058] dwc2 c90c0000.usb:   dwc2_release_channel: channel 15, halt_status 1
[    2.608063] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.608066] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.608069] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.608072] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.608077] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.608081] dwc2 c90c0000.usb:   Control data transaction
[    2.608084] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.608088] dwc2 c90c0000.usb: DMA enabled
[    2.608091] dwc2 c90c0000.usb: desc DMA disabled
[    2.608095] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.608099] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[    2.608103] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.608107] dwc2 c90c0000.usb: set HCCHAR(0) to 00808040
[    2.608110] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[    2.608114] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.608117] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.608120] dwc2 c90c0000.usb: 	 Is In: 1
[    2.608124] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.608127] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.608131] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.608135] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.608138] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.608142] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.608146] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.608149] dwc2 c90c0000.usb: no split
[    2.608154] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(0)
[    2.608157] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[    2.608161] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.608164] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.608168] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.608172] dwc2 c90c0000.usb: Wrote 1fa87400 to HCDMA(0)
[    2.608175] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.608179] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(0)
[    2.608184] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.608188] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.608419] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.608425] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.608428] dwc2 c90c0000.usb: HAINT=00000001
[    2.608433] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[    2.608437] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.608442] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Channel Halted--
[    2.608446] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: DMA Channel Halted--
[    2.608450] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Transfer Complete--
[    2.608455] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4
[    2.608460] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 0
[    2.608464] dwc2 c90c0000.usb:   chan->xfer_len 64
[    2.608467] dwc2 c90c0000.usb:   hctsiz.xfersize 60
[    2.608471] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4
[    2.608474] dwc2 c90c0000.usb:   urb->actual_length 4
[    2.608478] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.608481] dwc2 c90c0000.usb:   Control data transfer done
[    2.608485] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.608488] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.608492] dwc2 c90c0000.usb: DMA enabled
[    2.608497] dwc2 c90c0000.usb:   dwc2_release_channel: channel 0, halt_status 1
[    2.608502] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.608505] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.608509] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.608513] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.608518] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.608523] dwc2 c90c0000.usb:   Control status transaction
[    2.608527] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.608530] dwc2 c90c0000.usb: DMA enabled
[    2.608533] dwc2 c90c0000.usb: desc DMA disabled
[    2.608537] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.608542] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[    2.608546] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.608550] dwc2 c90c0000.usb: set HCCHAR(1) to 00800040
[    2.608553] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[    2.608557] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.608560] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.608563] dwc2 c90c0000.usb: 	 Is In: 0
[    2.608567] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.608570] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.608574] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.608578] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.608581] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.608585] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.608589] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.608592] dwc2 c90c0000.usb: no split
[    2.608597] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(1)
[    2.608601] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[    2.608605] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.608608] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.608612] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.608616] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(1)
[    2.608620] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.608624] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(1)
[    2.608629] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.608633] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf3000006
[    2.608643] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.608647] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.608651] dwc2 c90c0000.usb: HAINT=00000002
[    2.608655] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[    2.608659] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.608663] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[    2.608667] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[    2.608671] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[    2.608675] dwc2 c90c0000.usb:   Control transfer complete
[    2.608682] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 4
[    2.608687] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.608692] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 2
[    2.608696] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.608700] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.608703] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.608708] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.608712] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.608747] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.608752] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.608756] dwc2 c90c0000.usb:   Device address: 2
[    2.608760] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.608764] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.608767] dwc2 c90c0000.usb:   Speed: HIGH
[    2.608771] dwc2 c90c0000.usb:   Max packet size: 64
[    2.608775] dwc2 c90c0000.usb:   Data buffer length: 4
[    2.608779] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa87400
[    2.608783] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1f8efe00
[    2.608786] dwc2 c90c0000.usb:   Interval: 0
[    2.608792] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.608798] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.608803] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.608808] dwc2 c90c0000.usb:   Control setup transaction
[    2.608812] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.608815] dwc2 c90c0000.usb: DMA enabled
[    2.608818] dwc2 c90c0000.usb: desc DMA disabled
[    2.608822] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.608826] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[    2.608829] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.608834] dwc2 c90c0000.usb: set HCCHAR(2) to 00800040
[    2.608838] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[    2.608841] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.608845] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.608848] dwc2 c90c0000.usb: 	 Is In: 0
[    2.608851] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.608855] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.608859] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.608863] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.608868] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.608871] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.608876] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.608879] dwc2 c90c0000.usb: no split
[    2.608884] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(2)
[    2.608888] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[    2.608891] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.608895] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.608898] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.608903] dwc2 c90c0000.usb: Wrote 1f8efe00 to HCDMA(2)
[    2.608906] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.608910] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(2)
[    2.608919] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.608923] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.608926] dwc2 c90c0000.usb: HAINT=00000004
[    2.608930] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[    2.608935] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.608939] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[    2.608942] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[    2.608947] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[    2.608951] dwc2 c90c0000.usb:   Control setup transaction done
[    2.608954] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.608959] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 1
[    2.608963] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.608966] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.608970] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.608973] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.608978] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.608981] dwc2 c90c0000.usb:   Control data transaction
[    2.608985] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.608988] dwc2 c90c0000.usb: DMA enabled
[    2.608991] dwc2 c90c0000.usb: desc DMA disabled
[    2.608995] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.608999] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[    2.609002] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.609007] dwc2 c90c0000.usb: set HCCHAR(3) to 00808040
[    2.609010] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[    2.609014] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.609017] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.609020] dwc2 c90c0000.usb: 	 Is In: 1
[    2.609024] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.609027] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.609031] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.609034] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.609038] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.609042] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.609045] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.609048] dwc2 c90c0000.usb: no split
[    2.609053] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(3)
[    2.609057] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[    2.609060] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.609064] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.609067] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.609071] dwc2 c90c0000.usb: Wrote 1fa87400 to HCDMA(3)
[    2.609075] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.609079] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(3)
[    2.609083] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.609087] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.609320] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.609326] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.609330] dwc2 c90c0000.usb: HAINT=00000008
[    2.609334] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[    2.609339] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.609344] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[    2.609347] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[    2.609352] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[    2.609357] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4
[    2.609362] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 3
[    2.609365] dwc2 c90c0000.usb:   chan->xfer_len 64
[    2.609369] dwc2 c90c0000.usb:   hctsiz.xfersize 60
[    2.609373] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4
[    2.609376] dwc2 c90c0000.usb:   urb->actual_length 4
[    2.609380] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.609383] dwc2 c90c0000.usb:   Control data transfer done
[    2.609387] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.609391] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.609394] dwc2 c90c0000.usb: DMA enabled
[    2.609399] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 1
[    2.609404] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.609408] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.609411] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.609415] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.609420] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.609425] dwc2 c90c0000.usb:   Control status transaction
[    2.609428] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.609432] dwc2 c90c0000.usb: DMA enabled
[    2.609435] dwc2 c90c0000.usb: desc DMA disabled
[    2.609439] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.609442] dwc2 c90c0000.usb: set HAINTMSK to 00000010
[    2.609446] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.609451] dwc2 c90c0000.usb: set HCCHAR(4) to 00800040
[    2.609454] dwc2 c90c0000.usb: dwc2_hc_init: Channel 4
[    2.609458] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.609461] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.609465] dwc2 c90c0000.usb: 	 Is In: 0
[    2.609468] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.609471] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.609475] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.609479] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.609483] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.609487] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.609491] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.609494] dwc2 c90c0000.usb: no split
[    2.609499] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(4)
[    2.609503] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 4
[    2.609506] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.609510] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.609514] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.609518] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(4)
[    2.609521] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.609525] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(4)
[    2.609530] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.609534] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf3000006
[    2.609545] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.609549] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.609552] dwc2 c90c0000.usb: HAINT=00000010
[    2.609556] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 4
[    2.609561] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.609565] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Channel Halted--
[    2.609568] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: DMA Channel Halted--
[    2.609572] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Transfer Complete--
[    2.609576] dwc2 c90c0000.usb:   Control transfer complete
[    2.609582] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 4
[    2.609587] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.609592] dwc2 c90c0000.usb:   dwc2_release_channel: channel 4, halt_status 2
[    2.609597] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.609600] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.609603] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.609608] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.609612] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.609647] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.609652] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.609656] dwc2 c90c0000.usb:   Device address: 2
[    2.609660] dwc2 c90c0000.usb:   Endpoint: 1, IN
[    2.609664] dwc2 c90c0000.usb:   Endpoint type: INTERRUPT IN (IN)
[    2.609667] dwc2 c90c0000.usb:   Speed: HIGH
[    2.609671] dwc2 c90c0000.usb:   Max packet size: 1
[    2.609674] dwc2 c90c0000.usb:   Data buffer length: 1
[    2.609679] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa873c0
[    2.609684] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[    2.609688] dwc2 c90c0000.usb:   Interval: 2048
[    2.609694] dwc2 c90c0000.usb: addr=2, ep_num=1, ep_dir=80, ep_type=3, mps=1
[    2.609704] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.609747] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.609751] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.609755] dwc2 c90c0000.usb:   Device address: 2
[    2.609763] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.609767] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.609771] dwc2 c90c0000.usb: DMA enabled
[    2.609774] dwc2 c90c0000.usb: desc DMA disabled
[    2.609778] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.609782] dwc2 c90c0000.usb: set HAINTMSK to 00000020
[    2.609786] dwc2 c90c0000.usb: set GINTMSK to f300000e
[    2.609790] dwc2 c90c0000.usb: set HCCHAR(5) to 008c8801
[    2.609793] dwc2 c90c0000.usb: dwc2_hc_init: Channel 5
[    2.609797] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.609800] dwc2 c90c0000.usb: 	 Ep Num: 1
[    2.609804] dwc2 c90c0000.usb: 	 Is In: 1
[    2.609807] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.609810] dwc2 c90c0000.usb: 	 Ep Type: 3
[    2.609814] dwc2 c90c0000.usb: 	 Max Pkt: 1
[    2.609818] dwc2 c90c0000.usb: Queue periodic transactions
[    2.609822] dwc2 c90c0000.usb:   P Tx Req Queue Space Avail (before queue): 8
[    2.609825] dwc2 c90c0000.usb:   P Tx FIFO Space Avail (before queue): 500
[    2.609830] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.609833] dwc2 c90c0000.usb: no split
[    2.609838] dwc2 c90c0000.usb: Wrote 00080001 to HCTSIZ(5)
[    2.609842] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 5
[    2.609846] dwc2 c90c0000.usb: 	 Xfer Size: 1
[    2.609849] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.609853] dwc2 c90c0000.usb: 	 Start PID: 0
[    2.609857] dwc2 c90c0000.usb: Wrote 1fa873c0 to HCDMA(5)
[    2.609862] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.609866] dwc2 c90c0000.usb: Wrote 809c8801 to HCCHAR(5)
[    2.609873] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.609877] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.609885] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000008
[    2.609889] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.609893] dwc2 c90c0000.usb: HAINT=00000020
[    2.609897] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 5
[    2.609902] dwc2 c90c0000.usb:   hcint 0x00000012, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.609906] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Channel Halted--
[    2.609910] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: DMA Channel Halted--
[    2.609915] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: NAK Received--
[    2.609919] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.609922] dwc2 c90c0000.usb: DMA enabled
[    2.609926] dwc2 c90c0000.usb:   dwc2_release_channel: channel 5, halt_status 4
[    2.609931] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.609934] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.609940] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.609944] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[    2.609948] dwc2 c90c0000.usb:   Speed: HIGH
[    2.609952] dwc2 c90c0000.usb:   Max packet size: 64
[    2.609955] dwc2 c90c0000.usb:   Data buffer length: 4
[    2.609959] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa87400
[    2.609964] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1f8efec0
[    2.609967] dwc2 c90c0000.usb:   Interval: 0
[    2.609973] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.609978] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.610013] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.610018] dwc2 c90c0000.usb:   Control setup transaction
[    2.610022] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.610025] dwc2 c90c0000.usb: DMA enabled
[    2.610028] dwc2 c90c0000.usb: desc DMA disabled
[    2.610032] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.610036] dwc2 c90c0000.usb: set HAINTMSK to 00000040
[    2.610040] dwc2 c90c0000.usb: set GINTMSK to f300000e
[    2.610044] dwc2 c90c0000.usb: set HCCHAR(6) to 00800040
[    2.610048] dwc2 c90c0000.usb: dwc2_hc_init: Channel 6
[    2.610051] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.610054] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.610058] dwc2 c90c0000.usb: 	 Is In: 0
[    2.610061] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.610064] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.610068] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.610072] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.610075] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.610079] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.610083] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.610086] dwc2 c90c0000.usb: no split
[    2.610091] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(6)
[    2.610095] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 6
[    2.610098] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.610101] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.610105] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.610109] dwc2 c90c0000.usb: Wrote 1f8efec0 to HCDMA(6)
[    2.610113] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.610117] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(6)
[    2.610127] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.610131] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.610135] dwc2 c90c0000.usb: HAINT=00000040
[    2.610139] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 6
[    2.610144] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.610148] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Channel Halted--
[    2.610152] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: DMA Channel Halted--
[    2.610156] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Transfer Complete--
[    2.610160] dwc2 c90c0000.usb:   Control setup transaction done
[    2.610163] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.610168] dwc2 c90c0000.usb:   dwc2_release_channel: channel 6, halt_status 1
[    2.610172] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.610175] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.610179] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.610182] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.610188] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.610192] dwc2 c90c0000.usb:   Control data transaction
[    2.610195] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.610199] dwc2 c90c0000.usb: DMA enabled
[    2.610202] dwc2 c90c0000.usb: desc DMA disabled
[    2.610206] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.610209] dwc2 c90c0000.usb: set HAINTMSK to 00000080
[    2.610213] dwc2 c90c0000.usb: set GINTMSK to f300000e
[    2.610217] dwc2 c90c0000.usb: set HCCHAR(7) to 00808040
[    2.610221] dwc2 c90c0000.usb: dwc2_hc_init: Channel 7
[    2.610224] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.610228] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.610231] dwc2 c90c0000.usb: 	 Is In: 1
[    2.610234] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.610238] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.610241] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.610245] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.610249] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.610253] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.610257] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.610260] dwc2 c90c0000.usb: no split
[    2.610265] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(7)
[    2.610268] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 7
[    2.610272] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.610275] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.610279] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.610283] dwc2 c90c0000.usb: Wrote 1fa87400 to HCDMA(7)
[    2.610286] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.610290] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(7)
[    2.610294] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.610299] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[    2.610539] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.610544] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.610548] dwc2 c90c0000.usb: HAINT=00000080
[    2.610553] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 7
[    2.610557] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.610563] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Channel Halted--
[    2.610567] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: DMA Channel Halted--
[    2.610571] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Transfer Complete--
[    2.610576] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4
[    2.610581] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 7
[    2.610584] dwc2 c90c0000.usb:   chan->xfer_len 64
[    2.610588] dwc2 c90c0000.usb:   hctsiz.xfersize 60
[    2.610592] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4
[    2.610595] dwc2 c90c0000.usb:   urb->actual_length 4
[    2.610599] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.610602] dwc2 c90c0000.usb:   Control data transfer done
[    2.610606] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.610610] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.610613] dwc2 c90c0000.usb: DMA enabled
[    2.610618] dwc2 c90c0000.usb:   dwc2_release_channel: channel 7, halt_status 1
[    2.610623] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.610627] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.610630] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.610634] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.610639] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.610643] dwc2 c90c0000.usb:   Control status transaction
[    2.610647] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.610651] dwc2 c90c0000.usb: DMA enabled
[    2.610654] dwc2 c90c0000.usb: desc DMA disabled
[    2.610658] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.610662] dwc2 c90c0000.usb: set HAINTMSK to 00000100
[    2.610665] dwc2 c90c0000.usb: set GINTMSK to f300000e
[    2.610670] dwc2 c90c0000.usb: set HCCHAR(8) to 00800040
[    2.610673] dwc2 c90c0000.usb: dwc2_hc_init: Channel 8
[    2.610677] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.610680] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.610683] dwc2 c90c0000.usb: 	 Is In: 0
[    2.610687] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.610690] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.610694] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.610698] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.610701] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.610705] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.610709] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.610712] dwc2 c90c0000.usb: no split
[    2.610717] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(8)
[    2.610721] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 8
[    2.610724] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.610728] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.610732] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.610736] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(8)
[    2.610739] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.610744] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(8)
[    2.610748] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.610752] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf300000e
[    2.610789] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000008
[    2.610794] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.610798] dwc2 c90c0000.usb: HAINT=00000100
[    2.610802] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 8
[    2.610806] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.610810] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Channel Halted--
[    2.610814] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: DMA Channel Halted--
[    2.610818] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Transfer Complete--
[    2.610822] dwc2 c90c0000.usb:   Control transfer complete
[    2.610828] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 4
[    2.610833] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.610838] dwc2 c90c0000.usb:   dwc2_release_channel: channel 8, halt_status 2
[    2.610842] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.610846] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.610849] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.610853] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.610858] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[    2.610911] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.610916] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.610920] dwc2 c90c0000.usb:   Device address: 2
[    2.610924] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.610928] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.610931] dwc2 c90c0000.usb:   Speed: HIGH
[    2.610935] dwc2 c90c0000.usb:   Max packet size: 64
[    2.610939] dwc2 c90c0000.usb:   Data buffer length: 4
[    2.610943] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa87400
[    2.610947] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1f8efec0
[    2.610950] dwc2 c90c0000.usb:   Interval: 0
[    2.610956] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.610962] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.611014] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.611019] dwc2 c90c0000.usb:   Control setup transaction
[    2.611023] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.611026] dwc2 c90c0000.usb: DMA enabled
[    2.611029] dwc2 c90c0000.usb: desc DMA disabled
[    2.611033] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.611037] dwc2 c90c0000.usb: set HAINTMSK to 00000200
[    2.611041] dwc2 c90c0000.usb: set GINTMSK to f300000e
[    2.611046] dwc2 c90c0000.usb: set HCCHAR(9) to 00800040
[    2.611049] dwc2 c90c0000.usb: dwc2_hc_init: Channel 9
[    2.611053] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.611056] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.611059] dwc2 c90c0000.usb: 	 Is In: 0
[    2.611063] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.611066] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.611070] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.611074] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.611078] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.611082] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.611086] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.611090] dwc2 c90c0000.usb: no split
[    2.611094] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(9)
[    2.611098] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 9
[    2.611102] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.611105] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.611109] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.611113] dwc2 c90c0000.usb: Wrote 1f8efec0 to HCDMA(9)
[    2.611116] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.611120] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(9)
[    2.611137] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000008
[    2.611142] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.611145] dwc2 c90c0000.usb: HAINT=00000200
[    2.611149] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 9
[    2.611154] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.611158] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Channel Halted--
[    2.611162] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: DMA Channel Halted--
[    2.611166] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Transfer Complete--
[    2.611170] dwc2 c90c0000.usb:   Control setup transaction done
[    2.611173] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.611178] dwc2 c90c0000.usb:   dwc2_release_channel: channel 9, halt_status 1
[    2.611182] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.611186] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.611189] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.611193] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.611197] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.611201] dwc2 c90c0000.usb:   Control data transaction
[    2.611205] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.611208] dwc2 c90c0000.usb: DMA enabled
[    2.611211] dwc2 c90c0000.usb: desc DMA disabled
[    2.611214] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.611218] dwc2 c90c0000.usb: set HAINTMSK to 00000400
[    2.611222] dwc2 c90c0000.usb: set GINTMSK to f300000e
[    2.611226] dwc2 c90c0000.usb: set HCCHAR(10) to 00808040
[    2.611230] dwc2 c90c0000.usb: dwc2_hc_init: Channel 10
[    2.611233] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.611237] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.611240] dwc2 c90c0000.usb: 	 Is In: 1
[    2.611244] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.611247] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.611251] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.611254] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.611258] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.611262] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.611266] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.611269] dwc2 c90c0000.usb: no split
[    2.611274] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(10)
[    2.611277] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 10
[    2.611281] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.611284] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.611288] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.611292] dwc2 c90c0000.usb: Wrote 1fa87400 to HCDMA(10)
[    2.611296] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.611300] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(10)
[    2.611304] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.611308] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[    2.611538] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.611543] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.611547] dwc2 c90c0000.usb: HAINT=00000400
[    2.611552] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 10
[    2.611557] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.611561] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Channel Halted--
[    2.611565] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: DMA Channel Halted--
[    2.611569] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Transfer Complete--
[    2.611574] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4
[    2.611579] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 10
[    2.611582] dwc2 c90c0000.usb:   chan->xfer_len 64
[    2.611586] dwc2 c90c0000.usb:   hctsiz.xfersize 60
[    2.611589] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4
[    2.611593] dwc2 c90c0000.usb:   urb->actual_length 4
[    2.611597] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.611600] dwc2 c90c0000.usb:   Control data transfer done
[    2.611604] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.611607] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.611610] dwc2 c90c0000.usb: DMA enabled
[    2.611615] dwc2 c90c0000.usb:   dwc2_release_channel: channel 10, halt_status 1
[    2.611619] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.611623] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.611627] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.611630] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.611635] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.611639] dwc2 c90c0000.usb:   Control status transaction
[    2.611643] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.611646] dwc2 c90c0000.usb: DMA enabled
[    2.611650] dwc2 c90c0000.usb: desc DMA disabled
[    2.611653] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.611657] dwc2 c90c0000.usb: set HAINTMSK to 00000800
[    2.611661] dwc2 c90c0000.usb: set GINTMSK to f300000e
[    2.611666] dwc2 c90c0000.usb: set HCCHAR(11) to 00800040
[    2.611669] dwc2 c90c0000.usb: dwc2_hc_init: Channel 11
[    2.611673] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.611676] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.611679] dwc2 c90c0000.usb: 	 Is In: 0
[    2.611683] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.611686] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.611689] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.611693] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.611697] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.611701] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.611705] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.611708] dwc2 c90c0000.usb: no split
[    2.611713] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(11)
[    2.611717] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 11
[    2.611721] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.611724] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.611727] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.611732] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(11)
[    2.611735] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.611740] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(11)
[    2.611744] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.611749] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf300000e
[    2.611758] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000008
[    2.611762] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.611765] dwc2 c90c0000.usb: HAINT=00000800
[    2.611769] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 11
[    2.611774] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.611778] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Channel Halted--
[    2.611782] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: DMA Channel Halted--
[    2.611786] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Transfer Complete--
[    2.611789] dwc2 c90c0000.usb:   Control transfer complete
[    2.611795] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 4
[    2.611801] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.611805] dwc2 c90c0000.usb:   dwc2_release_channel: channel 11, halt_status 2
[    2.611810] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.611813] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.611817] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.611821] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.611825] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[    2.611878] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.611889] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.611894] dwc2 c90c0000.usb:   Device address: 2
[    2.611898] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.611902] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.611905] dwc2 c90c0000.usb:   Speed: HIGH
[    2.611909] dwc2 c90c0000.usb:   Max packet size: 64
[    2.611912] dwc2 c90c0000.usb:   Data buffer length: 4
[    2.611917] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa87400
[    2.611921] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1f8efec0
[    2.611924] dwc2 c90c0000.usb:   Interval: 0
[    2.611930] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.611936] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.612016] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.612021] dwc2 c90c0000.usb:   Control setup transaction
[    2.612025] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.612028] dwc2 c90c0000.usb: DMA enabled
[    2.612032] dwc2 c90c0000.usb: desc DMA disabled
[    2.612036] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.612040] dwc2 c90c0000.usb: set HAINTMSK to 00001000
[    2.612044] dwc2 c90c0000.usb: set GINTMSK to f300000e
[    2.612048] dwc2 c90c0000.usb: set HCCHAR(12) to 00800040
[    2.612052] dwc2 c90c0000.usb: dwc2_hc_init: Channel 12
[    2.612055] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.612059] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.612062] dwc2 c90c0000.usb: 	 Is In: 0
[    2.612065] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.612069] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.612072] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.612076] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.612080] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.612083] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.612088] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.612091] dwc2 c90c0000.usb: no split
[    2.612096] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(12)
[    2.612100] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 12
[    2.612103] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.612107] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.612110] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.612114] dwc2 c90c0000.usb: Wrote 1f8efec0 to HCDMA(12)
[    2.612118] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.612122] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(12)
[    2.612131] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.612135] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.612139] dwc2 c90c0000.usb: HAINT=00001000
[    2.612143] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 12
[    2.612147] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.612152] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Channel Halted--
[    2.612156] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: DMA Channel Halted--
[    2.612160] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Transfer Complete--
[    2.612163] dwc2 c90c0000.usb:   Control setup transaction done
[    2.612167] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.612171] dwc2 c90c0000.usb:   dwc2_release_channel: channel 12, halt_status 1
[    2.612176] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.612180] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.612183] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.612187] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.612191] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.612195] dwc2 c90c0000.usb:   Control data transaction
[    2.612199] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.612202] dwc2 c90c0000.usb: DMA enabled
[    2.612206] dwc2 c90c0000.usb: desc DMA disabled
[    2.612209] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.612213] dwc2 c90c0000.usb: set HAINTMSK to 00002000
[    2.612217] dwc2 c90c0000.usb: set GINTMSK to f300000e
[    2.612222] dwc2 c90c0000.usb: set HCCHAR(13) to 00808040
[    2.612225] dwc2 c90c0000.usb: dwc2_hc_init: Channel 13
[    2.612229] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.612232] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.612235] dwc2 c90c0000.usb: 	 Is In: 1
[    2.612239] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.612242] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.612245] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.612250] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.612253] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.612257] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.612261] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.612264] dwc2 c90c0000.usb: no split
[    2.612268] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(13)
[    2.612272] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 13
[    2.612276] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.612279] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.612283] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.612287] dwc2 c90c0000.usb: Wrote 1fa87400 to HCDMA(13)
[    2.612290] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.612294] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(13)
[    2.612298] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.612303] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[    2.612528] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.612533] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.612537] dwc2 c90c0000.usb: HAINT=00002000
[    2.612542] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 13
[    2.612546] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.612550] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Channel Halted--
[    2.612554] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: DMA Channel Halted--
[    2.612558] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Transfer Complete--
[    2.612563] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4
[    2.612568] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 13
[    2.612571] dwc2 c90c0000.usb:   chan->xfer_len 64
[    2.612574] dwc2 c90c0000.usb:   hctsiz.xfersize 60
[    2.612578] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4
[    2.612582] dwc2 c90c0000.usb:   urb->actual_length 4
[    2.612586] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.612589] dwc2 c90c0000.usb:   Control data transfer done
[    2.612593] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.612597] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.612600] dwc2 c90c0000.usb: DMA enabled
[    2.612604] dwc2 c90c0000.usb:   dwc2_release_channel: channel 13, halt_status 1
[    2.612609] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.612612] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.612616] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.612619] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.612625] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.612630] dwc2 c90c0000.usb:   Control status transaction
[    2.612634] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.612637] dwc2 c90c0000.usb: DMA enabled
[    2.612640] dwc2 c90c0000.usb: desc DMA disabled
[    2.612645] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.612649] dwc2 c90c0000.usb: set HAINTMSK to 00004000
[    2.612653] dwc2 c90c0000.usb: set GINTMSK to f300000e
[    2.612657] dwc2 c90c0000.usb: set HCCHAR(14) to 00800040
[    2.612661] dwc2 c90c0000.usb: dwc2_hc_init: Channel 14
[    2.612664] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.612667] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.612671] dwc2 c90c0000.usb: 	 Is In: 0
[    2.612674] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.612677] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.612681] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.612684] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.612688] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.612692] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.612696] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.612699] dwc2 c90c0000.usb: no split
[    2.612704] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(14)
[    2.612708] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 14
[    2.612711] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.612714] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.612718] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.612723] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(14)
[    2.612727] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.612731] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(14)
[    2.612735] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.612739] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf300000e
[    2.612748] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000008
[    2.612753] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.612757] dwc2 c90c0000.usb: HAINT=00004000
[    2.612761] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 14
[    2.612765] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.612770] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Channel Halted--
[    2.612774] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: DMA Channel Halted--
[    2.612778] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Transfer Complete--
[    2.612782] dwc2 c90c0000.usb:   Control transfer complete
[    2.612788] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 4
[    2.612793] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.612798] dwc2 c90c0000.usb:   dwc2_release_channel: channel 14, halt_status 2
[    2.612802] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.612806] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.612809] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.612814] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.612818] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[    2.612864] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.612869] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.612873] dwc2 c90c0000.usb:   Device address: 2
[    2.612877] dwc2 c90c0000.usb:   Endpoint: 0, IN
[    2.612887] dwc2 c90c0000.usb:   Endpoint type: CONTROL IN (IN)
[    2.612892] dwc2 c90c0000.usb:   Speed: HIGH
[    2.612896] dwc2 c90c0000.usb:   Max packet size: 64
[    2.612899] dwc2 c90c0000.usb:   Data buffer length: 4
[    2.612904] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa87400
[    2.612908] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1f8efec0
[    2.612911] dwc2 c90c0000.usb:   Interval: 0
[    2.612917] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=80, ep_type=0, mps=64
[    2.612922] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.613016] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.613022] dwc2 c90c0000.usb:   Control setup transaction
[    2.613026] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.613029] dwc2 c90c0000.usb: DMA enabled
[    2.613032] dwc2 c90c0000.usb: desc DMA disabled
[    2.613037] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.613041] dwc2 c90c0000.usb: set HAINTMSK to 00008000
[    2.613045] dwc2 c90c0000.usb: set GINTMSK to f300000e
[    2.613050] dwc2 c90c0000.usb: set HCCHAR(15) to 00800040
[    2.613054] dwc2 c90c0000.usb: dwc2_hc_init: Channel 15
[    2.613057] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.613060] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.613064] dwc2 c90c0000.usb: 	 Is In: 0
[    2.613067] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.613071] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.613074] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.613078] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.613082] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.613086] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.613090] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.613093] dwc2 c90c0000.usb: no split
[    2.613098] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(15)
[    2.613102] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 15
[    2.613106] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.613109] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.613112] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.613117] dwc2 c90c0000.usb: Wrote 1f8efec0 to HCDMA(15)
[    2.613120] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.613124] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(15)
[    2.613135] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000008
[    2.613139] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.613143] dwc2 c90c0000.usb: HAINT=00008000
[    2.613147] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 15
[    2.613152] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.613156] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Channel Halted--
[    2.613161] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: DMA Channel Halted--
[    2.613165] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Transfer Complete--
[    2.613169] dwc2 c90c0000.usb:   Control setup transaction done
[    2.613172] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.613177] dwc2 c90c0000.usb:   dwc2_release_channel: channel 15, halt_status 1
[    2.613181] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.613184] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.613188] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.613192] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.613197] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.613200] dwc2 c90c0000.usb:   Control data transaction
[    2.613204] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.613207] dwc2 c90c0000.usb: DMA enabled
[    2.613210] dwc2 c90c0000.usb: desc DMA disabled
[    2.613214] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.613217] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[    2.613221] dwc2 c90c0000.usb: set GINTMSK to f300000e
[    2.613225] dwc2 c90c0000.usb: set HCCHAR(0) to 00808040
[    2.613229] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[    2.613232] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.613236] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.613239] dwc2 c90c0000.usb: 	 Is In: 1
[    2.613242] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.613246] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.613249] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.613253] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.613256] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.613260] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.613264] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.613267] dwc2 c90c0000.usb: no split
[    2.613271] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(0)
[    2.613275] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[    2.613279] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.613282] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.613285] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.613289] dwc2 c90c0000.usb: Wrote 1fa87400 to HCDMA(0)
[    2.613293] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.613297] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(0)
[    2.613301] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.613306] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[    2.613538] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.613543] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.613547] dwc2 c90c0000.usb: HAINT=00000001
[    2.613552] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[    2.613556] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.613561] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Channel Halted--
[    2.613565] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: DMA Channel Halted--
[    2.613569] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Transfer Complete--
[    2.613574] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4
[    2.613579] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 0
[    2.613583] dwc2 c90c0000.usb:   chan->xfer_len 64
[    2.613586] dwc2 c90c0000.usb:   hctsiz.xfersize 60
[    2.613590] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4
[    2.613593] dwc2 c90c0000.usb:   urb->actual_length 4
[    2.613597] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[    2.613600] dwc2 c90c0000.usb:   Control data transfer done
[    2.613604] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.613607] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.613611] dwc2 c90c0000.usb: DMA enabled
[    2.613615] dwc2 c90c0000.usb:   dwc2_release_channel: channel 0, halt_status 1
[    2.613620] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.613623] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.613627] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.613631] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.613636] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.613640] dwc2 c90c0000.usb:   Control status transaction
[    2.613644] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.613647] dwc2 c90c0000.usb: DMA enabled
[    2.613650] dwc2 c90c0000.usb: desc DMA disabled
[    2.613654] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.613658] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[    2.613662] dwc2 c90c0000.usb: set GINTMSK to f300000e
[    2.613666] dwc2 c90c0000.usb: set HCCHAR(1) to 00800040
[    2.613669] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[    2.613673] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.613676] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.613679] dwc2 c90c0000.usb: 	 Is In: 0
[    2.613683] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.613686] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.613689] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.613693] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.613697] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.613701] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.613705] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.613709] dwc2 c90c0000.usb: no split
[    2.613713] dwc2 c90c0000.usb: Wrote 40080000 to HCTSIZ(1)
[    2.613717] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[    2.613720] dwc2 c90c0000.usb: 	 Xfer Size: 0
[    2.613723] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.613727] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.613731] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(1)
[    2.613735] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.613739] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(1)
[    2.613743] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.613747] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x06000029 gintmsk=0xf300000e
[    2.613763] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000008
[    2.613768] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.613772] dwc2 c90c0000.usb: HAINT=00000002
[    2.613776] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[    2.613781] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.613785] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[    2.613789] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[    2.613793] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[    2.613796] dwc2 c90c0000.usb:   Control transfer complete
[    2.613802] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-IN status 0 actual 4
[    2.613808] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.613813] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 2
[    2.613817] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.613820] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.613824] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.613828] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.613833] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[    2.613864] dwc2 c90c0000.usb: DWC OTG HCD URB Dequeue
[    2.613874] dwc2 c90c0000.usb: urb_dequeue, urb (ptrval)
[    2.613878] dwc2 c90c0000.usb:   Device address: 2
[    2.613887] dwc2 c90c0000.usb:   Endpoint: 1, IN
[    2.613892] dwc2 c90c0000.usb:   Endpoint type: INTERRUPT IN (IN)
[    2.613895] dwc2 c90c0000.usb:   Speed: HIGH
[    2.613899] dwc2 c90c0000.usb:   Max packet size: 1
[    2.613902] dwc2 c90c0000.usb:   Data buffer length: 1
[    2.613906] dwc2 c90c0000.usb:   Transfer buffer: (ptrval), Transfer DMA: 1fa873c0
[    2.613911] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[    2.613915] dwc2 c90c0000.usb:   Interval: 2048
[    2.613920] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.613924] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.613937] dwc2 c90c0000.usb: Called usb_hcd_giveback_urb()
[    2.613941] dwc2 c90c0000.usb:   urb->status = -115
[    2.613979] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[    2.613983] dwc2 c90c0000.usb: urb_enqueue, urb (ptrval)
[    2.613987] dwc2 c90c0000.usb:   Device address: 2
[    2.613991] dwc2 c90c0000.usb:   Endpoint: 0, OUT
[    2.613995] dwc2 c90c0000.usb:   Endpoint type: CONTROL OUT (OUT)
[    2.613998] dwc2 c90c0000.usb:   Speed: HIGH
[    2.614002] dwc2 c90c0000.usb:   Max packet size: 64
[    2.614006] dwc2 c90c0000.usb:   Data buffer length: 0
[    2.614010] dwc2 c90c0000.usb:   Transfer buffer:   (null), Transfer DMA: 00000000
[    2.614015] dwc2 c90c0000.usb:   Setup buffer: (ptrval), Setup DMA: 1f8efe00
[    2.614018] dwc2 c90c0000.usb:   Interval: 0
[    2.614024] dwc2 c90c0000.usb: addr=2, ep_num=0, ep_dir=0, ep_type=0, mps=64
[    2.614030] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.614035] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.614039] dwc2 c90c0000.usb:   Control setup transaction
[    2.614043] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.614046] dwc2 c90c0000.usb: DMA enabled
[    2.614050] dwc2 c90c0000.usb: desc DMA disabled
[    2.614054] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.614058] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[    2.614061] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.614066] dwc2 c90c0000.usb: set HCCHAR(2) to 00800040
[    2.614069] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[    2.614073] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.614076] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.614079] dwc2 c90c0000.usb: 	 Is In: 0
[    2.614083] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.614086] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.614089] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.614093] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.614097] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.614101] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.614105] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.614109] dwc2 c90c0000.usb: no split
[    2.614113] dwc2 c90c0000.usb: Wrote 60080008 to HCTSIZ(2)
[    2.614117] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[    2.614120] dwc2 c90c0000.usb: 	 Xfer Size: 8
[    2.614124] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.614127] dwc2 c90c0000.usb: 	 Start PID: 3
[    2.614132] dwc2 c90c0000.usb: Wrote 1f8efe00 to HCDMA(2)
[    2.614135] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.614139] dwc2 c90c0000.usb: Wrote 80900040 to HCCHAR(2)
[    2.614148] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.614152] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.614155] dwc2 c90c0000.usb: HAINT=00000004
[    2.614159] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[    2.614164] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.614168] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[    2.614172] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[    2.614176] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[    2.614180] dwc2 c90c0000.usb:   Control setup transaction done
[    2.614184] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.614188] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 1
[    2.614192] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),0)
[    2.614196] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.614199] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.614202] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[    2.614207] dwc2 c90c0000.usb: dwc2_assign_and_init_hc((ptrval),(ptrval))
[    2.614210] dwc2 c90c0000.usb:   Control status transaction
[    2.614214] dwc2 c90c0000.usb: dwc2_hc_init()
[    2.614217] dwc2 c90c0000.usb: DMA enabled
[    2.614220] dwc2 c90c0000.usb: desc DMA disabled
[    2.614224] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[    2.614228] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[    2.614231] dwc2 c90c0000.usb: set GINTMSK to f3000006
[    2.614235] dwc2 c90c0000.usb: set HCCHAR(3) to 00808040
[    2.614239] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[    2.614243] dwc2 c90c0000.usb: 	 Dev Addr: 2
[    2.614246] dwc2 c90c0000.usb: 	 Ep Num: 0
[    2.614249] dwc2 c90c0000.usb: 	 Is In: 1
[    2.614253] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[    2.614256] dwc2 c90c0000.usb: 	 Ep Type: 0
[    2.614259] dwc2 c90c0000.usb: 	 Max Pkt: 64
[    2.614263] dwc2 c90c0000.usb: Queue non-periodic transactions
[    2.614266] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[    2.614270] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[    2.614274] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[    2.614277] dwc2 c90c0000.usb: no split
[    2.614281] dwc2 c90c0000.usb: Wrote 40080040 to HCTSIZ(3)
[    2.614285] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[    2.614288] dwc2 c90c0000.usb: 	 Xfer Size: 64
[    2.614292] dwc2 c90c0000.usb: 	 Num Pkts: 1
[    2.614295] dwc2 c90c0000.usb: 	 Start PID: 2
[    2.614299] dwc2 c90c0000.usb: Wrote 3c040000 to HCDMA(3)
[    2.614303] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[    2.614307] dwc2 c90c0000.usb: Wrote 80908040 to HCCHAR(3)
[    2.614311] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.614315] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf3000006
[    2.614468] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[    2.614473] dwc2 c90c0000.usb: dwc2_hc_intr()
[    2.614477] dwc2 c90c0000.usb: HAINT=00000008
[    2.614482] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[    2.614486] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[    2.614491] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[    2.614495] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[    2.614499] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[    2.614502] dwc2 c90c0000.usb:   Control transfer complete
[    2.614508] dwc2 c90c0000.usb: dwc2_host_complete: urb (ptrval) device 2 ep 0-OUT status 0 actual 0
[    2.614513] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[    2.614517] dwc2 c90c0000.usb: dwc2_halt_channel()
[    2.614520] dwc2 c90c0000.usb: DMA enabled
[    2.614524] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 2
[    2.614529] dwc2 c90c0000.usb:   dwc2_deactivate_qh((ptrval),(ptrval),1)
[    2.614532] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[    2.614536] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[    2.614541] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[    2.614545] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf3000006
[    2.614575] dwc2 c90c0000.usb: SetPortFeature
[    2.614580] dwc2 c90c0000.usb: SetPortFeature - USB_PORT_FEAT_SUSPEND
[    2.614583] dwc2 c90c0000.usb: dwc2_port_suspend()
[    2.636025] dwc2 c90c0000.usb: dwc2_backup_global_registers
[    2.636034] dwc2 c90c0000.usb: dwc2_backup_host_registers
[    2.957819] EXT4-fs (mmcblk0p2): mounted filesystem with writeback data mode. Opts: (null)
[    4.447520] systemd[1]: System time before build time, advancing clock.
[    4.566661] systemd[1]: systemd 238 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN +PCRE2 default-hierarchy=hybrid)
[    4.583781] systemd[1]: Detected architecture arm.
[    4.635676] systemd[1]: Set hostname to <alarm>.
[    5.447868] systemd[1]: File /usr/lib/systemd/system/systemd-journald.service:35 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[    5.459812] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[    5.783648] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    5.818725] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    5.859672] systemd[1]: Reached target Remote File Systems.
[    5.891538] systemd[1]: Listening on Network Service Netlink Socket.
[    5.934918] systemd[1]: Listening on LVM2 poll daemon socket.
-------------- next part --------------
[  238.031721] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.031725] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.031729] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.031733] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.031737] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.031741] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.031744] dwc2 c90c0000.usb: no split
[  238.031749] dwc2 c90c0000.usb: Wrote 40080200 to HCTSIZ(15)
[  238.031752] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 15
[  238.031756] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.031759] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.031763] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.031767] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(15)
[  238.031771] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.031775] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(15)
[  238.031789] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.031793] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.031797] dwc2 c90c0000.usb: HAINT=00008000
[  238.031801] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 15
[  238.031806] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.031810] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Channel Halted--
[  238.031813] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: DMA Channel Halted--
[  238.031818] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Transfer Complete--
[  238.031821] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.031826] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.031830] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 15
[  238.031833] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.031837] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.031841] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.031844] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.031848] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.031855] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.031860] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.031863] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.031866] dwc2 c90c0000.usb: DMA enabled
[  238.031871] dwc2 c90c0000.usb:   dwc2_release_channel: channel 15, halt_status 2
[  238.031876] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.031880] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.031883] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.031888] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.031892] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.032010] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.032016] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.032020] dwc2 c90c0000.usb:   Device address: 3
[  238.032024] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.032028] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.032031] dwc2 c90c0000.usb:   Speed: HIGH
[  238.032035] dwc2 c90c0000.usb:   Max packet size: 512
[  238.032039] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.032049] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.032053] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.032057] dwc2 c90c0000.usb:   Interval: 0
[  238.032063] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.032068] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.032174] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.032178] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.032182] dwc2 c90c0000.usb: DMA enabled
[  238.032185] dwc2 c90c0000.usb: desc DMA disabled
[  238.032189] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.032193] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[  238.032196] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.032201] dwc2 c90c0000.usb: set HCCHAR(1) to 00c80a00
[  238.032204] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[  238.032208] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.032211] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.032215] dwc2 c90c0000.usb: 	 Is In: 0
[  238.032218] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.032222] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.032225] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.032229] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.032233] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.032236] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.032240] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.032244] dwc2 c90c0000.usb: no split
[  238.032248] dwc2 c90c0000.usb: Wrote 0008001f to HCTSIZ(1)
[  238.032252] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[  238.032256] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.032259] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.032263] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.032267] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(1)
[  238.032271] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.032275] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(1)
[  238.032285] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.032288] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.032292] dwc2 c90c0000.usb: HAINT=00000002
[  238.032296] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[  238.032301] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.032305] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[  238.032309] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[  238.032313] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[  238.032317] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.032321] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.032326] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 1
[  238.032329] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.032333] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.032336] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.032340] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.032344] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.032350] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.032356] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.032360] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 2
[  238.032366] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.032370] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.032373] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.032378] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.032382] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.032411] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.032416] dwc2 c90c0000.usb: urb_enqueue, urb c60a6a1a
[  238.032425] dwc2 c90c0000.usb:   Device address: 3
[  238.032428] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.032432] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.032436] dwc2 c90c0000.usb:   Speed: HIGH
[  238.032440] dwc2 c90c0000.usb:   Max packet size: 512
[  238.032444] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.032449] dwc2 c90c0000.usb:   Transfer buffer: 23465f23, Transfer DMA: 1f853000
[  238.032454] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.032457] dwc2 c90c0000.usb:   Interval: 0
[  238.032463] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.032468] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.032548] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.032552] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.032556] dwc2 c90c0000.usb: DMA enabled
[  238.032559] dwc2 c90c0000.usb: desc DMA disabled
[  238.032563] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.032567] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[  238.032570] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.032575] dwc2 c90c0000.usb: set HCCHAR(2) to 00c89200
[  238.032578] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[  238.032582] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.032585] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.032589] dwc2 c90c0000.usb: 	 Is In: 1
[  238.032592] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.032596] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.032599] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.032603] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.032607] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.032611] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.032615] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.032618] dwc2 c90c0000.usb: no split
[  238.032622] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(2)
[  238.032626] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[  238.032630] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.032633] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.032637] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.032641] dwc2 c90c0000.usb: Wrote 1f853000 to HCDMA(2)
[  238.032645] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.032649] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(2)
[  238.032750] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.032754] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.032758] dwc2 c90c0000.usb: HAINT=00000004
[  238.032763] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[  238.032767] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.032771] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[  238.032775] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[  238.032780] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[  238.032783] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.032788] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.032792] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 2
[  238.032796] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.032799] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.032803] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.032806] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.032810] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.032816] dwc2 c90c0000.usb: dwc2_host_complete: urb c60a6a1a device 3 ep 2-IN status 0 actual 4096
[  238.032821] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.032825] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.032829] dwc2 c90c0000.usb: DMA enabled
[  238.032833] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 2
[  238.032838] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.032842] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.032845] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.032850] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.032854] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.032883] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.032889] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.032892] dwc2 c90c0000.usb:   Device address: 3
[  238.032896] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.032900] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.032904] dwc2 c90c0000.usb:   Speed: HIGH
[  238.032908] dwc2 c90c0000.usb:   Max packet size: 512
[  238.032911] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.032916] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.032925] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.032928] dwc2 c90c0000.usb:   Interval: 0
[  238.032935] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.032940] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.033048] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.033052] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.033055] dwc2 c90c0000.usb: DMA enabled
[  238.033059] dwc2 c90c0000.usb: desc DMA disabled
[  238.033062] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.033066] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[  238.033070] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.033074] dwc2 c90c0000.usb: set HCCHAR(3) to 00c89200
[  238.033078] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[  238.033081] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.033085] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.033088] dwc2 c90c0000.usb: 	 Is In: 1
[  238.033092] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.033095] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.033099] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.033102] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.033106] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.033110] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.033114] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.033118] dwc2 c90c0000.usb: no split
[  238.033122] dwc2 c90c0000.usb: Wrote 00080200 to HCTSIZ(3)
[  238.033126] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[  238.033129] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.033133] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.033136] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.033141] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(3)
[  238.033145] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.033149] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(3)
[  238.033158] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.033162] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.033166] dwc2 c90c0000.usb: HAINT=00000008
[  238.033170] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[  238.033175] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.033179] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[  238.033183] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[  238.033187] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[  238.033190] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.033195] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.033199] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 3
[  238.033203] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.033206] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.033210] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.033213] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.033217] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.033223] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.033228] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.033232] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.033235] dwc2 c90c0000.usb: DMA enabled
[  238.033239] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 2
[  238.033245] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.033248] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.033252] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.033256] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.033260] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.033384] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.033391] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.033395] dwc2 c90c0000.usb:   Device address: 3
[  238.033399] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.033403] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.033406] dwc2 c90c0000.usb:   Speed: HIGH
[  238.033410] dwc2 c90c0000.usb:   Max packet size: 512
[  238.033414] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.033424] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.033428] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.033436] dwc2 c90c0000.usb:   Interval: 0
[  238.033442] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.033447] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.033548] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.033552] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.033556] dwc2 c90c0000.usb: DMA enabled
[  238.033559] dwc2 c90c0000.usb: desc DMA disabled
[  238.033563] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.033567] dwc2 c90c0000.usb: set HAINTMSK to 00000010
[  238.033571] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.033575] dwc2 c90c0000.usb: set HCCHAR(4) to 00c80a00
[  238.033579] dwc2 c90c0000.usb: dwc2_hc_init: Channel 4
[  238.033582] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.033586] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.033589] dwc2 c90c0000.usb: 	 Is In: 0
[  238.033593] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.033596] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.033599] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.033604] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.033608] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.033612] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.033616] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.033619] dwc2 c90c0000.usb: no split
[  238.033624] dwc2 c90c0000.usb: Wrote 4008001f to HCTSIZ(4)
[  238.033628] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 4
[  238.033631] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.033635] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.033638] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.033643] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(4)
[  238.033647] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.033651] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(4)
[  238.033660] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.033665] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.033668] dwc2 c90c0000.usb: HAINT=00000010
[  238.033672] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 4
[  238.033677] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.033681] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Channel Halted--
[  238.033685] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: DMA Channel Halted--
[  238.033689] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Transfer Complete--
[  238.033692] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.033704] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.033708] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 4
[  238.033711] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.033715] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.033719] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.033722] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.033726] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.033732] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.033738] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.033742] dwc2 c90c0000.usb:   dwc2_release_channel: channel 4, halt_status 2
[  238.033748] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.033751] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.033755] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.033760] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.033765] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.033804] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.033810] dwc2 c90c0000.usb: urb_enqueue, urb c60a6a1a
[  238.033814] dwc2 c90c0000.usb:   Device address: 3
[  238.033817] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.033821] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.033825] dwc2 c90c0000.usb:   Speed: HIGH
[  238.033828] dwc2 c90c0000.usb:   Max packet size: 512
[  238.033832] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.033837] dwc2 c90c0000.usb:   Transfer buffer: bfd10093, Transfer DMA: 1f87d000
[  238.033841] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.033845] dwc2 c90c0000.usb:   Interval: 0
[  238.033851] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.033856] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.033928] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.033935] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.033938] dwc2 c90c0000.usb: DMA enabled
[  238.033942] dwc2 c90c0000.usb: desc DMA disabled
[  238.033946] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.033950] dwc2 c90c0000.usb: set HAINTMSK to 00000040
[  238.033954] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.033958] dwc2 c90c0000.usb: set HCCHAR(6) to 00c89200
[  238.033962] dwc2 c90c0000.usb: dwc2_hc_init: Channel 6
[  238.033966] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.033969] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.033972] dwc2 c90c0000.usb: 	 Is In: 1
[  238.033976] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.033979] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.033983] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.033987] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.033991] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.033995] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.033999] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.034003] dwc2 c90c0000.usb: no split
[  238.034007] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(6)
[  238.034011] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 6
[  238.034015] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.034018] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.034022] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.034026] dwc2 c90c0000.usb: Wrote 1f87d000 to HCDMA(6)
[  238.034030] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.034034] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(6)
[  238.034144] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.034148] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.034152] dwc2 c90c0000.usb: HAINT=00000040
[  238.034156] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 6
[  238.034161] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.034165] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Channel Halted--
[  238.034169] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: DMA Channel Halted--
[  238.034174] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Transfer Complete--
[  238.034177] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.034182] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.034186] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 6
[  238.034190] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.034193] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.034197] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.034201] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.034204] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.034211] dwc2 c90c0000.usb: dwc2_host_complete: urb c60a6a1a device 3 ep 2-IN status 0 actual 4096
[  238.034217] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.034220] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.034224] dwc2 c90c0000.usb: DMA enabled
[  238.034228] dwc2 c90c0000.usb:   dwc2_release_channel: channel 6, halt_status 2
[  238.034233] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.034238] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.034241] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.034246] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.034251] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.034286] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.034297] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.034301] dwc2 c90c0000.usb:   Device address: 3
[  238.034305] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.034309] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.034312] dwc2 c90c0000.usb:   Speed: HIGH
[  238.034316] dwc2 c90c0000.usb:   Max packet size: 512
[  238.034320] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.034324] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.034329] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.034332] dwc2 c90c0000.usb:   Interval: 0
[  238.034338] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.034343] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.034424] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.034428] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.034432] dwc2 c90c0000.usb: DMA enabled
[  238.034435] dwc2 c90c0000.usb: desc DMA disabled
[  238.034439] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.034443] dwc2 c90c0000.usb: set HAINTMSK to 00000020
[  238.034447] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.034451] dwc2 c90c0000.usb: set HCCHAR(5) to 00c89200
[  238.034455] dwc2 c90c0000.usb: dwc2_hc_init: Channel 5
[  238.034458] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.034462] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.034465] dwc2 c90c0000.usb: 	 Is In: 1
[  238.034469] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.034472] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.034476] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.034480] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.034484] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.034487] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.034491] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.034495] dwc2 c90c0000.usb: no split
[  238.034499] dwc2 c90c0000.usb: Wrote 40080200 to HCTSIZ(5)
[  238.034503] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 5
[  238.034507] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.034510] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.034514] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.034518] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(5)
[  238.034521] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.034525] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(5)
[  238.034535] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.034539] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.034543] dwc2 c90c0000.usb: HAINT=00000020
[  238.034547] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 5
[  238.034552] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.034556] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Channel Halted--
[  238.034560] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: DMA Channel Halted--
[  238.034564] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Transfer Complete--
[  238.034567] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.034572] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.034576] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 5
[  238.034580] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.034583] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.034587] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.034590] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.034595] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.034601] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.034605] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.034609] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.034612] dwc2 c90c0000.usb: DMA enabled
[  238.034617] dwc2 c90c0000.usb:   dwc2_release_channel: channel 5, halt_status 2
[  238.034622] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.034626] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.034629] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.034634] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.034638] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.034805] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.034812] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.034816] dwc2 c90c0000.usb:   Device address: 3
[  238.034820] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.034830] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.034834] dwc2 c90c0000.usb:   Speed: HIGH
[  238.034838] dwc2 c90c0000.usb:   Max packet size: 512
[  238.034841] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.034846] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.034850] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.034854] dwc2 c90c0000.usb:   Interval: 0
[  238.034860] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.034865] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.034924] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.034928] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.034932] dwc2 c90c0000.usb: DMA enabled
[  238.034935] dwc2 c90c0000.usb: desc DMA disabled
[  238.034939] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.034943] dwc2 c90c0000.usb: set HAINTMSK to 00000080
[  238.034947] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.034951] dwc2 c90c0000.usb: set HCCHAR(7) to 00c80a00
[  238.034955] dwc2 c90c0000.usb: dwc2_hc_init: Channel 7
[  238.034958] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.034962] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.034965] dwc2 c90c0000.usb: 	 Is In: 0
[  238.034968] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.034972] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.034975] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.034979] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.034983] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.034987] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.034991] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.034994] dwc2 c90c0000.usb: no split
[  238.034999] dwc2 c90c0000.usb: Wrote 0008001f to HCTSIZ(7)
[  238.035003] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 7
[  238.035006] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.035010] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.035013] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.035018] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(7)
[  238.035021] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.035026] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(7)
[  238.035035] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.035039] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.035043] dwc2 c90c0000.usb: HAINT=00000080
[  238.035047] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 7
[  238.035051] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.035056] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Channel Halted--
[  238.035060] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: DMA Channel Halted--
[  238.035064] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Transfer Complete--
[  238.035068] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.035072] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.035077] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 7
[  238.035080] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.035084] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.035088] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.035091] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.035095] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.035102] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.035107] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.035112] dwc2 c90c0000.usb:   dwc2_release_channel: channel 7, halt_status 2
[  238.035117] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.035121] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.035124] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.035129] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.035133] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.035165] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.035176] dwc2 c90c0000.usb: urb_enqueue, urb c60a6a1a
[  238.035180] dwc2 c90c0000.usb:   Device address: 3
[  238.035183] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.035187] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.035191] dwc2 c90c0000.usb:   Speed: HIGH
[  238.035194] dwc2 c90c0000.usb:   Max packet size: 512
[  238.035198] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.035203] dwc2 c90c0000.usb:   Transfer buffer: 6547fe41, Transfer DMA: 2e082000
[  238.035207] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.035211] dwc2 c90c0000.usb:   Interval: 0
[  238.035216] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.035221] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.035298] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.035303] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.035306] dwc2 c90c0000.usb: DMA enabled
[  238.035309] dwc2 c90c0000.usb: desc DMA disabled
[  238.035313] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.035317] dwc2 c90c0000.usb: set HAINTMSK to 00000100
[  238.035321] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.035325] dwc2 c90c0000.usb: set HCCHAR(8) to 00c89200
[  238.035329] dwc2 c90c0000.usb: dwc2_hc_init: Channel 8
[  238.035332] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.035336] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.035339] dwc2 c90c0000.usb: 	 Is In: 1
[  238.035342] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.035346] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.035349] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.035353] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.035357] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.035361] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.035365] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.035368] dwc2 c90c0000.usb: no split
[  238.035373] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(8)
[  238.035376] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 8
[  238.035380] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.035383] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.035387] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.035391] dwc2 c90c0000.usb: Wrote 2e082000 to HCDMA(8)
[  238.035395] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.035399] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(8)
[  238.035499] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.035503] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.035507] dwc2 c90c0000.usb: HAINT=00000100
[  238.035511] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 8
[  238.035516] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.035520] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Channel Halted--
[  238.035524] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: DMA Channel Halted--
[  238.035529] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Transfer Complete--
[  238.035532] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.035537] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.035541] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 8
[  238.035544] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.035548] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.035551] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.035555] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.035559] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.035565] dwc2 c90c0000.usb: dwc2_host_complete: urb c60a6a1a device 3 ep 2-IN status 0 actual 4096
[  238.035571] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.035575] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.035578] dwc2 c90c0000.usb: DMA enabled
[  238.035583] dwc2 c90c0000.usb:   dwc2_release_channel: channel 8, halt_status 2
[  238.035588] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.035592] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.035595] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.035600] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.035604] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.035636] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.035642] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.035651] dwc2 c90c0000.usb:   Device address: 3
[  238.035655] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.035659] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.035662] dwc2 c90c0000.usb:   Speed: HIGH
[  238.035671] dwc2 c90c0000.usb:   Max packet size: 512
[  238.035675] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.035680] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.035684] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.035687] dwc2 c90c0000.usb:   Interval: 0
[  238.035693] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.035698] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.035798] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.035803] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.035807] dwc2 c90c0000.usb: DMA enabled
[  238.035810] dwc2 c90c0000.usb: desc DMA disabled
[  238.035814] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.035818] dwc2 c90c0000.usb: set HAINTMSK to 00000200
[  238.035822] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.035826] dwc2 c90c0000.usb: set HCCHAR(9) to 00c89200
[  238.035830] dwc2 c90c0000.usb: dwc2_hc_init: Channel 9
[  238.035833] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.035836] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.035840] dwc2 c90c0000.usb: 	 Is In: 1
[  238.035843] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.035847] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.035850] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.035854] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.035858] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.035862] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.035866] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.035869] dwc2 c90c0000.usb: no split
[  238.035873] dwc2 c90c0000.usb: Wrote 00080200 to HCTSIZ(9)
[  238.035877] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 9
[  238.035881] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.035884] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.035888] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.035892] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(9)
[  238.035896] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.035900] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(9)
[  238.035910] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.035914] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.035917] dwc2 c90c0000.usb: HAINT=00000200
[  238.035921] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 9
[  238.035926] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.035930] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Channel Halted--
[  238.035934] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: DMA Channel Halted--
[  238.035938] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Transfer Complete--
[  238.035942] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.035947] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.035951] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 9
[  238.035954] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.035958] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.035962] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.035965] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.035969] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.035975] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.035980] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.035984] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.035987] dwc2 c90c0000.usb: DMA enabled
[  238.035991] dwc2 c90c0000.usb:   dwc2_release_channel: channel 9, halt_status 2
[  238.035996] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.036000] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.036003] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.036008] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.036012] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.036141] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.036148] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.036152] dwc2 c90c0000.usb:   Device address: 3
[  238.036156] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.036160] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.036163] dwc2 c90c0000.usb:   Speed: HIGH
[  238.036172] dwc2 c90c0000.usb:   Max packet size: 512
[  238.036176] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.036181] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.036185] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.036188] dwc2 c90c0000.usb:   Interval: 0
[  238.036194] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.036199] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.036299] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.036303] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.036307] dwc2 c90c0000.usb: DMA enabled
[  238.036310] dwc2 c90c0000.usb: desc DMA disabled
[  238.036314] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.036318] dwc2 c90c0000.usb: set HAINTMSK to 00000400
[  238.036322] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.036326] dwc2 c90c0000.usb: set HCCHAR(10) to 00c80a00
[  238.036330] dwc2 c90c0000.usb: dwc2_hc_init: Channel 10
[  238.036333] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.036337] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.036340] dwc2 c90c0000.usb: 	 Is In: 0
[  238.036344] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.036347] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.036351] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.036355] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.036358] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.036362] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.036366] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.036370] dwc2 c90c0000.usb: no split
[  238.036374] dwc2 c90c0000.usb: Wrote 4008001f to HCTSIZ(10)
[  238.036378] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 10
[  238.036382] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.036385] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.036388] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.036393] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(10)
[  238.036396] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.036400] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(10)
[  238.036411] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.036415] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.036418] dwc2 c90c0000.usb: HAINT=00000400
[  238.036422] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 10
[  238.036433] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.036437] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Channel Halted--
[  238.036441] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: DMA Channel Halted--
[  238.036446] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Transfer Complete--
[  238.036449] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.036454] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.036458] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 10
[  238.036462] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.036465] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.036469] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.036472] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.036476] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.036483] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.036487] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.036492] dwc2 c90c0000.usb:   dwc2_release_channel: channel 10, halt_status 2
[  238.036497] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.036501] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.036504] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.036509] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.036514] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.036549] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.036556] dwc2 c90c0000.usb: urb_enqueue, urb c60a6a1a
[  238.036559] dwc2 c90c0000.usb:   Device address: 3
[  238.036563] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.036567] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.036571] dwc2 c90c0000.usb:   Speed: HIGH
[  238.036575] dwc2 c90c0000.usb:   Max packet size: 512
[  238.036578] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.036583] dwc2 c90c0000.usb:   Transfer buffer: 47f3efb6, Transfer DMA: 1fd75000
[  238.036587] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.036591] dwc2 c90c0000.usb:   Interval: 0
[  238.036596] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.036602] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.036674] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.036678] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.036682] dwc2 c90c0000.usb: DMA enabled
[  238.036685] dwc2 c90c0000.usb: desc DMA disabled
[  238.036689] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.036693] dwc2 c90c0000.usb: set HAINTMSK to 00000800
[  238.036697] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.036702] dwc2 c90c0000.usb: set HCCHAR(11) to 00c89200
[  238.036705] dwc2 c90c0000.usb: dwc2_hc_init: Channel 11
[  238.036709] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.036712] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.036716] dwc2 c90c0000.usb: 	 Is In: 1
[  238.036719] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.036723] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.036726] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.036730] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.036734] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.036737] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.036742] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.036745] dwc2 c90c0000.usb: no split
[  238.036750] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(11)
[  238.036754] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 11
[  238.036757] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.036761] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.036764] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.036768] dwc2 c90c0000.usb: Wrote 1fd75000 to HCDMA(11)
[  238.036772] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.036777] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(11)
[  238.036880] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.036884] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.036888] dwc2 c90c0000.usb: HAINT=00000800
[  238.036892] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 11
[  238.036897] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.036901] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Channel Halted--
[  238.036904] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: DMA Channel Halted--
[  238.036909] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Transfer Complete--
[  238.036912] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.036916] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.036921] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 11
[  238.036924] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.036928] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.036931] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.036935] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.036939] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.036945] dwc2 c90c0000.usb: dwc2_host_complete: urb c60a6a1a device 3 ep 2-IN status 0 actual 4096
[  238.036951] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.036955] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.036958] dwc2 c90c0000.usb: DMA enabled
[  238.036963] dwc2 c90c0000.usb:   dwc2_release_channel: channel 11, halt_status 2
[  238.036968] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.036972] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.036975] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.036980] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.036984] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.037014] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.037019] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.037023] dwc2 c90c0000.usb:   Device address: 3
[  238.037026] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.037030] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.037034] dwc2 c90c0000.usb:   Speed: HIGH
[  238.037037] dwc2 c90c0000.usb:   Max packet size: 512
[  238.037046] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.037051] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.037055] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.037059] dwc2 c90c0000.usb:   Interval: 0
[  238.037065] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.037070] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.037173] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.037177] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.037181] dwc2 c90c0000.usb: DMA enabled
[  238.037185] dwc2 c90c0000.usb: desc DMA disabled
[  238.037189] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.037193] dwc2 c90c0000.usb: set HAINTMSK to 00001000
[  238.037203] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.037207] dwc2 c90c0000.usb: set HCCHAR(12) to 00c89200
[  238.037211] dwc2 c90c0000.usb: dwc2_hc_init: Channel 12
[  238.037214] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.037218] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.037221] dwc2 c90c0000.usb: 	 Is In: 1
[  238.037225] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.037228] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.037232] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.037235] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.037239] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.037243] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.037247] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.037250] dwc2 c90c0000.usb: no split
[  238.037255] dwc2 c90c0000.usb: Wrote 40080200 to HCTSIZ(12)
[  238.037259] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 12
[  238.037262] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.037266] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.037269] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.037273] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(12)
[  238.037277] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.037281] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(12)
[  238.037300] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.037304] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.037308] dwc2 c90c0000.usb: HAINT=00001000
[  238.037312] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 12
[  238.037317] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.037321] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Channel Halted--
[  238.037325] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: DMA Channel Halted--
[  238.037329] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Transfer Complete--
[  238.037332] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.037336] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.037341] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 12
[  238.037344] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.037348] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.037351] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.037355] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.037359] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.037365] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.037370] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.037373] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.037376] dwc2 c90c0000.usb: DMA enabled
[  238.037381] dwc2 c90c0000.usb:   dwc2_release_channel: channel 12, halt_status 2
[  238.037386] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.037389] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.037393] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.037397] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.037401] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.037611] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.037619] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.037623] dwc2 c90c0000.usb:   Device address: 3
[  238.037627] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.037631] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.037634] dwc2 c90c0000.usb:   Speed: HIGH
[  238.037638] dwc2 c90c0000.usb:   Max packet size: 512
[  238.037642] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.037647] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.037651] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.037654] dwc2 c90c0000.usb:   Interval: 0
[  238.037661] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.037666] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.037675] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.037680] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.037684] dwc2 c90c0000.usb: DMA enabled
[  238.037687] dwc2 c90c0000.usb: desc DMA disabled
[  238.037690] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.037694] dwc2 c90c0000.usb: set HAINTMSK to 00002000
[  238.037698] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.037703] dwc2 c90c0000.usb: set HCCHAR(13) to 00c80a00
[  238.037706] dwc2 c90c0000.usb: dwc2_hc_init: Channel 13
[  238.037710] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.037713] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.037717] dwc2 c90c0000.usb: 	 Is In: 0
[  238.037720] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.037724] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.037727] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.037731] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.037735] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.037739] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.037743] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.037746] dwc2 c90c0000.usb: no split
[  238.037751] dwc2 c90c0000.usb: Wrote 0008001f to HCTSIZ(13)
[  238.037755] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 13
[  238.037758] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.037761] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.037765] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.037769] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(13)
[  238.037773] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.037777] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(13)
[  238.037786] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.037790] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.037793] dwc2 c90c0000.usb: HAINT=00002000
[  238.037797] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 13
[  238.037802] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.037806] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Channel Halted--
[  238.037810] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: DMA Channel Halted--
[  238.037814] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Transfer Complete--
[  238.037818] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.037823] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.037828] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 13
[  238.037831] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.037835] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.037838] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.037842] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.037846] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.037852] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.037858] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.037862] dwc2 c90c0000.usb:   dwc2_release_channel: channel 13, halt_status 2
[  238.037868] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.037871] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.037875] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.037879] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.037884] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.037905] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.037910] dwc2 c90c0000.usb: urb_enqueue, urb c60a6a1a
[  238.037914] dwc2 c90c0000.usb:   Device address: 3
[  238.037922] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.037926] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.037929] dwc2 c90c0000.usb:   Speed: HIGH
[  238.037933] dwc2 c90c0000.usb:   Max packet size: 512
[  238.037937] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.037941] dwc2 c90c0000.usb:   Transfer buffer: 277ed9e7, Transfer DMA: 2d035000
[  238.037946] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.037950] dwc2 c90c0000.usb:   Interval: 0
[  238.037955] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.037960] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.038049] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.038053] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.038057] dwc2 c90c0000.usb: DMA enabled
[  238.038060] dwc2 c90c0000.usb: desc DMA disabled
[  238.038064] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.038068] dwc2 c90c0000.usb: set HAINTMSK to 00004000
[  238.038072] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.038076] dwc2 c90c0000.usb: set HCCHAR(14) to 00c89200
[  238.038080] dwc2 c90c0000.usb: dwc2_hc_init: Channel 14
[  238.038083] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.038087] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.038090] dwc2 c90c0000.usb: 	 Is In: 1
[  238.038093] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.038097] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.038100] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.038104] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.038108] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.038112] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.038116] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.038119] dwc2 c90c0000.usb: no split
[  238.038123] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(14)
[  238.038127] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 14
[  238.038131] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.038134] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.038138] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.038142] dwc2 c90c0000.usb: Wrote 2d035000 to HCDMA(14)
[  238.038146] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.038150] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(14)
[  238.039011] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.039015] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.039019] dwc2 c90c0000.usb: HAINT=00004000
[  238.039023] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 14
[  238.039028] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.039032] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Channel Halted--
[  238.039036] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: DMA Channel Halted--
[  238.039041] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Transfer Complete--
[  238.039044] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.039049] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.039053] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 14
[  238.039057] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.039060] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.039064] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.039067] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.039071] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.039078] dwc2 c90c0000.usb: dwc2_host_complete: urb c60a6a1a device 3 ep 2-IN status 0 actual 4096
[  238.039083] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.039087] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.039090] dwc2 c90c0000.usb: DMA enabled
[  238.039095] dwc2 c90c0000.usb:   dwc2_release_channel: channel 14, halt_status 2
[  238.039100] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.039103] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.039107] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.039111] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.039116] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.039149] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.039154] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.039158] dwc2 c90c0000.usb:   Device address: 3
[  238.039162] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.039171] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.039174] dwc2 c90c0000.usb:   Speed: HIGH
[  238.039178] dwc2 c90c0000.usb:   Max packet size: 512
[  238.039182] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.039187] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.039191] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.039195] dwc2 c90c0000.usb:   Interval: 0
[  238.039201] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.039206] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.039298] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.039303] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.039306] dwc2 c90c0000.usb: DMA enabled
[  238.039309] dwc2 c90c0000.usb: desc DMA disabled
[  238.039313] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.039317] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[  238.039321] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.039325] dwc2 c90c0000.usb: set HCCHAR(0) to 00c89200
[  238.039329] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[  238.039332] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.039336] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.039339] dwc2 c90c0000.usb: 	 Is In: 1
[  238.039342] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.039346] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.039349] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.039353] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.039357] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.039361] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.039365] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.039368] dwc2 c90c0000.usb: no split
[  238.039373] dwc2 c90c0000.usb: Wrote 00080200 to HCTSIZ(0)
[  238.039377] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[  238.039380] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.039384] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.039387] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.039391] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(0)
[  238.039395] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.039399] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(0)
[  238.039410] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.039414] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.039417] dwc2 c90c0000.usb: HAINT=00000001
[  238.039421] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[  238.039426] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.039430] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Channel Halted--
[  238.039433] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: DMA Channel Halted--
[  238.039438] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Transfer Complete--
[  238.039441] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.039445] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.039450] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 0
[  238.039453] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.039457] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.039460] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.039464] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.039468] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.039474] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.039479] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.039483] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.039486] dwc2 c90c0000.usb: DMA enabled
[  238.039490] dwc2 c90c0000.usb:   dwc2_release_channel: channel 0, halt_status 2
[  238.039501] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.039505] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.039509] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.039514] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.039518] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.039692] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.039699] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.039704] dwc2 c90c0000.usb:   Device address: 3
[  238.039708] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.039712] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.039715] dwc2 c90c0000.usb:   Speed: HIGH
[  238.039719] dwc2 c90c0000.usb:   Max packet size: 512
[  238.039723] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.039727] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.039732] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.039735] dwc2 c90c0000.usb:   Interval: 0
[  238.039741] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.039746] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.039798] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.039802] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.039805] dwc2 c90c0000.usb: DMA enabled
[  238.039809] dwc2 c90c0000.usb: desc DMA disabled
[  238.039813] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.039817] dwc2 c90c0000.usb: set HAINTMSK to 00008000
[  238.039820] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.039825] dwc2 c90c0000.usb: set HCCHAR(15) to 00c80a00
[  238.039828] dwc2 c90c0000.usb: dwc2_hc_init: Channel 15
[  238.039832] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.039835] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.039839] dwc2 c90c0000.usb: 	 Is In: 0
[  238.039843] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.039846] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.039850] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.039853] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.039857] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.039861] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.039865] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.039868] dwc2 c90c0000.usb: no split
[  238.039873] dwc2 c90c0000.usb: Wrote 4008001f to HCTSIZ(15)
[  238.039877] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 15
[  238.039880] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.039884] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.039887] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.039892] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(15)
[  238.039896] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.039900] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(15)
[  238.039909] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.039913] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.039917] dwc2 c90c0000.usb: HAINT=00008000
[  238.039922] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 15
[  238.039926] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.039931] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Channel Halted--
[  238.039934] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: DMA Channel Halted--
[  238.039939] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Transfer Complete--
[  238.039942] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.039947] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.039951] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 15
[  238.039955] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.039958] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.039962] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.039965] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.039969] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.039976] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.039981] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.039985] dwc2 c90c0000.usb:   dwc2_release_channel: channel 15, halt_status 2
[  238.039990] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.039994] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.039997] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.040002] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.040006] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.040037] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.040047] dwc2 c90c0000.usb: urb_enqueue, urb c60a6a1a
[  238.040051] dwc2 c90c0000.usb:   Device address: 3
[  238.040054] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.040059] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.040062] dwc2 c90c0000.usb:   Speed: HIGH
[  238.040066] dwc2 c90c0000.usb:   Max packet size: 512
[  238.040069] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.040074] dwc2 c90c0000.usb:   Transfer buffer: 1286db66, Transfer DMA: 2d003000
[  238.040079] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.040082] dwc2 c90c0000.usb:   Interval: 0
[  238.040088] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.040093] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.040174] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.040178] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.040182] dwc2 c90c0000.usb: DMA enabled
[  238.040185] dwc2 c90c0000.usb: desc DMA disabled
[  238.040189] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.040192] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[  238.040196] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.040200] dwc2 c90c0000.usb: set HCCHAR(1) to 00c89200
[  238.040204] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[  238.040208] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.040211] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.040214] dwc2 c90c0000.usb: 	 Is In: 1
[  238.040218] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.040221] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.040225] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.040229] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.040232] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.040236] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.040240] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.040243] dwc2 c90c0000.usb: no split
[  238.040248] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(1)
[  238.040251] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[  238.040255] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.040258] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.040262] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.040266] dwc2 c90c0000.usb: Wrote 2d003000 to HCDMA(1)
[  238.040270] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.040274] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(1)
[  238.040374] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.040378] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.040382] dwc2 c90c0000.usb: HAINT=00000002
[  238.040386] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[  238.040391] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.040395] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[  238.040399] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[  238.040404] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[  238.040407] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.040412] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.040416] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 1
[  238.040420] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.040423] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.040427] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.040430] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.040434] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.040440] dwc2 c90c0000.usb: dwc2_host_complete: urb c60a6a1a device 3 ep 2-IN status 0 actual 4096
[  238.040446] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.040449] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.040453] dwc2 c90c0000.usb: DMA enabled
[  238.040457] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 2
[  238.040462] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.040466] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.040469] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.040474] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.040478] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.040507] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.040513] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.040516] dwc2 c90c0000.usb:   Device address: 3
[  238.040520] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.040524] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.040528] dwc2 c90c0000.usb:   Speed: HIGH
[  238.040532] dwc2 c90c0000.usb:   Max packet size: 512
[  238.040536] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.040540] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.040549] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.040553] dwc2 c90c0000.usb:   Interval: 0
[  238.040560] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.040564] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.040673] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.040678] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.040681] dwc2 c90c0000.usb: DMA enabled
[  238.040684] dwc2 c90c0000.usb: desc DMA disabled
[  238.040688] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.040692] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[  238.040696] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.040700] dwc2 c90c0000.usb: set HCCHAR(2) to 00c89200
[  238.040704] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[  238.040708] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.040711] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.040715] dwc2 c90c0000.usb: 	 Is In: 1
[  238.040718] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.040721] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.040725] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.040729] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.040733] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.040736] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.040740] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.040743] dwc2 c90c0000.usb: no split
[  238.040748] dwc2 c90c0000.usb: Wrote 40080200 to HCTSIZ(2)
[  238.040752] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[  238.040755] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.040759] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.040762] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.040766] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(2)
[  238.040770] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.040774] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(2)
[  238.040784] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.040788] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.040791] dwc2 c90c0000.usb: HAINT=00000004
[  238.040795] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[  238.040800] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.040804] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[  238.040808] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[  238.040812] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[  238.040815] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.040820] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.040824] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 2
[  238.040828] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.040831] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.040835] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.040838] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.040842] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.040848] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.040853] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.040856] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.040859] dwc2 c90c0000.usb: DMA enabled
[  238.040864] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 2
[  238.040869] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.040873] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.040876] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.040881] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.040885] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.041013] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.041020] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.041024] dwc2 c90c0000.usb:   Device address: 3
[  238.041028] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.041032] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.041035] dwc2 c90c0000.usb:   Speed: HIGH
[  238.041039] dwc2 c90c0000.usb:   Max packet size: 512
[  238.041055] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.041060] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.041064] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.041074] dwc2 c90c0000.usb:   Interval: 0
[  238.041080] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.041084] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.041174] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.041179] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.041182] dwc2 c90c0000.usb: DMA enabled
[  238.041186] dwc2 c90c0000.usb: desc DMA disabled
[  238.041189] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.041193] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[  238.041197] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.041201] dwc2 c90c0000.usb: set HCCHAR(3) to 00c80a00
[  238.041205] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[  238.041209] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.041212] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.041215] dwc2 c90c0000.usb: 	 Is In: 0
[  238.041219] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.041222] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.041226] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.041230] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.041233] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.041237] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.041241] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.041244] dwc2 c90c0000.usb: no split
[  238.041249] dwc2 c90c0000.usb: Wrote 0008001f to HCTSIZ(3)
[  238.041253] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[  238.041256] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.041260] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.041263] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.041267] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(3)
[  238.041271] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.041275] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(3)
[  238.041285] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.041289] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.041292] dwc2 c90c0000.usb: HAINT=00000008
[  238.041296] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[  238.041301] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.041305] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[  238.041309] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[  238.041313] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[  238.041317] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.041321] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.041326] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 3
[  238.041329] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.041333] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.041336] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.041340] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.041344] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.041350] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.041355] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.041360] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 2
[  238.041365] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.041368] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.041372] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.041377] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.041381] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.041411] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.041416] dwc2 c90c0000.usb: urb_enqueue, urb c60a6a1a
[  238.041425] dwc2 c90c0000.usb:   Device address: 3
[  238.041429] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.041432] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.041436] dwc2 c90c0000.usb:   Speed: HIGH
[  238.041440] dwc2 c90c0000.usb:   Max packet size: 512
[  238.041444] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.041448] dwc2 c90c0000.usb:   Transfer buffer: d8bc43c8, Transfer DMA: 1fff6000
[  238.041453] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.041457] dwc2 c90c0000.usb:   Interval: 0
[  238.041462] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.041467] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.041548] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.041553] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.041556] dwc2 c90c0000.usb: DMA enabled
[  238.041560] dwc2 c90c0000.usb: desc DMA disabled
[  238.041563] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.041567] dwc2 c90c0000.usb: set HAINTMSK to 00000010
[  238.041571] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.041575] dwc2 c90c0000.usb: set HCCHAR(4) to 00c89200
[  238.041579] dwc2 c90c0000.usb: dwc2_hc_init: Channel 4
[  238.041582] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.041586] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.041589] dwc2 c90c0000.usb: 	 Is In: 1
[  238.041593] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.041596] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.041600] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.041604] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.041607] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.041611] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.041615] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.041619] dwc2 c90c0000.usb: no split
[  238.041623] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(4)
[  238.041627] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 4
[  238.041631] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.041634] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.041637] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.041642] dwc2 c90c0000.usb: Wrote 1fff6000 to HCDMA(4)
[  238.041645] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.041649] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(4)
[  238.041751] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.041755] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.041759] dwc2 c90c0000.usb: HAINT=00000010
[  238.041763] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 4
[  238.041767] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.041772] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Channel Halted--
[  238.041776] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: DMA Channel Halted--
[  238.041780] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Transfer Complete--
[  238.041783] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.041788] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.041792] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 4
[  238.041796] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.041800] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.041803] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.041807] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.041811] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.041817] dwc2 c90c0000.usb: dwc2_host_complete: urb c60a6a1a device 3 ep 2-IN status 0 actual 4096
[  238.041822] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.041826] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.041829] dwc2 c90c0000.usb: DMA enabled
[  238.041834] dwc2 c90c0000.usb:   dwc2_release_channel: channel 4, halt_status 2
[  238.041839] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.041843] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.041846] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.041851] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.041855] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.041889] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.041895] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.041898] dwc2 c90c0000.usb:   Device address: 3
[  238.041902] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.041906] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.041909] dwc2 c90c0000.usb:   Speed: HIGH
[  238.041913] dwc2 c90c0000.usb:   Max packet size: 512
[  238.041922] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.041927] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.041931] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.041935] dwc2 c90c0000.usb:   Interval: 0
[  238.041941] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.041946] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.042048] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.042052] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.042056] dwc2 c90c0000.usb: DMA enabled
[  238.042059] dwc2 c90c0000.usb: desc DMA disabled
[  238.042063] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.042067] dwc2 c90c0000.usb: set HAINTMSK to 00000040
[  238.042070] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.042075] dwc2 c90c0000.usb: set HCCHAR(6) to 00c89200
[  238.042078] dwc2 c90c0000.usb: dwc2_hc_init: Channel 6
[  238.042082] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.042085] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.042089] dwc2 c90c0000.usb: 	 Is In: 1
[  238.042092] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.042096] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.042099] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.042103] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.042107] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.042110] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.042114] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.042118] dwc2 c90c0000.usb: no split
[  238.042122] dwc2 c90c0000.usb: Wrote 00080200 to HCTSIZ(6)
[  238.042126] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 6
[  238.042130] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.042133] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.042137] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.042141] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(6)
[  238.042145] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.042149] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(6)
[  238.042158] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.042162] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.042165] dwc2 c90c0000.usb: HAINT=00000040
[  238.042169] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 6
[  238.042174] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.042178] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Channel Halted--
[  238.042182] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: DMA Channel Halted--
[  238.042186] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Transfer Complete--
[  238.042189] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.042194] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.042198] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 6
[  238.042202] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.042205] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.042209] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.042212] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.042216] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.042222] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.042227] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.042231] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.042234] dwc2 c90c0000.usb: DMA enabled
[  238.042239] dwc2 c90c0000.usb:   dwc2_release_channel: channel 6, halt_status 2
[  238.042244] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.042247] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.042251] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.042255] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.042260] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.042385] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.042391] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.042395] dwc2 c90c0000.usb:   Device address: 3
[  238.042400] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.042404] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.042407] dwc2 c90c0000.usb:   Speed: HIGH
[  238.042411] dwc2 c90c0000.usb:   Max packet size: 512
[  238.042414] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.042424] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.042429] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.042432] dwc2 c90c0000.usb:   Interval: 0
[  238.042438] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.042443] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.042549] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.042553] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.042556] dwc2 c90c0000.usb: DMA enabled
[  238.042560] dwc2 c90c0000.usb: desc DMA disabled
[  238.042563] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.042567] dwc2 c90c0000.usb: set HAINTMSK to 00000020
[  238.042571] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.042576] dwc2 c90c0000.usb: set HCCHAR(5) to 00c80a00
[  238.042579] dwc2 c90c0000.usb: dwc2_hc_init: Channel 5
[  238.042583] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.042586] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.042590] dwc2 c90c0000.usb: 	 Is In: 0
[  238.042593] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.042597] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.042600] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.042604] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.042608] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.042612] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.042617] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.042620] dwc2 c90c0000.usb: no split
[  238.042624] dwc2 c90c0000.usb: Wrote 4008001f to HCTSIZ(5)
[  238.042628] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 5
[  238.042632] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.042635] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.042638] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.042643] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(5)
[  238.042646] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.042650] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(5)
[  238.042661] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.042664] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.042668] dwc2 c90c0000.usb: HAINT=00000020
[  238.042672] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 5
[  238.042677] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.042681] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Channel Halted--
[  238.042685] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: DMA Channel Halted--
[  238.042689] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Transfer Complete--
[  238.042693] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.042698] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.042702] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 5
[  238.042712] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.042716] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.042719] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.042723] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.042727] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.042733] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.042739] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.042744] dwc2 c90c0000.usb:   dwc2_release_channel: channel 5, halt_status 2
[  238.042749] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.042753] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.042756] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.042761] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.042765] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.042804] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.042810] dwc2 c90c0000.usb: urb_enqueue, urb c60a6a1a
[  238.042814] dwc2 c90c0000.usb:   Device address: 3
[  238.042818] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.042822] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.042825] dwc2 c90c0000.usb:   Speed: HIGH
[  238.042829] dwc2 c90c0000.usb:   Max packet size: 512
[  238.042833] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.042837] dwc2 c90c0000.usb:   Transfer buffer: f63e90a7, Transfer DMA: 1ffc6000
[  238.042842] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.042845] dwc2 c90c0000.usb:   Interval: 0
[  238.042851] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.042856] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.042924] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.042929] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.042932] dwc2 c90c0000.usb: DMA enabled
[  238.042935] dwc2 c90c0000.usb: desc DMA disabled
[  238.042939] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.042943] dwc2 c90c0000.usb: set HAINTMSK to 00000080
[  238.042947] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.042952] dwc2 c90c0000.usb: set HCCHAR(7) to 00c89200
[  238.042955] dwc2 c90c0000.usb: dwc2_hc_init: Channel 7
[  238.042959] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.042962] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.042966] dwc2 c90c0000.usb: 	 Is In: 1
[  238.042969] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.042972] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.042976] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.042980] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.042983] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.042987] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.042991] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.042995] dwc2 c90c0000.usb: no split
[  238.042999] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(7)
[  238.043003] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 7
[  238.043007] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.043010] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.043014] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.043018] dwc2 c90c0000.usb: Wrote 1ffc6000 to HCDMA(7)
[  238.043021] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.043026] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(7)
[  238.043126] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.043130] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.043133] dwc2 c90c0000.usb: HAINT=00000080
[  238.043137] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 7
[  238.043142] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.043146] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Channel Halted--
[  238.043150] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: DMA Channel Halted--
[  238.043154] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Transfer Complete--
[  238.043158] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.043162] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.043166] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 7
[  238.043170] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.043173] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.043177] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.043181] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.043185] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.043190] dwc2 c90c0000.usb: dwc2_host_complete: urb c60a6a1a device 3 ep 2-IN status 0 actual 4096
[  238.043196] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.043199] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.043203] dwc2 c90c0000.usb: DMA enabled
[  238.043207] dwc2 c90c0000.usb:   dwc2_release_channel: channel 7, halt_status 2
[  238.043212] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.043216] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.043219] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.043224] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.043229] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.043257] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.043263] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.043267] dwc2 c90c0000.usb:   Device address: 3
[  238.043270] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.043274] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.043277] dwc2 c90c0000.usb:   Speed: HIGH
[  238.043282] dwc2 c90c0000.usb:   Max packet size: 512
[  238.043285] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.043290] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.043299] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.043303] dwc2 c90c0000.usb:   Interval: 0
[  238.043309] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.043314] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.043424] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.043429] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.043433] dwc2 c90c0000.usb: DMA enabled
[  238.043436] dwc2 c90c0000.usb: desc DMA disabled
[  238.043440] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.043444] dwc2 c90c0000.usb: set HAINTMSK to 00000100
[  238.043448] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.043452] dwc2 c90c0000.usb: set HCCHAR(8) to 00c89200
[  238.043456] dwc2 c90c0000.usb: dwc2_hc_init: Channel 8
[  238.043459] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.043463] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.043466] dwc2 c90c0000.usb: 	 Is In: 1
[  238.043470] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.043473] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.043477] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.043481] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.043485] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.043488] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.043492] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.043496] dwc2 c90c0000.usb: no split
[  238.043500] dwc2 c90c0000.usb: Wrote 40080200 to HCTSIZ(8)
[  238.043510] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 8
[  238.043513] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.043517] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.043521] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.043525] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(8)
[  238.043529] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.043533] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(8)
[  238.043550] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.043555] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.043558] dwc2 c90c0000.usb: HAINT=00000100
[  238.043562] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 8
[  238.043567] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.043571] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Channel Halted--
[  238.043575] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: DMA Channel Halted--
[  238.043579] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Transfer Complete--
[  238.043582] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.043587] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.043591] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 8
[  238.043595] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.043598] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.043602] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.043605] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.043609] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.043615] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.043620] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.043624] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.043627] dwc2 c90c0000.usb: DMA enabled
[  238.043632] dwc2 c90c0000.usb:   dwc2_release_channel: channel 8, halt_status 2
[  238.043637] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.043641] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.043644] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.043649] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.043653] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.043863] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.043874] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.043879] dwc2 c90c0000.usb:   Device address: 3
[  238.043883] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.043889] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.043933] dwc2 c90c0000.usb:   Speed: HIGH
[  238.043937] dwc2 c90c0000.usb:   Max packet size: 512
[  238.043941] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.043947] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.043951] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.043955] dwc2 c90c0000.usb:   Interval: 0
[  238.043962] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.043967] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.044049] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.044055] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.044058] dwc2 c90c0000.usb: DMA enabled
[  238.044062] dwc2 c90c0000.usb: desc DMA disabled
[  238.044066] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.044069] dwc2 c90c0000.usb: set HAINTMSK to 00000200
[  238.044073] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.044077] dwc2 c90c0000.usb: set HCCHAR(9) to 00c80a00
[  238.044081] dwc2 c90c0000.usb: dwc2_hc_init: Channel 9
[  238.044085] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.044088] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.044091] dwc2 c90c0000.usb: 	 Is In: 0
[  238.044095] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.044098] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.044102] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.044106] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.044110] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.044114] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.044118] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.044121] dwc2 c90c0000.usb: no split
[  238.044126] dwc2 c90c0000.usb: Wrote 0008001f to HCTSIZ(9)
[  238.044129] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 9
[  238.044133] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.044136] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.044140] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.044144] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(9)
[  238.044148] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.044152] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(9)
[  238.044162] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.044166] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.044170] dwc2 c90c0000.usb: HAINT=00000200
[  238.044174] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 9
[  238.044179] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.044183] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Channel Halted--
[  238.044187] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: DMA Channel Halted--
[  238.044191] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Transfer Complete--
[  238.044195] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.044199] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.044204] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 9
[  238.044208] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.044211] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.044215] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.044218] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.044222] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.044229] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.044235] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.044240] dwc2 c90c0000.usb:   dwc2_release_channel: channel 9, halt_status 2
[  238.044246] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.044249] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.044253] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.044258] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.044263] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.044302] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.044308] dwc2 c90c0000.usb: urb_enqueue, urb c60a6a1a
[  238.044312] dwc2 c90c0000.usb:   Device address: 3
[  238.044316] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.044320] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.044323] dwc2 c90c0000.usb:   Speed: HIGH
[  238.044327] dwc2 c90c0000.usb:   Max packet size: 512
[  238.044331] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.044336] dwc2 c90c0000.usb:   Transfer buffer: 38c73758, Transfer DMA: 1fbd8000
[  238.044340] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.044344] dwc2 c90c0000.usb:   Interval: 0
[  238.044349] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.044354] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.044424] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.044428] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.044432] dwc2 c90c0000.usb: DMA enabled
[  238.044435] dwc2 c90c0000.usb: desc DMA disabled
[  238.044439] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.044443] dwc2 c90c0000.usb: set HAINTMSK to 00000400
[  238.044447] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.044451] dwc2 c90c0000.usb: set HCCHAR(10) to 00c89200
[  238.044455] dwc2 c90c0000.usb: dwc2_hc_init: Channel 10
[  238.044459] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.044462] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.044466] dwc2 c90c0000.usb: 	 Is In: 1
[  238.044469] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.044473] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.044476] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.044480] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.044483] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.044487] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.044491] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.044495] dwc2 c90c0000.usb: no split
[  238.044499] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(10)
[  238.044503] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 10
[  238.044506] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.044510] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.044513] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.044517] dwc2 c90c0000.usb: Wrote 1fbd8000 to HCDMA(10)
[  238.044521] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.044525] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(10)
[  238.044626] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.044630] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.044633] dwc2 c90c0000.usb: HAINT=00000400
[  238.044638] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 10
[  238.044642] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.044647] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Channel Halted--
[  238.044650] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: DMA Channel Halted--
[  238.044655] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Transfer Complete--
[  238.044658] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.044663] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.044667] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 10
[  238.044671] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.044674] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.044678] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.044681] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.044685] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.044691] dwc2 c90c0000.usb: dwc2_host_complete: urb c60a6a1a device 3 ep 2-IN status 0 actual 4096
[  238.044698] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.044701] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.044705] dwc2 c90c0000.usb: DMA enabled
[  238.044710] dwc2 c90c0000.usb:   dwc2_release_channel: channel 10, halt_status 2
[  238.044715] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.044719] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.044722] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.044727] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.044731] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.044761] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.044767] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.044770] dwc2 c90c0000.usb:   Device address: 3
[  238.044774] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.044778] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.044782] dwc2 c90c0000.usb:   Speed: HIGH
[  238.044785] dwc2 c90c0000.usb:   Max packet size: 512
[  238.044789] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.044798] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.044803] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.044806] dwc2 c90c0000.usb:   Interval: 0
[  238.044812] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.044817] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.044923] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.044927] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.044931] dwc2 c90c0000.usb: DMA enabled
[  238.044934] dwc2 c90c0000.usb: desc DMA disabled
[  238.044938] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.044942] dwc2 c90c0000.usb: set HAINTMSK to 00000800
[  238.044946] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.044951] dwc2 c90c0000.usb: set HCCHAR(11) to 00c89200
[  238.044954] dwc2 c90c0000.usb: dwc2_hc_init: Channel 11
[  238.044958] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.044961] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.044965] dwc2 c90c0000.usb: 	 Is In: 1
[  238.044968] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.044972] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.044975] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.044979] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.044983] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.044986] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.044990] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.044994] dwc2 c90c0000.usb: no split
[  238.044998] dwc2 c90c0000.usb: Wrote 00080200 to HCTSIZ(11)
[  238.045002] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 11
[  238.045006] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.045009] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.045013] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.045017] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(11)
[  238.045021] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.045026] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(11)
[  238.045036] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.045040] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.045043] dwc2 c90c0000.usb: HAINT=00000800
[  238.045047] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 11
[  238.045052] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.045056] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Channel Halted--
[  238.045060] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: DMA Channel Halted--
[  238.045064] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Transfer Complete--
[  238.045068] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.045073] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.045077] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 11
[  238.045081] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.045084] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.045088] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.045091] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.045095] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.045101] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.045106] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.045110] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.045113] dwc2 c90c0000.usb: DMA enabled
[  238.045117] dwc2 c90c0000.usb:   dwc2_release_channel: channel 11, halt_status 2
[  238.045122] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.045126] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.045130] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.045134] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.045139] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.045249] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.045255] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.045260] dwc2 c90c0000.usb:   Device address: 3
[  238.045264] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.045268] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.045271] dwc2 c90c0000.usb:   Speed: HIGH
[  238.045275] dwc2 c90c0000.usb:   Max packet size: 512
[  238.045279] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.045284] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.045288] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.045297] dwc2 c90c0000.usb:   Interval: 0
[  238.045304] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.045309] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.045423] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.045428] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.045431] dwc2 c90c0000.usb: DMA enabled
[  238.045435] dwc2 c90c0000.usb: desc DMA disabled
[  238.045438] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.045442] dwc2 c90c0000.usb: set HAINTMSK to 00001000
[  238.045446] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.045450] dwc2 c90c0000.usb: set HCCHAR(12) to 00c80a00
[  238.045454] dwc2 c90c0000.usb: dwc2_hc_init: Channel 12
[  238.045458] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.045461] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.045464] dwc2 c90c0000.usb: 	 Is In: 0
[  238.045468] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.045471] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.045475] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.045479] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.045483] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.045486] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.045490] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.045494] dwc2 c90c0000.usb: no split
[  238.045498] dwc2 c90c0000.usb: Wrote 4008001f to HCTSIZ(12)
[  238.045502] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 12
[  238.045506] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.045509] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.045513] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.045517] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(12)
[  238.045521] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.045525] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(12)
[  238.045534] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.045537] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.045541] dwc2 c90c0000.usb: HAINT=00001000
[  238.045545] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 12
[  238.045550] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.045554] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Channel Halted--
[  238.045558] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: DMA Channel Halted--
[  238.045562] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Transfer Complete--
[  238.045566] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.045570] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.045574] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 12
[  238.045578] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.045582] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.045585] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.045589] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.045593] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.045599] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.045604] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.045609] dwc2 c90c0000.usb:   dwc2_release_channel: channel 12, halt_status 2
[  238.045614] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.045618] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.045622] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.045626] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.045631] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.045662] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.045673] dwc2 c90c0000.usb: urb_enqueue, urb c60a6a1a
[  238.045677] dwc2 c90c0000.usb:   Device address: 3
[  238.045680] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.045684] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.045687] dwc2 c90c0000.usb:   Speed: HIGH
[  238.045691] dwc2 c90c0000.usb:   Max packet size: 512
[  238.045695] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.045700] dwc2 c90c0000.usb:   Transfer buffer: 30517894, Transfer DMA: 2e24e000
[  238.045704] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.045708] dwc2 c90c0000.usb:   Interval: 0
[  238.045713] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.045718] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.045726] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.045730] dwc2 c90c0000.usb: urb_enqueue, urb d40f5527
[  238.045734] dwc2 c90c0000.usb:   Device address: 3
[  238.045738] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.045741] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.045745] dwc2 c90c0000.usb:   Speed: HIGH
[  238.045749] dwc2 c90c0000.usb:   Max packet size: 512
[  238.045752] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.045757] dwc2 c90c0000.usb:   Transfer buffer: 08413472, Transfer DMA: 1fcf6000
[  238.045761] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.045764] dwc2 c90c0000.usb:   Interval: 0
[  238.045770] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.045774] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.045782] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.045786] dwc2 c90c0000.usb: urb_enqueue, urb 219a56a4
[  238.045796] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.045800] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.045803] dwc2 c90c0000.usb: DMA enabled
[  238.045806] dwc2 c90c0000.usb: desc DMA disabled
[  238.045810] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.045814] dwc2 c90c0000.usb: set HAINTMSK to 00002000
[  238.045818] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.045822] dwc2 c90c0000.usb: set HCCHAR(13) to 00c89200
[  238.045826] dwc2 c90c0000.usb: dwc2_hc_init: Channel 13
[  238.045829] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.045832] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.045836] dwc2 c90c0000.usb: 	 Is In: 1
[  238.045839] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.045843] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.045846] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.045850] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.045854] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.045858] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.045862] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.045866] dwc2 c90c0000.usb: no split
[  238.045871] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(13)
[  238.045874] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 13
[  238.045878] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.045881] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.045885] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.045889] dwc2 c90c0000.usb: Wrote 2e24e000 to HCDMA(13)
[  238.045893] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.045897] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(13)
[  238.045902] dwc2 c90c0000.usb:   Device address: 3
[  238.045905] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.045909] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.045913] dwc2 c90c0000.usb:   Speed: HIGH
[  238.045921] dwc2 c90c0000.usb:   Max packet size: 512
[  238.045925] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.045930] dwc2 c90c0000.usb:   Transfer buffer: 75e9840d, Transfer DMA: 1f9f8000
[  238.045934] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.045938] dwc2 c90c0000.usb:   Interval: 0
[  238.045944] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.045949] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.046001] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.046006] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.046009] dwc2 c90c0000.usb: HAINT=00002000
[  238.046014] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 13
[  238.046018] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.046022] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Channel Halted--
[  238.046027] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: DMA Channel Halted--
[  238.046037] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Transfer Complete--
[  238.046040] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.046045] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.046050] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 13
[  238.046053] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.046057] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.046060] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.046064] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.046068] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.046074] dwc2 c90c0000.usb: dwc2_host_complete: urb c60a6a1a device 3 ep 2-IN status 0 actual 4096
[  238.046080] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.046083] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.046086] dwc2 c90c0000.usb: DMA enabled
[  238.046091] dwc2 c90c0000.usb:   dwc2_release_channel: channel 13, halt_status 2
[  238.046096] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.046100] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.046103] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.046107] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.046112] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.046116] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.046120] dwc2 c90c0000.usb: DMA enabled
[  238.046123] dwc2 c90c0000.usb: desc DMA disabled
[  238.046127] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.046131] dwc2 c90c0000.usb: set HAINTMSK to 00004000
[  238.046135] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.046139] dwc2 c90c0000.usb: set HCCHAR(14) to 00c89200
[  238.046143] dwc2 c90c0000.usb: dwc2_hc_init: Channel 14
[  238.046146] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.046149] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.046153] dwc2 c90c0000.usb: 	 Is In: 1
[  238.046156] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.046160] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.046163] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.046168] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.046171] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.046175] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.046179] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.046182] dwc2 c90c0000.usb: no split
[  238.046187] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(14)
[  238.046191] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 14
[  238.046194] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.046198] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.046202] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.046206] dwc2 c90c0000.usb: Wrote 1fcf6000 to HCDMA(14)
[  238.046210] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.046214] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(14)
[  238.046218] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.046222] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.046319] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.046323] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.046327] dwc2 c90c0000.usb: HAINT=00004000
[  238.046331] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 14
[  238.046336] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.046340] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Channel Halted--
[  238.046344] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: DMA Channel Halted--
[  238.046348] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Transfer Complete--
[  238.046351] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.046356] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.046360] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 14
[  238.046364] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.046368] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.046372] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.046376] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.046379] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.046385] dwc2 c90c0000.usb: dwc2_host_complete: urb d40f5527 device 3 ep 2-IN status 0 actual 4096
[  238.046390] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.046394] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.046397] dwc2 c90c0000.usb: DMA enabled
[  238.046401] dwc2 c90c0000.usb:   dwc2_release_channel: channel 14, halt_status 2
[  238.046406] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.046410] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.046413] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.046416] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.046422] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.046426] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.046429] dwc2 c90c0000.usb: DMA enabled
[  238.046432] dwc2 c90c0000.usb: desc DMA disabled
[  238.046436] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.046440] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[  238.046443] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.046448] dwc2 c90c0000.usb: set HCCHAR(0) to 00c89200
[  238.046451] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[  238.046455] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.046458] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.046462] dwc2 c90c0000.usb: 	 Is In: 1
[  238.046465] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.046469] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.046472] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.046476] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.046480] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.046483] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.046487] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.046491] dwc2 c90c0000.usb: no split
[  238.046495] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(0)
[  238.046499] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[  238.046502] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.046506] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.046509] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.046514] dwc2 c90c0000.usb: Wrote 1f9f8000 to HCDMA(0)
[  238.046517] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.046521] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(0)
[  238.046526] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.046530] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.046625] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.046629] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.046633] dwc2 c90c0000.usb: HAINT=00000001
[  238.046637] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[  238.046642] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.046646] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Channel Halted--
[  238.046650] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: DMA Channel Halted--
[  238.046654] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Transfer Complete--
[  238.046658] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.046662] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.046666] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 0
[  238.046670] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.046673] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.046677] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.046680] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.046684] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.046690] dwc2 c90c0000.usb: dwc2_host_complete: urb 219a56a4 device 3 ep 2-IN status 0 actual 4096
[  238.046695] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.046699] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.046702] dwc2 c90c0000.usb: DMA enabled
[  238.046706] dwc2 c90c0000.usb:   dwc2_release_channel: channel 0, halt_status 2
[  238.046711] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.046715] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.046719] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.046723] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.046728] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.046760] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.046766] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.046770] dwc2 c90c0000.usb:   Device address: 3
[  238.046773] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.046777] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.046781] dwc2 c90c0000.usb:   Speed: HIGH
[  238.046785] dwc2 c90c0000.usb:   Max packet size: 512
[  238.046788] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.046798] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.046802] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.046812] dwc2 c90c0000.usb:   Interval: 0
[  238.046818] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.046823] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.046923] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.046928] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.046932] dwc2 c90c0000.usb: DMA enabled
[  238.046935] dwc2 c90c0000.usb: desc DMA disabled
[  238.046939] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.046943] dwc2 c90c0000.usb: set HAINTMSK to 00008000
[  238.046947] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.046951] dwc2 c90c0000.usb: set HCCHAR(15) to 00c89200
[  238.046955] dwc2 c90c0000.usb: dwc2_hc_init: Channel 15
[  238.046958] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.046962] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.046965] dwc2 c90c0000.usb: 	 Is In: 1
[  238.046969] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.046972] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.046976] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.046979] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.046983] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.046987] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.046991] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.046994] dwc2 c90c0000.usb: no split
[  238.046998] dwc2 c90c0000.usb: Wrote 40080200 to HCTSIZ(15)
[  238.047002] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 15
[  238.047006] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.047009] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.047013] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.047017] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(15)
[  238.047021] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.047025] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(15)
[  238.047035] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.047039] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.047042] dwc2 c90c0000.usb: HAINT=00008000
[  238.047046] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 15
[  238.047051] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.047055] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Channel Halted--
[  238.047059] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: DMA Channel Halted--
[  238.047063] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Transfer Complete--
[  238.047066] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.047071] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.047075] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 15
[  238.047079] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.047082] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.047086] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.047089] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.047093] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.047099] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.047104] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.047108] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.047111] dwc2 c90c0000.usb: DMA enabled
[  238.047115] dwc2 c90c0000.usb:   dwc2_release_channel: channel 15, halt_status 2
[  238.047121] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.047124] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.047128] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.047132] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.047136] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.047230] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.047237] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.047241] dwc2 c90c0000.usb:   Device address: 3
[  238.047245] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.047249] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.047253] dwc2 c90c0000.usb:   Speed: HIGH
[  238.047257] dwc2 c90c0000.usb:   Max packet size: 512
[  238.047261] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.047265] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.047270] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.047273] dwc2 c90c0000.usb:   Interval: 0
[  238.047280] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.047285] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.047302] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.047306] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.047311] dwc2 c90c0000.usb: DMA enabled
[  238.047314] dwc2 c90c0000.usb: desc DMA disabled
[  238.047318] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.047322] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[  238.047326] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.047331] dwc2 c90c0000.usb: set HCCHAR(1) to 00c80a00
[  238.047334] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[  238.047338] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.047341] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.047345] dwc2 c90c0000.usb: 	 Is In: 0
[  238.047348] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.047352] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.047355] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.047359] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.047363] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.047367] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.047371] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.047375] dwc2 c90c0000.usb: no split
[  238.047380] dwc2 c90c0000.usb: Wrote 0008001f to HCTSIZ(1)
[  238.047383] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[  238.047387] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.047390] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.047394] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.047398] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(1)
[  238.047402] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.047406] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(1)
[  238.047415] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.047419] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.047422] dwc2 c90c0000.usb: HAINT=00000002
[  238.047426] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[  238.047431] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.047435] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[  238.047439] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[  238.047443] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[  238.047447] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.047452] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.047456] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 1
[  238.047460] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.047463] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.047467] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.047470] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.047474] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.047481] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.047486] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.047491] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 2
[  238.047496] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.047500] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.047503] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.047508] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.047512] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.047557] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.047564] dwc2 c90c0000.usb: urb_enqueue, urb c60a6a1a
[  238.047568] dwc2 c90c0000.usb:   Device address: 3
[  238.047572] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.047576] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.047579] dwc2 c90c0000.usb:   Speed: HIGH
[  238.047583] dwc2 c90c0000.usb:   Max packet size: 512
[  238.047587] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.047591] dwc2 c90c0000.usb:   Transfer buffer: 89d9629a, Transfer DMA: 1fe35000
[  238.047596] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.047599] dwc2 c90c0000.usb:   Interval: 0
[  238.047605] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.047611] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.047618] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.047629] dwc2 c90c0000.usb: urb_enqueue, urb d40f5527
[  238.047633] dwc2 c90c0000.usb:   Device address: 3
[  238.047637] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.047640] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.047644] dwc2 c90c0000.usb:   Speed: HIGH
[  238.047647] dwc2 c90c0000.usb:   Max packet size: 512
[  238.047651] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.047655] dwc2 c90c0000.usb:   Transfer buffer: c2e6eba3, Transfer DMA: 2d29d000
[  238.047659] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.047663] dwc2 c90c0000.usb:   Interval: 0
[  238.047672] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.047676] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.047680] dwc2 c90c0000.usb: DMA enabled
[  238.047683] dwc2 c90c0000.usb: desc DMA disabled
[  238.047687] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.047691] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[  238.047694] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.047699] dwc2 c90c0000.usb: set HCCHAR(2) to 00c89200
[  238.047703] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[  238.047706] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.047709] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.047713] dwc2 c90c0000.usb: 	 Is In: 1
[  238.047716] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.047720] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.047723] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.047727] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.047731] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.047735] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.047739] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.047742] dwc2 c90c0000.usb: no split
[  238.047746] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(2)
[  238.047750] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[  238.047754] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.047757] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.047761] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.047765] dwc2 c90c0000.usb: Wrote 1fe35000 to HCDMA(2)
[  238.047768] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.047772] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(2)
[  238.047781] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.047785] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.047798] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.047803] dwc2 c90c0000.usb: urb_enqueue, urb 219a56a4
[  238.047807] dwc2 c90c0000.usb:   Device address: 3
[  238.047810] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.047814] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.047817] dwc2 c90c0000.usb:   Speed: HIGH
[  238.047821] dwc2 c90c0000.usb:   Max packet size: 512
[  238.047825] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.047829] dwc2 c90c0000.usb:   Transfer buffer: eeb56566, Transfer DMA: 1f822000
[  238.047834] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.047837] dwc2 c90c0000.usb:   Interval: 0
[  238.047842] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.047847] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.047854] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.047858] dwc2 c90c0000.usb: urb_enqueue, urb c4da2cad
[  238.047862] dwc2 c90c0000.usb:   Device address: 3
[  238.047866] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.047873] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.047877] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.047880] dwc2 c90c0000.usb: HAINT=00000004
[  238.047884] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[  238.047889] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.047893] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[  238.047897] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[  238.047901] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[  238.047905] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.047909] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.047914] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 2
[  238.047917] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.047921] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.047924] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.047928] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.047932] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.047938] dwc2 c90c0000.usb: dwc2_host_complete: urb c60a6a1a device 3 ep 2-IN status 0 actual 4096
[  238.047943] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.047947] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.047950] dwc2 c90c0000.usb: DMA enabled
[  238.047954] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 2
[  238.047960] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.047963] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.047967] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.047970] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.047976] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.047980] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.047983] dwc2 c90c0000.usb: DMA enabled
[  238.047986] dwc2 c90c0000.usb: desc DMA disabled
[  238.047990] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.047993] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[  238.047997] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.048002] dwc2 c90c0000.usb: set HCCHAR(3) to 00c89200
[  238.048005] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[  238.048009] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.048012] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.048016] dwc2 c90c0000.usb: 	 Is In: 1
[  238.048019] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.048022] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.048026] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.048030] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.048033] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.048037] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.048041] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.048044] dwc2 c90c0000.usb: no split
[  238.048049] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(3)
[  238.048052] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[  238.048056] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.048060] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.048063] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.048067] dwc2 c90c0000.usb: Wrote 2d29d000 to HCDMA(3)
[  238.048071] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.048075] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(3)
[  238.048079] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.048083] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.048099] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.048104] dwc2 c90c0000.usb:   Speed: HIGH
[  238.048107] dwc2 c90c0000.usb:   Max packet size: 512
[  238.048111] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.048116] dwc2 c90c0000.usb:   Transfer buffer: e733d619, Transfer DMA: 1f89c000
[  238.048120] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.048124] dwc2 c90c0000.usb:   Interval: 0
[  238.048129] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.048134] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.048141] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.048146] dwc2 c90c0000.usb: urb_enqueue, urb 1aa603dd
[  238.048150] dwc2 c90c0000.usb:   Device address: 3
[  238.048153] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.048157] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.048160] dwc2 c90c0000.usb:   Speed: HIGH
[  238.048164] dwc2 c90c0000.usb:   Max packet size: 512
[  238.048172] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.048177] dwc2 c90c0000.usb:   Transfer buffer: 0edb9681, Transfer DMA: 1fc95000
[  238.048183] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.048186] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.048190] dwc2 c90c0000.usb: HAINT=00000008
[  238.048194] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[  238.048198] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.048202] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[  238.048206] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[  238.048210] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[  238.048214] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.048218] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.048223] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 3
[  238.048226] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.048230] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.048233] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.048237] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.048241] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.048247] dwc2 c90c0000.usb: dwc2_host_complete: urb d40f5527 device 3 ep 2-IN status 0 actual 4096
[  238.048252] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.048255] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.048258] dwc2 c90c0000.usb: DMA enabled
[  238.048263] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 2
[  238.048268] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.048272] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.048275] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.048278] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.048284] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.048287] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.048291] dwc2 c90c0000.usb: DMA enabled
[  238.048294] dwc2 c90c0000.usb: desc DMA disabled
[  238.048298] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.048301] dwc2 c90c0000.usb: set HAINTMSK to 00000010
[  238.048305] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.048310] dwc2 c90c0000.usb: set HCCHAR(4) to 00c89200
[  238.048313] dwc2 c90c0000.usb: dwc2_hc_init: Channel 4
[  238.048317] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.048320] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.048324] dwc2 c90c0000.usb: 	 Is In: 1
[  238.048327] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.048331] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.048334] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.048338] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.048342] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.048345] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.048349] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.048353] dwc2 c90c0000.usb: no split
[  238.048357] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(4)
[  238.048361] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 4
[  238.048364] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.048368] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.048371] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.048376] dwc2 c90c0000.usb: Wrote 1f822000 to HCDMA(4)
[  238.048379] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.048383] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(4)
[  238.048388] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.048392] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.048409] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.048413] dwc2 c90c0000.usb:   Interval: 0
[  238.048422] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.048427] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.048441] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.048446] dwc2 c90c0000.usb: urb_enqueue, urb 9f0be01d
[  238.048449] dwc2 c90c0000.usb:   Device address: 3
[  238.048453] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.048457] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.048460] dwc2 c90c0000.usb:   Speed: HIGH
[  238.048464] dwc2 c90c0000.usb:   Max packet size: 512
[  238.048468] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.048472] dwc2 c90c0000.usb:   Transfer buffer: 1d98386b, Transfer DMA: 2d0ec000
[  238.048476] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.048482] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.048486] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.048489] dwc2 c90c0000.usb: HAINT=00000010
[  238.048493] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 4
[  238.048498] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.048502] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Channel Halted--
[  238.048506] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: DMA Channel Halted--
[  238.048510] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Transfer Complete--
[  238.048513] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.048518] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.048522] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 4
[  238.048526] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.048529] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.048533] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.048536] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.048540] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.048546] dwc2 c90c0000.usb: dwc2_host_complete: urb 219a56a4 device 3 ep 2-IN status 0 actual 4096
[  238.048551] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.048554] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.048557] dwc2 c90c0000.usb: DMA enabled
[  238.048562] dwc2 c90c0000.usb:   dwc2_release_channel: channel 4, halt_status 2
[  238.048567] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.048571] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.048574] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.048577] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.048583] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.048587] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.048590] dwc2 c90c0000.usb: DMA enabled
[  238.048593] dwc2 c90c0000.usb: desc DMA disabled
[  238.048597] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.048601] dwc2 c90c0000.usb: set HAINTMSK to 00000040
[  238.048605] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.048609] dwc2 c90c0000.usb: set HCCHAR(6) to 00c89200
[  238.048613] dwc2 c90c0000.usb: dwc2_hc_init: Channel 6
[  238.048616] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.048620] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.048623] dwc2 c90c0000.usb: 	 Is In: 1
[  238.048626] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.048630] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.048633] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.048637] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.048641] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.048644] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.048648] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.048652] dwc2 c90c0000.usb: no split
[  238.048656] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(6)
[  238.048660] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 6
[  238.048664] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.048667] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.048671] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.048675] dwc2 c90c0000.usb: Wrote 1f89c000 to HCDMA(6)
[  238.048679] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.048683] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(6)
[  238.048687] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.048691] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.048705] dwc2 c90c0000.usb:   Interval: 0
[  238.048712] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.048717] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.048726] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.048730] dwc2 c90c0000.usb: urb_enqueue, urb b9fdbbfd
[  238.048734] dwc2 c90c0000.usb:   Device address: 3
[  238.048737] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.048741] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.048745] dwc2 c90c0000.usb:   Speed: HIGH
[  238.048748] dwc2 c90c0000.usb:   Max packet size: 512
[  238.048752] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.048756] dwc2 c90c0000.usb:   Transfer buffer: 13b27b8f, Transfer DMA: 2d327000
[  238.048761] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.048764] dwc2 c90c0000.usb:   Interval: 0
[  238.048770] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.048774] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.048783] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.048786] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.048790] dwc2 c90c0000.usb: HAINT=00000040
[  238.048794] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 6
[  238.048798] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.048802] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Channel Halted--
[  238.048806] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: DMA Channel Halted--
[  238.048811] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Transfer Complete--
[  238.048814] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.048818] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.048823] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 6
[  238.048826] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.048830] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.048833] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.048837] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.048841] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.048846] dwc2 c90c0000.usb: dwc2_host_complete: urb c4da2cad device 3 ep 2-IN status 0 actual 4096
[  238.048851] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.048855] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.048858] dwc2 c90c0000.usb: DMA enabled
[  238.048862] dwc2 c90c0000.usb:   dwc2_release_channel: channel 6, halt_status 2
[  238.048868] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.048871] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.048875] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.048878] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.048883] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.048887] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.048890] dwc2 c90c0000.usb: DMA enabled
[  238.048894] dwc2 c90c0000.usb: desc DMA disabled
[  238.048898] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.048902] dwc2 c90c0000.usb: set HAINTMSK to 00000020
[  238.048905] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.048910] dwc2 c90c0000.usb: set HCCHAR(5) to 00c89200
[  238.048913] dwc2 c90c0000.usb: dwc2_hc_init: Channel 5
[  238.048917] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.048920] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.048923] dwc2 c90c0000.usb: 	 Is In: 1
[  238.048927] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.048930] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.048934] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.048938] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.048941] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.048945] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.048949] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.048952] dwc2 c90c0000.usb: no split
[  238.048956] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(5)
[  238.048960] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 5
[  238.048964] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.048967] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.048971] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.048975] dwc2 c90c0000.usb: Wrote 1fc95000 to HCDMA(5)
[  238.048979] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.048983] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(5)
[  238.048987] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.048991] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.049085] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.049090] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.049094] dwc2 c90c0000.usb: HAINT=00000020
[  238.049098] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 5
[  238.049102] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.049106] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Channel Halted--
[  238.049110] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: DMA Channel Halted--
[  238.049114] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Transfer Complete--
[  238.049118] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.049122] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.049127] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 5
[  238.049130] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.049134] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.049137] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.049141] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.049145] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.049151] dwc2 c90c0000.usb: dwc2_host_complete: urb 1aa603dd device 3 ep 2-IN status 0 actual 4096
[  238.049156] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.049160] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.049163] dwc2 c90c0000.usb: DMA enabled
[  238.049167] dwc2 c90c0000.usb:   dwc2_release_channel: channel 5, halt_status 2
[  238.049172] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.049176] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.049180] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.049183] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.049188] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.049192] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.049195] dwc2 c90c0000.usb: DMA enabled
[  238.049199] dwc2 c90c0000.usb: desc DMA disabled
[  238.049203] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.049207] dwc2 c90c0000.usb: set HAINTMSK to 00000080
[  238.049215] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.049219] dwc2 c90c0000.usb: set HCCHAR(7) to 00c89200
[  238.049223] dwc2 c90c0000.usb: dwc2_hc_init: Channel 7
[  238.049226] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.049230] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.049233] dwc2 c90c0000.usb: 	 Is In: 1
[  238.049237] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.049240] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.049244] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.049248] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.049252] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.049255] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.049259] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.049263] dwc2 c90c0000.usb: no split
[  238.049267] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(7)
[  238.049271] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 7
[  238.049274] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.049278] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.049281] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.049286] dwc2 c90c0000.usb: Wrote 2d0ec000 to HCDMA(7)
[  238.049289] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.049293] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(7)
[  238.049298] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.049302] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.049395] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.049399] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.049403] dwc2 c90c0000.usb: HAINT=00000080
[  238.049407] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 7
[  238.049411] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.049415] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Channel Halted--
[  238.049419] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: DMA Channel Halted--
[  238.049423] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Transfer Complete--
[  238.049427] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.049431] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.049435] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 7
[  238.049439] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.049442] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.049446] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.049450] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.049454] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.049460] dwc2 c90c0000.usb: dwc2_host_complete: urb 9f0be01d device 3 ep 2-IN status 0 actual 4096
[  238.049465] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.049468] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.049471] dwc2 c90c0000.usb: DMA enabled
[  238.049476] dwc2 c90c0000.usb:   dwc2_release_channel: channel 7, halt_status 2
[  238.049481] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.049484] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.049488] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.049491] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.049496] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.049500] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.049503] dwc2 c90c0000.usb: DMA enabled
[  238.049507] dwc2 c90c0000.usb: desc DMA disabled
[  238.049510] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.049514] dwc2 c90c0000.usb: set HAINTMSK to 00000100
[  238.049518] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.049522] dwc2 c90c0000.usb: set HCCHAR(8) to 00c89200
[  238.049526] dwc2 c90c0000.usb: dwc2_hc_init: Channel 8
[  238.049529] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.049533] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.049536] dwc2 c90c0000.usb: 	 Is In: 1
[  238.049539] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.049543] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.049546] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.049550] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.049554] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.049558] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.049561] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.049565] dwc2 c90c0000.usb: no split
[  238.049569] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(8)
[  238.049573] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 8
[  238.049576] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.049580] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.049583] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.049587] dwc2 c90c0000.usb: Wrote 2d327000 to HCDMA(8)
[  238.049591] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.049595] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(8)
[  238.049599] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.049603] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.049696] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.049700] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.049704] dwc2 c90c0000.usb: HAINT=00000100
[  238.049708] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 8
[  238.049713] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.049717] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Channel Halted--
[  238.049721] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: DMA Channel Halted--
[  238.049725] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Transfer Complete--
[  238.049728] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.049733] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.049737] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 8
[  238.049740] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.049744] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.049747] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.049751] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.049755] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.049761] dwc2 c90c0000.usb: dwc2_host_complete: urb b9fdbbfd device 3 ep 2-IN status 0 actual 4096
[  238.049766] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.049769] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.049773] dwc2 c90c0000.usb: DMA enabled
[  238.049777] dwc2 c90c0000.usb:   dwc2_release_channel: channel 8, halt_status 2
[  238.049782] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.049786] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.049789] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.049793] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.049798] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.049833] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.049839] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.049842] dwc2 c90c0000.usb:   Device address: 3
[  238.049847] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.049851] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.049854] dwc2 c90c0000.usb:   Speed: HIGH
[  238.049858] dwc2 c90c0000.usb:   Max packet size: 512
[  238.049862] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.049866] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.049871] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.049874] dwc2 c90c0000.usb:   Interval: 0
[  238.049881] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.049886] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.049924] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.049929] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.049932] dwc2 c90c0000.usb: DMA enabled
[  238.049935] dwc2 c90c0000.usb: desc DMA disabled
[  238.049939] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.049943] dwc2 c90c0000.usb: set HAINTMSK to 00000200
[  238.049947] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.049951] dwc2 c90c0000.usb: set HCCHAR(9) to 00c89200
[  238.049955] dwc2 c90c0000.usb: dwc2_hc_init: Channel 9
[  238.049958] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.049961] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.049965] dwc2 c90c0000.usb: 	 Is In: 1
[  238.049974] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.049977] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.049981] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.049985] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.049989] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.049992] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.049996] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.050000] dwc2 c90c0000.usb: no split
[  238.050004] dwc2 c90c0000.usb: Wrote 00080200 to HCTSIZ(9)
[  238.050008] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 9
[  238.050011] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.050015] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.050018] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.050023] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(9)
[  238.050026] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.050030] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(9)
[  238.050050] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.050054] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.050058] dwc2 c90c0000.usb: HAINT=00000200
[  238.050062] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 9
[  238.050067] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.050071] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Channel Halted--
[  238.050075] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: DMA Channel Halted--
[  238.050079] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Transfer Complete--
[  238.050083] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.050087] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.050091] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 9
[  238.050095] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.050099] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.050102] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.050106] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.050110] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.050116] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.050121] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.050125] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.050128] dwc2 c90c0000.usb: DMA enabled
[  238.050132] dwc2 c90c0000.usb:   dwc2_release_channel: channel 9, halt_status 2
[  238.050138] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.050141] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.050145] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.050149] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.050154] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.050263] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.050270] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.050274] dwc2 c90c0000.usb:   Device address: 3
[  238.050278] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.050281] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.050285] dwc2 c90c0000.usb:   Speed: HIGH
[  238.050289] dwc2 c90c0000.usb:   Max packet size: 512
[  238.050299] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.050303] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.050308] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.050311] dwc2 c90c0000.usb:   Interval: 0
[  238.050318] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.050324] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.050424] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.050429] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.050432] dwc2 c90c0000.usb: DMA enabled
[  238.050435] dwc2 c90c0000.usb: desc DMA disabled
[  238.050439] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.050443] dwc2 c90c0000.usb: set HAINTMSK to 00000400
[  238.050447] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.050451] dwc2 c90c0000.usb: set HCCHAR(10) to 00c80a00
[  238.050455] dwc2 c90c0000.usb: dwc2_hc_init: Channel 10
[  238.050458] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.050462] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.050465] dwc2 c90c0000.usb: 	 Is In: 0
[  238.050469] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.050472] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.050476] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.050480] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.050483] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.050487] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.050491] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.050495] dwc2 c90c0000.usb: no split
[  238.050499] dwc2 c90c0000.usb: Wrote 4008001f to HCTSIZ(10)
[  238.050503] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 10
[  238.050507] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.050510] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.050514] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.050518] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(10)
[  238.050522] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.050526] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(10)
[  238.050536] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.050540] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.050544] dwc2 c90c0000.usb: HAINT=00000400
[  238.050548] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 10
[  238.050553] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.050557] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Channel Halted--
[  238.050561] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: DMA Channel Halted--
[  238.050565] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Transfer Complete--
[  238.050569] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.050573] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.050578] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 10
[  238.050581] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.050585] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.050589] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.050592] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.050596] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.050602] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.050608] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.050613] dwc2 c90c0000.usb:   dwc2_release_channel: channel 10, halt_status 2
[  238.050618] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.050622] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.050625] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.050630] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.050634] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.050684] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.050690] dwc2 c90c0000.usb: urb_enqueue, urb d40f5527
[  238.050693] dwc2 c90c0000.usb:   Device address: 3
[  238.050697] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.050701] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.050705] dwc2 c90c0000.usb:   Speed: HIGH
[  238.050709] dwc2 c90c0000.usb:   Max packet size: 512
[  238.050712] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.050717] dwc2 c90c0000.usb:   Transfer buffer: f98de342, Transfer DMA: 2d323000
[  238.050722] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.050726] dwc2 c90c0000.usb:   Interval: 0
[  238.050732] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.050737] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.050745] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.050750] dwc2 c90c0000.usb: urb_enqueue, urb 219a56a4
[  238.050753] dwc2 c90c0000.usb:   Device address: 3
[  238.050757] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.050761] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.050764] dwc2 c90c0000.usb:   Speed: HIGH
[  238.050768] dwc2 c90c0000.usb:   Max packet size: 512
[  238.050772] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.050776] dwc2 c90c0000.usb:   Transfer buffer: 6b2601e9, Transfer DMA: 1fbf8000
[  238.050780] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.050784] dwc2 c90c0000.usb:   Interval: 0
[  238.050789] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.050797] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.050801] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.050810] dwc2 c90c0000.usb: DMA enabled
[  238.050813] dwc2 c90c0000.usb: desc DMA disabled
[  238.050817] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.050821] dwc2 c90c0000.usb: set HAINTMSK to 00000800
[  238.050825] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.050829] dwc2 c90c0000.usb: set HCCHAR(11) to 00c89200
[  238.050833] dwc2 c90c0000.usb: dwc2_hc_init: Channel 11
[  238.050836] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.050840] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.050843] dwc2 c90c0000.usb: 	 Is In: 1
[  238.050846] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.050850] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.050853] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.050857] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.050861] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.050865] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.050869] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.050872] dwc2 c90c0000.usb: no split
[  238.050876] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(11)
[  238.050880] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 11
[  238.050884] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.050887] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.050891] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.050895] dwc2 c90c0000.usb: Wrote 2d323000 to HCDMA(11)
[  238.050899] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.050903] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(11)
[  238.050910] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.050922] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.050926] dwc2 c90c0000.usb: urb_enqueue, urb c4da2cad
[  238.050930] dwc2 c90c0000.usb:   Device address: 3
[  238.050934] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.050938] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.050941] dwc2 c90c0000.usb:   Speed: HIGH
[  238.050944] dwc2 c90c0000.usb:   Max packet size: 512
[  238.050948] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.050953] dwc2 c90c0000.usb:   Transfer buffer: b1b18f68, Transfer DMA: 1ffd0000
[  238.050957] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.050960] dwc2 c90c0000.usb:   Interval: 0
[  238.050966] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.050970] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.050977] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.050982] dwc2 c90c0000.usb: urb_enqueue, urb 1aa603dd
[  238.050985] dwc2 c90c0000.usb:   Device address: 3
[  238.050989] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.050993] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.050996] dwc2 c90c0000.usb:   Speed: HIGH
[  238.051000] dwc2 c90c0000.usb:   Max packet size: 512
[  238.051003] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.051008] dwc2 c90c0000.usb:   Transfer buffer: 5afac01e, Transfer DMA: 2d328000
[  238.051012] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.051018] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.051022] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.051025] dwc2 c90c0000.usb: HAINT=00000800
[  238.051029] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 11
[  238.051034] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.051038] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Channel Halted--
[  238.051042] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: DMA Channel Halted--
[  238.051047] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Transfer Complete--
[  238.051050] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.051055] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.051059] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 11
[  238.051063] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.051066] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.051070] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.051073] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.051077] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.051084] dwc2 c90c0000.usb: dwc2_host_complete: urb d40f5527 device 3 ep 2-IN status 0 actual 4096
[  238.051089] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.051093] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.051096] dwc2 c90c0000.usb: DMA enabled
[  238.051101] dwc2 c90c0000.usb:   dwc2_release_channel: channel 11, halt_status 2
[  238.051106] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.051110] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.051113] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.051116] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.051122] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.051126] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.051129] dwc2 c90c0000.usb: DMA enabled
[  238.051132] dwc2 c90c0000.usb: desc DMA disabled
[  238.051136] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.051140] dwc2 c90c0000.usb: set HAINTMSK to 00001000
[  238.051143] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.051148] dwc2 c90c0000.usb: set HCCHAR(12) to 00c89200
[  238.051152] dwc2 c90c0000.usb: dwc2_hc_init: Channel 12
[  238.051155] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.051159] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.051162] dwc2 c90c0000.usb: 	 Is In: 1
[  238.051166] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.051169] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.051173] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.051176] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.051180] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.051184] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.051188] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.051191] dwc2 c90c0000.usb: no split
[  238.051196] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(12)
[  238.051200] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 12
[  238.051203] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.051207] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.051210] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.051214] dwc2 c90c0000.usb: Wrote 1fbf8000 to HCDMA(12)
[  238.051218] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.051222] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(12)
[  238.051226] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.051231] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.051249] dwc2 c90c0000.usb:   Interval: 0
[  238.051255] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.051260] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.051268] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.051273] dwc2 c90c0000.usb: urb_enqueue, urb 9f0be01d
[  238.051277] dwc2 c90c0000.usb:   Device address: 3
[  238.051281] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.051284] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.051288] dwc2 c90c0000.usb:   Speed: HIGH
[  238.051296] dwc2 c90c0000.usb:   Max packet size: 512
[  238.051300] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.051304] dwc2 c90c0000.usb:   Transfer buffer: e07e4f59, Transfer DMA: 1f812000
[  238.051309] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.051312] dwc2 c90c0000.usb:   Interval: 0
[  238.051317] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.051323] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.051327] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.051331] dwc2 c90c0000.usb: HAINT=00001000
[  238.051335] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 12
[  238.051339] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.051343] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Channel Halted--
[  238.051347] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: DMA Channel Halted--
[  238.051351] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Transfer Complete--
[  238.051354] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.051359] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.051363] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 12
[  238.051367] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.051370] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.051374] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.051378] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.051382] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.051387] dwc2 c90c0000.usb: dwc2_host_complete: urb 219a56a4 device 3 ep 2-IN status 0 actual 4096
[  238.051392] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.051396] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.051399] dwc2 c90c0000.usb: DMA enabled
[  238.051403] dwc2 c90c0000.usb:   dwc2_release_channel: channel 12, halt_status 2
[  238.051408] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.051412] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.051415] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.051419] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.051424] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.051428] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.051431] dwc2 c90c0000.usb: DMA enabled
[  238.051434] dwc2 c90c0000.usb: desc DMA disabled
[  238.051438] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.051442] dwc2 c90c0000.usb: set HAINTMSK to 00002000
[  238.051446] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.051450] dwc2 c90c0000.usb: set HCCHAR(13) to 00c89200
[  238.051454] dwc2 c90c0000.usb: dwc2_hc_init: Channel 13
[  238.051457] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.051461] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.051464] dwc2 c90c0000.usb: 	 Is In: 1
[  238.051468] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.051471] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.051475] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.051478] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.051482] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.051486] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.051489] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.051493] dwc2 c90c0000.usb: no split
[  238.051497] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(13)
[  238.051501] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 13
[  238.051505] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.051508] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.051512] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.051516] dwc2 c90c0000.usb: Wrote 1ffd0000 to HCDMA(13)
[  238.051520] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.051524] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(13)
[  238.051528] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.051532] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.051552] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.051560] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.051565] dwc2 c90c0000.usb: urb_enqueue, urb b9fdbbfd
[  238.051569] dwc2 c90c0000.usb:   Device address: 3
[  238.051573] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.051577] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.051580] dwc2 c90c0000.usb:   Speed: HIGH
[  238.051585] dwc2 c90c0000.usb:   Max packet size: 512
[  238.051588] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.051593] dwc2 c90c0000.usb:   Transfer buffer: ca3da4e2, Transfer DMA: 1fba3000
[  238.051597] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.051600] dwc2 c90c0000.usb:   Interval: 0
[  238.051606] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.051616] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.051624] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.051628] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.051631] dwc2 c90c0000.usb: HAINT=00002000
[  238.051635] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 13
[  238.051640] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.051644] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Channel Halted--
[  238.051647] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: DMA Channel Halted--
[  238.051652] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Transfer Complete--
[  238.051655] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.051659] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.051664] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 13
[  238.051667] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.051671] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.051674] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.051678] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.051682] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.051688] dwc2 c90c0000.usb: dwc2_host_complete: urb c4da2cad device 3 ep 2-IN status 0 actual 4096
[  238.051693] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.051696] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.051700] dwc2 c90c0000.usb: DMA enabled
[  238.051704] dwc2 c90c0000.usb:   dwc2_release_channel: channel 13, halt_status 2
[  238.051710] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.051713] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.051717] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.051720] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.051726] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.051729] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.051733] dwc2 c90c0000.usb: DMA enabled
[  238.051736] dwc2 c90c0000.usb: desc DMA disabled
[  238.051740] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.051744] dwc2 c90c0000.usb: set HAINTMSK to 00004000
[  238.051748] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.051752] dwc2 c90c0000.usb: set HCCHAR(14) to 00c89200
[  238.051755] dwc2 c90c0000.usb: dwc2_hc_init: Channel 14
[  238.051759] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.051762] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.051766] dwc2 c90c0000.usb: 	 Is In: 1
[  238.051770] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.051773] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.051777] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.051780] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.051784] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.051788] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.051792] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.051796] dwc2 c90c0000.usb: no split
[  238.051800] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(14)
[  238.051804] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 14
[  238.051808] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.051811] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.051815] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.051819] dwc2 c90c0000.usb: Wrote 2d328000 to HCDMA(14)
[  238.051823] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.051827] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(14)
[  238.051831] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.051836] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.051858] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.051863] dwc2 c90c0000.usb: urb_enqueue, urb 22feec5c
[  238.051867] dwc2 c90c0000.usb:   Device address: 3
[  238.051871] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.051875] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.051878] dwc2 c90c0000.usb:   Speed: HIGH
[  238.051882] dwc2 c90c0000.usb:   Max packet size: 512
[  238.051886] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.051890] dwc2 c90c0000.usb:   Transfer buffer: 0b957638, Transfer DMA: 1fc29000
[  238.051895] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.051898] dwc2 c90c0000.usb:   Interval: 0
[  238.051904] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.051909] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.051921] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.051926] dwc2 c90c0000.usb: urb_enqueue, urb 5b2f2d21
[  238.051933] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.051936] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.051940] dwc2 c90c0000.usb: HAINT=00004000
[  238.051944] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 14
[  238.051949] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.051952] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Channel Halted--
[  238.051956] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: DMA Channel Halted--
[  238.051960] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Transfer Complete--
[  238.051964] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.051968] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.051972] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 14
[  238.051976] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.051979] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.051983] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.051986] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.051990] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.051996] dwc2 c90c0000.usb: dwc2_host_complete: urb 1aa603dd device 3 ep 2-IN status 0 actual 4096
[  238.052001] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.052004] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.052008] dwc2 c90c0000.usb: DMA enabled
[  238.052012] dwc2 c90c0000.usb:   dwc2_release_channel: channel 14, halt_status 2
[  238.052017] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.052021] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.052024] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.052028] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.052033] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.052037] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.052040] dwc2 c90c0000.usb: DMA enabled
[  238.052043] dwc2 c90c0000.usb: desc DMA disabled
[  238.052047] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.052051] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[  238.052055] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.052059] dwc2 c90c0000.usb: set HCCHAR(0) to 00c89200
[  238.052062] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[  238.052066] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.052069] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.052073] dwc2 c90c0000.usb: 	 Is In: 1
[  238.052076] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.052079] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.052084] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.052087] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.052091] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.052095] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.052099] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.052102] dwc2 c90c0000.usb: no split
[  238.052107] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(0)
[  238.052110] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[  238.052114] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.052117] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.052121] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.052125] dwc2 c90c0000.usb: Wrote 1f812000 to HCDMA(0)
[  238.052129] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.052133] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(0)
[  238.052137] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.052142] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.052156] dwc2 c90c0000.usb:   Device address: 3
[  238.052160] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.052164] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.052171] dwc2 c90c0000.usb:   Speed: HIGH
[  238.052175] dwc2 c90c0000.usb:   Max packet size: 512
[  238.052179] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.052183] dwc2 c90c0000.usb:   Transfer buffer: ce5fa863, Transfer DMA: 2e7a9000
[  238.052188] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.052191] dwc2 c90c0000.usb:   Interval: 0
[  238.052197] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.052202] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.052211] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.052215] dwc2 c90c0000.usb: urb_enqueue, urb 64d8cdc0
[  238.052219] dwc2 c90c0000.usb:   Device address: 3
[  238.052223] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.052227] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.052233] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.052236] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.052240] dwc2 c90c0000.usb: HAINT=00000001
[  238.052244] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[  238.052249] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.052252] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Channel Halted--
[  238.052256] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: DMA Channel Halted--
[  238.052260] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Transfer Complete--
[  238.052264] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.052268] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.052273] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 0
[  238.052276] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.052279] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.052283] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.052287] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.052291] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.052296] dwc2 c90c0000.usb: dwc2_host_complete: urb 9f0be01d device 3 ep 2-IN status 0 actual 4096
[  238.052302] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.052305] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.052309] dwc2 c90c0000.usb: DMA enabled
[  238.052313] dwc2 c90c0000.usb:   dwc2_release_channel: channel 0, halt_status 2
[  238.052318] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.052322] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.052325] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.052329] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.052334] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.052338] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.052341] dwc2 c90c0000.usb: DMA enabled
[  238.052344] dwc2 c90c0000.usb: desc DMA disabled
[  238.052348] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.052353] dwc2 c90c0000.usb: set HAINTMSK to 00008000
[  238.052357] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.052361] dwc2 c90c0000.usb: set HCCHAR(15) to 00c89200
[  238.052364] dwc2 c90c0000.usb: dwc2_hc_init: Channel 15
[  238.052368] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.052371] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.052375] dwc2 c90c0000.usb: 	 Is In: 1
[  238.052378] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.052382] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.052385] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.052389] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.052393] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.052396] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.052400] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.052403] dwc2 c90c0000.usb: no split
[  238.052408] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(15)
[  238.052412] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 15
[  238.052415] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.052419] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.052422] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.052427] dwc2 c90c0000.usb: Wrote 1fba3000 to HCDMA(15)
[  238.052430] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.052434] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(15)
[  238.052439] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.052443] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.052462] dwc2 c90c0000.usb:   Speed: HIGH
[  238.052466] dwc2 c90c0000.usb:   Max packet size: 512
[  238.052470] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.052475] dwc2 c90c0000.usb:   Transfer buffer: 895e69fa, Transfer DMA: 1fc00000
[  238.052479] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.052482] dwc2 c90c0000.usb:   Interval: 0
[  238.052495] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.052500] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.052510] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.052515] dwc2 c90c0000.usb: urb_enqueue, urb 544633e2
[  238.052518] dwc2 c90c0000.usb:   Device address: 3
[  238.052522] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.052526] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.052529] dwc2 c90c0000.usb:   Speed: HIGH
[  238.052536] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.052540] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.052543] dwc2 c90c0000.usb: HAINT=00008000
[  238.052547] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 15
[  238.052552] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.052556] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Channel Halted--
[  238.052560] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: DMA Channel Halted--
[  238.052565] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Transfer Complete--
[  238.052568] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.052572] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.052577] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 15
[  238.052580] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.052584] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.052587] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.052591] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.052595] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.052601] dwc2 c90c0000.usb: dwc2_host_complete: urb b9fdbbfd device 3 ep 2-IN status 0 actual 4096
[  238.052605] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.052609] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.052612] dwc2 c90c0000.usb: DMA enabled
[  238.052616] dwc2 c90c0000.usb:   dwc2_release_channel: channel 15, halt_status 2
[  238.052622] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.052625] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.052629] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.052632] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.052637] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.052641] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.052644] dwc2 c90c0000.usb: DMA enabled
[  238.052648] dwc2 c90c0000.usb: desc DMA disabled
[  238.052651] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.052655] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[  238.052659] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.052663] dwc2 c90c0000.usb: set HCCHAR(1) to 00c89200
[  238.052667] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[  238.052670] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.052674] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.052677] dwc2 c90c0000.usb: 	 Is In: 1
[  238.052680] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.052684] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.052687] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.052691] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.052695] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.052699] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.052702] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.052706] dwc2 c90c0000.usb: no split
[  238.052710] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(1)
[  238.052714] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[  238.052718] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.052721] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.052724] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.052729] dwc2 c90c0000.usb: Wrote 1fc29000 to HCDMA(1)
[  238.052732] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.052737] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(1)
[  238.052741] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.052745] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.052762] dwc2 c90c0000.usb:   Max packet size: 512
[  238.052766] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.052770] dwc2 c90c0000.usb:   Transfer buffer: b97fb32e, Transfer DMA: 1fab8000
[  238.052775] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.052778] dwc2 c90c0000.usb:   Interval: 0
[  238.052783] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.052788] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.052800] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.052805] dwc2 c90c0000.usb: urb_enqueue, urb cd91f79f
[  238.052809] dwc2 c90c0000.usb:   Device address: 3
[  238.052812] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.052816] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.052819] dwc2 c90c0000.usb:   Speed: HIGH
[  238.052823] dwc2 c90c0000.usb:   Max packet size: 512
[  238.052827] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.052831] dwc2 c90c0000.usb:   Transfer buffer: 0f6583eb, Transfer DMA: 1fcab000
[  238.052837] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.052841] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.052844] dwc2 c90c0000.usb: HAINT=00000002
[  238.052848] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[  238.052853] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.052857] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[  238.052861] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[  238.052865] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[  238.052868] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.052872] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.052877] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 1
[  238.052880] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.052884] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.052887] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.052891] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.052895] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.052901] dwc2 c90c0000.usb: dwc2_host_complete: urb 22feec5c device 3 ep 2-IN status 0 actual 4096
[  238.052905] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.052909] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.052912] dwc2 c90c0000.usb: DMA enabled
[  238.052917] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 2
[  238.052922] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.052926] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.052929] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.052932] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.052938] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.052942] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.052945] dwc2 c90c0000.usb: DMA enabled
[  238.052948] dwc2 c90c0000.usb: desc DMA disabled
[  238.052952] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.052955] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[  238.052959] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.052963] dwc2 c90c0000.usb: set HCCHAR(2) to 00c89200
[  238.052967] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[  238.052971] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.052974] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.052977] dwc2 c90c0000.usb: 	 Is In: 1
[  238.052981] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.052984] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.052988] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.052991] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.052995] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.052999] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.053003] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.053006] dwc2 c90c0000.usb: no split
[  238.053011] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(2)
[  238.053015] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[  238.053018] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.053022] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.053025] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.053029] dwc2 c90c0000.usb: Wrote 2e7a9000 to HCDMA(2)
[  238.053033] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.053037] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(2)
[  238.053041] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.053045] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.053063] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.053066] dwc2 c90c0000.usb:   Interval: 0
[  238.053072] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.053077] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.053087] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.053092] dwc2 c90c0000.usb: urb_enqueue, urb 67466227
[  238.053095] dwc2 c90c0000.usb:   Device address: 3
[  238.053099] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.053103] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.053106] dwc2 c90c0000.usb:   Speed: HIGH
[  238.053110] dwc2 c90c0000.usb:   Max packet size: 512
[  238.053113] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.053118] dwc2 c90c0000.usb:   Transfer buffer: 5de1fa59, Transfer DMA: 2e7a6000
[  238.053122] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.053125] dwc2 c90c0000.usb:   Interval: 0
[  238.053131] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.053135] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.053142] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.053146] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.053149] dwc2 c90c0000.usb: HAINT=00000004
[  238.053153] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[  238.053158] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.053162] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[  238.053166] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[  238.053171] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[  238.053174] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.053178] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.053183] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 2
[  238.053186] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.053190] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.053194] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.053197] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.053201] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.053207] dwc2 c90c0000.usb: dwc2_host_complete: urb 5b2f2d21 device 3 ep 2-IN status 0 actual 4096
[  238.053212] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.053216] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.053219] dwc2 c90c0000.usb: DMA enabled
[  238.053223] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 2
[  238.053228] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.053232] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.053235] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.053238] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.053244] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.053248] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.053251] dwc2 c90c0000.usb: DMA enabled
[  238.053254] dwc2 c90c0000.usb: desc DMA disabled
[  238.053258] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.053262] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[  238.053266] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.053270] dwc2 c90c0000.usb: set HCCHAR(3) to 00c89200
[  238.053274] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[  238.053277] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.053280] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.053284] dwc2 c90c0000.usb: 	 Is In: 1
[  238.053292] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.053296] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.053299] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.053303] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.053307] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.053310] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.053314] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.053317] dwc2 c90c0000.usb: no split
[  238.053322] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(3)
[  238.053325] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[  238.053329] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.053332] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.053336] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.053340] dwc2 c90c0000.usb: Wrote 1fc00000 to HCDMA(3)
[  238.053344] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.053348] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(3)
[  238.053352] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.053357] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.053378] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.053383] dwc2 c90c0000.usb: urb_enqueue, urb a7ce381f
[  238.053386] dwc2 c90c0000.usb:   Device address: 3
[  238.053390] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.053394] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.053397] dwc2 c90c0000.usb:   Speed: HIGH
[  238.053401] dwc2 c90c0000.usb:   Max packet size: 512
[  238.053405] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.053409] dwc2 c90c0000.usb:   Transfer buffer: a978a10e, Transfer DMA: 2e7ab000
[  238.053414] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.053421] dwc2 c90c0000.usb:   Interval: 0
[  238.053427] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.053432] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.053440] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.053450] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.053454] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.053457] dwc2 c90c0000.usb: HAINT=00000008
[  238.053461] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[  238.053466] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.053470] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[  238.053473] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[  238.053478] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[  238.053481] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.053485] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.053490] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 3
[  238.053493] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.053497] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.053501] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.053504] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.053508] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.053514] dwc2 c90c0000.usb: dwc2_host_complete: urb 64d8cdc0 device 3 ep 2-IN status 0 actual 4096
[  238.053519] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.053522] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.053526] dwc2 c90c0000.usb: DMA enabled
[  238.053530] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 2
[  238.053535] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.053539] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.053542] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.053546] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.053551] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.053555] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.053558] dwc2 c90c0000.usb: DMA enabled
[  238.053562] dwc2 c90c0000.usb: desc DMA disabled
[  238.053565] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.053569] dwc2 c90c0000.usb: set HAINTMSK to 00000010
[  238.053573] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.053577] dwc2 c90c0000.usb: set HCCHAR(4) to 00c89200
[  238.053581] dwc2 c90c0000.usb: dwc2_hc_init: Channel 4
[  238.053585] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.053588] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.053591] dwc2 c90c0000.usb: 	 Is In: 1
[  238.053595] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.053598] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.053602] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.053606] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.053609] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.053613] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.053617] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.053620] dwc2 c90c0000.usb: no split
[  238.053625] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(4)
[  238.053628] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 4
[  238.053632] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.053635] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.053639] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.053643] dwc2 c90c0000.usb: Wrote 1fab8000 to HCDMA(4)
[  238.053647] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.053651] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(4)
[  238.053655] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.053659] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.053676] dwc2 c90c0000.usb: urb_enqueue, urb 5f70d834
[  238.053680] dwc2 c90c0000.usb:   Device address: 3
[  238.053684] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.053688] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.053691] dwc2 c90c0000.usb:   Speed: HIGH
[  238.053695] dwc2 c90c0000.usb:   Max packet size: 512
[  238.053699] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.053703] dwc2 c90c0000.usb:   Transfer buffer: 855c167b, Transfer DMA: 1fb27000
[  238.053708] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.053711] dwc2 c90c0000.usb:   Interval: 0
[  238.053717] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.053721] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.053730] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.053735] dwc2 c90c0000.usb: urb_enqueue, urb c4a7e8a9
[  238.053738] dwc2 c90c0000.usb:   Device address: 3
[  238.053742] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.053746] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.053752] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.053756] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.053759] dwc2 c90c0000.usb: HAINT=00000010
[  238.053763] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 4
[  238.053768] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.053772] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Channel Halted--
[  238.053776] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: DMA Channel Halted--
[  238.053780] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Transfer Complete--
[  238.053783] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.053788] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.053792] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 4
[  238.053796] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.053799] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.053803] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.053806] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.053810] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.053816] dwc2 c90c0000.usb: dwc2_host_complete: urb 544633e2 device 3 ep 2-IN status 0 actual 4096
[  238.053821] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.053824] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.053827] dwc2 c90c0000.usb: DMA enabled
[  238.053832] dwc2 c90c0000.usb:   dwc2_release_channel: channel 4, halt_status 2
[  238.053837] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.053841] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.053844] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.053847] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.053853] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.053856] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.053860] dwc2 c90c0000.usb: DMA enabled
[  238.053863] dwc2 c90c0000.usb: desc DMA disabled
[  238.053867] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.053870] dwc2 c90c0000.usb: set HAINTMSK to 00000040
[  238.053874] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.053878] dwc2 c90c0000.usb: set HCCHAR(6) to 00c89200
[  238.053882] dwc2 c90c0000.usb: dwc2_hc_init: Channel 6
[  238.053886] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.053889] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.053892] dwc2 c90c0000.usb: 	 Is In: 1
[  238.053896] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.053899] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.053903] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.053906] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.053910] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.053914] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.053918] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.053921] dwc2 c90c0000.usb: no split
[  238.053926] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(6)
[  238.053929] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 6
[  238.053933] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.053936] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.053940] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.053944] dwc2 c90c0000.usb: Wrote 1fcab000 to HCDMA(6)
[  238.053948] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.053952] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(6)
[  238.053957] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.053961] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.054017] dwc2 c90c0000.usb:   Speed: HIGH
[  238.054023] dwc2 c90c0000.usb:   Max packet size: 512
[  238.054026] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.054032] dwc2 c90c0000.usb:   Transfer buffer: 82392775, Transfer DMA: 1fbe2000
[  238.054036] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.054040] dwc2 c90c0000.usb:   Interval: 0
[  238.054053] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.054059] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.054063] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.054066] dwc2 c90c0000.usb: HAINT=00000040
[  238.054070] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 6
[  238.054075] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.054079] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Channel Halted--
[  238.054083] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: DMA Channel Halted--
[  238.054087] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Transfer Complete--
[  238.054091] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.054095] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.054100] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 6
[  238.054103] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.054107] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.054111] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.054114] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.054118] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.054124] dwc2 c90c0000.usb: dwc2_host_complete: urb cd91f79f device 3 ep 2-IN status 0 actual 4096
[  238.054130] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.054134] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.054137] dwc2 c90c0000.usb: DMA enabled
[  238.054141] dwc2 c90c0000.usb:   dwc2_release_channel: channel 6, halt_status 2
[  238.054147] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.054150] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.054154] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.054157] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.054163] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.054167] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.054176] dwc2 c90c0000.usb: DMA enabled
[  238.054179] dwc2 c90c0000.usb: desc DMA disabled
[  238.054183] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.054187] dwc2 c90c0000.usb: set HAINTMSK to 00000020
[  238.054191] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.054195] dwc2 c90c0000.usb: set HCCHAR(5) to 00c89200
[  238.054199] dwc2 c90c0000.usb: dwc2_hc_init: Channel 5
[  238.054202] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.054206] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.054209] dwc2 c90c0000.usb: 	 Is In: 1
[  238.054212] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.054216] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.054219] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.054223] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.054227] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.054230] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.054234] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.054238] dwc2 c90c0000.usb: no split
[  238.054242] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(5)
[  238.054246] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 5
[  238.054250] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.054253] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.054257] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.054261] dwc2 c90c0000.usb: Wrote 2e7a6000 to HCDMA(5)
[  238.054265] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.054269] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(5)
[  238.054273] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.054277] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.054301] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.054311] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.054316] dwc2 c90c0000.usb: urb_enqueue, urb f8714879
[  238.054320] dwc2 c90c0000.usb:   Device address: 3
[  238.054324] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.054327] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.054331] dwc2 c90c0000.usb:   Speed: HIGH
[  238.054335] dwc2 c90c0000.usb:   Max packet size: 512
[  238.054338] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.054343] dwc2 c90c0000.usb:   Transfer buffer: 2cd21e49, Transfer DMA: 1fb25000
[  238.054347] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.054350] dwc2 c90c0000.usb:   Interval: 0
[  238.054356] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.054360] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.054368] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.054375] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.054379] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.054382] dwc2 c90c0000.usb: HAINT=00000020
[  238.054386] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 5
[  238.054391] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.054395] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Channel Halted--
[  238.054399] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: DMA Channel Halted--
[  238.054403] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Transfer Complete--
[  238.054406] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.054411] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.054415] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 5
[  238.054419] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.054422] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.054426] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.054429] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.054433] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.054439] dwc2 c90c0000.usb: dwc2_host_complete: urb 67466227 device 3 ep 2-IN status 0 actual 4096
[  238.054444] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.054447] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.054451] dwc2 c90c0000.usb: DMA enabled
[  238.054455] dwc2 c90c0000.usb:   dwc2_release_channel: channel 5, halt_status 2
[  238.054460] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.054464] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.054467] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.054470] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.054476] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.054480] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.054483] dwc2 c90c0000.usb: DMA enabled
[  238.054486] dwc2 c90c0000.usb: desc DMA disabled
[  238.054490] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.054494] dwc2 c90c0000.usb: set HAINTMSK to 00000080
[  238.054498] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.054502] dwc2 c90c0000.usb: set HCCHAR(7) to 00c89200
[  238.054505] dwc2 c90c0000.usb: dwc2_hc_init: Channel 7
[  238.054509] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.054512] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.054516] dwc2 c90c0000.usb: 	 Is In: 1
[  238.054519] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.054523] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.054526] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.054530] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.054533] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.054537] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.054541] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.054544] dwc2 c90c0000.usb: no split
[  238.054549] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(7)
[  238.054553] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 7
[  238.054557] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.054561] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.054564] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.054568] dwc2 c90c0000.usb: Wrote 2e7ab000 to HCDMA(7)
[  238.054572] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.054576] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(7)
[  238.054580] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.054585] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.054626] dwc2 c90c0000.usb: urb_enqueue, urb 9084c402
[  238.054630] dwc2 c90c0000.usb:   Device address: 3
[  238.054634] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.054638] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.054641] dwc2 c90c0000.usb:   Speed: HIGH
[  238.054645] dwc2 c90c0000.usb:   Max packet size: 512
[  238.054649] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.054654] dwc2 c90c0000.usb:   Transfer buffer: 5297fbea, Transfer DMA: 2e78a000
[  238.054658] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.054661] dwc2 c90c0000.usb:   Interval: 0
[  238.054672] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.054677] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.054684] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.054688] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.054692] dwc2 c90c0000.usb: HAINT=00000080
[  238.054696] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 7
[  238.054700] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.054704] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Channel Halted--
[  238.054708] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: DMA Channel Halted--
[  238.054712] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Transfer Complete--
[  238.054716] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.054720] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.054724] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 7
[  238.054728] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.054731] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.054735] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.054738] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.054742] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.054748] dwc2 c90c0000.usb: dwc2_host_complete: urb a7ce381f device 3 ep 2-IN status 0 actual 4096
[  238.054753] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.054757] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.054760] dwc2 c90c0000.usb: DMA enabled
[  238.054765] dwc2 c90c0000.usb:   dwc2_release_channel: channel 7, halt_status 2
[  238.054770] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.054774] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.054777] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.054780] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.054786] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.054790] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.054793] dwc2 c90c0000.usb: DMA enabled
[  238.054796] dwc2 c90c0000.usb: desc DMA disabled
[  238.054800] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.054804] dwc2 c90c0000.usb: set HAINTMSK to 00000100
[  238.054808] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.054812] dwc2 c90c0000.usb: set HCCHAR(8) to 00c89200
[  238.054815] dwc2 c90c0000.usb: dwc2_hc_init: Channel 8
[  238.054819] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.054822] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.054826] dwc2 c90c0000.usb: 	 Is In: 1
[  238.054829] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.054833] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.054836] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.054841] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.054845] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.054848] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.054852] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.054856] dwc2 c90c0000.usb: no split
[  238.054860] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(8)
[  238.054864] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 8
[  238.054867] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.054871] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.054874] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.054879] dwc2 c90c0000.usb: Wrote 1fb27000 to HCDMA(8)
[  238.054882] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.054887] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(8)
[  238.054891] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.054895] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.054919] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.054925] dwc2 c90c0000.usb: urb_enqueue, urb 84dbe9e8
[  238.054928] dwc2 c90c0000.usb:   Device address: 3
[  238.054932] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.054936] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.054940] dwc2 c90c0000.usb:   Speed: HIGH
[  238.054943] dwc2 c90c0000.usb:   Max packet size: 512
[  238.054947] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.054951] dwc2 c90c0000.usb:   Transfer buffer: 9ed1989c, Transfer DMA: 2e79a000
[  238.054956] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.054959] dwc2 c90c0000.usb:   Interval: 0
[  238.054965] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.054970] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.054990] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.054999] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.055003] dwc2 c90c0000.usb: HAINT=00000100
[  238.055007] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 8
[  238.055011] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.055015] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Channel Halted--
[  238.055019] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: DMA Channel Halted--
[  238.055024] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Transfer Complete--
[  238.055027] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.055031] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.055036] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 8
[  238.055039] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.055043] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.055046] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.055050] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.055054] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.055060] dwc2 c90c0000.usb: dwc2_host_complete: urb 5f70d834 device 3 ep 2-IN status 0 actual 4096
[  238.055065] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.055069] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.055072] dwc2 c90c0000.usb: DMA enabled
[  238.055076] dwc2 c90c0000.usb:   dwc2_release_channel: channel 8, halt_status 2
[  238.055081] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.055085] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.055089] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.055092] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.055098] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.055101] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.055105] dwc2 c90c0000.usb: DMA enabled
[  238.055108] dwc2 c90c0000.usb: desc DMA disabled
[  238.055112] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.055116] dwc2 c90c0000.usb: set HAINTMSK to 00000200
[  238.055119] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.055124] dwc2 c90c0000.usb: set HCCHAR(9) to 00c89200
[  238.055127] dwc2 c90c0000.usb: dwc2_hc_init: Channel 9
[  238.055131] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.055134] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.055138] dwc2 c90c0000.usb: 	 Is In: 1
[  238.055141] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.055144] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.055148] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.055152] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.055155] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.055159] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.055163] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.055166] dwc2 c90c0000.usb: no split
[  238.055170] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(9)
[  238.055174] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 9
[  238.055178] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.055181] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.055185] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.055189] dwc2 c90c0000.usb: Wrote 1fbe2000 to HCDMA(9)
[  238.055192] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.055197] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(9)
[  238.055200] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.055205] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.055312] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.055316] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.055320] dwc2 c90c0000.usb: HAINT=00000200
[  238.055324] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 9
[  238.055329] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.055334] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Channel Halted--
[  238.055337] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: DMA Channel Halted--
[  238.055342] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Transfer Complete--
[  238.055345] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.055349] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.055354] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 9
[  238.055357] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.055361] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.055364] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.055368] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.055372] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.055378] dwc2 c90c0000.usb: dwc2_host_complete: urb c4a7e8a9 device 3 ep 2-IN status 0 actual 4096
[  238.055383] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.055386] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.055390] dwc2 c90c0000.usb: DMA enabled
[  238.055394] dwc2 c90c0000.usb:   dwc2_release_channel: channel 9, halt_status 2
[  238.055399] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.055403] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.055406] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.055409] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.055415] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.055419] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.055422] dwc2 c90c0000.usb: DMA enabled
[  238.055425] dwc2 c90c0000.usb: desc DMA disabled
[  238.055429] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.055433] dwc2 c90c0000.usb: set HAINTMSK to 00000400
[  238.055437] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.055442] dwc2 c90c0000.usb: set HCCHAR(10) to 00c89200
[  238.055445] dwc2 c90c0000.usb: dwc2_hc_init: Channel 10
[  238.055449] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.055452] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.055456] dwc2 c90c0000.usb: 	 Is In: 1
[  238.055459] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.055462] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.055466] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.055470] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.055474] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.055477] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.055481] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.055485] dwc2 c90c0000.usb: no split
[  238.055489] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(10)
[  238.055493] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 10
[  238.055497] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.055500] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.055504] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.055508] dwc2 c90c0000.usb: Wrote 1fb25000 to HCDMA(10)
[  238.055512] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.055516] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(10)
[  238.055520] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.055524] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.055618] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.055622] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.055626] dwc2 c90c0000.usb: HAINT=00000400
[  238.055630] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 10
[  238.055634] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.055639] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Channel Halted--
[  238.055642] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: DMA Channel Halted--
[  238.055646] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Transfer Complete--
[  238.055650] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.055654] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.055658] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 10
[  238.055662] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.055665] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.055669] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.055673] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.055676] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.055683] dwc2 c90c0000.usb: dwc2_host_complete: urb f8714879 device 3 ep 2-IN status 0 actual 4096
[  238.055687] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.055691] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.055694] dwc2 c90c0000.usb: DMA enabled
[  238.055698] dwc2 c90c0000.usb:   dwc2_release_channel: channel 10, halt_status 2
[  238.055704] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.055707] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.055710] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.055714] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.055719] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.055723] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.055726] dwc2 c90c0000.usb: DMA enabled
[  238.055730] dwc2 c90c0000.usb: desc DMA disabled
[  238.055733] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.055737] dwc2 c90c0000.usb: set HAINTMSK to 00000800
[  238.055741] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.055745] dwc2 c90c0000.usb: set HCCHAR(11) to 00c89200
[  238.055749] dwc2 c90c0000.usb: dwc2_hc_init: Channel 11
[  238.055752] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.055756] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.055759] dwc2 c90c0000.usb: 	 Is In: 1
[  238.055763] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.055766] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.055770] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.055773] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.055777] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.055781] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.055784] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.055788] dwc2 c90c0000.usb: no split
[  238.055797] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(11)
[  238.055801] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 11
[  238.055805] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.055808] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.055812] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.055816] dwc2 c90c0000.usb: Wrote 2e78a000 to HCDMA(11)
[  238.055820] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.055824] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(11)
[  238.055828] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.055832] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.055935] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.055939] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.055943] dwc2 c90c0000.usb: HAINT=00000800
[  238.055947] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 11
[  238.055952] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.055956] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Channel Halted--
[  238.055960] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: DMA Channel Halted--
[  238.055964] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Transfer Complete--
[  238.055967] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.055971] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.055976] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 11
[  238.055979] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.055983] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.055986] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.055990] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.055994] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.056000] dwc2 c90c0000.usb: dwc2_host_complete: urb 9084c402 device 3 ep 2-IN status 0 actual 4096
[  238.056005] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.056008] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.056012] dwc2 c90c0000.usb: DMA enabled
[  238.056016] dwc2 c90c0000.usb:   dwc2_release_channel: channel 11, halt_status 2
[  238.056021] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.056025] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.056028] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.056031] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.056037] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.056040] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.056044] dwc2 c90c0000.usb: DMA enabled
[  238.056047] dwc2 c90c0000.usb: desc DMA disabled
[  238.056051] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.056055] dwc2 c90c0000.usb: set HAINTMSK to 00001000
[  238.056058] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.056063] dwc2 c90c0000.usb: set HCCHAR(12) to 00c89200
[  238.056066] dwc2 c90c0000.usb: dwc2_hc_init: Channel 12
[  238.056070] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.056073] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.056077] dwc2 c90c0000.usb: 	 Is In: 1
[  238.056080] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.056083] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.056087] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.056091] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.056095] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.056098] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.056102] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.056105] dwc2 c90c0000.usb: no split
[  238.056110] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(12)
[  238.056114] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 12
[  238.056117] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.056121] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.056124] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.056128] dwc2 c90c0000.usb: Wrote 2e79a000 to HCDMA(12)
[  238.056132] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.056136] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(12)
[  238.056140] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.056145] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.056236] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.056240] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.056244] dwc2 c90c0000.usb: HAINT=00001000
[  238.056249] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 12
[  238.056253] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.056257] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Channel Halted--
[  238.056261] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: DMA Channel Halted--
[  238.056265] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Transfer Complete--
[  238.056268] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.056273] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.056277] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 12
[  238.056280] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.056284] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.056288] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.056291] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.056295] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.056302] dwc2 c90c0000.usb: dwc2_host_complete: urb 84dbe9e8 device 3 ep 2-IN status 0 actual 4096
[  238.056306] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.056310] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.056313] dwc2 c90c0000.usb: DMA enabled
[  238.056318] dwc2 c90c0000.usb:   dwc2_release_channel: channel 12, halt_status 2
[  238.056323] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.056326] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.056330] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.056334] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.056338] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.056379] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.056385] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.056389] dwc2 c90c0000.usb:   Device address: 3
[  238.056392] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.056396] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.056400] dwc2 c90c0000.usb:   Speed: HIGH
[  238.056404] dwc2 c90c0000.usb:   Max packet size: 512
[  238.056408] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.056412] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.056422] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.056425] dwc2 c90c0000.usb:   Interval: 0
[  238.056432] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.056437] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.056548] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.056553] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.056556] dwc2 c90c0000.usb: DMA enabled
[  238.056559] dwc2 c90c0000.usb: desc DMA disabled
[  238.056563] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.056567] dwc2 c90c0000.usb: set HAINTMSK to 00002000
[  238.056576] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.056581] dwc2 c90c0000.usb: set HCCHAR(13) to 00c89200
[  238.056584] dwc2 c90c0000.usb: dwc2_hc_init: Channel 13
[  238.056588] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.056591] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.056595] dwc2 c90c0000.usb: 	 Is In: 1
[  238.056599] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.056602] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.056606] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.056609] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.056613] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.056617] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.056621] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.056624] dwc2 c90c0000.usb: no split
[  238.056629] dwc2 c90c0000.usb: Wrote 40080200 to HCTSIZ(13)
[  238.056632] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 13
[  238.056636] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.056639] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.056643] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.056647] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(13)
[  238.056651] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.056655] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(13)
[  238.056676] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.056680] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.056684] dwc2 c90c0000.usb: HAINT=00002000
[  238.056689] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 13
[  238.056693] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.056697] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Channel Halted--
[  238.056701] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: DMA Channel Halted--
[  238.056706] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Transfer Complete--
[  238.056709] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.056713] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.056718] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 13
[  238.056722] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.056725] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.056729] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.056733] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.056737] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.056743] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.056748] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.056752] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.056755] dwc2 c90c0000.usb: DMA enabled
[  238.056760] dwc2 c90c0000.usb:   dwc2_release_channel: channel 13, halt_status 2
[  238.056765] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.056768] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.056771] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.056776] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.056780] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.057215] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.057225] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.057229] dwc2 c90c0000.usb:   Device address: 3
[  238.057234] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.057238] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.057241] dwc2 c90c0000.usb:   Speed: HIGH
[  238.057245] dwc2 c90c0000.usb:   Max packet size: 512
[  238.057250] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.057254] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.057259] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.057262] dwc2 c90c0000.usb:   Interval: 0
[  238.057270] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.057275] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.057300] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.057305] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.057309] dwc2 c90c0000.usb: DMA enabled
[  238.057312] dwc2 c90c0000.usb: desc DMA disabled
[  238.057316] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.057320] dwc2 c90c0000.usb: set HAINTMSK to 00004000
[  238.057324] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.057328] dwc2 c90c0000.usb: set HCCHAR(14) to 00c80a00
[  238.057332] dwc2 c90c0000.usb: dwc2_hc_init: Channel 14
[  238.057336] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.057339] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.057343] dwc2 c90c0000.usb: 	 Is In: 0
[  238.057346] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.057349] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.057353] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.057357] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.057361] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.057365] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.057369] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.057373] dwc2 c90c0000.usb: no split
[  238.057377] dwc2 c90c0000.usb: Wrote 0008001f to HCTSIZ(14)
[  238.057381] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 14
[  238.057385] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.057388] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.057392] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.057396] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(14)
[  238.057400] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.057404] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(14)
[  238.057417] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.057421] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.057425] dwc2 c90c0000.usb: HAINT=00004000
[  238.057429] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 14
[  238.057434] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.057438] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Channel Halted--
[  238.057442] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: DMA Channel Halted--
[  238.057446] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Transfer Complete--
[  238.057456] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.057461] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.057465] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 14
[  238.057469] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.057472] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.057476] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.057479] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.057483] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.057490] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.057495] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.057500] dwc2 c90c0000.usb:   dwc2_release_channel: channel 14, halt_status 2
[  238.057506] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.057510] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.057513] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.057518] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.057523] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.057575] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.057582] dwc2 c90c0000.usb: urb_enqueue, urb 544633e2
[  238.057585] dwc2 c90c0000.usb:   Device address: 3
[  238.057589] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.057593] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.057597] dwc2 c90c0000.usb:   Speed: HIGH
[  238.057601] dwc2 c90c0000.usb:   Max packet size: 512
[  238.057605] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.057609] dwc2 c90c0000.usb:   Transfer buffer: 640b4f27, Transfer DMA: 1f8c4000
[  238.057614] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.057617] dwc2 c90c0000.usb:   Interval: 0
[  238.057623] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.057629] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.057638] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.057643] dwc2 c90c0000.usb: urb_enqueue, urb cd91f79f
[  238.057646] dwc2 c90c0000.usb:   Device address: 3
[  238.057650] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.057654] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.057657] dwc2 c90c0000.usb:   Speed: HIGH
[  238.057661] dwc2 c90c0000.usb:   Max packet size: 512
[  238.057664] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.057672] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.057676] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.057680] dwc2 c90c0000.usb: DMA enabled
[  238.057683] dwc2 c90c0000.usb: desc DMA disabled
[  238.057687] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.057691] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[  238.057694] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.057699] dwc2 c90c0000.usb: set HCCHAR(0) to 00c89200
[  238.057702] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[  238.057707] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.057710] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.057713] dwc2 c90c0000.usb: 	 Is In: 1
[  238.057717] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.057720] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.057724] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.057728] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.057732] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.057736] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.057740] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.057743] dwc2 c90c0000.usb: no split
[  238.057748] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(0)
[  238.057752] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[  238.057755] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.057759] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.057762] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.057766] dwc2 c90c0000.usb: Wrote 1f8c4000 to HCDMA(0)
[  238.057770] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.057774] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(0)
[  238.057782] dwc2 c90c0000.usb:   Transfer buffer: aec17d84, Transfer DMA: 1f8c7000
[  238.057786] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.057790] dwc2 c90c0000.usb:   Interval: 0
[  238.057800] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.057804] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.057812] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.057817] dwc2 c90c0000.usb: urb_enqueue, urb 67466227
[  238.057821] dwc2 c90c0000.usb:   Device address: 3
[  238.057825] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.057829] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.057832] dwc2 c90c0000.usb:   Speed: HIGH
[  238.057836] dwc2 c90c0000.usb:   Max packet size: 512
[  238.057839] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.057844] dwc2 c90c0000.usb:   Transfer buffer: 7f2fa21b, Transfer DMA: 2e72d000
[  238.057848] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.057851] dwc2 c90c0000.usb:   Interval: 0
[  238.057857] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.057861] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.057868] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.057875] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.057879] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.057882] dwc2 c90c0000.usb: HAINT=00000001
[  238.057886] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[  238.057891] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.057895] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Channel Halted--
[  238.057900] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: DMA Channel Halted--
[  238.057904] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Transfer Complete--
[  238.057908] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.057912] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.057916] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 0
[  238.057920] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.057923] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.057927] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.057931] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.057934] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.057941] dwc2 c90c0000.usb: dwc2_host_complete: urb 544633e2 device 3 ep 2-IN status 0 actual 4096
[  238.057947] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.057950] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.057953] dwc2 c90c0000.usb: DMA enabled
[  238.057958] dwc2 c90c0000.usb:   dwc2_release_channel: channel 0, halt_status 2
[  238.057964] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.057967] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.057971] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.057974] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.057980] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.057983] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.057987] dwc2 c90c0000.usb: DMA enabled
[  238.057990] dwc2 c90c0000.usb: desc DMA disabled
[  238.057994] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.057997] dwc2 c90c0000.usb: set HAINTMSK to 00008000
[  238.058002] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.058006] dwc2 c90c0000.usb: set HCCHAR(15) to 00c89200
[  238.058010] dwc2 c90c0000.usb: dwc2_hc_init: Channel 15
[  238.058013] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.058017] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.058020] dwc2 c90c0000.usb: 	 Is In: 1
[  238.058023] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.058027] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.058030] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.058034] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.058038] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.058042] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.058046] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.058049] dwc2 c90c0000.usb: no split
[  238.058053] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(15)
[  238.058057] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 15
[  238.058061] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.058064] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.058068] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.058072] dwc2 c90c0000.usb: Wrote 1f8c7000 to HCDMA(15)
[  238.058076] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.058080] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(15)
[  238.058084] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.058088] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.058107] dwc2 c90c0000.usb: urb_enqueue, urb a7ce381f
[  238.058111] dwc2 c90c0000.usb:   Device address: 3
[  238.058115] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.058119] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.058122] dwc2 c90c0000.usb:   Speed: HIGH
[  238.058126] dwc2 c90c0000.usb:   Max packet size: 512
[  238.058130] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.058134] dwc2 c90c0000.usb:   Transfer buffer: 31251977, Transfer DMA: 1fce0000
[  238.058138] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.058142] dwc2 c90c0000.usb:   Interval: 0
[  238.058148] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.058152] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.058163] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.058172] dwc2 c90c0000.usb: urb_enqueue, urb 5f70d834
[  238.058176] dwc2 c90c0000.usb:   Device address: 3
[  238.058182] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.058186] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.058190] dwc2 c90c0000.usb: HAINT=00008000
[  238.058194] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 15
[  238.058198] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.058202] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Channel Halted--
[  238.058206] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: DMA Channel Halted--
[  238.058211] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Transfer Complete--
[  238.058214] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.058218] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.058223] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 15
[  238.058226] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.058230] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.058233] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.058237] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.058241] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.058247] dwc2 c90c0000.usb: dwc2_host_complete: urb cd91f79f device 3 ep 2-IN status 0 actual 4096
[  238.058252] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.058255] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.058259] dwc2 c90c0000.usb: DMA enabled
[  238.058263] dwc2 c90c0000.usb:   dwc2_release_channel: channel 15, halt_status 2
[  238.058269] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.058273] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.058276] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.058279] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.058285] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.058289] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.058298] dwc2 c90c0000.usb: DMA enabled
[  238.058301] dwc2 c90c0000.usb: desc DMA disabled
[  238.058305] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.058309] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[  238.058313] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.058317] dwc2 c90c0000.usb: set HCCHAR(1) to 00c89200
[  238.058321] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[  238.058325] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.058328] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.058331] dwc2 c90c0000.usb: 	 Is In: 1
[  238.058335] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.058338] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.058342] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.058346] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.058349] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.058353] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.058357] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.058360] dwc2 c90c0000.usb: no split
[  238.058364] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(1)
[  238.058368] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[  238.058372] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.058376] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.058379] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.058383] dwc2 c90c0000.usb: Wrote 2e72d000 to HCDMA(1)
[  238.058387] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.058391] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(1)
[  238.058396] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.058400] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.058415] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.058423] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.058427] dwc2 c90c0000.usb:   Speed: HIGH
[  238.058431] dwc2 c90c0000.usb:   Max packet size: 512
[  238.058435] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.058440] dwc2 c90c0000.usb:   Transfer buffer: bb11cea0, Transfer DMA: 2e21d000
[  238.058444] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.058447] dwc2 c90c0000.usb:   Interval: 0
[  238.058453] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.058457] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.058466] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.058471] dwc2 c90c0000.usb: urb_enqueue, urb c4a7e8a9
[  238.058474] dwc2 c90c0000.usb:   Device address: 3
[  238.058478] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.058482] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.058485] dwc2 c90c0000.usb:   Speed: HIGH
[  238.058491] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.058495] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.058498] dwc2 c90c0000.usb: HAINT=00000002
[  238.058502] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[  238.058507] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.058511] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[  238.058514] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[  238.058519] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[  238.058522] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.058526] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.058531] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 1
[  238.058534] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.058538] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.058541] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.058545] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.058549] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.058555] dwc2 c90c0000.usb: dwc2_host_complete: urb 67466227 device 3 ep 2-IN status 0 actual 4096
[  238.058560] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.058564] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.058567] dwc2 c90c0000.usb: DMA enabled
[  238.058571] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 2
[  238.058576] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.058580] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.058583] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.058587] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.058592] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.058596] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.058599] dwc2 c90c0000.usb: DMA enabled
[  238.058602] dwc2 c90c0000.usb: desc DMA disabled
[  238.058606] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.058610] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[  238.058613] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.058617] dwc2 c90c0000.usb: set HCCHAR(2) to 00c89200
[  238.058621] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[  238.058625] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.058628] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.058632] dwc2 c90c0000.usb: 	 Is In: 1
[  238.058635] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.058638] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.058642] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.058646] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.058650] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.058653] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.058657] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.058660] dwc2 c90c0000.usb: no split
[  238.058665] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(2)
[  238.058669] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[  238.058672] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.058676] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.058679] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.058683] dwc2 c90c0000.usb: Wrote 1fce0000 to HCDMA(2)
[  238.058687] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.058691] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(2)
[  238.058695] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.058700] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.058717] dwc2 c90c0000.usb:   Max packet size: 512
[  238.058721] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.058726] dwc2 c90c0000.usb:   Transfer buffer: 57c85e09, Transfer DMA: 1fddd000
[  238.058730] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.058733] dwc2 c90c0000.usb:   Interval: 0
[  238.058739] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.058744] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.058753] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.058757] dwc2 c90c0000.usb: urb_enqueue, urb f8714879
[  238.058761] dwc2 c90c0000.usb:   Device address: 3
[  238.058764] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.058768] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.058772] dwc2 c90c0000.usb:   Speed: HIGH
[  238.058775] dwc2 c90c0000.usb:   Max packet size: 512
[  238.058779] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.058784] dwc2 c90c0000.usb:   Transfer buffer: b644467f, Transfer DMA: 1f84b000
[  238.058791] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.058795] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.058798] dwc2 c90c0000.usb: HAINT=00000004
[  238.058802] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[  238.058807] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.058811] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[  238.058814] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[  238.058819] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[  238.058822] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.058827] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.058831] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 2
[  238.058835] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.058838] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.058842] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.058845] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.058849] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.058855] dwc2 c90c0000.usb: dwc2_host_complete: urb a7ce381f device 3 ep 2-IN status 0 actual 4096
[  238.058860] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.058864] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.058867] dwc2 c90c0000.usb: DMA enabled
[  238.058871] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 2
[  238.058877] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.058881] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.058884] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.058887] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.058892] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.058896] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.058899] dwc2 c90c0000.usb: DMA enabled
[  238.058903] dwc2 c90c0000.usb: desc DMA disabled
[  238.058906] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.058910] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[  238.058914] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.058918] dwc2 c90c0000.usb: set HCCHAR(3) to 00c89200
[  238.058922] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[  238.058925] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.058929] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.058932] dwc2 c90c0000.usb: 	 Is In: 1
[  238.058936] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.058939] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.058943] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.058946] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.058950] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.058954] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.058957] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.058961] dwc2 c90c0000.usb: no split
[  238.058965] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(3)
[  238.058969] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[  238.058972] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.058976] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.058979] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.058984] dwc2 c90c0000.usb: Wrote 2e21d000 to HCDMA(3)
[  238.058987] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.058991] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(3)
[  238.058995] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.059000] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.059015] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.059020] dwc2 c90c0000.usb:   Interval: 0
[  238.059026] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.059030] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.059039] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.059049] dwc2 c90c0000.usb: urb_enqueue, urb 9084c402
[  238.059052] dwc2 c90c0000.usb:   Device address: 3
[  238.059056] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.059060] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.059063] dwc2 c90c0000.usb:   Speed: HIGH
[  238.059067] dwc2 c90c0000.usb:   Max packet size: 512
[  238.059071] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.059075] dwc2 c90c0000.usb:   Transfer buffer: a7bc3b7d, Transfer DMA: 2e248000
[  238.059084] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.059091] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.059094] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.059098] dwc2 c90c0000.usb: HAINT=00000008
[  238.059102] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[  238.059106] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.059111] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[  238.059115] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[  238.059119] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[  238.059122] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.059126] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.059131] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 3
[  238.059134] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.059138] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.059142] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.059145] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.059149] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.059155] dwc2 c90c0000.usb: dwc2_host_complete: urb 5f70d834 device 3 ep 2-IN status 0 actual 4096
[  238.059160] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.059164] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.059167] dwc2 c90c0000.usb: DMA enabled
[  238.059171] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 2
[  238.059177] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.059180] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.059184] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.059187] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.059192] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.059196] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.059199] dwc2 c90c0000.usb: DMA enabled
[  238.059203] dwc2 c90c0000.usb: desc DMA disabled
[  238.059206] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.059210] dwc2 c90c0000.usb: set HAINTMSK to 00000010
[  238.059214] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.059218] dwc2 c90c0000.usb: set HCCHAR(4) to 00c89200
[  238.059222] dwc2 c90c0000.usb: dwc2_hc_init: Channel 4
[  238.059226] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.059229] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.059232] dwc2 c90c0000.usb: 	 Is In: 1
[  238.059236] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.059239] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.059243] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.059247] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.059250] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.059254] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.059258] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.059261] dwc2 c90c0000.usb: no split
[  238.059266] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(4)
[  238.059270] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 4
[  238.059273] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.059277] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.059280] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.059285] dwc2 c90c0000.usb: Wrote 1fddd000 to HCDMA(4)
[  238.059289] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.059293] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(4)
[  238.059297] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.059301] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.059316] dwc2 c90c0000.usb:   Interval: 0
[  238.059323] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.059328] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.059336] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.059341] dwc2 c90c0000.usb: urb_enqueue, urb 84dbe9e8
[  238.059344] dwc2 c90c0000.usb:   Device address: 3
[  238.059348] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.059352] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.059355] dwc2 c90c0000.usb:   Speed: HIGH
[  238.059359] dwc2 c90c0000.usb:   Max packet size: 512
[  238.059363] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.059367] dwc2 c90c0000.usb:   Transfer buffer: d100fec5, Transfer DMA: 1fb21000
[  238.059372] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.059375] dwc2 c90c0000.usb:   Interval: 0
[  238.059380] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.059385] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.059392] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.059396] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.059399] dwc2 c90c0000.usb: HAINT=00000010
[  238.059403] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 4
[  238.059408] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.059412] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Channel Halted--
[  238.059416] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: DMA Channel Halted--
[  238.059420] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Transfer Complete--
[  238.059423] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.059427] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.059432] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 4
[  238.059435] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.059439] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.059442] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.059446] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.059450] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.059456] dwc2 c90c0000.usb: dwc2_host_complete: urb c4a7e8a9 device 3 ep 2-IN status 0 actual 4096
[  238.059461] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.059464] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.059467] dwc2 c90c0000.usb: DMA enabled
[  238.059472] dwc2 c90c0000.usb:   dwc2_release_channel: channel 4, halt_status 2
[  238.059477] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.059480] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.059484] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.059487] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.059492] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.059496] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.059499] dwc2 c90c0000.usb: DMA enabled
[  238.059503] dwc2 c90c0000.usb: desc DMA disabled
[  238.059506] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.059510] dwc2 c90c0000.usb: set HAINTMSK to 00000040
[  238.059514] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.059518] dwc2 c90c0000.usb: set HCCHAR(6) to 00c89200
[  238.059522] dwc2 c90c0000.usb: dwc2_hc_init: Channel 6
[  238.059525] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.059529] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.059532] dwc2 c90c0000.usb: 	 Is In: 1
[  238.059536] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.059539] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.059542] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.059546] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.059550] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.059554] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.059557] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.059561] dwc2 c90c0000.usb: no split
[  238.059565] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(6)
[  238.059569] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 6
[  238.059573] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.059576] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.059579] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.059584] dwc2 c90c0000.usb: Wrote 1f84b000 to HCDMA(6)
[  238.059587] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.059592] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(6)
[  238.059595] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.059600] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.059619] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.059624] dwc2 c90c0000.usb: urb_enqueue, urb d4475b7d
[  238.059628] dwc2 c90c0000.usb:   Device address: 3
[  238.059632] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.059636] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.059639] dwc2 c90c0000.usb:   Speed: HIGH
[  238.059643] dwc2 c90c0000.usb:   Max packet size: 512
[  238.059646] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.059651] dwc2 c90c0000.usb:   Transfer buffer: df8b412f, Transfer DMA: 1fc0a000
[  238.059655] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.059658] dwc2 c90c0000.usb:   Interval: 0
[  238.059664] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.059673] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.059681] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.059686] dwc2 c90c0000.usb: urb_enqueue, urb a7f6c107
[  238.059693] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.059697] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.059700] dwc2 c90c0000.usb: HAINT=00000040
[  238.059704] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 6
[  238.059709] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.059712] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Channel Halted--
[  238.059716] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: DMA Channel Halted--
[  238.059721] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Transfer Complete--
[  238.059724] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.059728] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.059733] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 6
[  238.059737] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.059740] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.059744] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.059748] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.059751] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.059758] dwc2 c90c0000.usb: dwc2_host_complete: urb f8714879 device 3 ep 2-IN status 0 actual 4096
[  238.059763] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.059767] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.059770] dwc2 c90c0000.usb: DMA enabled
[  238.059774] dwc2 c90c0000.usb:   dwc2_release_channel: channel 6, halt_status 2
[  238.059779] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.059783] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.059786] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.059790] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.059795] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.059799] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.059802] dwc2 c90c0000.usb: DMA enabled
[  238.059805] dwc2 c90c0000.usb: desc DMA disabled
[  238.059809] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.059813] dwc2 c90c0000.usb: set HAINTMSK to 00000020
[  238.059817] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.059821] dwc2 c90c0000.usb: set HCCHAR(5) to 00c89200
[  238.059825] dwc2 c90c0000.usb: dwc2_hc_init: Channel 5
[  238.059828] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.059832] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.059835] dwc2 c90c0000.usb: 	 Is In: 1
[  238.059839] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.059842] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.059846] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.059849] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.059853] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.059857] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.059860] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.059864] dwc2 c90c0000.usb: no split
[  238.059868] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(5)
[  238.059872] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 5
[  238.059876] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.059879] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.059883] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.059887] dwc2 c90c0000.usb: Wrote 2e248000 to HCDMA(5)
[  238.059891] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.059895] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(5)
[  238.059899] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.059904] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.059922] dwc2 c90c0000.usb:   Device address: 3
[  238.059927] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.059936] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.059940] dwc2 c90c0000.usb:   Speed: HIGH
[  238.059944] dwc2 c90c0000.usb:   Max packet size: 512
[  238.059947] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.059952] dwc2 c90c0000.usb:   Transfer buffer: c14abccb, Transfer DMA: 1f9c8000
[  238.059956] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.059959] dwc2 c90c0000.usb:   Interval: 0
[  238.059965] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.059970] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.059979] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.059983] dwc2 c90c0000.usb: urb_enqueue, urb 8c3fa95c
[  238.059987] dwc2 c90c0000.usb:   Device address: 3
[  238.059990] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.059994] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.060001] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.060004] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.060008] dwc2 c90c0000.usb: HAINT=00000020
[  238.060012] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 5
[  238.060016] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.060021] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Channel Halted--
[  238.060025] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: DMA Channel Halted--
[  238.060029] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Transfer Complete--
[  238.060032] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.060037] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.060041] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 5
[  238.060044] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.060048] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.060052] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.060056] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.060060] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.060066] dwc2 c90c0000.usb: dwc2_host_complete: urb 9084c402 device 3 ep 2-IN status 0 actual 4096
[  238.060071] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.060075] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.060078] dwc2 c90c0000.usb: DMA enabled
[  238.060082] dwc2 c90c0000.usb:   dwc2_release_channel: channel 5, halt_status 2
[  238.060087] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.060091] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.060094] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.060098] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.060103] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.060107] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.060110] dwc2 c90c0000.usb: DMA enabled
[  238.060113] dwc2 c90c0000.usb: desc DMA disabled
[  238.060117] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.060121] dwc2 c90c0000.usb: set HAINTMSK to 00000080
[  238.060125] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.060129] dwc2 c90c0000.usb: set HCCHAR(7) to 00c89200
[  238.060133] dwc2 c90c0000.usb: dwc2_hc_init: Channel 7
[  238.060136] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.060140] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.060143] dwc2 c90c0000.usb: 	 Is In: 1
[  238.060146] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.060150] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.060153] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.060157] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.060161] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.060164] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.060168] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.060171] dwc2 c90c0000.usb: no split
[  238.060176] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(7)
[  238.060179] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 7
[  238.060183] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.060186] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.060190] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.060194] dwc2 c90c0000.usb: Wrote 1fb21000 to HCDMA(7)
[  238.060198] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.060202] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(7)
[  238.060206] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.060210] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.060226] dwc2 c90c0000.usb:   Speed: HIGH
[  238.060230] dwc2 c90c0000.usb:   Max packet size: 512
[  238.060234] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.060238] dwc2 c90c0000.usb:   Transfer buffer: 569bf2b3, Transfer DMA: 2d2b6000
[  238.060243] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.060246] dwc2 c90c0000.usb:   Interval: 0
[  238.060251] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.060256] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.060264] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.060268] dwc2 c90c0000.usb: urb_enqueue, urb 3d621ba8
[  238.060272] dwc2 c90c0000.usb:   Device address: 3
[  238.060275] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.060279] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.060283] dwc2 c90c0000.usb:   Speed: HIGH
[  238.060286] dwc2 c90c0000.usb:   Max packet size: 512
[  238.060290] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.060298] dwc2 c90c0000.usb:   Transfer buffer: a1e448e3, Transfer DMA: 2e25e000
[  238.060303] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.060309] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.060312] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.060316] dwc2 c90c0000.usb: HAINT=00000080
[  238.060320] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 7
[  238.060324] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.060328] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Channel Halted--
[  238.060332] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: DMA Channel Halted--
[  238.060336] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Transfer Complete--
[  238.060340] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.060344] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.060348] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 7
[  238.060352] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.060355] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.060359] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.060362] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.060366] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.060372] dwc2 c90c0000.usb: dwc2_host_complete: urb 84dbe9e8 device 3 ep 2-IN status 0 actual 4096
[  238.060377] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.060381] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.060384] dwc2 c90c0000.usb: DMA enabled
[  238.060389] dwc2 c90c0000.usb:   dwc2_release_channel: channel 7, halt_status 2
[  238.060394] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.060398] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.060401] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.060404] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.060409] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.060414] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.060417] dwc2 c90c0000.usb: DMA enabled
[  238.060420] dwc2 c90c0000.usb: desc DMA disabled
[  238.060424] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.060428] dwc2 c90c0000.usb: set HAINTMSK to 00000100
[  238.060432] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.060436] dwc2 c90c0000.usb: set HCCHAR(8) to 00c89200
[  238.060439] dwc2 c90c0000.usb: dwc2_hc_init: Channel 8
[  238.060443] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.060447] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.060450] dwc2 c90c0000.usb: 	 Is In: 1
[  238.060454] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.060457] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.060460] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.060464] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.060468] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.060472] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.060475] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.060479] dwc2 c90c0000.usb: no split
[  238.060483] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(8)
[  238.060487] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 8
[  238.060491] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.060494] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.060498] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.060502] dwc2 c90c0000.usb: Wrote 1fc0a000 to HCDMA(8)
[  238.060506] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.060510] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(8)
[  238.060514] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.060518] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.060535] dwc2 c90c0000.usb:   Interval: 0
[  238.060546] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.060551] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.060560] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.060565] dwc2 c90c0000.usb: urb_enqueue, urb 6510a936
[  238.060568] dwc2 c90c0000.usb:   Device address: 3
[  238.060572] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.060576] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.060579] dwc2 c90c0000.usb:   Speed: HIGH
[  238.060583] dwc2 c90c0000.usb:   Max packet size: 512
[  238.060587] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.060591] dwc2 c90c0000.usb:   Transfer buffer: d0a61113, Transfer DMA: 1fcec000
[  238.060596] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.060599] dwc2 c90c0000.usb:   Interval: 0
[  238.060604] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.060611] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.060614] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.060618] dwc2 c90c0000.usb: HAINT=00000100
[  238.060622] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 8
[  238.060626] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.060630] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Channel Halted--
[  238.060634] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: DMA Channel Halted--
[  238.060638] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Transfer Complete--
[  238.060642] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.060646] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.060650] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 8
[  238.060654] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.060657] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.060661] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.060664] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.060668] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.060674] dwc2 c90c0000.usb: dwc2_host_complete: urb d4475b7d device 3 ep 2-IN status 0 actual 4096
[  238.060679] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.060683] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.060686] dwc2 c90c0000.usb: DMA enabled
[  238.060691] dwc2 c90c0000.usb:   dwc2_release_channel: channel 8, halt_status 2
[  238.060696] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.060699] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.060703] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.060706] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.060711] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.060721] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.060724] dwc2 c90c0000.usb: DMA enabled
[  238.060727] dwc2 c90c0000.usb: desc DMA disabled
[  238.060731] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.060735] dwc2 c90c0000.usb: set HAINTMSK to 00000200
[  238.060739] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.060743] dwc2 c90c0000.usb: set HCCHAR(9) to 00c89200
[  238.060746] dwc2 c90c0000.usb: dwc2_hc_init: Channel 9
[  238.060750] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.060753] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.060757] dwc2 c90c0000.usb: 	 Is In: 1
[  238.060760] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.060764] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.060767] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.060771] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.060775] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.060778] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.060782] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.060785] dwc2 c90c0000.usb: no split
[  238.060790] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(9)
[  238.060794] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 9
[  238.060797] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.060801] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.060804] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.060808] dwc2 c90c0000.usb: Wrote 1f9c8000 to HCDMA(9)
[  238.060812] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.060816] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(9)
[  238.060820] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.060825] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.060842] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.060851] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.060856] dwc2 c90c0000.usb: urb_enqueue, urb 6eb02129
[  238.060859] dwc2 c90c0000.usb:   Device address: 3
[  238.060863] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.060867] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.060870] dwc2 c90c0000.usb:   Speed: HIGH
[  238.060874] dwc2 c90c0000.usb:   Max packet size: 512
[  238.060878] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.060882] dwc2 c90c0000.usb:   Transfer buffer: fc4bff01, Transfer DMA: 1fe22000
[  238.060887] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.060890] dwc2 c90c0000.usb:   Interval: 0
[  238.060896] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.060900] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.060907] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.060912] dwc2 c90c0000.usb: urb_enqueue, urb 0e85fd4b
[  238.060918] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000008
[  238.060922] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.060926] dwc2 c90c0000.usb: HAINT=00000200
[  238.060930] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 9
[  238.060934] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.060938] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Channel Halted--
[  238.060942] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: DMA Channel Halted--
[  238.060946] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Transfer Complete--
[  238.060950] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.060954] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.060958] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 9
[  238.060962] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.060965] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.060969] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.060973] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.060976] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.060982] dwc2 c90c0000.usb: dwc2_host_complete: urb a7f6c107 device 3 ep 2-IN status 0 actual 4096
[  238.060987] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.060991] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.060994] dwc2 c90c0000.usb: DMA enabled
[  238.060998] dwc2 c90c0000.usb:   dwc2_release_channel: channel 9, halt_status 2
[  238.061003] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.061007] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.061010] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.061014] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.061019] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.061023] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.061026] dwc2 c90c0000.usb: DMA enabled
[  238.061029] dwc2 c90c0000.usb: desc DMA disabled
[  238.061033] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.061037] dwc2 c90c0000.usb: set HAINTMSK to 00000400
[  238.061040] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.061045] dwc2 c90c0000.usb: set HCCHAR(10) to 00c89200
[  238.061048] dwc2 c90c0000.usb: dwc2_hc_init: Channel 10
[  238.061052] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.061055] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.061059] dwc2 c90c0000.usb: 	 Is In: 1
[  238.061062] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.061066] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.061069] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.061073] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.061077] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.061080] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.061084] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.061088] dwc2 c90c0000.usb: no split
[  238.061092] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(10)
[  238.061096] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 10
[  238.061099] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.061103] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.061106] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.061111] dwc2 c90c0000.usb: Wrote 2d2b6000 to HCDMA(10)
[  238.061115] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.061119] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(10)
[  238.061123] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.061127] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.061144] dwc2 c90c0000.usb:   Device address: 3
[  238.061148] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.061152] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.061155] dwc2 c90c0000.usb:   Speed: HIGH
[  238.061159] dwc2 c90c0000.usb:   Max packet size: 512
[  238.061162] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.061171] dwc2 c90c0000.usb:   Transfer buffer: cd4633c4, Transfer DMA: 1fe8d000
[  238.061176] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.061179] dwc2 c90c0000.usb:   Interval: 0
[  238.061185] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.061189] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.061198] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.061202] dwc2 c90c0000.usb: urb_enqueue, urb 9ed6427f
[  238.061206] dwc2 c90c0000.usb:   Device address: 3
[  238.061209] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.061213] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.061219] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.061223] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.061226] dwc2 c90c0000.usb: HAINT=00000400
[  238.061231] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 10
[  238.061235] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.061239] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Channel Halted--
[  238.061243] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: DMA Channel Halted--
[  238.061247] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Transfer Complete--
[  238.061250] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.061254] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.061259] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 10
[  238.061262] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.061266] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.061269] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.061273] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.061277] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.061283] dwc2 c90c0000.usb: dwc2_host_complete: urb 8c3fa95c device 3 ep 2-IN status 0 actual 4096
[  238.061288] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.061291] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.061294] dwc2 c90c0000.usb: DMA enabled
[  238.061299] dwc2 c90c0000.usb:   dwc2_release_channel: channel 10, halt_status 2
[  238.061304] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.061308] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.061311] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.061315] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.061320] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.061324] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.061327] dwc2 c90c0000.usb: DMA enabled
[  238.061330] dwc2 c90c0000.usb: desc DMA disabled
[  238.061334] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.061338] dwc2 c90c0000.usb: set HAINTMSK to 00000800
[  238.061342] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.061346] dwc2 c90c0000.usb: set HCCHAR(11) to 00c89200
[  238.061350] dwc2 c90c0000.usb: dwc2_hc_init: Channel 11
[  238.061353] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.061357] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.061360] dwc2 c90c0000.usb: 	 Is In: 1
[  238.061363] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.061367] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.061370] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.061374] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.061378] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.061382] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.061386] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.061389] dwc2 c90c0000.usb: no split
[  238.061393] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(11)
[  238.061397] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 11
[  238.061401] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.061404] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.061407] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.061412] dwc2 c90c0000.usb: Wrote 2e25e000 to HCDMA(11)
[  238.061415] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.061420] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(11)
[  238.061424] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.061428] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.061458] dwc2 c90c0000.usb:   Speed: HIGH
[  238.061463] dwc2 c90c0000.usb:   Max packet size: 512
[  238.061466] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.061471] dwc2 c90c0000.usb:   Transfer buffer: d37463f4, Transfer DMA: 1fe2e000
[  238.061475] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.061479] dwc2 c90c0000.usb:   Interval: 0
[  238.061485] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.061495] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.061504] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.061508] dwc2 c90c0000.usb: urb_enqueue, urb 0cce8d45
[  238.061512] dwc2 c90c0000.usb:   Device address: 3
[  238.061519] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.061522] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.061526] dwc2 c90c0000.usb: HAINT=00000800
[  238.061530] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 11
[  238.061535] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.061539] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Channel Halted--
[  238.061542] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: DMA Channel Halted--
[  238.061547] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Transfer Complete--
[  238.061550] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.061554] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.061559] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 11
[  238.061562] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.061566] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.061569] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.061573] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.061577] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.061583] dwc2 c90c0000.usb: dwc2_host_complete: urb 3d621ba8 device 3 ep 2-IN status 0 actual 4096
[  238.061588] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.061591] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.061595] dwc2 c90c0000.usb: DMA enabled
[  238.061599] dwc2 c90c0000.usb:   dwc2_release_channel: channel 11, halt_status 2
[  238.061604] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.061608] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.061611] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.061614] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.061620] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.061623] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.061627] dwc2 c90c0000.usb: DMA enabled
[  238.061630] dwc2 c90c0000.usb: desc DMA disabled
[  238.061634] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.061638] dwc2 c90c0000.usb: set HAINTMSK to 00001000
[  238.061642] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.061646] dwc2 c90c0000.usb: set HCCHAR(12) to 00c89200
[  238.061650] dwc2 c90c0000.usb: dwc2_hc_init: Channel 12
[  238.061653] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.061657] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.061660] dwc2 c90c0000.usb: 	 Is In: 1
[  238.061664] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.061667] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.061671] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.061675] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.061678] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.061682] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.061686] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.061689] dwc2 c90c0000.usb: no split
[  238.061694] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(12)
[  238.061698] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 12
[  238.061701] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.061704] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.061708] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.061712] dwc2 c90c0000.usb: Wrote 1fcec000 to HCDMA(12)
[  238.061716] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.061720] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(12)
[  238.061724] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.061729] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.061748] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.061753] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.061756] dwc2 c90c0000.usb:   Speed: HIGH
[  238.061760] dwc2 c90c0000.usb:   Max packet size: 512
[  238.061764] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.061768] dwc2 c90c0000.usb:   Transfer buffer: 8051dfe6, Transfer DMA: 1fc80000
[  238.061773] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.061776] dwc2 c90c0000.usb:   Interval: 0
[  238.061782] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.061787] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.061799] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.061804] dwc2 c90c0000.usb: urb_enqueue, urb bb9af015
[  238.061807] dwc2 c90c0000.usb:   Device address: 3
[  238.061811] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.061815] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.061821] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.061825] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.061828] dwc2 c90c0000.usb: HAINT=00001000
[  238.061832] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 12
[  238.061837] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.061841] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Channel Halted--
[  238.061845] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: DMA Channel Halted--
[  238.061849] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Transfer Complete--
[  238.061852] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.061857] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.061861] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 12
[  238.061865] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.061868] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.061872] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.061875] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.061879] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.061885] dwc2 c90c0000.usb: dwc2_host_complete: urb 6510a936 device 3 ep 2-IN status 0 actual 4096
[  238.061890] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.061894] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.061897] dwc2 c90c0000.usb: DMA enabled
[  238.061901] dwc2 c90c0000.usb:   dwc2_release_channel: channel 12, halt_status 2
[  238.061907] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.061910] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.061914] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.061918] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.061923] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.061927] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.061930] dwc2 c90c0000.usb: DMA enabled
[  238.061933] dwc2 c90c0000.usb: desc DMA disabled
[  238.061937] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.061941] dwc2 c90c0000.usb: set HAINTMSK to 00002000
[  238.061945] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.061949] dwc2 c90c0000.usb: set HCCHAR(13) to 00c89200
[  238.061953] dwc2 c90c0000.usb: dwc2_hc_init: Channel 13
[  238.061956] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.061960] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.061963] dwc2 c90c0000.usb: 	 Is In: 1
[  238.061966] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.061970] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.061973] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.061977] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.061981] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.061985] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.061989] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.061992] dwc2 c90c0000.usb: no split
[  238.061997] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(13)
[  238.062000] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 13
[  238.062004] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.062007] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.062011] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.062015] dwc2 c90c0000.usb: Wrote 1fe22000 to HCDMA(13)
[  238.062019] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.062023] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(13)
[  238.062027] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.062031] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.062048] dwc2 c90c0000.usb:   Speed: HIGH
[  238.062053] dwc2 c90c0000.usb:   Max packet size: 512
[  238.062056] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.062061] dwc2 c90c0000.usb:   Transfer buffer: 0128641f, Transfer DMA: 1fe10000
[  238.062065] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.062069] dwc2 c90c0000.usb:   Interval: 0
[  238.062075] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.062079] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.062088] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.062093] dwc2 c90c0000.usb: urb_enqueue, urb 18062ad2
[  238.062096] dwc2 c90c0000.usb:   Device address: 3
[  238.062100] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.062104] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.062108] dwc2 c90c0000.usb:   Speed: HIGH
[  238.062111] dwc2 c90c0000.usb:   Max packet size: 512
[  238.062115] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.062119] dwc2 c90c0000.usb:   Transfer buffer: 9a9c9d40, Transfer DMA: 1faa2000
[  238.062125] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.062129] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.062132] dwc2 c90c0000.usb: HAINT=00002000
[  238.062136] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 13
[  238.062141] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.062145] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Channel Halted--
[  238.062149] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: DMA Channel Halted--
[  238.062153] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Transfer Complete--
[  238.062156] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.062160] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.062165] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 13
[  238.062168] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.062172] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.062175] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.062179] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.062183] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.062189] dwc2 c90c0000.usb: dwc2_host_complete: urb 6eb02129 device 3 ep 2-IN status 0 actual 4096
[  238.062193] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.062197] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.062200] dwc2 c90c0000.usb: DMA enabled
[  238.062205] dwc2 c90c0000.usb:   dwc2_release_channel: channel 13, halt_status 2
[  238.062210] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.062213] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.062216] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.062220] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.062225] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.062229] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.062232] dwc2 c90c0000.usb: DMA enabled
[  238.062235] dwc2 c90c0000.usb: desc DMA disabled
[  238.062239] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.062243] dwc2 c90c0000.usb: set HAINTMSK to 00004000
[  238.062247] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.062251] dwc2 c90c0000.usb: set HCCHAR(14) to 00c89200
[  238.062255] dwc2 c90c0000.usb: dwc2_hc_init: Channel 14
[  238.062258] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.062262] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.062265] dwc2 c90c0000.usb: 	 Is In: 1
[  238.062273] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.062277] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.062280] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.062284] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.062288] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.062291] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.062295] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.062299] dwc2 c90c0000.usb: no split
[  238.062303] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(14)
[  238.062307] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 14
[  238.062310] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.062314] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.062317] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.062321] dwc2 c90c0000.usb: Wrote 1fe8d000 to HCDMA(14)
[  238.062326] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.062330] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(14)
[  238.062334] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.062338] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.062355] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.062359] dwc2 c90c0000.usb:   Interval: 0
[  238.062365] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.062369] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.062378] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.062382] dwc2 c90c0000.usb: urb_enqueue, urb 994c90b3
[  238.062386] dwc2 c90c0000.usb:   Device address: 3
[  238.062390] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.062393] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.062397] dwc2 c90c0000.usb:   Speed: HIGH
[  238.062400] dwc2 c90c0000.usb:   Max packet size: 512
[  238.062404] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.062408] dwc2 c90c0000.usb:   Transfer buffer: e5281bfb, Transfer DMA: 1fb6b000
[  238.062413] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.062420] dwc2 c90c0000.usb:   Interval: 0
[  238.062426] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.062433] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.062436] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.062440] dwc2 c90c0000.usb: HAINT=00004000
[  238.062444] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 14
[  238.062449] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.062453] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Channel Halted--
[  238.062456] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: DMA Channel Halted--
[  238.062461] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Transfer Complete--
[  238.062464] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.062468] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.062473] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 14
[  238.062476] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.062480] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.062483] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.062487] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.062491] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.062497] dwc2 c90c0000.usb: dwc2_host_complete: urb 0e85fd4b device 3 ep 2-IN status 0 actual 4096
[  238.062502] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.062505] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.062509] dwc2 c90c0000.usb: DMA enabled
[  238.062513] dwc2 c90c0000.usb:   dwc2_release_channel: channel 14, halt_status 2
[  238.062518] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.062522] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.062525] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.062529] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.062534] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.062538] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.062541] dwc2 c90c0000.usb: DMA enabled
[  238.062544] dwc2 c90c0000.usb: desc DMA disabled
[  238.062548] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.062552] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[  238.062556] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.062560] dwc2 c90c0000.usb: set HCCHAR(0) to 00c89200
[  238.062564] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[  238.062568] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.062571] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.062574] dwc2 c90c0000.usb: 	 Is In: 1
[  238.062578] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.062581] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.062585] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.062589] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.062592] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.062596] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.062600] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.062603] dwc2 c90c0000.usb: no split
[  238.062607] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(0)
[  238.062611] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[  238.062615] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.062618] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.062622] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.062626] dwc2 c90c0000.usb: Wrote 1fe2e000 to HCDMA(0)
[  238.062629] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.062633] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(0)
[  238.062638] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.062642] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.062657] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.062669] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.062674] dwc2 c90c0000.usb: urb_enqueue, urb 06d5fe84
[  238.062678] dwc2 c90c0000.usb:   Device address: 3
[  238.062681] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.062685] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.062689] dwc2 c90c0000.usb:   Speed: HIGH
[  238.062692] dwc2 c90c0000.usb:   Max packet size: 512
[  238.062696] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.062700] dwc2 c90c0000.usb:   Transfer buffer: 0e12ca11, Transfer DMA: 2d277000
[  238.062705] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.062708] dwc2 c90c0000.usb:   Interval: 0
[  238.062714] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.062718] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.062726] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.062733] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.062736] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.062740] dwc2 c90c0000.usb: HAINT=00000001
[  238.062744] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[  238.062748] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.062752] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Channel Halted--
[  238.062756] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: DMA Channel Halted--
[  238.062761] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Transfer Complete--
[  238.062764] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.062768] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.062773] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 0
[  238.062776] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.062780] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.062783] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.062787] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.062791] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.062797] dwc2 c90c0000.usb: dwc2_host_complete: urb 9ed6427f device 3 ep 2-IN status 0 actual 4096
[  238.062802] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.062806] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.062809] dwc2 c90c0000.usb: DMA enabled
[  238.062813] dwc2 c90c0000.usb:   dwc2_release_channel: channel 0, halt_status 2
[  238.062818] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.062822] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.062825] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.062828] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.062834] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.062837] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.062841] dwc2 c90c0000.usb: DMA enabled
[  238.062844] dwc2 c90c0000.usb: desc DMA disabled
[  238.062848] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.062851] dwc2 c90c0000.usb: set HAINTMSK to 00008000
[  238.062855] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.062860] dwc2 c90c0000.usb: set HCCHAR(15) to 00c89200
[  238.062863] dwc2 c90c0000.usb: dwc2_hc_init: Channel 15
[  238.062867] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.062870] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.062874] dwc2 c90c0000.usb: 	 Is In: 1
[  238.062877] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.062881] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.062884] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.062888] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.062891] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.062895] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.062899] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.062902] dwc2 c90c0000.usb: no split
[  238.062907] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(15)
[  238.062911] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 15
[  238.062914] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.062918] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.062921] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.062925] dwc2 c90c0000.usb: Wrote 1fc80000 to HCDMA(15)
[  238.062929] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.062933] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(15)
[  238.062938] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.062942] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.062957] dwc2 c90c0000.usb: urb_enqueue, urb 698953cf
[  238.062961] dwc2 c90c0000.usb:   Device address: 3
[  238.062965] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.062969] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.062972] dwc2 c90c0000.usb:   Speed: HIGH
[  238.062976] dwc2 c90c0000.usb:   Max packet size: 512
[  238.062980] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.062984] dwc2 c90c0000.usb:   Transfer buffer: 63911724, Transfer DMA: 1fce9000
[  238.062988] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.062992] dwc2 c90c0000.usb:   Interval: 0
[  238.062998] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.063002] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.063012] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.063016] dwc2 c90c0000.usb: urb_enqueue, urb e5d67f36
[  238.063020] dwc2 c90c0000.usb:   Device address: 3
[  238.063024] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.063028] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.063038] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.063042] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.063046] dwc2 c90c0000.usb: HAINT=00008000
[  238.063050] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 15
[  238.063054] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.063058] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Channel Halted--
[  238.063062] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: DMA Channel Halted--
[  238.063066] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Transfer Complete--
[  238.063070] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.063074] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.063078] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 15
[  238.063082] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.063085] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.063089] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.063093] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.063097] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.063103] dwc2 c90c0000.usb: dwc2_host_complete: urb 0cce8d45 device 3 ep 2-IN status 0 actual 4096
[  238.063107] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.063111] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.063114] dwc2 c90c0000.usb: DMA enabled
[  238.063118] dwc2 c90c0000.usb:   dwc2_release_channel: channel 15, halt_status 2
[  238.063124] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.063127] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.063130] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.063134] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.063139] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.063143] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.063146] dwc2 c90c0000.usb: DMA enabled
[  238.063149] dwc2 c90c0000.usb: desc DMA disabled
[  238.063153] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.063157] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[  238.063161] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.063165] dwc2 c90c0000.usb: set HCCHAR(1) to 00c89200
[  238.063169] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[  238.063172] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.063176] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.063179] dwc2 c90c0000.usb: 	 Is In: 1
[  238.063182] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.063186] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.063189] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.063193] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.063197] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.063201] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.063204] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.063208] dwc2 c90c0000.usb: no split
[  238.063212] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(1)
[  238.063216] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[  238.063220] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.063223] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.063227] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.063231] dwc2 c90c0000.usb: Wrote 1fe10000 to HCDMA(1)
[  238.063234] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.063238] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(1)
[  238.063243] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.063247] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.063263] dwc2 c90c0000.usb:   Speed: HIGH
[  238.063267] dwc2 c90c0000.usb:   Max packet size: 512
[  238.063271] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.063275] dwc2 c90c0000.usb:   Transfer buffer: 96b1d490, Transfer DMA: 1fb1a000
[  238.063279] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.063283] dwc2 c90c0000.usb:   Interval: 0
[  238.063288] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.063297] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.063306] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.063311] dwc2 c90c0000.usb: urb_enqueue, urb c60a6a1a
[  238.063314] dwc2 c90c0000.usb:   Device address: 3
[  238.063318] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.063322] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.063325] dwc2 c90c0000.usb:   Speed: HIGH
[  238.063329] dwc2 c90c0000.usb:   Max packet size: 512
[  238.063332] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.063338] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.063342] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.063345] dwc2 c90c0000.usb: HAINT=00000002
[  238.063349] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[  238.063354] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.063358] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[  238.063362] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[  238.063366] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[  238.063369] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.063373] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.063378] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 1
[  238.063381] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.063385] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.063388] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.063392] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.063396] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.063403] dwc2 c90c0000.usb: dwc2_host_complete: urb bb9af015 device 3 ep 2-IN status 0 actual 4096
[  238.063407] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.063410] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.063414] dwc2 c90c0000.usb: DMA enabled
[  238.063418] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 2
[  238.063424] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.063427] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.063430] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.063434] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.063439] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.063443] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.063446] dwc2 c90c0000.usb: DMA enabled
[  238.063449] dwc2 c90c0000.usb: desc DMA disabled
[  238.063453] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.063457] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[  238.063461] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.063465] dwc2 c90c0000.usb: set HCCHAR(2) to 00c89200
[  238.063469] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[  238.063472] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.063475] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.063479] dwc2 c90c0000.usb: 	 Is In: 1
[  238.063482] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.063486] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.063489] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.063493] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.063497] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.063501] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.063504] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.063508] dwc2 c90c0000.usb: no split
[  238.063512] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(2)
[  238.063516] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[  238.063519] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.063523] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.063526] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.063530] dwc2 c90c0000.usb: Wrote 1faa2000 to HCDMA(2)
[  238.063534] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.063538] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(2)
[  238.063543] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.063547] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.063569] dwc2 c90c0000.usb:   Transfer buffer: 30c74ce8, Transfer DMA: 1fbdd000
[  238.063574] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.063577] dwc2 c90c0000.usb:   Interval: 0
[  238.063583] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.063588] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.063597] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.063601] dwc2 c90c0000.usb: urb_enqueue, urb d40f5527
[  238.063605] dwc2 c90c0000.usb:   Device address: 3
[  238.063609] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.063612] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.063616] dwc2 c90c0000.usb:   Speed: HIGH
[  238.063620] dwc2 c90c0000.usb:   Max packet size: 512
[  238.063623] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.063628] dwc2 c90c0000.usb:   Transfer buffer: 2fc26043, Transfer DMA: 1f992000
[  238.063631] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.063635] dwc2 c90c0000.usb:   Interval: 0
[  238.063643] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.063646] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.063650] dwc2 c90c0000.usb: HAINT=00000004
[  238.063654] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[  238.063658] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.063662] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[  238.063666] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[  238.063670] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[  238.063674] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.063678] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.063682] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 2
[  238.063686] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.063689] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.063693] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.063697] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.063700] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.063706] dwc2 c90c0000.usb: dwc2_host_complete: urb 18062ad2 device 3 ep 2-IN status 0 actual 4096
[  238.063711] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.063715] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.063718] dwc2 c90c0000.usb: DMA enabled
[  238.063723] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 2
[  238.063728] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.063732] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.063735] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.063738] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.063743] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.063747] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.063750] dwc2 c90c0000.usb: DMA enabled
[  238.063753] dwc2 c90c0000.usb: desc DMA disabled
[  238.063757] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.063761] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[  238.063765] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.063769] dwc2 c90c0000.usb: set HCCHAR(3) to 00c89200
[  238.063773] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[  238.063776] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.063780] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.063783] dwc2 c90c0000.usb: 	 Is In: 1
[  238.063786] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.063790] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.063793] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.063797] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.063801] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.063810] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.063814] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.063817] dwc2 c90c0000.usb: no split
[  238.063822] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(3)
[  238.063826] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[  238.063829] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.063833] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.063836] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.063841] dwc2 c90c0000.usb: Wrote 1fb6b000 to HCDMA(3)
[  238.063845] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.063849] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(3)
[  238.063853] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.063857] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.063878] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.063883] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.063933] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.063940] dwc2 c90c0000.usb: urb_enqueue, urb 219a56a4
[  238.063944] dwc2 c90c0000.usb:   Device address: 3
[  238.063951] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.063954] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.063958] dwc2 c90c0000.usb: HAINT=00000008
[  238.063962] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[  238.063966] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.063971] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[  238.063974] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[  238.063979] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[  238.063982] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.063987] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.063991] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 3
[  238.063995] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.063998] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.064002] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.064005] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.064009] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.064016] dwc2 c90c0000.usb: dwc2_host_complete: urb 994c90b3 device 3 ep 2-IN status 0 actual 4096
[  238.064021] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.064024] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.064028] dwc2 c90c0000.usb: DMA enabled
[  238.064032] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 2
[  238.064037] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.064041] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.064045] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.064048] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.064054] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.064058] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.064061] dwc2 c90c0000.usb: DMA enabled
[  238.064064] dwc2 c90c0000.usb: desc DMA disabled
[  238.064068] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.064072] dwc2 c90c0000.usb: set HAINTMSK to 00000010
[  238.064076] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.064080] dwc2 c90c0000.usb: set HCCHAR(4) to 00c89200
[  238.064084] dwc2 c90c0000.usb: dwc2_hc_init: Channel 4
[  238.064087] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.064091] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.064094] dwc2 c90c0000.usb: 	 Is In: 1
[  238.064097] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.064101] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.064104] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.064108] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.064112] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.064115] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.064119] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.064123] dwc2 c90c0000.usb: no split
[  238.064127] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(4)
[  238.064131] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 4
[  238.064135] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.064138] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.064142] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.064146] dwc2 c90c0000.usb: Wrote 2d277000 to HCDMA(4)
[  238.064150] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.064154] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(4)
[  238.064158] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.064163] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.064183] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.064187] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.064190] dwc2 c90c0000.usb:   Speed: HIGH
[  238.064194] dwc2 c90c0000.usb:   Max packet size: 512
[  238.064198] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.064203] dwc2 c90c0000.usb:   Transfer buffer: e125dc55, Transfer DMA: 1fbfe000
[  238.064207] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.064210] dwc2 c90c0000.usb:   Interval: 0
[  238.064217] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.064221] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.064231] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.064236] dwc2 c90c0000.usb: urb_enqueue, urb c4da2cad
[  238.064239] dwc2 c90c0000.usb:   Device address: 3
[  238.064243] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.064247] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.064250] dwc2 c90c0000.usb:   Speed: HIGH
[  238.064254] dwc2 c90c0000.usb:   Max packet size: 512
[  238.064257] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.064262] dwc2 c90c0000.usb:   Transfer buffer: 98b41165, Transfer DMA: 1fe0f000
[  238.064269] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.064272] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.064276] dwc2 c90c0000.usb: HAINT=00000010
[  238.064280] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 4
[  238.064285] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.064289] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Channel Halted--
[  238.064293] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: DMA Channel Halted--
[  238.064297] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Transfer Complete--
[  238.064301] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.064305] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.064310] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 4
[  238.064313] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.064317] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.064320] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.064324] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.064328] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.064334] dwc2 c90c0000.usb: dwc2_host_complete: urb 06d5fe84 device 3 ep 2-IN status 0 actual 4096
[  238.064339] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.064342] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.064346] dwc2 c90c0000.usb: DMA enabled
[  238.064350] dwc2 c90c0000.usb:   dwc2_release_channel: channel 4, halt_status 2
[  238.064355] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.064359] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.064362] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.064365] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.064371] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.064375] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.064378] dwc2 c90c0000.usb: DMA enabled
[  238.064381] dwc2 c90c0000.usb: desc DMA disabled
[  238.064385] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.064389] dwc2 c90c0000.usb: set HAINTMSK to 00000040
[  238.064393] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.064397] dwc2 c90c0000.usb: set HCCHAR(6) to 00c89200
[  238.064401] dwc2 c90c0000.usb: dwc2_hc_init: Channel 6
[  238.064404] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.064408] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.064411] dwc2 c90c0000.usb: 	 Is In: 1
[  238.064415] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.064418] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.064422] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.064425] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.064429] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.064433] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.064437] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.064440] dwc2 c90c0000.usb: no split
[  238.064444] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(6)
[  238.064448] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 6
[  238.064452] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.064455] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.064459] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.064463] dwc2 c90c0000.usb: Wrote 1fce9000 to HCDMA(6)
[  238.064467] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.064471] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(6)
[  238.064475] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.064480] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.064498] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.064502] dwc2 c90c0000.usb:   Interval: 0
[  238.064508] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.064513] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.064524] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.064529] dwc2 c90c0000.usb: urb_enqueue, urb 1aa603dd
[  238.064532] dwc2 c90c0000.usb:   Device address: 3
[  238.064536] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.064540] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.064548] dwc2 c90c0000.usb:   Speed: HIGH
[  238.064552] dwc2 c90c0000.usb:   Max packet size: 512
[  238.064556] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.064560] dwc2 c90c0000.usb:   Transfer buffer: 366ba7e1, Transfer DMA: 1f83a000
[  238.064564] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.064570] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.064574] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.064577] dwc2 c90c0000.usb: HAINT=00000040
[  238.064581] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 6
[  238.064586] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.064590] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Channel Halted--
[  238.064594] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: DMA Channel Halted--
[  238.064598] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Transfer Complete--
[  238.064601] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.064605] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.064610] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 6
[  238.064613] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.064617] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.064620] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.064624] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.064628] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.064634] dwc2 c90c0000.usb: dwc2_host_complete: urb 698953cf device 3 ep 2-IN status 0 actual 4096
[  238.064638] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.064642] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.064645] dwc2 c90c0000.usb: DMA enabled
[  238.064650] dwc2 c90c0000.usb:   dwc2_release_channel: channel 6, halt_status 2
[  238.064655] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.064659] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.064662] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.064665] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.064671] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.064674] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.064678] dwc2 c90c0000.usb: DMA enabled
[  238.064681] dwc2 c90c0000.usb: desc DMA disabled
[  238.064685] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.064688] dwc2 c90c0000.usb: set HAINTMSK to 00000020
[  238.064692] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.064696] dwc2 c90c0000.usb: set HCCHAR(5) to 00c89200
[  238.064700] dwc2 c90c0000.usb: dwc2_hc_init: Channel 5
[  238.064704] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.064707] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.064710] dwc2 c90c0000.usb: 	 Is In: 1
[  238.064714] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.064717] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.064721] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.064725] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.064728] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.064732] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.064736] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.064739] dwc2 c90c0000.usb: no split
[  238.064743] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(5)
[  238.064747] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 5
[  238.064751] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.064754] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.064758] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.064762] dwc2 c90c0000.usb: Wrote 1fb1a000 to HCDMA(5)
[  238.064766] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.064770] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(5)
[  238.064774] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.064778] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.064797] dwc2 c90c0000.usb:   Interval: 0
[  238.064804] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.064808] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.064877] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.064881] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.064885] dwc2 c90c0000.usb: HAINT=00000020
[  238.064889] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 5
[  238.064893] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.064898] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Channel Halted--
[  238.064901] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: DMA Channel Halted--
[  238.064906] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Transfer Complete--
[  238.064909] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.064914] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.064918] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 5
[  238.064922] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.064925] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.064929] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.064932] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.064936] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.064943] dwc2 c90c0000.usb: dwc2_host_complete: urb e5d67f36 device 3 ep 2-IN status 0 actual 4096
[  238.064948] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.064952] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.064955] dwc2 c90c0000.usb: DMA enabled
[  238.064960] dwc2 c90c0000.usb:   dwc2_release_channel: channel 5, halt_status 2
[  238.064965] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.064969] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.064972] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.064975] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.064981] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.064985] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.064988] dwc2 c90c0000.usb: DMA enabled
[  238.064992] dwc2 c90c0000.usb: desc DMA disabled
[  238.064995] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.064999] dwc2 c90c0000.usb: set HAINTMSK to 00000080
[  238.065003] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.065007] dwc2 c90c0000.usb: set HCCHAR(7) to 00c89200
[  238.065011] dwc2 c90c0000.usb: dwc2_hc_init: Channel 7
[  238.065014] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.065018] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.065021] dwc2 c90c0000.usb: 	 Is In: 1
[  238.065025] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.065028] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.065032] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.065036] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.065039] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.065043] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.065047] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.065050] dwc2 c90c0000.usb: no split
[  238.065055] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(7)
[  238.065059] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 7
[  238.065062] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.065066] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.065069] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.065074] dwc2 c90c0000.usb: Wrote 1fbdd000 to HCDMA(7)
[  238.065077] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.065082] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(7)
[  238.065086] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.065090] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.065184] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.065188] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.065192] dwc2 c90c0000.usb: HAINT=00000080
[  238.065196] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 7
[  238.065201] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.065205] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Channel Halted--
[  238.065209] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: DMA Channel Halted--
[  238.065214] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Transfer Complete--
[  238.065217] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.065222] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.065226] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 7
[  238.065230] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.065233] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.065237] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.065240] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.065244] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.065251] dwc2 c90c0000.usb: dwc2_host_complete: urb c60a6a1a device 3 ep 2-IN status 0 actual 4096
[  238.065257] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.065260] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.065264] dwc2 c90c0000.usb: DMA enabled
[  238.065268] dwc2 c90c0000.usb:   dwc2_release_channel: channel 7, halt_status 2
[  238.065273] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.065277] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.065280] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.065284] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.065289] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.065293] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.065303] dwc2 c90c0000.usb: DMA enabled
[  238.065306] dwc2 c90c0000.usb: desc DMA disabled
[  238.065309] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.065313] dwc2 c90c0000.usb: set HAINTMSK to 00000100
[  238.065317] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.065321] dwc2 c90c0000.usb: set HCCHAR(8) to 00c89200
[  238.065325] dwc2 c90c0000.usb: dwc2_hc_init: Channel 8
[  238.065328] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.065332] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.065335] dwc2 c90c0000.usb: 	 Is In: 1
[  238.065339] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.065342] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.065346] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.065350] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.065353] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.065357] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.065361] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.065364] dwc2 c90c0000.usb: no split
[  238.065369] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(8)
[  238.065372] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 8
[  238.065376] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.065379] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.065383] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.065387] dwc2 c90c0000.usb: Wrote 1f992000 to HCDMA(8)
[  238.065391] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.065395] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(8)
[  238.065400] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.065404] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.065500] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.065505] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.065509] dwc2 c90c0000.usb: HAINT=00000100
[  238.065513] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 8
[  238.065517] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.065521] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Channel Halted--
[  238.065525] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: DMA Channel Halted--
[  238.065529] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Transfer Complete--
[  238.065533] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.065537] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.065541] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 8
[  238.065545] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.065548] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.065552] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.065555] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.065559] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.065565] dwc2 c90c0000.usb: dwc2_host_complete: urb d40f5527 device 3 ep 2-IN status 0 actual 4096
[  238.065570] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.065574] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.065577] dwc2 c90c0000.usb: DMA enabled
[  238.065581] dwc2 c90c0000.usb:   dwc2_release_channel: channel 8, halt_status 2
[  238.065587] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.065590] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.065594] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.065597] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.065602] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.065606] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.065609] dwc2 c90c0000.usb: DMA enabled
[  238.065613] dwc2 c90c0000.usb: desc DMA disabled
[  238.065616] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.065620] dwc2 c90c0000.usb: set HAINTMSK to 00000200
[  238.065624] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.065629] dwc2 c90c0000.usb: set HCCHAR(9) to 00c89200
[  238.065633] dwc2 c90c0000.usb: dwc2_hc_init: Channel 9
[  238.065636] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.065639] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.065643] dwc2 c90c0000.usb: 	 Is In: 1
[  238.065646] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.065650] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.065653] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.065657] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.065661] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.065665] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.065669] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.065672] dwc2 c90c0000.usb: no split
[  238.065677] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(9)
[  238.065681] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 9
[  238.065684] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.065688] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.065692] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.065696] dwc2 c90c0000.usb: Wrote 1fbfe000 to HCDMA(9)
[  238.065700] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.065704] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(9)
[  238.065708] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.065713] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.065808] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.065813] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.065816] dwc2 c90c0000.usb: HAINT=00000200
[  238.065820] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 9
[  238.065825] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.065829] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Channel Halted--
[  238.065833] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: DMA Channel Halted--
[  238.065837] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Transfer Complete--
[  238.065841] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.065845] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.065849] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 9
[  238.065853] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.065856] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.065860] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.065863] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.065867] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.065873] dwc2 c90c0000.usb: dwc2_host_complete: urb 219a56a4 device 3 ep 2-IN status 0 actual 4096
[  238.065878] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.065882] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.065885] dwc2 c90c0000.usb: DMA enabled
[  238.065889] dwc2 c90c0000.usb:   dwc2_release_channel: channel 9, halt_status 2
[  238.065895] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.065898] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.065901] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.065905] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.065910] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.065914] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.065917] dwc2 c90c0000.usb: DMA enabled
[  238.065920] dwc2 c90c0000.usb: desc DMA disabled
[  238.065924] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.065928] dwc2 c90c0000.usb: set HAINTMSK to 00000400
[  238.065932] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.065936] dwc2 c90c0000.usb: set HCCHAR(10) to 00c89200
[  238.065940] dwc2 c90c0000.usb: dwc2_hc_init: Channel 10
[  238.065943] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.065947] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.065950] dwc2 c90c0000.usb: 	 Is In: 1
[  238.065954] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.065957] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.065960] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.065964] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.065968] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.065971] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.065975] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.065979] dwc2 c90c0000.usb: no split
[  238.065983] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(10)
[  238.065987] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 10
[  238.065990] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.065994] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.065997] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.066001] dwc2 c90c0000.usb: Wrote 1fe0f000 to HCDMA(10)
[  238.066005] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.066009] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(10)
[  238.066013] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.066018] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.066110] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.066115] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.066119] dwc2 c90c0000.usb: HAINT=00000400
[  238.066123] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 10
[  238.066127] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.066131] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Channel Halted--
[  238.066135] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: DMA Channel Halted--
[  238.066139] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Transfer Complete--
[  238.066142] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.066147] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.066151] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 10
[  238.066155] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.066158] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.066162] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.066165] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.066169] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.066176] dwc2 c90c0000.usb: dwc2_host_complete: urb c4da2cad device 3 ep 2-IN status 0 actual 4096
[  238.066181] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.066185] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.066188] dwc2 c90c0000.usb: DMA enabled
[  238.066192] dwc2 c90c0000.usb:   dwc2_release_channel: channel 10, halt_status 2
[  238.066198] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.066201] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.066205] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.066208] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.066214] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.066218] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.066221] dwc2 c90c0000.usb: DMA enabled
[  238.066224] dwc2 c90c0000.usb: desc DMA disabled
[  238.066228] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.066232] dwc2 c90c0000.usb: set HAINTMSK to 00000800
[  238.066236] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.066240] dwc2 c90c0000.usb: set HCCHAR(11) to 00c89200
[  238.066244] dwc2 c90c0000.usb: dwc2_hc_init: Channel 11
[  238.066248] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.066251] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.066254] dwc2 c90c0000.usb: 	 Is In: 1
[  238.066258] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.066261] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.066265] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.066268] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.066272] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.066276] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.066280] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.066283] dwc2 c90c0000.usb: no split
[  238.066287] dwc2 c90c0000.usb: Wrote 00802000 to HCTSIZ(11)
[  238.066291] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 11
[  238.066295] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.066298] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.066302] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.066306] dwc2 c90c0000.usb: Wrote 1f83a000 to HCDMA(11)
[  238.066310] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.066314] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(11)
[  238.066318] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.066322] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.066605] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.066609] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.066613] dwc2 c90c0000.usb: HAINT=00000800
[  238.066617] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 11
[  238.066622] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.066626] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Channel Halted--
[  238.066630] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: DMA Channel Halted--
[  238.066634] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Transfer Complete--
[  238.066637] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.066642] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.066646] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 11
[  238.066650] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.066653] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.066657] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.066660] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.066664] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.066670] dwc2 c90c0000.usb: dwc2_host_complete: urb 1aa603dd device 3 ep 2-IN status 0 actual 8192
[  238.066675] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.066679] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.066682] dwc2 c90c0000.usb: DMA enabled
[  238.066686] dwc2 c90c0000.usb:   dwc2_release_channel: channel 11, halt_status 2
[  238.066691] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.066695] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.066698] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.066702] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.066707] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.066760] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.066766] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.066769] dwc2 c90c0000.usb:   Device address: 3
[  238.066773] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.066777] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.066781] dwc2 c90c0000.usb:   Speed: HIGH
[  238.066785] dwc2 c90c0000.usb:   Max packet size: 512
[  238.066788] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.066798] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.066803] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.066806] dwc2 c90c0000.usb:   Interval: 0
[  238.066813] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.066818] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.066925] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.066930] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.066934] dwc2 c90c0000.usb: DMA enabled
[  238.066937] dwc2 c90c0000.usb: desc DMA disabled
[  238.066941] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.066945] dwc2 c90c0000.usb: set HAINTMSK to 00001000
[  238.066949] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.066953] dwc2 c90c0000.usb: set HCCHAR(12) to 00c89200
[  238.066956] dwc2 c90c0000.usb: dwc2_hc_init: Channel 12
[  238.066960] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.066963] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.066967] dwc2 c90c0000.usb: 	 Is In: 1
[  238.066970] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.066974] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.066977] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.066981] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.066985] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.066989] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.066993] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.066996] dwc2 c90c0000.usb: no split
[  238.067001] dwc2 c90c0000.usb: Wrote 00080200 to HCTSIZ(12)
[  238.067005] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 12
[  238.067008] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.067012] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.067016] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.067020] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(12)
[  238.067024] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.067028] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(12)
[  238.067051] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.067055] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.067058] dwc2 c90c0000.usb: HAINT=00001000
[  238.067063] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 12
[  238.067067] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.067072] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Channel Halted--
[  238.067075] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: DMA Channel Halted--
[  238.067080] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Transfer Complete--
[  238.067084] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.067088] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.067092] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 12
[  238.067096] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.067099] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.067103] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.067107] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.067110] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.067117] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.067122] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.067125] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.067128] dwc2 c90c0000.usb: DMA enabled
[  238.067133] dwc2 c90c0000.usb:   dwc2_release_channel: channel 12, halt_status 2
[  238.067138] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.067142] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.067146] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.067150] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.067155] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.067904] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.067914] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.067927] dwc2 c90c0000.usb:   Device address: 3
[  238.067931] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.067936] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.067939] dwc2 c90c0000.usb:   Speed: HIGH
[  238.067943] dwc2 c90c0000.usb:   Max packet size: 512
[  238.067947] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.067951] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.067956] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.067959] dwc2 c90c0000.usb:   Interval: 0
[  238.067966] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.067971] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.068049] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.068055] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.068058] dwc2 c90c0000.usb: DMA enabled
[  238.068061] dwc2 c90c0000.usb: desc DMA disabled
[  238.068065] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.068069] dwc2 c90c0000.usb: set HAINTMSK to 00002000
[  238.068073] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.068078] dwc2 c90c0000.usb: set HCCHAR(13) to 00c80a00
[  238.068081] dwc2 c90c0000.usb: dwc2_hc_init: Channel 13
[  238.068085] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.068088] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.068092] dwc2 c90c0000.usb: 	 Is In: 0
[  238.068095] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.068098] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.068102] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.068106] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.068110] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.068114] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.068119] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.068122] dwc2 c90c0000.usb: no split
[  238.068127] dwc2 c90c0000.usb: Wrote 4008001f to HCTSIZ(13)
[  238.068131] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 13
[  238.068135] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.068138] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.068142] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.068146] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(13)
[  238.068150] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.068154] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(13)
[  238.068165] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.068169] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.068172] dwc2 c90c0000.usb: HAINT=00002000
[  238.068177] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 13
[  238.068181] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.068186] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Channel Halted--
[  238.068190] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: DMA Channel Halted--
[  238.068194] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Transfer Complete--
[  238.068198] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.068202] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.068207] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 13
[  238.068211] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.068214] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.068218] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.068221] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.068225] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.068232] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.068238] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.068243] dwc2 c90c0000.usb:   dwc2_release_channel: channel 13, halt_status 2
[  238.068248] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.068252] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.068256] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.068261] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.068265] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.068322] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.068328] dwc2 c90c0000.usb: urb_enqueue, urb c60a6a1a
[  238.068332] dwc2 c90c0000.usb:   Device address: 3
[  238.068336] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.068339] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.068343] dwc2 c90c0000.usb:   Speed: HIGH
[  238.068347] dwc2 c90c0000.usb:   Max packet size: 512
[  238.068351] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.068355] dwc2 c90c0000.usb:   Transfer buffer: 952baeca, Transfer DMA: 2d270000
[  238.068360] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.068363] dwc2 c90c0000.usb:   Interval: 0
[  238.068369] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.068374] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.068385] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.068389] dwc2 c90c0000.usb: urb_enqueue, urb d40f5527
[  238.068393] dwc2 c90c0000.usb:   Device address: 3
[  238.068397] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.068401] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.068404] dwc2 c90c0000.usb:   Speed: HIGH
[  238.068407] dwc2 c90c0000.usb:   Max packet size: 512
[  238.068411] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.068415] dwc2 c90c0000.usb:   Transfer buffer: a304fb77, Transfer DMA: 1f8d4000
[  238.068423] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.068427] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.068431] dwc2 c90c0000.usb: DMA enabled
[  238.068434] dwc2 c90c0000.usb: desc DMA disabled
[  238.068438] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.068442] dwc2 c90c0000.usb: set HAINTMSK to 00004000
[  238.068445] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.068450] dwc2 c90c0000.usb: set HCCHAR(14) to 00c89200
[  238.068453] dwc2 c90c0000.usb: dwc2_hc_init: Channel 14
[  238.068457] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.068461] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.068464] dwc2 c90c0000.usb: 	 Is In: 1
[  238.068467] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.068471] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.068474] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.068478] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.068482] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.068486] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.068490] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.068493] dwc2 c90c0000.usb: no split
[  238.068497] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(14)
[  238.068501] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 14
[  238.068505] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.068508] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.068512] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.068516] dwc2 c90c0000.usb: Wrote 2d270000 to HCDMA(14)
[  238.068520] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.068524] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(14)
[  238.068532] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.068535] dwc2 c90c0000.usb:   Interval: 0
[  238.068541] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.068549] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.068561] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.068565] dwc2 c90c0000.usb: urb_enqueue, urb 219a56a4
[  238.068569] dwc2 c90c0000.usb:   Device address: 3
[  238.068573] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.068577] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.068580] dwc2 c90c0000.usb:   Speed: HIGH
[  238.068584] dwc2 c90c0000.usb:   Max packet size: 512
[  238.068587] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.068592] dwc2 c90c0000.usb:   Transfer buffer: de807d3e, Transfer DMA: 1fbd2000
[  238.068596] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.068599] dwc2 c90c0000.usb:   Interval: 0
[  238.068605] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.068609] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.068618] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.068622] dwc2 c90c0000.usb: urb_enqueue, urb c4da2cad
[  238.068626] dwc2 c90c0000.usb:   Device address: 3
[  238.068629] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.068633] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.068637] dwc2 c90c0000.usb:   Speed: HIGH
[  238.068640] dwc2 c90c0000.usb:   Max packet size: 512
[  238.068644] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.068648] dwc2 c90c0000.usb:   Transfer buffer: d8b4e5c2, Transfer DMA: 2e7fc000
[  238.068652] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.068662] dwc2 c90c0000.usb:   Interval: 0
[  238.068672] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.068677] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.068689] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.068694] dwc2 c90c0000.usb: urb_enqueue, urb 1aa603dd
[  238.068697] dwc2 c90c0000.usb:   Device address: 3
[  238.068701] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.068705] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.068708] dwc2 c90c0000.usb:   Speed: HIGH
[  238.068712] dwc2 c90c0000.usb:   Max packet size: 512
[  238.068715] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.068720] dwc2 c90c0000.usb:   Transfer buffer: b473a9fd, Transfer DMA: 2d03a000
[  238.068724] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.068727] dwc2 c90c0000.usb:   Interval: 0
[  238.068733] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.068737] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.068748] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.068752] dwc2 c90c0000.usb: urb_enqueue, urb 9f0be01d
[  238.068756] dwc2 c90c0000.usb:   Device address: 3
[  238.068759] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.068763] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.068767] dwc2 c90c0000.usb:   Speed: HIGH
[  238.068770] dwc2 c90c0000.usb:   Max packet size: 512
[  238.068774] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.068778] dwc2 c90c0000.usb:   Transfer buffer: 37def209, Transfer DMA: 2e19c000
[  238.068782] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.068786] dwc2 c90c0000.usb:   Interval: 0
[  238.068791] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.068800] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.068810] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.068818] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.068822] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.068826] dwc2 c90c0000.usb: HAINT=00004000
[  238.068830] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 14
[  238.068835] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.068840] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Channel Halted--
[  238.068843] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: DMA Channel Halted--
[  238.068848] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Transfer Complete--
[  238.068852] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.068856] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.068860] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 14
[  238.068864] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.068868] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.068871] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.068875] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.068879] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.068885] dwc2 c90c0000.usb: dwc2_host_complete: urb c60a6a1a device 3 ep 2-IN status 0 actual 8192
[  238.068890] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.068893] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.068897] dwc2 c90c0000.usb: DMA enabled
[  238.068901] dwc2 c90c0000.usb:   dwc2_release_channel: channel 14, halt_status 2
[  238.068906] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.068910] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.068914] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.068917] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.068923] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.068927] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.068930] dwc2 c90c0000.usb: DMA enabled
[  238.068933] dwc2 c90c0000.usb: desc DMA disabled
[  238.068937] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.068940] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[  238.068944] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.068949] dwc2 c90c0000.usb: set HCCHAR(0) to 00c89200
[  238.068953] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[  238.068956] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.068959] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.068963] dwc2 c90c0000.usb: 	 Is In: 1
[  238.068967] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.068970] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.068974] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.068977] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.068981] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.068985] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.068989] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.068992] dwc2 c90c0000.usb: no split
[  238.068997] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(0)
[  238.069001] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[  238.069004] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.069008] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.069011] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.069015] dwc2 c90c0000.usb: Wrote 1f8d4000 to HCDMA(0)
[  238.069019] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.069023] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(0)
[  238.069027] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.069032] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.069055] dwc2 c90c0000.usb: urb_enqueue, urb b9fdbbfd
[  238.069060] dwc2 c90c0000.usb:   Device address: 3
[  238.069064] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.069067] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.069071] dwc2 c90c0000.usb:   Speed: HIGH
[  238.069075] dwc2 c90c0000.usb:   Max packet size: 512
[  238.069078] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.069083] dwc2 c90c0000.usb:   Transfer buffer: bb172d8d, Transfer DMA: 1fd00000
[  238.069087] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.069090] dwc2 c90c0000.usb:   Interval: 0
[  238.069096] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.069101] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.069113] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.069118] dwc2 c90c0000.usb: urb_enqueue, urb 64d8cdc0
[  238.069122] dwc2 c90c0000.usb:   Device address: 3
[  238.069125] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.069129] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.069132] dwc2 c90c0000.usb:   Speed: HIGH
[  238.069136] dwc2 c90c0000.usb:   Max packet size: 512
[  238.069140] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.069144] dwc2 c90c0000.usb:   Transfer buffer: 527b64d6, Transfer DMA: 1fe7a000
[  238.069148] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.069152] dwc2 c90c0000.usb:   Interval: 0
[  238.069157] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.069161] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.069176] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.069181] dwc2 c90c0000.usb: urb_enqueue, urb 544633e2
[  238.069184] dwc2 c90c0000.usb:   Device address: 3
[  238.069188] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.069192] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.069195] dwc2 c90c0000.usb:   Speed: HIGH
[  238.069199] dwc2 c90c0000.usb:   Max packet size: 512
[  238.069203] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.069207] dwc2 c90c0000.usb:   Transfer buffer: 289b6671, Transfer DMA: 1fc74000
[  238.069211] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.069215] dwc2 c90c0000.usb:   Interval: 0
[  238.069221] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.069225] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.069236] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.069240] dwc2 c90c0000.usb: urb_enqueue, urb cd91f79f
[  238.069243] dwc2 c90c0000.usb:   Device address: 3
[  238.069247] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.069251] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.069254] dwc2 c90c0000.usb:   Speed: HIGH
[  238.069258] dwc2 c90c0000.usb:   Max packet size: 512
[  238.069262] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.069266] dwc2 c90c0000.usb:   Transfer buffer: dd90b828, Transfer DMA: 1fa68000
[  238.069270] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.069273] dwc2 c90c0000.usb:   Interval: 0
[  238.069279] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.069283] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.069299] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.069303] dwc2 c90c0000.usb: urb_enqueue, urb 67466227
[  238.069309] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.069312] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.069316] dwc2 c90c0000.usb: HAINT=00000001
[  238.069320] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[  238.069324] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.069328] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Channel Halted--
[  238.069332] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: DMA Channel Halted--
[  238.069337] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Transfer Complete--
[  238.069340] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.069344] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.069349] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 0
[  238.069352] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.069356] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.069360] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.069363] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.069367] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.069373] dwc2 c90c0000.usb: dwc2_host_complete: urb d40f5527 device 3 ep 2-IN status 0 actual 8192
[  238.069378] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.069382] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.069385] dwc2 c90c0000.usb: DMA enabled
[  238.069389] dwc2 c90c0000.usb:   dwc2_release_channel: channel 0, halt_status 2
[  238.069394] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.069398] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.069401] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.069404] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.069410] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.069414] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.069417] dwc2 c90c0000.usb: DMA enabled
[  238.069420] dwc2 c90c0000.usb: desc DMA disabled
[  238.069424] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.069428] dwc2 c90c0000.usb: set HAINTMSK to 00008000
[  238.069432] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.069436] dwc2 c90c0000.usb: set HCCHAR(15) to 00c89200
[  238.069440] dwc2 c90c0000.usb: dwc2_hc_init: Channel 15
[  238.069444] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.069447] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.069450] dwc2 c90c0000.usb: 	 Is In: 1
[  238.069454] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.069463] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.069467] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.069470] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.069474] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.069478] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.069482] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.069485] dwc2 c90c0000.usb: no split
[  238.069490] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(15)
[  238.069493] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 15
[  238.069497] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.069500] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.069504] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.069508] dwc2 c90c0000.usb: Wrote 1fbd2000 to HCDMA(15)
[  238.069512] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.069516] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(15)
[  238.069520] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.069525] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.069549] dwc2 c90c0000.usb:   Device address: 3
[  238.069553] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.069557] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.069560] dwc2 c90c0000.usb:   Speed: HIGH
[  238.069564] dwc2 c90c0000.usb:   Max packet size: 512
[  238.069568] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.069573] dwc2 c90c0000.usb:   Transfer buffer: c19e15db, Transfer DMA: 2e732000
[  238.069577] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.069581] dwc2 c90c0000.usb:   Interval: 0
[  238.069587] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.069592] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.069603] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.069607] dwc2 c90c0000.usb: urb_enqueue, urb a7ce381f
[  238.069611] dwc2 c90c0000.usb:   Device address: 3
[  238.069615] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.069619] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.069622] dwc2 c90c0000.usb:   Speed: HIGH
[  238.069625] dwc2 c90c0000.usb:   Max packet size: 512
[  238.069629] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.069634] dwc2 c90c0000.usb:   Transfer buffer: a176563c, Transfer DMA: 1fdb6000
[  238.069638] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.069641] dwc2 c90c0000.usb:   Interval: 0
[  238.069647] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.069651] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.069661] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.069665] dwc2 c90c0000.usb: urb_enqueue, urb 5f70d834
[  238.069673] dwc2 c90c0000.usb:   Device address: 3
[  238.069677] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.069681] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.069684] dwc2 c90c0000.usb:   Speed: HIGH
[  238.069688] dwc2 c90c0000.usb:   Max packet size: 512
[  238.069691] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.069696] dwc2 c90c0000.usb:   Transfer buffer: 72bddd14, Transfer DMA: 1fe24000
[  238.069701] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.069704] dwc2 c90c0000.usb:   Interval: 0
[  238.069709] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.069713] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.069723] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.069728] dwc2 c90c0000.usb: urb_enqueue, urb c4a7e8a9
[  238.069731] dwc2 c90c0000.usb:   Device address: 3
[  238.069735] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.069739] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.069742] dwc2 c90c0000.usb:   Speed: HIGH
[  238.069746] dwc2 c90c0000.usb:   Max packet size: 512
[  238.069749] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.069754] dwc2 c90c0000.usb:   Transfer buffer: b3e395eb, Transfer DMA: 1fbde000
[  238.069758] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.069761] dwc2 c90c0000.usb:   Interval: 0
[  238.069768] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.069772] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.069781] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.069785] dwc2 c90c0000.usb: urb_enqueue, urb f8714879
[  238.069789] dwc2 c90c0000.usb:   Device address: 3
[  238.069797] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.069801] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.069808] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.069811] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.069815] dwc2 c90c0000.usb: HAINT=00008000
[  238.069819] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 15
[  238.069823] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.069827] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Channel Halted--
[  238.069831] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: DMA Channel Halted--
[  238.069835] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Transfer Complete--
[  238.069839] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.069843] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.069848] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 15
[  238.069851] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.069854] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.069858] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.069862] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.069866] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.069872] dwc2 c90c0000.usb: dwc2_host_complete: urb 219a56a4 device 3 ep 2-IN status 0 actual 8192
[  238.069878] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.069881] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.069885] dwc2 c90c0000.usb: DMA enabled
[  238.069889] dwc2 c90c0000.usb:   dwc2_release_channel: channel 15, halt_status 2
[  238.069894] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.069898] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.069901] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.069905] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.069910] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.069914] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.069917] dwc2 c90c0000.usb: DMA enabled
[  238.069920] dwc2 c90c0000.usb: desc DMA disabled
[  238.069924] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.069928] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[  238.069932] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.069936] dwc2 c90c0000.usb: set HCCHAR(1) to 00c89200
[  238.069940] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[  238.069944] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.069947] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.069950] dwc2 c90c0000.usb: 	 Is In: 1
[  238.069954] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.069957] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.069961] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.069965] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.069969] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.069973] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.069977] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.069980] dwc2 c90c0000.usb: no split
[  238.069985] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(1)
[  238.069989] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[  238.069992] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.069996] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.069999] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.070003] dwc2 c90c0000.usb: Wrote 2e7fc000 to HCDMA(1)
[  238.070007] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.070011] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(1)
[  238.070015] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.070020] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.070038] dwc2 c90c0000.usb:   Speed: HIGH
[  238.070046] dwc2 c90c0000.usb:   Max packet size: 512
[  238.070050] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.070054] dwc2 c90c0000.usb:   Transfer buffer: 25e36343, Transfer DMA: 1fbfc000
[  238.070059] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.070062] dwc2 c90c0000.usb:   Interval: 0
[  238.070068] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.070072] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.070288] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.070293] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.070297] dwc2 c90c0000.usb: HAINT=00000002
[  238.070301] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[  238.070305] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.070310] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[  238.070314] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[  238.070318] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[  238.070322] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.070326] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.070331] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 1
[  238.070334] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.070338] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.070342] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.070345] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.070349] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.070356] dwc2 c90c0000.usb: dwc2_host_complete: urb c4da2cad device 3 ep 2-IN status 0 actual 8192
[  238.070361] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.070365] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.070368] dwc2 c90c0000.usb: DMA enabled
[  238.070372] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 2
[  238.070378] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.070381] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.070385] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.070389] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.070394] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.070398] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.070402] dwc2 c90c0000.usb: DMA enabled
[  238.070405] dwc2 c90c0000.usb: desc DMA disabled
[  238.070409] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.070412] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[  238.070417] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.070421] dwc2 c90c0000.usb: set HCCHAR(2) to 00c89200
[  238.070425] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[  238.070428] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.070431] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.070435] dwc2 c90c0000.usb: 	 Is In: 1
[  238.070438] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.070442] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.070445] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.070449] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.070453] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.070457] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.070461] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.070464] dwc2 c90c0000.usb: no split
[  238.070468] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(2)
[  238.070472] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[  238.070476] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.070479] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.070483] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.070487] dwc2 c90c0000.usb: Wrote 2d03a000 to HCDMA(2)
[  238.070490] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.070494] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(2)
[  238.070499] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.070503] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.070786] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.070791] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.070795] dwc2 c90c0000.usb: HAINT=00000004
[  238.070799] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[  238.070803] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.070807] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[  238.070811] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[  238.070815] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[  238.070819] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.070823] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.070827] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 2
[  238.070831] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.070834] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.070838] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.070841] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.070845] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.070851] dwc2 c90c0000.usb: dwc2_host_complete: urb 1aa603dd device 3 ep 2-IN status 0 actual 8192
[  238.070856] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.070860] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.070863] dwc2 c90c0000.usb: DMA enabled
[  238.070868] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 2
[  238.070873] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.070876] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.070880] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.070883] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.070888] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.070892] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.070896] dwc2 c90c0000.usb: DMA enabled
[  238.070899] dwc2 c90c0000.usb: desc DMA disabled
[  238.070902] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.070906] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[  238.070910] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.070914] dwc2 c90c0000.usb: set HCCHAR(3) to 00c89200
[  238.070918] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[  238.070921] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.070925] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.070928] dwc2 c90c0000.usb: 	 Is In: 1
[  238.070931] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.070935] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.070938] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.070942] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.070946] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.070950] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.070953] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.070957] dwc2 c90c0000.usb: no split
[  238.070961] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(3)
[  238.070965] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[  238.070968] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.070972] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.070975] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.070980] dwc2 c90c0000.usb: Wrote 2e19c000 to HCDMA(3)
[  238.070989] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.070993] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(3)
[  238.070997] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.071002] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.071266] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.071270] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.071274] dwc2 c90c0000.usb: HAINT=00000008
[  238.071278] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[  238.071283] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.071287] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[  238.071291] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[  238.071295] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[  238.071298] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.071302] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.071307] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 3
[  238.071310] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.071314] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.071317] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.071321] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.071325] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.071331] dwc2 c90c0000.usb: dwc2_host_complete: urb 9f0be01d device 3 ep 2-IN status 0 actual 8192
[  238.071336] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.071340] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.071343] dwc2 c90c0000.usb: DMA enabled
[  238.071347] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 2
[  238.071352] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.071356] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.071359] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.071363] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.071368] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.071372] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.071375] dwc2 c90c0000.usb: DMA enabled
[  238.071378] dwc2 c90c0000.usb: desc DMA disabled
[  238.071382] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.071386] dwc2 c90c0000.usb: set HAINTMSK to 00000010
[  238.071390] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.071394] dwc2 c90c0000.usb: set HCCHAR(4) to 00c89200
[  238.071398] dwc2 c90c0000.usb: dwc2_hc_init: Channel 4
[  238.071401] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.071405] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.071408] dwc2 c90c0000.usb: 	 Is In: 1
[  238.071411] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.071415] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.071418] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.071422] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.071426] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.071430] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.071434] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.071438] dwc2 c90c0000.usb: no split
[  238.071442] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(4)
[  238.071446] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 4
[  238.071449] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.071453] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.071456] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.071460] dwc2 c90c0000.usb: Wrote 1fd00000 to HCDMA(4)
[  238.071464] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.071468] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(4)
[  238.071472] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.071477] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.071760] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.071764] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.071768] dwc2 c90c0000.usb: HAINT=00000010
[  238.071772] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 4
[  238.071777] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.071781] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Channel Halted--
[  238.071785] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: DMA Channel Halted--
[  238.071789] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Transfer Complete--
[  238.071792] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.071796] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.071801] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 4
[  238.071804] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.071808] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.071811] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.071815] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.071819] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.071825] dwc2 c90c0000.usb: dwc2_host_complete: urb b9fdbbfd device 3 ep 2-IN status 0 actual 8192
[  238.071830] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.071834] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.071837] dwc2 c90c0000.usb: DMA enabled
[  238.071841] dwc2 c90c0000.usb:   dwc2_release_channel: channel 4, halt_status 2
[  238.071847] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.071850] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.071854] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.071857] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.071863] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.071866] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.071870] dwc2 c90c0000.usb: DMA enabled
[  238.071873] dwc2 c90c0000.usb: desc DMA disabled
[  238.071876] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.071880] dwc2 c90c0000.usb: set HAINTMSK to 00000040
[  238.071884] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.071888] dwc2 c90c0000.usb: set HCCHAR(6) to 00c89200
[  238.071892] dwc2 c90c0000.usb: dwc2_hc_init: Channel 6
[  238.071895] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.071899] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.071902] dwc2 c90c0000.usb: 	 Is In: 1
[  238.071906] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.071909] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.071913] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.071916] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.071920] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.071924] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.071927] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.071931] dwc2 c90c0000.usb: no split
[  238.071935] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(6)
[  238.071939] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 6
[  238.071943] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.071946] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.071950] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.071954] dwc2 c90c0000.usb: Wrote 1fe7a000 to HCDMA(6)
[  238.071958] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.071962] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(6)
[  238.071966] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.071970] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.072235] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.072239] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.072243] dwc2 c90c0000.usb: HAINT=00000040
[  238.072247] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 6
[  238.072251] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.072255] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Channel Halted--
[  238.072259] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: DMA Channel Halted--
[  238.072263] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Transfer Complete--
[  238.072267] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.072271] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.072275] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 6
[  238.072279] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.072282] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.072286] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.072289] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.072293] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.072299] dwc2 c90c0000.usb: dwc2_host_complete: urb 64d8cdc0 device 3 ep 2-IN status 0 actual 8192
[  238.072304] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.072308] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.072311] dwc2 c90c0000.usb: DMA enabled
[  238.072315] dwc2 c90c0000.usb:   dwc2_release_channel: channel 6, halt_status 2
[  238.072320] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.072324] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.072327] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.072331] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.072336] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.072340] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.072343] dwc2 c90c0000.usb: DMA enabled
[  238.072346] dwc2 c90c0000.usb: desc DMA disabled
[  238.072350] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.072354] dwc2 c90c0000.usb: set HAINTMSK to 00000020
[  238.072358] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.072362] dwc2 c90c0000.usb: set HCCHAR(5) to 00c89200
[  238.072366] dwc2 c90c0000.usb: dwc2_hc_init: Channel 5
[  238.072369] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.072373] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.072376] dwc2 c90c0000.usb: 	 Is In: 1
[  238.072380] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.072383] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.072386] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.072390] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.072394] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.072398] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.072401] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.072405] dwc2 c90c0000.usb: no split
[  238.072409] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(5)
[  238.072413] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 5
[  238.072417] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.072421] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.072424] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.072428] dwc2 c90c0000.usb: Wrote 1fc74000 to HCDMA(5)
[  238.072432] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.072436] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(5)
[  238.072441] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.072445] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.072728] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.072734] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.072738] dwc2 c90c0000.usb: HAINT=00000020
[  238.072742] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 5
[  238.072746] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.072751] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Channel Halted--
[  238.072755] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: DMA Channel Halted--
[  238.072759] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Transfer Complete--
[  238.072763] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.072767] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.072772] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 5
[  238.072775] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.072779] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.072782] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.072786] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.072790] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.072796] dwc2 c90c0000.usb: dwc2_host_complete: urb 544633e2 device 3 ep 2-IN status 0 actual 8192
[  238.072802] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.072805] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.072809] dwc2 c90c0000.usb: DMA enabled
[  238.072813] dwc2 c90c0000.usb:   dwc2_release_channel: channel 5, halt_status 2
[  238.072818] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.072822] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.072826] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.072829] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.072835] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.072839] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.072842] dwc2 c90c0000.usb: DMA enabled
[  238.072845] dwc2 c90c0000.usb: desc DMA disabled
[  238.072849] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.072853] dwc2 c90c0000.usb: set HAINTMSK to 00000080
[  238.072857] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.072861] dwc2 c90c0000.usb: set HCCHAR(7) to 00c89200
[  238.072865] dwc2 c90c0000.usb: dwc2_hc_init: Channel 7
[  238.072868] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.072872] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.072875] dwc2 c90c0000.usb: 	 Is In: 1
[  238.072878] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.072882] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.072885] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.072889] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.072893] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.072897] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.072900] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.072904] dwc2 c90c0000.usb: no split
[  238.072908] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(7)
[  238.072912] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 7
[  238.072915] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.072919] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.072923] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.072927] dwc2 c90c0000.usb: Wrote 1fa68000 to HCDMA(7)
[  238.072931] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.072935] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(7)
[  238.072939] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.072943] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.073209] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.073213] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.073217] dwc2 c90c0000.usb: HAINT=00000080
[  238.073221] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 7
[  238.073226] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.073230] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Channel Halted--
[  238.073234] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: DMA Channel Halted--
[  238.073238] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Transfer Complete--
[  238.073241] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.073246] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.073250] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 7
[  238.073254] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.073257] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.073261] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.073265] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.073268] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.073275] dwc2 c90c0000.usb: dwc2_host_complete: urb cd91f79f device 3 ep 2-IN status 0 actual 8192
[  238.073280] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.073284] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.073287] dwc2 c90c0000.usb: DMA enabled
[  238.073292] dwc2 c90c0000.usb:   dwc2_release_channel: channel 7, halt_status 2
[  238.073297] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.073301] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.073304] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.073308] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.073313] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.073317] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.073321] dwc2 c90c0000.usb: DMA enabled
[  238.073324] dwc2 c90c0000.usb: desc DMA disabled
[  238.073328] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.073332] dwc2 c90c0000.usb: set HAINTMSK to 00000100
[  238.073335] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.073340] dwc2 c90c0000.usb: set HCCHAR(8) to 00c89200
[  238.073344] dwc2 c90c0000.usb: dwc2_hc_init: Channel 8
[  238.073347] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.073350] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.073354] dwc2 c90c0000.usb: 	 Is In: 1
[  238.073357] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.073361] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.073364] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.073368] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.073372] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.073376] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.073379] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.073383] dwc2 c90c0000.usb: no split
[  238.073387] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(8)
[  238.073391] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 8
[  238.073394] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.073398] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.073401] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.073405] dwc2 c90c0000.usb: Wrote 2e732000 to HCDMA(8)
[  238.073409] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.073413] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(8)
[  238.073418] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.073423] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.073710] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.073715] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.073718] dwc2 c90c0000.usb: HAINT=00000100
[  238.073722] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 8
[  238.073727] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.073731] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Channel Halted--
[  238.073735] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: DMA Channel Halted--
[  238.073739] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Transfer Complete--
[  238.073743] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.073747] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.073752] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 8
[  238.073755] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.073759] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.073762] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.073766] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.073770] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.073776] dwc2 c90c0000.usb: dwc2_host_complete: urb 67466227 device 3 ep 2-IN status 0 actual 8192
[  238.073781] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.073784] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.073787] dwc2 c90c0000.usb: DMA enabled
[  238.073792] dwc2 c90c0000.usb:   dwc2_release_channel: channel 8, halt_status 2
[  238.073797] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.073801] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.073804] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.073808] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.073813] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.073817] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.073820] dwc2 c90c0000.usb: DMA enabled
[  238.073824] dwc2 c90c0000.usb: desc DMA disabled
[  238.073827] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.073831] dwc2 c90c0000.usb: set HAINTMSK to 00000200
[  238.073835] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.073839] dwc2 c90c0000.usb: set HCCHAR(9) to 00c89200
[  238.073843] dwc2 c90c0000.usb: dwc2_hc_init: Channel 9
[  238.073846] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.073850] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.073853] dwc2 c90c0000.usb: 	 Is In: 1
[  238.073856] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.073860] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.073863] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.073867] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.073871] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.073874] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.073878] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.073881] dwc2 c90c0000.usb: no split
[  238.073886] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(9)
[  238.073890] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 9
[  238.073893] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.073897] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.073900] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.073905] dwc2 c90c0000.usb: Wrote 1fdb6000 to HCDMA(9)
[  238.073909] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.073914] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(9)
[  238.073918] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.073922] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.074197] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.074202] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.074206] dwc2 c90c0000.usb: HAINT=00000200
[  238.074211] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 9
[  238.074215] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.074219] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Channel Halted--
[  238.074223] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: DMA Channel Halted--
[  238.074228] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Transfer Complete--
[  238.074231] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.074236] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.074240] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 9
[  238.074244] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.074247] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.074251] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.074255] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.074258] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.074265] dwc2 c90c0000.usb: dwc2_host_complete: urb a7ce381f device 3 ep 2-IN status 0 actual 8192
[  238.074272] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.074276] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.074279] dwc2 c90c0000.usb: DMA enabled
[  238.074284] dwc2 c90c0000.usb:   dwc2_release_channel: channel 9, halt_status 2
[  238.074289] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.074293] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.074297] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.074300] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.074306] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.074310] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.074313] dwc2 c90c0000.usb: DMA enabled
[  238.074317] dwc2 c90c0000.usb: desc DMA disabled
[  238.074320] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.074324] dwc2 c90c0000.usb: set HAINTMSK to 00000400
[  238.074328] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.074333] dwc2 c90c0000.usb: set HCCHAR(10) to 00c89200
[  238.074336] dwc2 c90c0000.usb: dwc2_hc_init: Channel 10
[  238.074340] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.074343] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.074347] dwc2 c90c0000.usb: 	 Is In: 1
[  238.074350] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.074353] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.074357] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.074361] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.074365] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.074369] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.074373] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.074376] dwc2 c90c0000.usb: no split
[  238.074381] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(10)
[  238.074385] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 10
[  238.074389] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.074392] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.074395] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.074400] dwc2 c90c0000.usb: Wrote 1fe24000 to HCDMA(10)
[  238.074403] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.074408] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(10)
[  238.074412] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.074417] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.074711] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.074716] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.074720] dwc2 c90c0000.usb: HAINT=00000400
[  238.074724] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 10
[  238.074728] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.074733] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Channel Halted--
[  238.074737] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: DMA Channel Halted--
[  238.074741] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Transfer Complete--
[  238.074745] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.074749] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.074754] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 10
[  238.074757] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.074761] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.074764] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.074768] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.074772] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.074778] dwc2 c90c0000.usb: dwc2_host_complete: urb 5f70d834 device 3 ep 2-IN status 0 actual 8192
[  238.074783] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.074787] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.074790] dwc2 c90c0000.usb: DMA enabled
[  238.074794] dwc2 c90c0000.usb:   dwc2_release_channel: channel 10, halt_status 2
[  238.074799] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.074803] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.074806] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.074810] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.074815] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.074819] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.074823] dwc2 c90c0000.usb: DMA enabled
[  238.074826] dwc2 c90c0000.usb: desc DMA disabled
[  238.074830] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.074833] dwc2 c90c0000.usb: set HAINTMSK to 00000800
[  238.074837] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.074842] dwc2 c90c0000.usb: set HCCHAR(11) to 00c89200
[  238.074845] dwc2 c90c0000.usb: dwc2_hc_init: Channel 11
[  238.074849] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.074852] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.074856] dwc2 c90c0000.usb: 	 Is In: 1
[  238.074859] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.074863] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.074866] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.074870] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.074874] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.074878] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.074881] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.074884] dwc2 c90c0000.usb: no split
[  238.074889] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(11)
[  238.074892] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 11
[  238.074896] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.074900] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.074903] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.074907] dwc2 c90c0000.usb: Wrote 1fbde000 to HCDMA(11)
[  238.074911] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.074915] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(11)
[  238.074919] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.074923] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.075193] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.075197] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.075201] dwc2 c90c0000.usb: HAINT=00000800
[  238.075205] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 11
[  238.075215] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.075219] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Channel Halted--
[  238.075223] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: DMA Channel Halted--
[  238.075227] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Transfer Complete--
[  238.075231] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.075235] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.075240] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 11
[  238.075243] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.075247] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.075250] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.075254] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.075258] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.075264] dwc2 c90c0000.usb: dwc2_host_complete: urb c4a7e8a9 device 3 ep 2-IN status 0 actual 8192
[  238.075269] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.075273] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.075276] dwc2 c90c0000.usb: DMA enabled
[  238.075280] dwc2 c90c0000.usb:   dwc2_release_channel: channel 11, halt_status 2
[  238.075286] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.075289] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.075293] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.075296] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.075301] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.075305] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.075308] dwc2 c90c0000.usb: DMA enabled
[  238.075312] dwc2 c90c0000.usb: desc DMA disabled
[  238.075315] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.075319] dwc2 c90c0000.usb: set HAINTMSK to 00001000
[  238.075323] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.075328] dwc2 c90c0000.usb: set HCCHAR(12) to 00c89200
[  238.075331] dwc2 c90c0000.usb: dwc2_hc_init: Channel 12
[  238.075335] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.075338] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.075342] dwc2 c90c0000.usb: 	 Is In: 1
[  238.075345] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.075349] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.075352] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.075356] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.075359] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.075363] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.075367] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.075370] dwc2 c90c0000.usb: no split
[  238.075375] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(12)
[  238.075379] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 12
[  238.075382] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.075386] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.075389] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.075393] dwc2 c90c0000.usb: Wrote 1fbfc000 to HCDMA(12)
[  238.075397] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.075401] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(12)
[  238.075405] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.075410] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.075694] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.075698] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.075702] dwc2 c90c0000.usb: HAINT=00001000
[  238.075706] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 12
[  238.075711] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.075715] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Channel Halted--
[  238.075719] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: DMA Channel Halted--
[  238.075723] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Transfer Complete--
[  238.075726] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.075731] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.075735] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 12
[  238.075738] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.075742] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.075745] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.075749] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.075753] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.075759] dwc2 c90c0000.usb: dwc2_host_complete: urb f8714879 device 3 ep 2-IN status 0 actual 8192
[  238.075764] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.075768] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.075771] dwc2 c90c0000.usb: DMA enabled
[  238.075775] dwc2 c90c0000.usb:   dwc2_release_channel: channel 12, halt_status 2
[  238.075780] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.075784] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.075787] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.075791] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.075796] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.075851] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.075857] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.075861] dwc2 c90c0000.usb:   Device address: 3
[  238.075865] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.075869] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.075873] dwc2 c90c0000.usb:   Speed: HIGH
[  238.075877] dwc2 c90c0000.usb:   Max packet size: 512
[  238.075881] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.075885] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.075890] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.075893] dwc2 c90c0000.usb:   Interval: 0
[  238.075900] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.075905] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.075926] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.075932] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.075935] dwc2 c90c0000.usb: DMA enabled
[  238.075939] dwc2 c90c0000.usb: desc DMA disabled
[  238.075943] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.075947] dwc2 c90c0000.usb: set HAINTMSK to 00002000
[  238.075951] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.075955] dwc2 c90c0000.usb: set HCCHAR(13) to 00c89200
[  238.075959] dwc2 c90c0000.usb: dwc2_hc_init: Channel 13
[  238.075969] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.075973] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.075976] dwc2 c90c0000.usb: 	 Is In: 1
[  238.075980] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.075983] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.075987] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.075991] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.075995] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.075998] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.076002] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.076006] dwc2 c90c0000.usb: no split
[  238.076010] dwc2 c90c0000.usb: Wrote 40080200 to HCTSIZ(13)
[  238.076014] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 13
[  238.076018] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.076021] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.076025] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.076030] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(13)
[  238.076033] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.076037] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(13)
[  238.076048] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000008
[  238.076052] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.076056] dwc2 c90c0000.usb: HAINT=00002000
[  238.076060] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 13
[  238.076064] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.076069] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Channel Halted--
[  238.076073] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: DMA Channel Halted--
[  238.076077] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Transfer Complete--
[  238.076081] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.076086] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.076090] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 13
[  238.076094] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.076097] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.076101] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.076104] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.076108] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.076114] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.076120] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.076123] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.076126] dwc2 c90c0000.usb: DMA enabled
[  238.076131] dwc2 c90c0000.usb:   dwc2_release_channel: channel 13, halt_status 2
[  238.076137] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.076140] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.076144] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.076148] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.076153] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.076264] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.076271] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.076276] dwc2 c90c0000.usb:   Device address: 3
[  238.076280] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.076284] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.076287] dwc2 c90c0000.usb:   Speed: HIGH
[  238.076297] dwc2 c90c0000.usb:   Max packet size: 512
[  238.076301] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.076306] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.076310] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.076314] dwc2 c90c0000.usb:   Interval: 0
[  238.076320] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.076325] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.076423] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.076427] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.076431] dwc2 c90c0000.usb: DMA enabled
[  238.076434] dwc2 c90c0000.usb: desc DMA disabled
[  238.076438] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.076442] dwc2 c90c0000.usb: set HAINTMSK to 00004000
[  238.076445] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.076450] dwc2 c90c0000.usb: set HCCHAR(14) to 00c80a00
[  238.076454] dwc2 c90c0000.usb: dwc2_hc_init: Channel 14
[  238.076457] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.076460] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.076464] dwc2 c90c0000.usb: 	 Is In: 0
[  238.076467] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.076471] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.076474] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.076479] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.076483] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.076486] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.076490] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.076494] dwc2 c90c0000.usb: no split
[  238.076498] dwc2 c90c0000.usb: Wrote 0008001f to HCTSIZ(14)
[  238.076502] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 14
[  238.076505] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.076509] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.076512] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.076516] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(14)
[  238.076520] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.076524] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(14)
[  238.076534] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.076538] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.076542] dwc2 c90c0000.usb: HAINT=00004000
[  238.076546] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 14
[  238.076550] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.076554] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Channel Halted--
[  238.076558] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: DMA Channel Halted--
[  238.076563] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Transfer Complete--
[  238.076566] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.076571] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.076576] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 14
[  238.076579] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.076583] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.076586] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.076590] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.076593] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.076600] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.076605] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.076610] dwc2 c90c0000.usb:   dwc2_release_channel: channel 14, halt_status 2
[  238.076616] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.076619] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.076623] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.076627] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.076631] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.076665] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.076675] dwc2 c90c0000.usb: urb_enqueue, urb 64d8cdc0
[  238.076679] dwc2 c90c0000.usb:   Device address: 3
[  238.076683] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.076687] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.076690] dwc2 c90c0000.usb:   Speed: HIGH
[  238.076694] dwc2 c90c0000.usb:   Max packet size: 512
[  238.076698] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.076703] dwc2 c90c0000.usb:   Transfer buffer: 1e7afd17, Transfer DMA: 2e262000
[  238.076707] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.076711] dwc2 c90c0000.usb:   Interval: 0
[  238.076716] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.076721] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.076798] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.076803] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.076806] dwc2 c90c0000.usb: DMA enabled
[  238.076809] dwc2 c90c0000.usb: desc DMA disabled
[  238.076813] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.076817] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[  238.076821] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.076825] dwc2 c90c0000.usb: set HCCHAR(0) to 00c89200
[  238.076829] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[  238.076833] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.076836] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.076839] dwc2 c90c0000.usb: 	 Is In: 1
[  238.076843] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.076846] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.076850] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.076854] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.076858] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.076862] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.076865] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.076869] dwc2 c90c0000.usb: no split
[  238.076873] dwc2 c90c0000.usb: Wrote 00802000 to HCTSIZ(0)
[  238.076877] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[  238.076880] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.076884] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.076887] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.076892] dwc2 c90c0000.usb: Wrote 2e262000 to HCDMA(0)
[  238.076895] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.076900] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(0)
[  238.077184] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.077188] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.077191] dwc2 c90c0000.usb: HAINT=00000001
[  238.077196] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[  238.077200] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.077205] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Channel Halted--
[  238.077209] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: DMA Channel Halted--
[  238.077213] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Transfer Complete--
[  238.077216] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.077221] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.077225] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 0
[  238.077229] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.077232] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.077236] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.077240] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.077243] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.077250] dwc2 c90c0000.usb: dwc2_host_complete: urb 64d8cdc0 device 3 ep 2-IN status 0 actual 8192
[  238.077255] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.077259] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.077262] dwc2 c90c0000.usb: DMA enabled
[  238.077266] dwc2 c90c0000.usb:   dwc2_release_channel: channel 0, halt_status 2
[  238.077272] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.077275] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.077279] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.077283] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.077287] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.077320] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.077326] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.077330] dwc2 c90c0000.usb:   Device address: 3
[  238.077334] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.077337] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.077341] dwc2 c90c0000.usb:   Speed: HIGH
[  238.077345] dwc2 c90c0000.usb:   Max packet size: 512
[  238.077348] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.077353] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.077357] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.077360] dwc2 c90c0000.usb:   Interval: 0
[  238.077366] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.077371] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.077423] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.077428] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.077431] dwc2 c90c0000.usb: DMA enabled
[  238.077435] dwc2 c90c0000.usb: desc DMA disabled
[  238.077439] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.077442] dwc2 c90c0000.usb: set HAINTMSK to 00008000
[  238.077446] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.077451] dwc2 c90c0000.usb: set HCCHAR(15) to 00c89200
[  238.077454] dwc2 c90c0000.usb: dwc2_hc_init: Channel 15
[  238.077458] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.077461] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.077465] dwc2 c90c0000.usb: 	 Is In: 1
[  238.077468] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.077472] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.077475] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.077479] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.077483] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.077486] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.077490] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.077493] dwc2 c90c0000.usb: no split
[  238.077498] dwc2 c90c0000.usb: Wrote 00080200 to HCTSIZ(15)
[  238.077502] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 15
[  238.077505] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.077508] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.077512] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.077517] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(15)
[  238.077520] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.077525] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(15)
[  238.077534] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.077538] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.077548] dwc2 c90c0000.usb: HAINT=00008000
[  238.077552] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 15
[  238.077557] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.077561] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Channel Halted--
[  238.077564] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: DMA Channel Halted--
[  238.077568] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Transfer Complete--
[  238.077572] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.077576] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.077581] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 15
[  238.077584] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.077588] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.077591] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.077595] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.077599] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.077605] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.077610] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.077613] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.077616] dwc2 c90c0000.usb: DMA enabled
[  238.077621] dwc2 c90c0000.usb:   dwc2_release_channel: channel 15, halt_status 2
[  238.077626] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.077630] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.077633] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.077638] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.077642] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.078237] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.078248] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.078252] dwc2 c90c0000.usb:   Device address: 3
[  238.078256] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.078261] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.078264] dwc2 c90c0000.usb:   Speed: HIGH
[  238.078268] dwc2 c90c0000.usb:   Max packet size: 512
[  238.078272] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.078276] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.078281] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.078284] dwc2 c90c0000.usb:   Interval: 0
[  238.078291] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.078306] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.078427] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.078432] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.078436] dwc2 c90c0000.usb: DMA enabled
[  238.078439] dwc2 c90c0000.usb: desc DMA disabled
[  238.078443] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.078447] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[  238.078451] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.078455] dwc2 c90c0000.usb: set HCCHAR(1) to 00c80a00
[  238.078459] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[  238.078462] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.078466] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.078469] dwc2 c90c0000.usb: 	 Is In: 0
[  238.078473] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.078476] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.078480] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.078484] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.078487] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.078491] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.078496] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.078499] dwc2 c90c0000.usb: no split
[  238.078504] dwc2 c90c0000.usb: Wrote 4008001f to HCTSIZ(1)
[  238.078508] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[  238.078511] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.078515] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.078518] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.078523] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(1)
[  238.078527] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.078531] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(1)
[  238.078541] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.078552] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.078555] dwc2 c90c0000.usb: HAINT=00000002
[  238.078560] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[  238.078564] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.078569] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[  238.078573] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[  238.078578] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[  238.078581] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.078586] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.078591] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 1
[  238.078595] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.078598] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.078602] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.078605] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.078609] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.078616] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.078621] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.078626] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 2
[  238.078632] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.078636] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.078639] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.078644] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.078649] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.078698] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.078705] dwc2 c90c0000.usb: urb_enqueue, urb 64d8cdc0
[  238.078708] dwc2 c90c0000.usb:   Device address: 3
[  238.078712] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.078716] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.078720] dwc2 c90c0000.usb:   Speed: HIGH
[  238.078723] dwc2 c90c0000.usb:   Max packet size: 512
[  238.078727] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.078732] dwc2 c90c0000.usb:   Transfer buffer: e69e1bd8, Transfer DMA: 1fa96000
[  238.078737] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.078741] dwc2 c90c0000.usb:   Interval: 0
[  238.078746] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.078752] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.078762] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.078767] dwc2 c90c0000.usb: urb_enqueue, urb 544633e2
[  238.078770] dwc2 c90c0000.usb:   Device address: 3
[  238.078774] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.078778] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.078781] dwc2 c90c0000.usb:   Speed: HIGH
[  238.078785] dwc2 c90c0000.usb:   Max packet size: 512
[  238.078788] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.078796] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.078801] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.078804] dwc2 c90c0000.usb: DMA enabled
[  238.078807] dwc2 c90c0000.usb: desc DMA disabled
[  238.078811] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.078815] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[  238.078818] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.078823] dwc2 c90c0000.usb: set HCCHAR(2) to 00c89200
[  238.078826] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[  238.078830] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.078833] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.078837] dwc2 c90c0000.usb: 	 Is In: 1
[  238.078840] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.078844] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.078848] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.078851] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.078856] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.078859] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.078864] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.078867] dwc2 c90c0000.usb: no split
[  238.078872] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(2)
[  238.078875] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[  238.078879] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.078883] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.078886] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.078890] dwc2 c90c0000.usb: Wrote 1fa96000 to HCDMA(2)
[  238.078894] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.078898] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(2)
[  238.078906] dwc2 c90c0000.usb:   Transfer buffer: 9a47c217, Transfer DMA: 1fb18000
[  238.078910] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.078914] dwc2 c90c0000.usb:   Interval: 0
[  238.078924] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.078929] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.078940] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.078944] dwc2 c90c0000.usb: urb_enqueue, urb cd91f79f
[  238.078948] dwc2 c90c0000.usb:   Device address: 3
[  238.078952] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.078955] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.078959] dwc2 c90c0000.usb:   Speed: HIGH
[  238.078962] dwc2 c90c0000.usb:   Max packet size: 512
[  238.078966] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.078970] dwc2 c90c0000.usb:   Transfer buffer: 9e65b5c3, Transfer DMA: 2d262000
[  238.078975] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.078978] dwc2 c90c0000.usb:   Interval: 0
[  238.078984] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.078988] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.079001] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.079005] dwc2 c90c0000.usb: urb_enqueue, urb 67466227
[  238.079008] dwc2 c90c0000.usb:   Device address: 3
[  238.079012] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.079016] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.079019] dwc2 c90c0000.usb:   Speed: HIGH
[  238.079023] dwc2 c90c0000.usb:   Max packet size: 512
[  238.079027] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.079031] dwc2 c90c0000.usb:   Transfer buffer: 531751a4, Transfer DMA: 1fcfa000
[  238.079035] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.079039] dwc2 c90c0000.usb:   Interval: 0
[  238.079049] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.079053] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.079064] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.079069] dwc2 c90c0000.usb: urb_enqueue, urb a7ce381f
[  238.079073] dwc2 c90c0000.usb:   Device address: 3
[  238.079076] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.079080] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.079083] dwc2 c90c0000.usb:   Speed: HIGH
[  238.079087] dwc2 c90c0000.usb:   Max packet size: 512
[  238.079091] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.079095] dwc2 c90c0000.usb:   Transfer buffer: e4c7e99a, Transfer DMA: 2d274000
[  238.079099] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.079103] dwc2 c90c0000.usb:   Interval: 0
[  238.079108] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.079112] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.079121] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.079125] dwc2 c90c0000.usb: urb_enqueue, urb 5f70d834
[  238.079129] dwc2 c90c0000.usb:   Device address: 3
[  238.079133] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.079136] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.079140] dwc2 c90c0000.usb:   Speed: HIGH
[  238.079143] dwc2 c90c0000.usb:   Max packet size: 512
[  238.079147] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.079151] dwc2 c90c0000.usb:   Transfer buffer: 431cabea, Transfer DMA: 1fac6000
[  238.079155] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.079159] dwc2 c90c0000.usb:   Interval: 0
[  238.079164] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.079173] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.079183] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.079188] dwc2 c90c0000.usb: urb_enqueue, urb c4a7e8a9
[  238.079193] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.079198] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.079201] dwc2 c90c0000.usb: HAINT=00000004
[  238.079205] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[  238.079210] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.079214] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[  238.079218] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[  238.079223] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[  238.079226] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.079231] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.079235] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 2
[  238.079239] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.079242] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.079246] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.079249] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.079253] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.079260] dwc2 c90c0000.usb: dwc2_host_complete: urb 64d8cdc0 device 3 ep 2-IN status 0 actual 8192
[  238.079267] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.079271] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.079274] dwc2 c90c0000.usb: DMA enabled
[  238.079279] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 2
[  238.079285] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.079289] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.079292] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.079296] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.079301] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.079305] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.079309] dwc2 c90c0000.usb: DMA enabled
[  238.079312] dwc2 c90c0000.usb: desc DMA disabled
[  238.079316] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.079319] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[  238.079323] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.079328] dwc2 c90c0000.usb: set HCCHAR(3) to 00c89200
[  238.079331] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[  238.079335] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.079338] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.079342] dwc2 c90c0000.usb: 	 Is In: 1
[  238.079345] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.079349] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.079352] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.079356] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.079360] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.079364] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.079368] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.079371] dwc2 c90c0000.usb: no split
[  238.079376] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(3)
[  238.079379] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[  238.079383] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.079386] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.079390] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.079394] dwc2 c90c0000.usb: Wrote 1fb18000 to HCDMA(3)
[  238.079398] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.079402] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(3)
[  238.079412] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.079416] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.079441] dwc2 c90c0000.usb:   Device address: 3
[  238.079445] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.079449] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.079452] dwc2 c90c0000.usb:   Speed: HIGH
[  238.079456] dwc2 c90c0000.usb:   Max packet size: 512
[  238.079459] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.079464] dwc2 c90c0000.usb:   Transfer buffer: 43d704ae, Transfer DMA: 1fcf4000
[  238.079468] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.079472] dwc2 c90c0000.usb:   Interval: 0
[  238.079478] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.079483] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.079496] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.079501] dwc2 c90c0000.usb: urb_enqueue, urb f8714879
[  238.079504] dwc2 c90c0000.usb:   Device address: 3
[  238.079508] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.079512] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.079515] dwc2 c90c0000.usb:   Speed: HIGH
[  238.079519] dwc2 c90c0000.usb:   Max packet size: 512
[  238.079523] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.079527] dwc2 c90c0000.usb:   Transfer buffer: e2e574c5, Transfer DMA: 1fa22000
[  238.079531] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.079535] dwc2 c90c0000.usb:   Interval: 0
[  238.079540] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.079549] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.079558] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.079563] dwc2 c90c0000.usb: urb_enqueue, urb 9084c402
[  238.079566] dwc2 c90c0000.usb:   Device address: 3
[  238.079570] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.079574] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.079577] dwc2 c90c0000.usb:   Speed: HIGH
[  238.079581] dwc2 c90c0000.usb:   Max packet size: 512
[  238.079584] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.079589] dwc2 c90c0000.usb:   Transfer buffer: a6c9f8ab, Transfer DMA: 2e266000
[  238.079593] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.079596] dwc2 c90c0000.usb:   Interval: 0
[  238.079602] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.079606] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.079615] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.079619] dwc2 c90c0000.usb: urb_enqueue, urb 84dbe9e8
[  238.079623] dwc2 c90c0000.usb:   Device address: 3
[  238.079626] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.079630] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.079634] dwc2 c90c0000.usb:   Speed: HIGH
[  238.079637] dwc2 c90c0000.usb:   Max packet size: 512
[  238.079641] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.079645] dwc2 c90c0000.usb:   Transfer buffer: e5299216, Transfer DMA: 1fb68000
[  238.079649] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.079653] dwc2 c90c0000.usb:   Interval: 0
[  238.079658] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.079662] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.079675] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.079680] dwc2 c90c0000.usb: urb_enqueue, urb d4475b7d
[  238.079683] dwc2 c90c0000.usb:   Device address: 3
[  238.079687] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.079693] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.079696] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.079700] dwc2 c90c0000.usb: HAINT=00000008
[  238.079704] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[  238.079708] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.079713] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[  238.079717] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[  238.079721] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[  238.079724] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.079729] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.079733] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 3
[  238.079737] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.079740] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.079744] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.079747] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.079752] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.079758] dwc2 c90c0000.usb: dwc2_host_complete: urb 544633e2 device 3 ep 2-IN status 0 actual 8192
[  238.079763] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.079766] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.079769] dwc2 c90c0000.usb: DMA enabled
[  238.079774] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 2
[  238.079779] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.079783] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.079786] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.079790] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.079795] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.079799] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.079802] dwc2 c90c0000.usb: DMA enabled
[  238.079805] dwc2 c90c0000.usb: desc DMA disabled
[  238.079809] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.079813] dwc2 c90c0000.usb: set HAINTMSK to 00000010
[  238.079817] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.079822] dwc2 c90c0000.usb: set HCCHAR(4) to 00c89200
[  238.079825] dwc2 c90c0000.usb: dwc2_hc_init: Channel 4
[  238.079829] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.079832] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.079835] dwc2 c90c0000.usb: 	 Is In: 1
[  238.079839] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.079842] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.079846] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.079850] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.079853] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.079857] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.079861] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.079865] dwc2 c90c0000.usb: no split
[  238.079869] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(4)
[  238.079873] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 4
[  238.079877] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.079880] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.079884] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.079889] dwc2 c90c0000.usb: Wrote 2d262000 to HCDMA(4)
[  238.079892] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.079897] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(4)
[  238.079901] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.079905] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.079929] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.079933] dwc2 c90c0000.usb:   Speed: HIGH
[  238.079937] dwc2 c90c0000.usb:   Max packet size: 512
[  238.079941] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.079945] dwc2 c90c0000.usb:   Transfer buffer: 855e8e8f, Transfer DMA: 1f990000
[  238.079950] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.079953] dwc2 c90c0000.usb:   Interval: 0
[  238.079959] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.079964] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.079975] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.079980] dwc2 c90c0000.usb: urb_enqueue, urb a7f6c107
[  238.079983] dwc2 c90c0000.usb:   Device address: 3
[  238.079987] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.079991] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.079994] dwc2 c90c0000.usb:   Speed: HIGH
[  238.079998] dwc2 c90c0000.usb:   Max packet size: 512
[  238.080001] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.080006] dwc2 c90c0000.usb:   Transfer buffer: 6c600fcc, Transfer DMA: 1f800000
[  238.080010] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.080013] dwc2 c90c0000.usb:   Interval: 0
[  238.080019] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.080023] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.080036] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.080040] dwc2 c90c0000.usb: urb_enqueue, urb 8c3fa95c
[  238.080050] dwc2 c90c0000.usb:   Device address: 3
[  238.080053] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.080057] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.080061] dwc2 c90c0000.usb:   Speed: HIGH
[  238.080065] dwc2 c90c0000.usb:   Max packet size: 512
[  238.080068] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.080073] dwc2 c90c0000.usb:   Transfer buffer: 461ae8ec, Transfer DMA: 1fc02000
[  238.080078] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.080081] dwc2 c90c0000.usb:   Interval: 0
[  238.080087] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.080091] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.080101] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.080105] dwc2 c90c0000.usb: urb_enqueue, urb 3d621ba8
[  238.080109] dwc2 c90c0000.usb:   Device address: 3
[  238.080112] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.080116] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.080119] dwc2 c90c0000.usb:   Speed: HIGH
[  238.080123] dwc2 c90c0000.usb:   Max packet size: 512
[  238.080127] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.080131] dwc2 c90c0000.usb:   Transfer buffer: a419190f, Transfer DMA: 1fcea000
[  238.080135] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.080138] dwc2 c90c0000.usb:   Interval: 0
[  238.080144] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.080149] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.080158] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.080162] dwc2 c90c0000.usb: urb_enqueue, urb 6510a936
[  238.080170] dwc2 c90c0000.usb:   Device address: 3
[  238.080175] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.080178] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.080182] dwc2 c90c0000.usb:   Speed: HIGH
[  238.080185] dwc2 c90c0000.usb:   Max packet size: 512
[  238.080193] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.080196] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.080206] dwc2 c90c0000.usb: HAINT=00000010
[  238.080210] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 4
[  238.080214] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.080219] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Channel Halted--
[  238.080223] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: DMA Channel Halted--
[  238.080227] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Transfer Complete--
[  238.080230] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.080235] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.080239] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 4
[  238.080243] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.080246] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.080250] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.080253] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.080257] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.080263] dwc2 c90c0000.usb: dwc2_host_complete: urb cd91f79f device 3 ep 2-IN status 0 actual 8192
[  238.080269] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.080273] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.080276] dwc2 c90c0000.usb: DMA enabled
[  238.080281] dwc2 c90c0000.usb:   dwc2_release_channel: channel 4, halt_status 2
[  238.080286] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.080290] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.080293] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.080296] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.080301] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.080305] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.080309] dwc2 c90c0000.usb: DMA enabled
[  238.080312] dwc2 c90c0000.usb: desc DMA disabled
[  238.080315] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.080319] dwc2 c90c0000.usb: set HAINTMSK to 00000040
[  238.080323] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.080327] dwc2 c90c0000.usb: set HCCHAR(6) to 00c89200
[  238.080331] dwc2 c90c0000.usb: dwc2_hc_init: Channel 6
[  238.080334] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.080338] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.080341] dwc2 c90c0000.usb: 	 Is In: 1
[  238.080344] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.080348] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.080351] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.080356] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.080359] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.080363] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.080367] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.080370] dwc2 c90c0000.usb: no split
[  238.080375] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(6)
[  238.080378] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 6
[  238.080382] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.080385] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.080389] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.080393] dwc2 c90c0000.usb: Wrote 1fcfa000 to HCDMA(6)
[  238.080397] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.080401] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(6)
[  238.080405] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.080409] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.080425] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.080431] dwc2 c90c0000.usb:   Transfer buffer: c6791995, Transfer DMA: 1fe94000
[  238.080435] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.080439] dwc2 c90c0000.usb:   Interval: 0
[  238.080444] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.080449] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.080684] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.080688] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.080693] dwc2 c90c0000.usb: HAINT=00000040
[  238.080697] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 6
[  238.080701] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.080705] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Channel Halted--
[  238.080709] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: DMA Channel Halted--
[  238.080714] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Transfer Complete--
[  238.080717] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.080722] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.080726] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 6
[  238.080730] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.080733] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.080737] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.080740] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.080744] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.080751] dwc2 c90c0000.usb: dwc2_host_complete: urb 67466227 device 3 ep 2-IN status 0 actual 8192
[  238.080756] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.080760] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.080763] dwc2 c90c0000.usb: DMA enabled
[  238.080767] dwc2 c90c0000.usb:   dwc2_release_channel: channel 6, halt_status 2
[  238.080773] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.080776] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.080780] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.080784] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.080789] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.080793] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.080796] dwc2 c90c0000.usb: DMA enabled
[  238.080799] dwc2 c90c0000.usb: desc DMA disabled
[  238.080803] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.080807] dwc2 c90c0000.usb: set HAINTMSK to 00000020
[  238.080811] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.080815] dwc2 c90c0000.usb: set HCCHAR(5) to 00c89200
[  238.080819] dwc2 c90c0000.usb: dwc2_hc_init: Channel 5
[  238.080822] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.080826] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.080829] dwc2 c90c0000.usb: 	 Is In: 1
[  238.080832] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.080836] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.080839] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.080843] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.080847] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.080851] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.080854] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.080858] dwc2 c90c0000.usb: no split
[  238.080863] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(5)
[  238.080867] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 5
[  238.080870] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.080874] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.080877] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.080882] dwc2 c90c0000.usb: Wrote 2d274000 to HCDMA(5)
[  238.080885] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.080890] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(5)
[  238.080894] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.080898] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.081184] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.081189] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.081192] dwc2 c90c0000.usb: HAINT=00000020
[  238.081196] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 5
[  238.081201] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.081205] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Channel Halted--
[  238.081209] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: DMA Channel Halted--
[  238.081213] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Transfer Complete--
[  238.081217] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.081221] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.081225] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 5
[  238.081229] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.081232] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.081236] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.081240] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.081243] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.081250] dwc2 c90c0000.usb: dwc2_host_complete: urb a7ce381f device 3 ep 2-IN status 0 actual 8192
[  238.081255] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.081259] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.081262] dwc2 c90c0000.usb: DMA enabled
[  238.081267] dwc2 c90c0000.usb:   dwc2_release_channel: channel 5, halt_status 2
[  238.081272] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.081275] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.081279] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.081282] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.081288] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.081291] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.081295] dwc2 c90c0000.usb: DMA enabled
[  238.081298] dwc2 c90c0000.usb: desc DMA disabled
[  238.081302] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.081305] dwc2 c90c0000.usb: set HAINTMSK to 00000080
[  238.081309] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.081313] dwc2 c90c0000.usb: set HCCHAR(7) to 00c89200
[  238.081317] dwc2 c90c0000.usb: dwc2_hc_init: Channel 7
[  238.081321] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.081324] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.081327] dwc2 c90c0000.usb: 	 Is In: 1
[  238.081331] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.081334] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.081338] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.081341] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.081345] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.081349] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.081353] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.081356] dwc2 c90c0000.usb: no split
[  238.081360] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(7)
[  238.081364] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 7
[  238.081368] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.081371] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.081375] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.081379] dwc2 c90c0000.usb: Wrote 1fac6000 to HCDMA(7)
[  238.081383] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.081387] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(7)
[  238.081391] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.081395] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.081662] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.081666] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.081670] dwc2 c90c0000.usb: HAINT=00000080
[  238.081674] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 7
[  238.081679] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.081683] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Channel Halted--
[  238.081686] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: DMA Channel Halted--
[  238.081690] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Transfer Complete--
[  238.081694] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.081698] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.081702] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 7
[  238.081706] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.081709] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.081713] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.081717] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.081726] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.081732] dwc2 c90c0000.usb: dwc2_host_complete: urb 5f70d834 device 3 ep 2-IN status 0 actual 8192
[  238.081737] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.081741] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.081744] dwc2 c90c0000.usb: DMA enabled
[  238.081748] dwc2 c90c0000.usb:   dwc2_release_channel: channel 7, halt_status 2
[  238.081754] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.081758] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.081761] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.081764] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.081770] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.081773] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.081777] dwc2 c90c0000.usb: DMA enabled
[  238.081780] dwc2 c90c0000.usb: desc DMA disabled
[  238.081784] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.081788] dwc2 c90c0000.usb: set HAINTMSK to 00000100
[  238.081791] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.081796] dwc2 c90c0000.usb: set HCCHAR(8) to 00c89200
[  238.081800] dwc2 c90c0000.usb: dwc2_hc_init: Channel 8
[  238.081803] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.081806] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.081810] dwc2 c90c0000.usb: 	 Is In: 1
[  238.081813] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.081817] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.081820] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.081824] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.081827] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.081831] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.081835] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.081838] dwc2 c90c0000.usb: no split
[  238.081842] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(8)
[  238.081846] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 8
[  238.081850] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.081853] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.081857] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.081861] dwc2 c90c0000.usb: Wrote 1fcf4000 to HCDMA(8)
[  238.081865] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.081869] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(8)
[  238.081873] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.081877] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.082162] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.082166] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.082170] dwc2 c90c0000.usb: HAINT=00000100
[  238.082174] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 8
[  238.082179] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.082183] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Channel Halted--
[  238.082186] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: DMA Channel Halted--
[  238.082190] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Transfer Complete--
[  238.082194] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.082199] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.082203] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 8
[  238.082206] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.082210] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.082213] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.082217] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.082221] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.082227] dwc2 c90c0000.usb: dwc2_host_complete: urb c4a7e8a9 device 3 ep 2-IN status 0 actual 8192
[  238.082232] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.082235] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.082238] dwc2 c90c0000.usb: DMA enabled
[  238.082243] dwc2 c90c0000.usb:   dwc2_release_channel: channel 8, halt_status 2
[  238.082248] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.082252] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.082255] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.082259] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.082264] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.082269] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.082272] dwc2 c90c0000.usb: DMA enabled
[  238.082275] dwc2 c90c0000.usb: desc DMA disabled
[  238.082279] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.082283] dwc2 c90c0000.usb: set HAINTMSK to 00000200
[  238.082287] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.082291] dwc2 c90c0000.usb: set HCCHAR(9) to 00c89200
[  238.082295] dwc2 c90c0000.usb: dwc2_hc_init: Channel 9
[  238.082298] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.082302] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.082305] dwc2 c90c0000.usb: 	 Is In: 1
[  238.082309] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.082312] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.082316] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.082319] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.082323] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.082327] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.082331] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.082334] dwc2 c90c0000.usb: no split
[  238.082339] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(9)
[  238.082343] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 9
[  238.082346] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.082350] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.082353] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.082357] dwc2 c90c0000.usb: Wrote 1fa22000 to HCDMA(9)
[  238.082361] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.082365] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(9)
[  238.082369] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.082374] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.082640] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.082645] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.082648] dwc2 c90c0000.usb: HAINT=00000200
[  238.082653] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 9
[  238.082657] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.082661] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Channel Halted--
[  238.082665] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: DMA Channel Halted--
[  238.082669] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Transfer Complete--
[  238.082673] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.082677] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.082681] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 9
[  238.082685] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.082688] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.082692] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.082696] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.082699] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.082705] dwc2 c90c0000.usb: dwc2_host_complete: urb f8714879 device 3 ep 2-IN status 0 actual 8192
[  238.082711] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.082715] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.082718] dwc2 c90c0000.usb: DMA enabled
[  238.082723] dwc2 c90c0000.usb:   dwc2_release_channel: channel 9, halt_status 2
[  238.082728] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.082731] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.082735] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.082738] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.082744] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.082747] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.082751] dwc2 c90c0000.usb: DMA enabled
[  238.082754] dwc2 c90c0000.usb: desc DMA disabled
[  238.082758] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.082761] dwc2 c90c0000.usb: set HAINTMSK to 00000400
[  238.082765] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.082770] dwc2 c90c0000.usb: set HCCHAR(10) to 00c89200
[  238.082773] dwc2 c90c0000.usb: dwc2_hc_init: Channel 10
[  238.082777] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.082780] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.082784] dwc2 c90c0000.usb: 	 Is In: 1
[  238.082787] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.082791] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.082794] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.082798] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.082802] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.082806] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.082809] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.082813] dwc2 c90c0000.usb: no split
[  238.082817] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(10)
[  238.082821] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 10
[  238.082825] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.082828] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.082832] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.082836] dwc2 c90c0000.usb: Wrote 2e266000 to HCDMA(10)
[  238.082839] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.082843] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(10)
[  238.082848] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.082852] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.083136] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.083141] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.083144] dwc2 c90c0000.usb: HAINT=00000400
[  238.083149] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 10
[  238.083153] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.083157] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Channel Halted--
[  238.083161] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: DMA Channel Halted--
[  238.083165] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Transfer Complete--
[  238.083169] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.083173] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.083177] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 10
[  238.083181] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.083184] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.083188] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.083191] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.083195] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.083201] dwc2 c90c0000.usb: dwc2_host_complete: urb 9084c402 device 3 ep 2-IN status 0 actual 8192
[  238.083209] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.083213] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.083216] dwc2 c90c0000.usb: DMA enabled
[  238.083220] dwc2 c90c0000.usb:   dwc2_release_channel: channel 10, halt_status 2
[  238.083226] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.083229] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.083233] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.083236] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.083242] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.083246] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.083249] dwc2 c90c0000.usb: DMA enabled
[  238.083252] dwc2 c90c0000.usb: desc DMA disabled
[  238.083256] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.083260] dwc2 c90c0000.usb: set HAINTMSK to 00000800
[  238.083263] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.083268] dwc2 c90c0000.usb: set HCCHAR(11) to 00c89200
[  238.083272] dwc2 c90c0000.usb: dwc2_hc_init: Channel 11
[  238.083275] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.083278] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.083282] dwc2 c90c0000.usb: 	 Is In: 1
[  238.083285] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.083289] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.083292] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.083296] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.083300] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.083304] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.083308] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.083311] dwc2 c90c0000.usb: no split
[  238.083316] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(11)
[  238.083319] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 11
[  238.083323] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.083327] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.083330] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.083334] dwc2 c90c0000.usb: Wrote 1fb68000 to HCDMA(11)
[  238.083338] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.083342] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(11)
[  238.083346] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.083351] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.083616] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.083621] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.083625] dwc2 c90c0000.usb: HAINT=00000800
[  238.083629] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 11
[  238.083633] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.083637] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Channel Halted--
[  238.083641] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: DMA Channel Halted--
[  238.083645] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Transfer Complete--
[  238.083648] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.083653] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.083657] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 11
[  238.083661] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.083664] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.083668] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.083671] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.083675] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.083681] dwc2 c90c0000.usb: dwc2_host_complete: urb 84dbe9e8 device 3 ep 2-IN status 0 actual 8192
[  238.083686] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.083690] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.083693] dwc2 c90c0000.usb: DMA enabled
[  238.083698] dwc2 c90c0000.usb:   dwc2_release_channel: channel 11, halt_status 2
[  238.083703] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.083707] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.083710] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.083713] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.083718] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.083722] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.083726] dwc2 c90c0000.usb: DMA enabled
[  238.083729] dwc2 c90c0000.usb: desc DMA disabled
[  238.083732] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.083736] dwc2 c90c0000.usb: set HAINTMSK to 00001000
[  238.083740] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.083744] dwc2 c90c0000.usb: set HCCHAR(12) to 00c89200
[  238.083748] dwc2 c90c0000.usb: dwc2_hc_init: Channel 12
[  238.083752] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.083755] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.083758] dwc2 c90c0000.usb: 	 Is In: 1
[  238.083762] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.083765] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.083769] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.083773] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.083776] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.083780] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.083784] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.083787] dwc2 c90c0000.usb: no split
[  238.083792] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(12)
[  238.083795] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 12
[  238.083799] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.083802] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.083806] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.083810] dwc2 c90c0000.usb: Wrote 1f990000 to HCDMA(12)
[  238.083814] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.083818] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(12)
[  238.083823] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.083827] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.084116] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.084123] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.084127] dwc2 c90c0000.usb: HAINT=00001000
[  238.084132] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 12
[  238.084137] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.084141] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Channel Halted--
[  238.084145] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: DMA Channel Halted--
[  238.084149] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Transfer Complete--
[  238.084153] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.084157] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.084162] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 12
[  238.084165] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.084169] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.084172] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.084176] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.084180] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.084187] dwc2 c90c0000.usb: dwc2_host_complete: urb d4475b7d device 3 ep 2-IN status 0 actual 8192
[  238.084193] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.084197] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.084200] dwc2 c90c0000.usb: DMA enabled
[  238.084205] dwc2 c90c0000.usb:   dwc2_release_channel: channel 12, halt_status 2
[  238.084211] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.084215] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.084218] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.084222] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.084228] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.084232] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.084236] dwc2 c90c0000.usb: DMA enabled
[  238.084239] dwc2 c90c0000.usb: desc DMA disabled
[  238.084242] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.084246] dwc2 c90c0000.usb: set HAINTMSK to 00002000
[  238.084251] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.084255] dwc2 c90c0000.usb: set HCCHAR(13) to 00c89200
[  238.084259] dwc2 c90c0000.usb: dwc2_hc_init: Channel 13
[  238.084262] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.084266] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.084269] dwc2 c90c0000.usb: 	 Is In: 1
[  238.084273] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.084276] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.084280] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.084284] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.084288] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.084292] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.084296] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.084300] dwc2 c90c0000.usb: no split
[  238.084305] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(13)
[  238.084308] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 13
[  238.084312] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.084315] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.084320] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.084324] dwc2 c90c0000.usb: Wrote 1f800000 to HCDMA(13)
[  238.084328] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.084332] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(13)
[  238.084336] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.084341] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.084608] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.084614] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.084618] dwc2 c90c0000.usb: HAINT=00002000
[  238.084622] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 13
[  238.084627] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.084631] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Channel Halted--
[  238.084635] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: DMA Channel Halted--
[  238.084639] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Transfer Complete--
[  238.084642] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.084647] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.084651] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 13
[  238.084655] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.084658] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.084662] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.084666] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.084669] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.084676] dwc2 c90c0000.usb: dwc2_host_complete: urb a7f6c107 device 3 ep 2-IN status 0 actual 8192
[  238.084682] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.084685] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.084689] dwc2 c90c0000.usb: DMA enabled
[  238.084693] dwc2 c90c0000.usb:   dwc2_release_channel: channel 13, halt_status 2
[  238.084698] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.084702] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.084706] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.084709] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.084715] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.084719] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.084723] dwc2 c90c0000.usb: DMA enabled
[  238.084726] dwc2 c90c0000.usb: desc DMA disabled
[  238.084730] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.084733] dwc2 c90c0000.usb: set HAINTMSK to 00004000
[  238.084737] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.084742] dwc2 c90c0000.usb: set HCCHAR(14) to 00c89200
[  238.084745] dwc2 c90c0000.usb: dwc2_hc_init: Channel 14
[  238.084749] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.084752] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.084756] dwc2 c90c0000.usb: 	 Is In: 1
[  238.084759] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.084763] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.084766] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.084770] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.084774] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.084778] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.084782] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.084785] dwc2 c90c0000.usb: no split
[  238.084790] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(14)
[  238.084793] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 14
[  238.084797] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.084801] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.084804] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.084808] dwc2 c90c0000.usb: Wrote 1fc02000 to HCDMA(14)
[  238.084812] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.084816] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(14)
[  238.084820] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.084825] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.085109] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.085115] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.085119] dwc2 c90c0000.usb: HAINT=00004000
[  238.085123] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 14
[  238.085127] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.085132] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Channel Halted--
[  238.085135] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: DMA Channel Halted--
[  238.085140] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Transfer Complete--
[  238.085143] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.085148] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.085152] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 14
[  238.085155] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.085159] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.085162] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.085166] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.085170] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.085176] dwc2 c90c0000.usb: dwc2_host_complete: urb 8c3fa95c device 3 ep 2-IN status 0 actual 8192
[  238.085182] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.085185] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.085189] dwc2 c90c0000.usb: DMA enabled
[  238.085193] dwc2 c90c0000.usb:   dwc2_release_channel: channel 14, halt_status 2
[  238.085199] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.085203] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.085206] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.085209] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.085215] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.085219] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.085223] dwc2 c90c0000.usb: DMA enabled
[  238.085226] dwc2 c90c0000.usb: desc DMA disabled
[  238.085229] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.085233] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[  238.085237] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.085241] dwc2 c90c0000.usb: set HCCHAR(0) to 00c89200
[  238.085245] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[  238.085248] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.085252] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.085255] dwc2 c90c0000.usb: 	 Is In: 1
[  238.085258] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.085262] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.085266] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.085270] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.085273] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.085277] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.085281] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.085285] dwc2 c90c0000.usb: no split
[  238.085289] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(0)
[  238.085293] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[  238.085296] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.085300] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.085303] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.085308] dwc2 c90c0000.usb: Wrote 1fcea000 to HCDMA(0)
[  238.085311] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.085315] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(0)
[  238.085320] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.085329] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.085591] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.085596] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.085600] dwc2 c90c0000.usb: HAINT=00000001
[  238.085604] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[  238.085608] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.085613] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Channel Halted--
[  238.085617] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: DMA Channel Halted--
[  238.085621] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Transfer Complete--
[  238.085625] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.085629] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.085633] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 0
[  238.085637] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.085640] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.085644] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.085648] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.085651] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.085658] dwc2 c90c0000.usb: dwc2_host_complete: urb 3d621ba8 device 3 ep 2-IN status 0 actual 8192
[  238.085663] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.085666] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.085670] dwc2 c90c0000.usb: DMA enabled
[  238.085674] dwc2 c90c0000.usb:   dwc2_release_channel: channel 0, halt_status 2
[  238.085679] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.085683] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.085686] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.085690] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.085695] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.085699] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.085702] dwc2 c90c0000.usb: DMA enabled
[  238.085706] dwc2 c90c0000.usb: desc DMA disabled
[  238.085709] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.085713] dwc2 c90c0000.usb: set HAINTMSK to 00008000
[  238.085717] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.085721] dwc2 c90c0000.usb: set HCCHAR(15) to 00c89200
[  238.085725] dwc2 c90c0000.usb: dwc2_hc_init: Channel 15
[  238.085728] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.085732] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.085736] dwc2 c90c0000.usb: 	 Is In: 1
[  238.085739] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.085742] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.085746] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.085750] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.085753] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.085757] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.085761] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.085764] dwc2 c90c0000.usb: no split
[  238.085768] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(15)
[  238.085772] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 15
[  238.085776] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.085779] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.085783] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.085787] dwc2 c90c0000.usb: Wrote 1fe94000 to HCDMA(15)
[  238.085791] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.085795] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(15)
[  238.085799] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.085804] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.086087] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.086093] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.086097] dwc2 c90c0000.usb: HAINT=00008000
[  238.086101] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 15
[  238.086106] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.086110] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Channel Halted--
[  238.086113] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: DMA Channel Halted--
[  238.086117] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Transfer Complete--
[  238.086121] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.086125] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.086130] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 15
[  238.086133] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.086137] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.086140] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.086144] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.086154] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.086160] dwc2 c90c0000.usb: dwc2_host_complete: urb 6510a936 device 3 ep 2-IN status 0 actual 8192
[  238.086165] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.086169] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.086172] dwc2 c90c0000.usb: DMA enabled
[  238.086176] dwc2 c90c0000.usb:   dwc2_release_channel: channel 15, halt_status 2
[  238.086181] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.086185] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.086189] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.086193] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.086197] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.086255] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.086261] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.086265] dwc2 c90c0000.usb:   Device address: 3
[  238.086269] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.086273] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.086276] dwc2 c90c0000.usb:   Speed: HIGH
[  238.086281] dwc2 c90c0000.usb:   Max packet size: 512
[  238.086284] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.086289] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.086301] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.086304] dwc2 c90c0000.usb:   Interval: 0
[  238.086311] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.086316] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.086424] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.086428] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.086432] dwc2 c90c0000.usb: DMA enabled
[  238.086435] dwc2 c90c0000.usb: desc DMA disabled
[  238.086439] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.086443] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[  238.086447] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.086451] dwc2 c90c0000.usb: set HCCHAR(1) to 00c89200
[  238.086455] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[  238.086458] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.086462] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.086465] dwc2 c90c0000.usb: 	 Is In: 1
[  238.086468] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.086472] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.086475] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.086479] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.086483] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.086487] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.086491] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.086494] dwc2 c90c0000.usb: no split
[  238.086499] dwc2 c90c0000.usb: Wrote 40080200 to HCTSIZ(1)
[  238.086502] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[  238.086506] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.086509] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.086513] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.086517] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(1)
[  238.086521] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.086525] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(1)
[  238.086534] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.086538] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.086541] dwc2 c90c0000.usb: HAINT=00000002
[  238.086546] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[  238.086550] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.086555] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[  238.086559] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[  238.086563] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[  238.086567] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.086571] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.086576] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 1
[  238.086579] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.086583] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.086586] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.086590] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.086594] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.086600] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.086605] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.086608] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.086611] dwc2 c90c0000.usb: DMA enabled
[  238.086616] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 2
[  238.086621] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.086625] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.086628] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.086633] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.086638] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.086744] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.086750] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.086754] dwc2 c90c0000.usb:   Device address: 3
[  238.086758] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.086762] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.086766] dwc2 c90c0000.usb:   Speed: HIGH
[  238.086770] dwc2 c90c0000.usb:   Max packet size: 512
[  238.086773] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.086778] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.086782] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.086786] dwc2 c90c0000.usb:   Interval: 0
[  238.086798] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.086803] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.086922] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.086927] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.086931] dwc2 c90c0000.usb: DMA enabled
[  238.086934] dwc2 c90c0000.usb: desc DMA disabled
[  238.086938] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.086942] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[  238.086946] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.086950] dwc2 c90c0000.usb: set HCCHAR(2) to 00c80a00
[  238.086960] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[  238.086963] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.086967] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.086970] dwc2 c90c0000.usb: 	 Is In: 0
[  238.086974] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.086977] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.086981] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.086985] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.086989] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.086992] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.086996] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.087000] dwc2 c90c0000.usb: no split
[  238.087005] dwc2 c90c0000.usb: Wrote 0008001f to HCTSIZ(2)
[  238.087009] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[  238.087012] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.087016] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.087019] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.087023] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(2)
[  238.087027] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.087031] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(2)
[  238.087041] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.087045] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.087048] dwc2 c90c0000.usb: HAINT=00000004
[  238.087052] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[  238.087057] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.087061] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[  238.087065] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[  238.087069] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[  238.087073] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.087077] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.087082] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 2
[  238.087085] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.087089] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.087092] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.087096] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.087100] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.087107] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.087112] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.087117] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 2
[  238.087122] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.087126] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.087129] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.087134] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.087138] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.087176] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.087182] dwc2 c90c0000.usb: urb_enqueue, urb 64d8cdc0
[  238.087185] dwc2 c90c0000.usb:   Device address: 3
[  238.087189] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.087193] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.087197] dwc2 c90c0000.usb:   Speed: HIGH
[  238.087200] dwc2 c90c0000.usb:   Max packet size: 512
[  238.087204] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.087209] dwc2 c90c0000.usb:   Transfer buffer: 9e5b4c16, Transfer DMA: 2e22e000
[  238.087213] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.087217] dwc2 c90c0000.usb:   Interval: 0
[  238.087223] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.087227] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.087298] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.087302] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.087306] dwc2 c90c0000.usb: DMA enabled
[  238.087309] dwc2 c90c0000.usb: desc DMA disabled
[  238.087313] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.087317] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[  238.087321] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.087325] dwc2 c90c0000.usb: set HCCHAR(3) to 00c89200
[  238.087329] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[  238.087332] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.087336] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.087339] dwc2 c90c0000.usb: 	 Is In: 1
[  238.087342] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.087346] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.087349] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.087353] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.087357] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.087361] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.087365] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.087368] dwc2 c90c0000.usb: no split
[  238.087373] dwc2 c90c0000.usb: Wrote 00802000 to HCTSIZ(3)
[  238.087377] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[  238.087380] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.087384] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.087388] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.087392] dwc2 c90c0000.usb: Wrote 2e22e000 to HCDMA(3)
[  238.087395] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.087400] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(3)
[  238.087694] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.087698] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.087702] dwc2 c90c0000.usb: HAINT=00000008
[  238.087706] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[  238.087710] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.087715] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[  238.087719] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[  238.087723] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[  238.087726] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.087731] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.087741] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 3
[  238.087744] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.087748] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.087751] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.087755] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.087759] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.087765] dwc2 c90c0000.usb: dwc2_host_complete: urb 64d8cdc0 device 3 ep 2-IN status 0 actual 8192
[  238.087770] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.087774] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.087777] dwc2 c90c0000.usb: DMA enabled
[  238.087782] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 2
[  238.087787] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.087791] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.087794] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.087799] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.087803] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.087837] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.087843] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.087847] dwc2 c90c0000.usb:   Device address: 3
[  238.087851] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.087855] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.087858] dwc2 c90c0000.usb:   Speed: HIGH
[  238.087862] dwc2 c90c0000.usb:   Max packet size: 512
[  238.087866] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.087870] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.087875] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.087878] dwc2 c90c0000.usb:   Interval: 0
[  238.087884] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.087889] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.087924] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.087928] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.087931] dwc2 c90c0000.usb: DMA enabled
[  238.087934] dwc2 c90c0000.usb: desc DMA disabled
[  238.087938] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.087942] dwc2 c90c0000.usb: set HAINTMSK to 00000010
[  238.087946] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.087950] dwc2 c90c0000.usb: set HCCHAR(4) to 00c89200
[  238.087954] dwc2 c90c0000.usb: dwc2_hc_init: Channel 4
[  238.087957] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.087961] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.087964] dwc2 c90c0000.usb: 	 Is In: 1
[  238.087968] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.087971] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.087975] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.087978] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.087982] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.087986] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.087990] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.087993] dwc2 c90c0000.usb: no split
[  238.087998] dwc2 c90c0000.usb: Wrote 00080200 to HCTSIZ(4)
[  238.088002] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 4
[  238.088005] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.088009] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.088012] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.088017] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(4)
[  238.088020] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.088025] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(4)
[  238.088034] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.088038] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.088041] dwc2 c90c0000.usb: HAINT=00000010
[  238.088045] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 4
[  238.088050] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.088054] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Channel Halted--
[  238.088058] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: DMA Channel Halted--
[  238.088062] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Transfer Complete--
[  238.088066] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.088070] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.088074] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 4
[  238.088078] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.088082] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.088085] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.088089] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.088093] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.088099] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.088103] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.088107] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.088111] dwc2 c90c0000.usb: DMA enabled
[  238.088115] dwc2 c90c0000.usb:   dwc2_release_channel: channel 4, halt_status 2
[  238.088120] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.088124] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.088127] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.088132] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.088136] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.088751] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.088761] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.088766] dwc2 c90c0000.usb:   Device address: 3
[  238.088771] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.088775] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.088778] dwc2 c90c0000.usb:   Speed: HIGH
[  238.088783] dwc2 c90c0000.usb:   Max packet size: 512
[  238.088787] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.088800] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.088805] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.088809] dwc2 c90c0000.usb:   Interval: 0
[  238.088816] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.088822] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.088924] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.088929] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.088932] dwc2 c90c0000.usb: DMA enabled
[  238.088936] dwc2 c90c0000.usb: desc DMA disabled
[  238.088940] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.088944] dwc2 c90c0000.usb: set HAINTMSK to 00000040
[  238.088948] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.088952] dwc2 c90c0000.usb: set HCCHAR(6) to 00c80a00
[  238.088956] dwc2 c90c0000.usb: dwc2_hc_init: Channel 6
[  238.088959] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.088962] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.088966] dwc2 c90c0000.usb: 	 Is In: 0
[  238.088970] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.088973] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.088977] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.088981] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.088985] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.088989] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.088994] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.088997] dwc2 c90c0000.usb: no split
[  238.089002] dwc2 c90c0000.usb: Wrote 4008001f to HCTSIZ(6)
[  238.089006] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 6
[  238.089010] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.089013] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.089017] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.089021] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(6)
[  238.089025] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.089029] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(6)
[  238.089040] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.089044] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.089048] dwc2 c90c0000.usb: HAINT=00000040
[  238.089052] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 6
[  238.089057] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.089061] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Channel Halted--
[  238.089065] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: DMA Channel Halted--
[  238.089070] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Transfer Complete--
[  238.089073] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.089078] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.089083] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 6
[  238.089086] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.089090] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.089093] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.089097] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.089101] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.089107] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.089114] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.089118] dwc2 c90c0000.usb:   dwc2_release_channel: channel 6, halt_status 2
[  238.089124] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.089127] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.089131] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.089136] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.089140] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.089184] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.089190] dwc2 c90c0000.usb: urb_enqueue, urb 64d8cdc0
[  238.089194] dwc2 c90c0000.usb:   Device address: 3
[  238.089198] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.089202] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.089205] dwc2 c90c0000.usb:   Speed: HIGH
[  238.089209] dwc2 c90c0000.usb:   Max packet size: 512
[  238.089213] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.089218] dwc2 c90c0000.usb:   Transfer buffer: 5b69ba28, Transfer DMA: 1f964000
[  238.089223] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.089226] dwc2 c90c0000.usb:   Interval: 0
[  238.089232] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.089237] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.089252] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.089256] dwc2 c90c0000.usb: urb_enqueue, urb 544633e2
[  238.089260] dwc2 c90c0000.usb:   Device address: 3
[  238.089263] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.089267] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.089271] dwc2 c90c0000.usb:   Speed: HIGH
[  238.089274] dwc2 c90c0000.usb:   Max packet size: 512
[  238.089278] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.089282] dwc2 c90c0000.usb:   Transfer buffer: 1f4971e3, Transfer DMA: 2e7a4000
[  238.089287] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.089296] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.089300] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.089304] dwc2 c90c0000.usb: DMA enabled
[  238.089307] dwc2 c90c0000.usb: desc DMA disabled
[  238.089311] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.089315] dwc2 c90c0000.usb: set HAINTMSK to 00000020
[  238.089319] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.089323] dwc2 c90c0000.usb: set HCCHAR(5) to 00c89200
[  238.089327] dwc2 c90c0000.usb: dwc2_hc_init: Channel 5
[  238.089331] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.089334] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.089338] dwc2 c90c0000.usb: 	 Is In: 1
[  238.089341] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.089345] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.089348] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.089352] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.089356] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.089359] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.089364] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.089367] dwc2 c90c0000.usb: no split
[  238.089372] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(5)
[  238.089376] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 5
[  238.089379] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.089383] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.089387] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.089391] dwc2 c90c0000.usb: Wrote 1f964000 to HCDMA(5)
[  238.089395] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.089399] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(5)
[  238.089404] dwc2 c90c0000.usb:   Interval: 0
[  238.089410] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.089416] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.090465] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.090470] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.090474] dwc2 c90c0000.usb: HAINT=00000020
[  238.090478] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 5
[  238.090483] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.090487] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Channel Halted--
[  238.090491] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: DMA Channel Halted--
[  238.090496] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Transfer Complete--
[  238.090500] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.090504] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.090509] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 5
[  238.090512] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.090516] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.090520] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.090523] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.090527] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.090533] dwc2 c90c0000.usb: dwc2_host_complete: urb 64d8cdc0 device 3 ep 2-IN status 0 actual 8192
[  238.090541] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.090544] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.090548] dwc2 c90c0000.usb: DMA enabled
[  238.090552] dwc2 c90c0000.usb:   dwc2_release_channel: channel 5, halt_status 2
[  238.090558] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.090562] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.090565] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.090569] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.090574] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.090578] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.090582] dwc2 c90c0000.usb: DMA enabled
[  238.090585] dwc2 c90c0000.usb: desc DMA disabled
[  238.090589] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.090593] dwc2 c90c0000.usb: set HAINTMSK to 00000080
[  238.090596] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.090601] dwc2 c90c0000.usb: set HCCHAR(7) to 00c89200
[  238.090605] dwc2 c90c0000.usb: dwc2_hc_init: Channel 7
[  238.090608] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.090612] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.090615] dwc2 c90c0000.usb: 	 Is In: 1
[  238.090619] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.090622] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.090625] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.090629] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.090633] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.090637] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.090641] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.090644] dwc2 c90c0000.usb: no split
[  238.090649] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(7)
[  238.090653] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 7
[  238.090656] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.090660] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.090663] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.090667] dwc2 c90c0000.usb: Wrote 2e7a4000 to HCDMA(7)
[  238.090671] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.090675] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(7)
[  238.090680] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.090684] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.090951] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.090955] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.090958] dwc2 c90c0000.usb: HAINT=00000080
[  238.090962] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 7
[  238.090967] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.090971] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Channel Halted--
[  238.090975] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: DMA Channel Halted--
[  238.090979] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Transfer Complete--
[  238.090983] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.090988] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.090992] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 7
[  238.090996] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.090999] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.091003] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.091006] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.091010] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.091016] dwc2 c90c0000.usb: dwc2_host_complete: urb 544633e2 device 3 ep 2-IN status 0 actual 8192
[  238.091021] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.091025] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.091028] dwc2 c90c0000.usb: DMA enabled
[  238.091032] dwc2 c90c0000.usb:   dwc2_release_channel: channel 7, halt_status 2
[  238.091038] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.091041] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.091050] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.091055] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.091059] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.091096] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.091102] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.091106] dwc2 c90c0000.usb:   Device address: 3
[  238.091110] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.091114] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.091117] dwc2 c90c0000.usb:   Speed: HIGH
[  238.091121] dwc2 c90c0000.usb:   Max packet size: 512
[  238.091125] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.091130] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.091134] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.091137] dwc2 c90c0000.usb:   Interval: 0
[  238.091144] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.091150] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.091174] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.091178] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.091181] dwc2 c90c0000.usb: DMA enabled
[  238.091185] dwc2 c90c0000.usb: desc DMA disabled
[  238.091188] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.091193] dwc2 c90c0000.usb: set HAINTMSK to 00000100
[  238.091197] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.091201] dwc2 c90c0000.usb: set HCCHAR(8) to 00c89200
[  238.091205] dwc2 c90c0000.usb: dwc2_hc_init: Channel 8
[  238.091208] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.091212] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.091215] dwc2 c90c0000.usb: 	 Is In: 1
[  238.091219] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.091222] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.091226] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.091229] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.091233] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.091237] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.091241] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.091244] dwc2 c90c0000.usb: no split
[  238.091248] dwc2 c90c0000.usb: Wrote 40080200 to HCTSIZ(8)
[  238.091252] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 8
[  238.091256] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.091259] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.091263] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.091267] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(8)
[  238.091271] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.091275] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(8)
[  238.091285] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.091289] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.091292] dwc2 c90c0000.usb: HAINT=00000100
[  238.091296] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 8
[  238.091301] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.091305] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Channel Halted--
[  238.091309] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: DMA Channel Halted--
[  238.091313] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Transfer Complete--
[  238.091317] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.091322] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.091326] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 8
[  238.091330] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.091334] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.091337] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.091341] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.091345] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.091352] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.091357] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.091360] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.091364] dwc2 c90c0000.usb: DMA enabled
[  238.091368] dwc2 c90c0000.usb:   dwc2_release_channel: channel 8, halt_status 2
[  238.091373] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.091377] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.091380] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.091385] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.091390] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.091492] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.091499] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.091503] dwc2 c90c0000.usb:   Device address: 3
[  238.091507] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.091511] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.091515] dwc2 c90c0000.usb:   Speed: HIGH
[  238.091519] dwc2 c90c0000.usb:   Max packet size: 512
[  238.091522] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.091527] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.091531] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.091535] dwc2 c90c0000.usb:   Interval: 0
[  238.091540] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.091550] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.091674] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.091679] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.091682] dwc2 c90c0000.usb: DMA enabled
[  238.091685] dwc2 c90c0000.usb: desc DMA disabled
[  238.091689] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.091693] dwc2 c90c0000.usb: set HAINTMSK to 00000200
[  238.091697] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.091701] dwc2 c90c0000.usb: set HCCHAR(9) to 00c80a00
[  238.091705] dwc2 c90c0000.usb: dwc2_hc_init: Channel 9
[  238.091708] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.091712] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.091715] dwc2 c90c0000.usb: 	 Is In: 0
[  238.091718] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.091722] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.091726] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.091730] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.091734] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.091737] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.091741] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.091745] dwc2 c90c0000.usb: no split
[  238.091749] dwc2 c90c0000.usb: Wrote 0008001f to HCTSIZ(9)
[  238.091753] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 9
[  238.091756] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.091760] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.091763] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.091768] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(9)
[  238.091771] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.091775] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(9)
[  238.091784] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.091789] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.091792] dwc2 c90c0000.usb: HAINT=00000200
[  238.091796] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 9
[  238.091801] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.091805] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Channel Halted--
[  238.091809] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: DMA Channel Halted--
[  238.091813] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Transfer Complete--
[  238.091817] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.091821] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.091826] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 9
[  238.091830] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.091833] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.091837] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.091846] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.091850] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.091857] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.091862] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.091867] dwc2 c90c0000.usb:   dwc2_release_channel: channel 9, halt_status 2
[  238.091872] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.091876] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.091880] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.091885] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.091889] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.091930] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.091936] dwc2 c90c0000.usb: urb_enqueue, urb 64d8cdc0
[  238.091940] dwc2 c90c0000.usb:   Device address: 3
[  238.091944] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.091948] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.091952] dwc2 c90c0000.usb:   Speed: HIGH
[  238.091955] dwc2 c90c0000.usb:   Max packet size: 512
[  238.091959] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.091964] dwc2 c90c0000.usb:   Transfer buffer: 337e3035, Transfer DMA: 1fcee000
[  238.091968] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.091972] dwc2 c90c0000.usb:   Interval: 0
[  238.091977] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.091982] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.092048] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.092052] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.092056] dwc2 c90c0000.usb: DMA enabled
[  238.092059] dwc2 c90c0000.usb: desc DMA disabled
[  238.092063] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.092066] dwc2 c90c0000.usb: set HAINTMSK to 00000400
[  238.092070] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.092075] dwc2 c90c0000.usb: set HCCHAR(10) to 00c89200
[  238.092078] dwc2 c90c0000.usb: dwc2_hc_init: Channel 10
[  238.092082] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.092085] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.092089] dwc2 c90c0000.usb: 	 Is In: 1
[  238.092092] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.092096] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.092099] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.092103] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.092107] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.092110] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.092114] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.092118] dwc2 c90c0000.usb: no split
[  238.092122] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(10)
[  238.092126] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 10
[  238.092130] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.092133] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.092137] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.092141] dwc2 c90c0000.usb: Wrote 1fcee000 to HCDMA(10)
[  238.092145] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.092149] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(10)
[  238.092249] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.092253] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.092257] dwc2 c90c0000.usb: HAINT=00000400
[  238.092261] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 10
[  238.092266] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.092270] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Channel Halted--
[  238.092274] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: DMA Channel Halted--
[  238.092278] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Transfer Complete--
[  238.092282] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.092286] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.092291] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 10
[  238.092294] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.092298] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.092301] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.092305] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.092309] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.092315] dwc2 c90c0000.usb: dwc2_host_complete: urb 64d8cdc0 device 3 ep 2-IN status 0 actual 4096
[  238.092319] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.092323] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.092326] dwc2 c90c0000.usb: DMA enabled
[  238.092331] dwc2 c90c0000.usb:   dwc2_release_channel: channel 10, halt_status 2
[  238.092336] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.092340] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.092343] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.092348] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.092352] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.092382] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.092387] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.092391] dwc2 c90c0000.usb:   Device address: 3
[  238.092395] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.092399] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.092402] dwc2 c90c0000.usb:   Speed: HIGH
[  238.092406] dwc2 c90c0000.usb:   Max packet size: 512
[  238.092409] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.092414] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.092424] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.092428] dwc2 c90c0000.usb:   Interval: 0
[  238.092434] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.092438] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.092549] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.092554] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.092558] dwc2 c90c0000.usb: DMA enabled
[  238.092561] dwc2 c90c0000.usb: desc DMA disabled
[  238.092565] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.092569] dwc2 c90c0000.usb: set HAINTMSK to 00000800
[  238.092572] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.092577] dwc2 c90c0000.usb: set HCCHAR(11) to 00c89200
[  238.092580] dwc2 c90c0000.usb: dwc2_hc_init: Channel 11
[  238.092584] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.092587] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.092591] dwc2 c90c0000.usb: 	 Is In: 1
[  238.092594] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.092598] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.092601] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.092605] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.092609] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.092612] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.092616] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.092620] dwc2 c90c0000.usb: no split
[  238.092624] dwc2 c90c0000.usb: Wrote 00080200 to HCTSIZ(11)
[  238.092628] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 11
[  238.092631] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.092640] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.092644] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.092648] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(11)
[  238.092652] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.092656] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(11)
[  238.092675] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.092679] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.092683] dwc2 c90c0000.usb: HAINT=00000800
[  238.092687] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 11
[  238.092692] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.092696] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Channel Halted--
[  238.092700] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: DMA Channel Halted--
[  238.092704] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Transfer Complete--
[  238.092708] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.092712] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.092716] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 11
[  238.092720] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.092723] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.092727] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.092731] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.092735] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.092741] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.092746] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.092749] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.092753] dwc2 c90c0000.usb: DMA enabled
[  238.092757] dwc2 c90c0000.usb:   dwc2_release_channel: channel 11, halt_status 2
[  238.092762] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.092766] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.092769] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.092774] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.092779] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.092865] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.092871] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.092875] dwc2 c90c0000.usb:   Device address: 3
[  238.092879] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.092883] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.092886] dwc2 c90c0000.usb:   Speed: HIGH
[  238.092890] dwc2 c90c0000.usb:   Max packet size: 512
[  238.092894] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.092899] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.092903] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.092906] dwc2 c90c0000.usb:   Interval: 0
[  238.092913] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.092923] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.093049] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.093054] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.093058] dwc2 c90c0000.usb: DMA enabled
[  238.093061] dwc2 c90c0000.usb: desc DMA disabled
[  238.093065] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.093069] dwc2 c90c0000.usb: set HAINTMSK to 00001000
[  238.093073] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.093077] dwc2 c90c0000.usb: set HCCHAR(12) to 00c80a00
[  238.093081] dwc2 c90c0000.usb: dwc2_hc_init: Channel 12
[  238.093084] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.093088] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.093091] dwc2 c90c0000.usb: 	 Is In: 0
[  238.093095] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.093098] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.093102] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.093106] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.093110] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.093113] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.093117] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.093121] dwc2 c90c0000.usb: no split
[  238.093125] dwc2 c90c0000.usb: Wrote 4008001f to HCTSIZ(12)
[  238.093129] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 12
[  238.093133] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.093136] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.093140] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.093144] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(12)
[  238.093148] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.093152] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(12)
[  238.093162] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.093166] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.093169] dwc2 c90c0000.usb: HAINT=00001000
[  238.093173] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 12
[  238.093178] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.093182] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Channel Halted--
[  238.093186] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: DMA Channel Halted--
[  238.093190] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Transfer Complete--
[  238.093194] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.093198] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.093203] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 12
[  238.093206] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.093210] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.093213] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.093217] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.093221] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.093227] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.093232] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.093237] dwc2 c90c0000.usb:   dwc2_release_channel: channel 12, halt_status 2
[  238.093242] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.093246] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.093249] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.093254] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.093258] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.093291] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.093301] dwc2 c90c0000.usb: urb_enqueue, urb 64d8cdc0
[  238.093305] dwc2 c90c0000.usb:   Device address: 3
[  238.093308] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.093312] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.093316] dwc2 c90c0000.usb:   Speed: HIGH
[  238.093320] dwc2 c90c0000.usb:   Max packet size: 512
[  238.093323] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.093328] dwc2 c90c0000.usb:   Transfer buffer: ac21727a, Transfer DMA: 1fcef000
[  238.093332] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.093336] dwc2 c90c0000.usb:   Interval: 0
[  238.093342] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.093347] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.093355] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.093359] dwc2 c90c0000.usb: urb_enqueue, urb 544633e2
[  238.093363] dwc2 c90c0000.usb:   Device address: 3
[  238.093367] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.093371] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.093374] dwc2 c90c0000.usb:   Speed: HIGH
[  238.093377] dwc2 c90c0000.usb:   Max packet size: 512
[  238.093381] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.093385] dwc2 c90c0000.usb:   Transfer buffer: 4650d892, Transfer DMA: 1f8b4000
[  238.093390] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.093393] dwc2 c90c0000.usb:   Interval: 0
[  238.093399] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.093403] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.093423] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.093427] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.093431] dwc2 c90c0000.usb: DMA enabled
[  238.093434] dwc2 c90c0000.usb: desc DMA disabled
[  238.093438] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.093442] dwc2 c90c0000.usb: set HAINTMSK to 00002000
[  238.093446] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.093456] dwc2 c90c0000.usb: set HCCHAR(13) to 00c89200
[  238.093460] dwc2 c90c0000.usb: dwc2_hc_init: Channel 13
[  238.093463] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.093466] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.093470] dwc2 c90c0000.usb: 	 Is In: 1
[  238.093473] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.093477] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.093480] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.093484] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.093488] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.093492] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.093496] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.093499] dwc2 c90c0000.usb: no split
[  238.093504] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(13)
[  238.093507] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 13
[  238.093511] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.093515] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.093518] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.093522] dwc2 c90c0000.usb: Wrote 1fcef000 to HCDMA(13)
[  238.093526] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.093530] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(13)
[  238.093642] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.093646] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.093650] dwc2 c90c0000.usb: HAINT=00002000
[  238.093654] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 13
[  238.093659] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.093663] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Channel Halted--
[  238.093667] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: DMA Channel Halted--
[  238.093671] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Transfer Complete--
[  238.093674] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.093679] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.093683] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 13
[  238.093686] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.093690] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.093694] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.093697] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.093701] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.093707] dwc2 c90c0000.usb: dwc2_host_complete: urb 64d8cdc0 device 3 ep 2-IN status 0 actual 4096
[  238.093712] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.093716] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.093719] dwc2 c90c0000.usb: DMA enabled
[  238.093724] dwc2 c90c0000.usb:   dwc2_release_channel: channel 13, halt_status 2
[  238.093729] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.093733] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.093736] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.093739] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.093745] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.093749] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.093752] dwc2 c90c0000.usb: DMA enabled
[  238.093755] dwc2 c90c0000.usb: desc DMA disabled
[  238.093759] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.093763] dwc2 c90c0000.usb: set HAINTMSK to 00004000
[  238.093767] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.093771] dwc2 c90c0000.usb: set HCCHAR(14) to 00c89200
[  238.093775] dwc2 c90c0000.usb: dwc2_hc_init: Channel 14
[  238.093778] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.093781] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.093785] dwc2 c90c0000.usb: 	 Is In: 1
[  238.093788] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.093792] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.093795] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.093799] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.093803] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.093806] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.093810] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.093813] dwc2 c90c0000.usb: no split
[  238.093818] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(14)
[  238.093822] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 14
[  238.093825] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.093829] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.093832] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.093837] dwc2 c90c0000.usb: Wrote 1f8b4000 to HCDMA(14)
[  238.093840] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.093844] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(14)
[  238.093848] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.093853] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.093951] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.093956] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.093960] dwc2 c90c0000.usb: HAINT=00004000
[  238.093965] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 14
[  238.093970] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.093974] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Channel Halted--
[  238.093978] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: DMA Channel Halted--
[  238.093982] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Transfer Complete--
[  238.093986] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.093990] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.093996] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 14
[  238.093999] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.094003] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.094006] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.094010] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.094014] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.094020] dwc2 c90c0000.usb: dwc2_host_complete: urb 544633e2 device 3 ep 2-IN status 0 actual 4096
[  238.094026] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.094029] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.094033] dwc2 c90c0000.usb: DMA enabled
[  238.094037] dwc2 c90c0000.usb:   dwc2_release_channel: channel 14, halt_status 2
[  238.094042] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.094046] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.094050] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.094054] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.094059] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.094102] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.094108] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.094112] dwc2 c90c0000.usb:   Device address: 3
[  238.094116] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.094119] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.094123] dwc2 c90c0000.usb:   Speed: HIGH
[  238.094127] dwc2 c90c0000.usb:   Max packet size: 512
[  238.094131] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.094135] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.094140] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.094143] dwc2 c90c0000.usb:   Interval: 0
[  238.094149] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.094155] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.094176] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.094180] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.094184] dwc2 c90c0000.usb: DMA enabled
[  238.094187] dwc2 c90c0000.usb: desc DMA disabled
[  238.094191] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.094194] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[  238.094198] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.094203] dwc2 c90c0000.usb: set HCCHAR(0) to 00c89200
[  238.094207] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[  238.094210] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.094214] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.094217] dwc2 c90c0000.usb: 	 Is In: 1
[  238.094220] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.094224] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.094227] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.094231] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.094235] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.094239] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.094243] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.094246] dwc2 c90c0000.usb: no split
[  238.094251] dwc2 c90c0000.usb: Wrote 40080200 to HCTSIZ(0)
[  238.094255] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[  238.094259] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.094262] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.094266] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.094270] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(0)
[  238.094274] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.094279] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(0)
[  238.094300] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.094304] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.094308] dwc2 c90c0000.usb: HAINT=00000001
[  238.094312] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[  238.094317] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.094321] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Channel Halted--
[  238.094325] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: DMA Channel Halted--
[  238.094329] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Transfer Complete--
[  238.094333] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.094337] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.094342] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 0
[  238.094345] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.094349] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.094352] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.094356] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.094360] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.094366] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.094378] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.094382] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.094385] dwc2 c90c0000.usb: DMA enabled
[  238.094389] dwc2 c90c0000.usb:   dwc2_release_channel: channel 0, halt_status 2
[  238.094394] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.094398] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.094402] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.094407] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.094411] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.094514] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.094521] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.094525] dwc2 c90c0000.usb:   Device address: 3
[  238.094529] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.094533] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.094537] dwc2 c90c0000.usb:   Speed: HIGH
[  238.094547] dwc2 c90c0000.usb:   Max packet size: 512
[  238.094552] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.094557] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.094561] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.094565] dwc2 c90c0000.usb:   Interval: 0
[  238.094571] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.094576] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.094679] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.094685] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.094688] dwc2 c90c0000.usb: DMA enabled
[  238.094691] dwc2 c90c0000.usb: desc DMA disabled
[  238.094695] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.094699] dwc2 c90c0000.usb: set HAINTMSK to 00008000
[  238.094704] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.094708] dwc2 c90c0000.usb: set HCCHAR(15) to 00c80a00
[  238.094712] dwc2 c90c0000.usb: dwc2_hc_init: Channel 15
[  238.094715] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.094719] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.094722] dwc2 c90c0000.usb: 	 Is In: 0
[  238.094726] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.094730] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.094733] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.094737] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.094741] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.094745] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.094749] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.094752] dwc2 c90c0000.usb: no split
[  238.094757] dwc2 c90c0000.usb: Wrote 0008001f to HCTSIZ(15)
[  238.094761] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 15
[  238.094765] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.094768] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.094772] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.094776] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(15)
[  238.094780] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.094784] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(15)
[  238.094795] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000008
[  238.094799] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.094802] dwc2 c90c0000.usb: HAINT=00008000
[  238.094807] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 15
[  238.094811] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.094816] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Channel Halted--
[  238.094820] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: DMA Channel Halted--
[  238.094824] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Transfer Complete--
[  238.094828] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.094833] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.094837] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 15
[  238.094841] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.094844] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.094848] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.094851] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.094855] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.094862] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.094867] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.094872] dwc2 c90c0000.usb:   dwc2_release_channel: channel 15, halt_status 2
[  238.094877] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.094881] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.094884] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.094889] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.094894] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.094931] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.094938] dwc2 c90c0000.usb: urb_enqueue, urb 64d8cdc0
[  238.094942] dwc2 c90c0000.usb:   Device address: 3
[  238.094946] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.094949] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.094953] dwc2 c90c0000.usb:   Speed: HIGH
[  238.094957] dwc2 c90c0000.usb:   Max packet size: 512
[  238.094961] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.094966] dwc2 c90c0000.usb:   Transfer buffer: 0a625071, Transfer DMA: 1f8b5000
[  238.094971] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.094974] dwc2 c90c0000.usb:   Interval: 0
[  238.094980] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.094986] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.094998] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.095003] dwc2 c90c0000.usb: urb_enqueue, urb 544633e2
[  238.095006] dwc2 c90c0000.usb:   Device address: 3
[  238.095010] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.095014] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.095017] dwc2 c90c0000.usb:   Speed: HIGH
[  238.095021] dwc2 c90c0000.usb:   Max packet size: 512
[  238.095024] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.095029] dwc2 c90c0000.usb:   Transfer buffer: 0164470e, Transfer DMA: 2e78c000
[  238.095033] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.095036] dwc2 c90c0000.usb:   Interval: 0
[  238.095046] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.095050] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.095053] dwc2 c90c0000.usb: DMA enabled
[  238.095057] dwc2 c90c0000.usb: desc DMA disabled
[  238.095060] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.095064] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[  238.095068] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.095072] dwc2 c90c0000.usb: set HCCHAR(1) to 00c89200
[  238.095076] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[  238.095079] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.095083] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.095086] dwc2 c90c0000.usb: 	 Is In: 1
[  238.095090] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.095093] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.095096] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.095100] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.095104] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.095108] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.095112] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.095115] dwc2 c90c0000.usb: no split
[  238.095120] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(1)
[  238.095124] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[  238.095127] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.095130] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.095134] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.095138] dwc2 c90c0000.usb: Wrote 1f8b5000 to HCDMA(1)
[  238.095142] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.095146] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(1)
[  238.095153] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.095158] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.095172] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.095177] dwc2 c90c0000.usb: urb_enqueue, urb cd91f79f
[  238.095181] dwc2 c90c0000.usb:   Device address: 3
[  238.095184] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.095188] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.095192] dwc2 c90c0000.usb:   Speed: HIGH
[  238.095195] dwc2 c90c0000.usb:   Max packet size: 512
[  238.095199] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.095203] dwc2 c90c0000.usb:   Transfer buffer: a749ddf3, Transfer DMA: 2e74e000
[  238.095207] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.095211] dwc2 c90c0000.usb:   Interval: 0
[  238.095217] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.095221] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.095251] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.095256] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.095260] dwc2 c90c0000.usb: HAINT=00000002
[  238.095270] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[  238.095274] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.095279] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[  238.095283] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[  238.095287] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[  238.095291] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.095295] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.095300] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 1
[  238.095304] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.095307] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.095311] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.095314] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.095318] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.095325] dwc2 c90c0000.usb: dwc2_host_complete: urb 64d8cdc0 device 3 ep 2-IN status 0 actual 4096
[  238.095331] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.095334] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.095337] dwc2 c90c0000.usb: DMA enabled
[  238.095342] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 2
[  238.095347] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.095351] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.095354] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.095358] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.095363] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.095367] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.095371] dwc2 c90c0000.usb: DMA enabled
[  238.095374] dwc2 c90c0000.usb: desc DMA disabled
[  238.095378] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.095381] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[  238.095385] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.095389] dwc2 c90c0000.usb: set HCCHAR(2) to 00c89200
[  238.095393] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[  238.095397] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.095400] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.095403] dwc2 c90c0000.usb: 	 Is In: 1
[  238.095407] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.095410] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.095414] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.095418] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.095421] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.095425] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.095429] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.095432] dwc2 c90c0000.usb: no split
[  238.095437] dwc2 c90c0000.usb: Wrote 00802000 to HCTSIZ(2)
[  238.095441] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[  238.095444] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.095448] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.095451] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.095456] dwc2 c90c0000.usb: Wrote 2e78c000 to HCDMA(2)
[  238.095459] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.095464] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(2)
[  238.095468] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.095472] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.095757] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.095761] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.095765] dwc2 c90c0000.usb: HAINT=00000004
[  238.095769] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[  238.095774] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.095778] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[  238.095782] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[  238.095786] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[  238.095789] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.095793] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.095798] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 2
[  238.095801] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.095805] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.095808] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.095812] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.095816] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.095822] dwc2 c90c0000.usb: dwc2_host_complete: urb 544633e2 device 3 ep 2-IN status 0 actual 8192
[  238.095827] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.095831] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.095834] dwc2 c90c0000.usb: DMA enabled
[  238.095838] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 2
[  238.095843] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.095847] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.095850] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.095854] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.095859] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.095863] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.095866] dwc2 c90c0000.usb: DMA enabled
[  238.095869] dwc2 c90c0000.usb: desc DMA disabled
[  238.095873] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.095877] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[  238.095881] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.095885] dwc2 c90c0000.usb: set HCCHAR(3) to 00c89200
[  238.095889] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[  238.095892] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.095895] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.095899] dwc2 c90c0000.usb: 	 Is In: 1
[  238.095902] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.095906] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.095909] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.095913] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.095917] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.095921] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.095925] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.095928] dwc2 c90c0000.usb: no split
[  238.095933] dwc2 c90c0000.usb: Wrote 00401000 to HCTSIZ(3)
[  238.095937] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[  238.095940] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.095944] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.095947] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.095951] dwc2 c90c0000.usb: Wrote 2e74e000 to HCDMA(3)
[  238.095955] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.095959] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(3)
[  238.095963] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.095968] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.096060] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.096064] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.096073] dwc2 c90c0000.usb: HAINT=00000008
[  238.096077] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[  238.096081] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.096085] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[  238.096089] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[  238.096093] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[  238.096097] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.096101] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.096105] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 3
[  238.096109] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.096112] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.096116] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.096120] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.096123] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.096130] dwc2 c90c0000.usb: dwc2_host_complete: urb cd91f79f device 3 ep 2-IN status 0 actual 4096
[  238.096135] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.096138] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.096142] dwc2 c90c0000.usb: DMA enabled
[  238.096146] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 2
[  238.096151] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.096155] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.096158] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.096162] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.096167] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.096199] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.096205] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.096209] dwc2 c90c0000.usb:   Device address: 3
[  238.096212] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.096217] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.096220] dwc2 c90c0000.usb:   Speed: HIGH
[  238.096224] dwc2 c90c0000.usb:   Max packet size: 512
[  238.096228] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.096232] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.096236] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.096240] dwc2 c90c0000.usb:   Interval: 0
[  238.096246] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.096251] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.096299] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.096303] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.096307] dwc2 c90c0000.usb: DMA enabled
[  238.096310] dwc2 c90c0000.usb: desc DMA disabled
[  238.096314] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.096318] dwc2 c90c0000.usb: set HAINTMSK to 00000010
[  238.096322] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.096326] dwc2 c90c0000.usb: set HCCHAR(4) to 00c89200
[  238.096330] dwc2 c90c0000.usb: dwc2_hc_init: Channel 4
[  238.096334] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.096337] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.096340] dwc2 c90c0000.usb: 	 Is In: 1
[  238.096344] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.096347] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.096351] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.096354] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.096358] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.096362] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.096366] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.096369] dwc2 c90c0000.usb: no split
[  238.096374] dwc2 c90c0000.usb: Wrote 00080200 to HCTSIZ(4)
[  238.096377] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 4
[  238.096381] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.096384] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.096388] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.096392] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(4)
[  238.096396] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.096400] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(4)
[  238.096410] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.096414] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.096418] dwc2 c90c0000.usb: HAINT=00000010
[  238.096422] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 4
[  238.096427] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.096431] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Channel Halted--
[  238.096435] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: DMA Channel Halted--
[  238.096439] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Transfer Complete--
[  238.096442] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.096447] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.096451] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 4
[  238.096455] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.096459] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.096462] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.096466] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.096469] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.096476] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.096480] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.096484] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.096487] dwc2 c90c0000.usb: DMA enabled
[  238.096491] dwc2 c90c0000.usb:   dwc2_release_channel: channel 4, halt_status 2
[  238.096496] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.096500] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.096504] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.096508] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.096512] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.096627] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.096634] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.096638] dwc2 c90c0000.usb:   Device address: 3
[  238.096642] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.096646] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.096650] dwc2 c90c0000.usb:   Speed: HIGH
[  238.096654] dwc2 c90c0000.usb:   Max packet size: 512
[  238.096657] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.096662] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.096673] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.096677] dwc2 c90c0000.usb:   Interval: 0
[  238.096684] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.096688] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.096799] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.096804] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.096807] dwc2 c90c0000.usb: DMA enabled
[  238.096810] dwc2 c90c0000.usb: desc DMA disabled
[  238.096814] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.096818] dwc2 c90c0000.usb: set HAINTMSK to 00000040
[  238.096822] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.096826] dwc2 c90c0000.usb: set HCCHAR(6) to 00c80a00
[  238.096830] dwc2 c90c0000.usb: dwc2_hc_init: Channel 6
[  238.096833] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.096837] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.096840] dwc2 c90c0000.usb: 	 Is In: 0
[  238.096844] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.096847] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.096851] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.096855] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.096858] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.096862] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.096866] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.096870] dwc2 c90c0000.usb: no split
[  238.096874] dwc2 c90c0000.usb: Wrote 4008001f to HCTSIZ(6)
[  238.096884] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 6
[  238.096888] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.096891] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.096895] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.096899] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(6)
[  238.096903] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.096907] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(6)
[  238.096917] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.096921] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.096924] dwc2 c90c0000.usb: HAINT=00000040
[  238.096929] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 6
[  238.096933] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.096937] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Channel Halted--
[  238.096941] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: DMA Channel Halted--
[  238.096946] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Transfer Complete--
[  238.096949] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.096954] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.096958] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 6
[  238.096961] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.096965] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.096969] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.096972] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.096976] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.096982] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.096988] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.096993] dwc2 c90c0000.usb:   dwc2_release_channel: channel 6, halt_status 2
[  238.096998] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.097002] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.097006] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.097010] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.097015] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.097064] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.097070] dwc2 c90c0000.usb: urb_enqueue, urb 64d8cdc0
[  238.097074] dwc2 c90c0000.usb:   Device address: 3
[  238.097077] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.097081] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.097085] dwc2 c90c0000.usb:   Speed: HIGH
[  238.097089] dwc2 c90c0000.usb:   Max packet size: 512
[  238.097092] dwc2 c90c0000.usb:   Data buffer length: 4096
[  238.097097] dwc2 c90c0000.usb:   Transfer buffer: 3f7fe4fb, Transfer DMA: 2e74f000
[  238.097101] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.097105] dwc2 c90c0000.usb:   Interval: 0
[  238.097110] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.097115] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.097126] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.097130] dwc2 c90c0000.usb: urb_enqueue, urb 544633e2
[  238.097134] dwc2 c90c0000.usb:   Device address: 3
[  238.097137] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.097141] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.097145] dwc2 c90c0000.usb:   Speed: HIGH
[  238.097148] dwc2 c90c0000.usb:   Max packet size: 512
[  238.097152] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.097156] dwc2 c90c0000.usb:   Transfer buffer: fdcb3739, Transfer DMA: 2d324000
[  238.097161] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.097164] dwc2 c90c0000.usb:   Interval: 0
[  238.097172] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.097176] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.097179] dwc2 c90c0000.usb: DMA enabled
[  238.097182] dwc2 c90c0000.usb: desc DMA disabled
[  238.097186] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.097190] dwc2 c90c0000.usb: set HAINTMSK to 00000020
[  238.097194] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.097198] dwc2 c90c0000.usb: set HCCHAR(5) to 00c89200
[  238.097202] dwc2 c90c0000.usb: dwc2_hc_init: Channel 5
[  238.097205] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.097209] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.097212] dwc2 c90c0000.usb: 	 Is In: 1
[  238.097215] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.097219] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.097222] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.097226] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.097230] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.097234] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.097238] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.097241] dwc2 c90c0000.usb: no split
[  238.097246] dwc2 c90c0000.usb: Wrote 40401000 to HCTSIZ(5)
[  238.097249] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 5
[  238.097253] dwc2 c90c0000.usb: 	 Xfer Size: 4096
[  238.097256] dwc2 c90c0000.usb: 	 Num Pkts: 8
[  238.097260] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.097264] dwc2 c90c0000.usb: Wrote 2e74f000 to HCDMA(5)
[  238.097268] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.097272] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(5)
[  238.097281] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.097285] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.097299] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.097304] dwc2 c90c0000.usb: urb_enqueue, urb cd91f79f
[  238.097308] dwc2 c90c0000.usb:   Device address: 3
[  238.097311] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.097315] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.097319] dwc2 c90c0000.usb:   Speed: HIGH
[  238.097322] dwc2 c90c0000.usb:   Max packet size: 512
[  238.097326] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.097330] dwc2 c90c0000.usb:   Transfer buffer: a7951253, Transfer DMA: 2e79c000
[  238.097335] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.097338] dwc2 c90c0000.usb:   Interval: 0
[  238.097344] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.097348] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.097358] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.097363] dwc2 c90c0000.usb: urb_enqueue, urb 67466227
[  238.097366] dwc2 c90c0000.usb:   Device address: 3
[  238.097373] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.097377] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.097381] dwc2 c90c0000.usb: HAINT=00000020
[  238.097385] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 5
[  238.097389] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.097394] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Channel Halted--
[  238.097398] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: DMA Channel Halted--
[  238.097403] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Transfer Complete--
[  238.097406] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.097410] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=4096
[  238.097415] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 5
[  238.097418] dwc2 c90c0000.usb:   chan->xfer_len 4096
[  238.097422] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.097425] dwc2 c90c0000.usb:   urb->transfer_buffer_length 4096
[  238.097429] dwc2 c90c0000.usb:   urb->actual_length 4096
[  238.097433] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.097439] dwc2 c90c0000.usb: dwc2_host_complete: urb 64d8cdc0 device 3 ep 2-IN status 0 actual 4096
[  238.097444] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.097448] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.097451] dwc2 c90c0000.usb: DMA enabled
[  238.097456] dwc2 c90c0000.usb:   dwc2_release_channel: channel 5, halt_status 2
[  238.097461] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.097465] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.097468] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.097472] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.097477] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.097481] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.097484] dwc2 c90c0000.usb: DMA enabled
[  238.097488] dwc2 c90c0000.usb: desc DMA disabled
[  238.097491] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.097495] dwc2 c90c0000.usb: set HAINTMSK to 00000080
[  238.097499] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.097503] dwc2 c90c0000.usb: set HCCHAR(7) to 00c89200
[  238.097507] dwc2 c90c0000.usb: dwc2_hc_init: Channel 7
[  238.097510] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.097514] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.097517] dwc2 c90c0000.usb: 	 Is In: 1
[  238.097521] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.097524] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.097528] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.097532] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.097535] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.097539] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.097543] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.097546] dwc2 c90c0000.usb: no split
[  238.097551] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(7)
[  238.097554] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 7
[  238.097558] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.097562] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.097565] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.097569] dwc2 c90c0000.usb: Wrote 2d324000 to HCDMA(7)
[  238.097573] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.097577] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(7)
[  238.097582] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.097586] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.097603] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.097607] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.097611] dwc2 c90c0000.usb:   Speed: HIGH
[  238.097615] dwc2 c90c0000.usb:   Max packet size: 512
[  238.097619] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.097623] dwc2 c90c0000.usb:   Transfer buffer: 22641876, Transfer DMA: 1f8c2000
[  238.097628] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.097631] dwc2 c90c0000.usb:   Interval: 0
[  238.097637] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.097641] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.097654] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.097658] dwc2 c90c0000.usb: urb_enqueue, urb a7ce381f
[  238.097662] dwc2 c90c0000.usb:   Device address: 3
[  238.097670] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.097674] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.097678] dwc2 c90c0000.usb:   Speed: HIGH
[  238.097681] dwc2 c90c0000.usb:   Max packet size: 512
[  238.097685] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.097690] dwc2 c90c0000.usb:   Transfer buffer: 17255a67, Transfer DMA: 1faa0000
[  238.097700] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.097703] dwc2 c90c0000.usb:   Interval: 0
[  238.097708] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.097713] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.097724] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.097728] dwc2 c90c0000.usb: urb_enqueue, urb 5f70d834
[  238.097732] dwc2 c90c0000.usb:   Device address: 3
[  238.097736] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.097739] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.097743] dwc2 c90c0000.usb:   Speed: HIGH
[  238.097746] dwc2 c90c0000.usb:   Max packet size: 512
[  238.097750] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.097754] dwc2 c90c0000.usb:   Transfer buffer: 7d763a5d, Transfer DMA: 1f9ca000
[  238.097758] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.097762] dwc2 c90c0000.usb:   Interval: 0
[  238.097767] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.097771] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.097780] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.097785] dwc2 c90c0000.usb: urb_enqueue, urb c4a7e8a9
[  238.097788] dwc2 c90c0000.usb:   Device address: 3
[  238.097796] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.097800] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.097803] dwc2 c90c0000.usb:   Speed: HIGH
[  238.097807] dwc2 c90c0000.usb:   Max packet size: 512
[  238.097811] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.097816] dwc2 c90c0000.usb:   Transfer buffer: c5b71275, Transfer DMA: 1f8fc000
[  238.097820] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.097823] dwc2 c90c0000.usb:   Interval: 0
[  238.097828] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.097833] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.097842] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.097847] dwc2 c90c0000.usb: urb_enqueue, urb f8714879
[  238.097850] dwc2 c90c0000.usb:   Device address: 3
[  238.097854] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.097858] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.097861] dwc2 c90c0000.usb:   Speed: HIGH
[  238.097868] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.097872] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.097875] dwc2 c90c0000.usb: HAINT=00000080
[  238.097879] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 7
[  238.097884] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.097888] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Channel Halted--
[  238.097892] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: DMA Channel Halted--
[  238.097896] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Transfer Complete--
[  238.097900] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.097904] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.097909] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 7
[  238.097912] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.097916] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.097919] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.097923] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.097927] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.097933] dwc2 c90c0000.usb: dwc2_host_complete: urb 544633e2 device 3 ep 2-IN status 0 actual 8192
[  238.097938] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.097941] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.097944] dwc2 c90c0000.usb: DMA enabled
[  238.097949] dwc2 c90c0000.usb:   dwc2_release_channel: channel 7, halt_status 2
[  238.097954] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.097958] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.097961] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.097964] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.097969] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.097973] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.097976] dwc2 c90c0000.usb: DMA enabled
[  238.097980] dwc2 c90c0000.usb: desc DMA disabled
[  238.097983] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.097988] dwc2 c90c0000.usb: set HAINTMSK to 00000100
[  238.097992] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.097996] dwc2 c90c0000.usb: set HCCHAR(8) to 00c89200
[  238.098000] dwc2 c90c0000.usb: dwc2_hc_init: Channel 8
[  238.098003] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.098007] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.098010] dwc2 c90c0000.usb: 	 Is In: 1
[  238.098014] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.098017] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.098021] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.098025] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.098028] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.098032] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.098036] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.098039] dwc2 c90c0000.usb: no split
[  238.098044] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(8)
[  238.098047] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 8
[  238.098051] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.098054] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.098058] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.098062] dwc2 c90c0000.usb: Wrote 2e79c000 to HCDMA(8)
[  238.098066] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.098070] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(8)
[  238.098074] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.098079] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.098096] dwc2 c90c0000.usb:   Max packet size: 512
[  238.098100] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.098105] dwc2 c90c0000.usb:   Transfer buffer: df90cc4c, Transfer DMA: 2d298000
[  238.098110] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.098113] dwc2 c90c0000.usb:   Interval: 0
[  238.098119] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.098123] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.098135] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.098140] dwc2 c90c0000.usb: urb_enqueue, urb 9084c402
[  238.098144] dwc2 c90c0000.usb:   Device address: 3
[  238.098147] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.098151] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.098154] dwc2 c90c0000.usb:   Speed: HIGH
[  238.098158] dwc2 c90c0000.usb:   Max packet size: 512
[  238.098162] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.098171] dwc2 c90c0000.usb:   Transfer buffer: a1e9ab18, Transfer DMA: 2d2b0000
[  238.098176] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.098179] dwc2 c90c0000.usb:   Interval: 0
[  238.098185] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.098189] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.098345] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.098349] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.098353] dwc2 c90c0000.usb: HAINT=00000100
[  238.098357] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 8
[  238.098362] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.098366] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Channel Halted--
[  238.098370] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: DMA Channel Halted--
[  238.098374] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Transfer Complete--
[  238.098378] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.098382] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.098386] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 8
[  238.098390] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.098393] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.098397] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.098400] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.098404] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.098411] dwc2 c90c0000.usb: dwc2_host_complete: urb cd91f79f device 3 ep 2-IN status 0 actual 8192
[  238.098416] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.098419] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.098423] dwc2 c90c0000.usb: DMA enabled
[  238.098427] dwc2 c90c0000.usb:   dwc2_release_channel: channel 8, halt_status 2
[  238.098432] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.098436] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.098439] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.098442] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.098448] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.098452] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.098455] dwc2 c90c0000.usb: DMA enabled
[  238.098458] dwc2 c90c0000.usb: desc DMA disabled
[  238.098462] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.098469] dwc2 c90c0000.usb: set HAINTMSK to 00000200
[  238.098473] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.098477] dwc2 c90c0000.usb: set HCCHAR(9) to 00c89200
[  238.098481] dwc2 c90c0000.usb: dwc2_hc_init: Channel 9
[  238.098485] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.098488] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.098492] dwc2 c90c0000.usb: 	 Is In: 1
[  238.098495] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.098498] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.098502] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.098506] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.098510] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.098513] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.098517] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.098521] dwc2 c90c0000.usb: no split
[  238.098525] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(9)
[  238.098529] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 9
[  238.098532] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.098536] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.098540] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.098544] dwc2 c90c0000.usb: Wrote 1f8c2000 to HCDMA(9)
[  238.098548] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.098552] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(9)
[  238.098556] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.098560] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.098845] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.098849] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.098853] dwc2 c90c0000.usb: HAINT=00000200
[  238.098857] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 9
[  238.098861] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.098865] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Channel Halted--
[  238.098869] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: DMA Channel Halted--
[  238.098873] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Transfer Complete--
[  238.098877] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.098882] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.098886] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 9
[  238.098889] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.098893] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.098897] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.098900] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.098904] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.098911] dwc2 c90c0000.usb: dwc2_host_complete: urb 67466227 device 3 ep 2-IN status 0 actual 8192
[  238.098915] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.098919] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.098922] dwc2 c90c0000.usb: DMA enabled
[  238.098927] dwc2 c90c0000.usb:   dwc2_release_channel: channel 9, halt_status 2
[  238.098932] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.098935] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.098939] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.098942] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.098947] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.098951] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.098955] dwc2 c90c0000.usb: DMA enabled
[  238.098958] dwc2 c90c0000.usb: desc DMA disabled
[  238.098961] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.098965] dwc2 c90c0000.usb: set HAINTMSK to 00000400
[  238.098969] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.098973] dwc2 c90c0000.usb: set HCCHAR(10) to 00c89200
[  238.098977] dwc2 c90c0000.usb: dwc2_hc_init: Channel 10
[  238.098980] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.098984] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.098987] dwc2 c90c0000.usb: 	 Is In: 1
[  238.098991] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.098994] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.098998] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.099001] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.099006] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.099009] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.099013] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.099016] dwc2 c90c0000.usb: no split
[  238.099021] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(10)
[  238.099025] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 10
[  238.099028] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.099032] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.099035] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.099040] dwc2 c90c0000.usb: Wrote 1faa0000 to HCDMA(10)
[  238.099043] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.099048] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(10)
[  238.099051] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.099056] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.099321] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.099325] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.099329] dwc2 c90c0000.usb: HAINT=00000400
[  238.099333] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 10
[  238.099338] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.099342] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Channel Halted--
[  238.099346] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: DMA Channel Halted--
[  238.099350] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Transfer Complete--
[  238.099354] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.099358] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.099363] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 10
[  238.099366] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.099370] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.099373] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.099377] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.099381] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.099387] dwc2 c90c0000.usb: dwc2_host_complete: urb a7ce381f device 3 ep 2-IN status 0 actual 8192
[  238.099393] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.099396] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.099399] dwc2 c90c0000.usb: DMA enabled
[  238.099404] dwc2 c90c0000.usb:   dwc2_release_channel: channel 10, halt_status 2
[  238.099409] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.099413] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.099416] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.099419] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.099424] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.099428] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.099432] dwc2 c90c0000.usb: DMA enabled
[  238.099435] dwc2 c90c0000.usb: desc DMA disabled
[  238.099438] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.099442] dwc2 c90c0000.usb: set HAINTMSK to 00000800
[  238.099446] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.099450] dwc2 c90c0000.usb: set HCCHAR(11) to 00c89200
[  238.099454] dwc2 c90c0000.usb: dwc2_hc_init: Channel 11
[  238.099457] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.099461] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.099464] dwc2 c90c0000.usb: 	 Is In: 1
[  238.099468] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.099471] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.099475] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.099479] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.099482] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.099486] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.099490] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.099493] dwc2 c90c0000.usb: no split
[  238.099497] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(11)
[  238.099501] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 11
[  238.099505] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.099508] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.099512] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.099516] dwc2 c90c0000.usb: Wrote 1f9ca000 to HCDMA(11)
[  238.099520] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.099524] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(11)
[  238.099528] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.099532] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.099818] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.099823] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.099827] dwc2 c90c0000.usb: HAINT=00000800
[  238.099831] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 11
[  238.099836] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.099840] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Channel Halted--
[  238.099844] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: DMA Channel Halted--
[  238.099848] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Transfer Complete--
[  238.099851] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.099855] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.099860] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 11
[  238.099863] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.099867] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.099870] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.099874] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.099878] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.099884] dwc2 c90c0000.usb: dwc2_host_complete: urb 5f70d834 device 3 ep 2-IN status 0 actual 8192
[  238.099889] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.099893] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.099896] dwc2 c90c0000.usb: DMA enabled
[  238.099900] dwc2 c90c0000.usb:   dwc2_release_channel: channel 11, halt_status 2
[  238.099906] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.099909] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.099912] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.099916] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.099921] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.099925] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.099928] dwc2 c90c0000.usb: DMA enabled
[  238.099932] dwc2 c90c0000.usb: desc DMA disabled
[  238.099935] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.099939] dwc2 c90c0000.usb: set HAINTMSK to 00001000
[  238.099943] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.099947] dwc2 c90c0000.usb: set HCCHAR(12) to 00c89200
[  238.099951] dwc2 c90c0000.usb: dwc2_hc_init: Channel 12
[  238.099954] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.099958] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.099961] dwc2 c90c0000.usb: 	 Is In: 1
[  238.099965] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.099968] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.099972] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.099975] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.099979] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.099983] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.099987] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.099994] dwc2 c90c0000.usb: no split
[  238.099998] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(12)
[  238.100002] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 12
[  238.100005] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.100009] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.100013] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.100017] dwc2 c90c0000.usb: Wrote 1f8fc000 to HCDMA(12)
[  238.100021] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.100025] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(12)
[  238.100029] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.100033] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.100309] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.100313] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.100317] dwc2 c90c0000.usb: HAINT=00001000
[  238.100321] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 12
[  238.100326] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.100330] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Channel Halted--
[  238.100333] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: DMA Channel Halted--
[  238.100338] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Transfer Complete--
[  238.100341] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.100345] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.100350] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 12
[  238.100353] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.100357] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.100360] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.100364] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.100368] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.100374] dwc2 c90c0000.usb: dwc2_host_complete: urb c4a7e8a9 device 3 ep 2-IN status 0 actual 8192
[  238.100379] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.100382] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.100386] dwc2 c90c0000.usb: DMA enabled
[  238.100390] dwc2 c90c0000.usb:   dwc2_release_channel: channel 12, halt_status 2
[  238.100395] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.100399] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.100402] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.100406] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.100411] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.100415] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.100418] dwc2 c90c0000.usb: DMA enabled
[  238.100421] dwc2 c90c0000.usb: desc DMA disabled
[  238.100425] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.100429] dwc2 c90c0000.usb: set HAINTMSK to 00002000
[  238.100433] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.100437] dwc2 c90c0000.usb: set HCCHAR(13) to 00c89200
[  238.100441] dwc2 c90c0000.usb: dwc2_hc_init: Channel 13
[  238.100445] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.100448] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.100452] dwc2 c90c0000.usb: 	 Is In: 1
[  238.100455] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.100459] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.100462] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.100466] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.100470] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.100473] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.100477] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.100480] dwc2 c90c0000.usb: no split
[  238.100485] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(13)
[  238.100489] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 13
[  238.100492] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.100496] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.100500] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.100504] dwc2 c90c0000.usb: Wrote 2d298000 to HCDMA(13)
[  238.100508] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.100512] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(13)
[  238.100516] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.100520] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.100809] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.100813] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.100817] dwc2 c90c0000.usb: HAINT=00002000
[  238.100821] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 13
[  238.100825] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.100829] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Channel Halted--
[  238.100833] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: DMA Channel Halted--
[  238.100837] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Transfer Complete--
[  238.100841] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.100845] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.100850] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 13
[  238.100853] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.100857] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.100860] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.100864] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.100868] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.100874] dwc2 c90c0000.usb: dwc2_host_complete: urb f8714879 device 3 ep 2-IN status 0 actual 8192
[  238.100879] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.100882] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.100885] dwc2 c90c0000.usb: DMA enabled
[  238.100890] dwc2 c90c0000.usb:   dwc2_release_channel: channel 13, halt_status 2
[  238.100895] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.100899] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.100902] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.100905] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.100911] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.100914] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.100918] dwc2 c90c0000.usb: DMA enabled
[  238.100921] dwc2 c90c0000.usb: desc DMA disabled
[  238.100924] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.100928] dwc2 c90c0000.usb: set HAINTMSK to 00004000
[  238.100932] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.100936] dwc2 c90c0000.usb: set HCCHAR(14) to 00c89200
[  238.100940] dwc2 c90c0000.usb: dwc2_hc_init: Channel 14
[  238.100943] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.100947] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.100950] dwc2 c90c0000.usb: 	 Is In: 1
[  238.100954] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.100957] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.100961] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.100964] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.100968] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.100972] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.100975] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.100979] dwc2 c90c0000.usb: no split
[  238.100983] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(14)
[  238.100987] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 14
[  238.100990] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.100994] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.100997] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.101002] dwc2 c90c0000.usb: Wrote 2d2b0000 to HCDMA(14)
[  238.101005] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.101009] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(14)
[  238.101013] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.101018] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.101283] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.101288] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.101291] dwc2 c90c0000.usb: HAINT=00004000
[  238.101296] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 14
[  238.101300] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.101304] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Channel Halted--
[  238.101308] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: DMA Channel Halted--
[  238.101312] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Transfer Complete--
[  238.101316] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.101320] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.101324] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 14
[  238.101328] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.101331] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.101335] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.101339] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.101342] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.101349] dwc2 c90c0000.usb: dwc2_host_complete: urb 9084c402 device 3 ep 2-IN status 0 actual 8192
[  238.101353] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.101357] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.101361] dwc2 c90c0000.usb: DMA enabled
[  238.101365] dwc2 c90c0000.usb:   dwc2_release_channel: channel 14, halt_status 2
[  238.101370] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.101374] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.101377] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.101382] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.101386] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.101431] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.101438] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.101441] dwc2 c90c0000.usb:   Device address: 3
[  238.101445] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.101449] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.101453] dwc2 c90c0000.usb:   Speed: HIGH
[  238.101457] dwc2 c90c0000.usb:   Max packet size: 512
[  238.101460] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.101465] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.101469] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.101473] dwc2 c90c0000.usb:   Interval: 0
[  238.101479] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.101484] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.101549] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.101553] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.101557] dwc2 c90c0000.usb: DMA enabled
[  238.101560] dwc2 c90c0000.usb: desc DMA disabled
[  238.101564] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.101568] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[  238.101572] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.101576] dwc2 c90c0000.usb: set HCCHAR(0) to 00c89200
[  238.101580] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[  238.101583] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.101586] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.101590] dwc2 c90c0000.usb: 	 Is In: 1
[  238.101593] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.101597] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.101600] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.101605] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.101609] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.101612] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.101616] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.101620] dwc2 c90c0000.usb: no split
[  238.101624] dwc2 c90c0000.usb: Wrote 40080200 to HCTSIZ(0)
[  238.101628] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[  238.101632] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.101635] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.101639] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.101643] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(0)
[  238.101647] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.101651] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(0)
[  238.101661] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.101665] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.101669] dwc2 c90c0000.usb: HAINT=00000001
[  238.101673] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[  238.101677] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.101681] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Channel Halted--
[  238.101685] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: DMA Channel Halted--
[  238.101689] dwc2 c90c0000.usb: --Host Channel 0 Interrupt: Transfer Complete--
[  238.101693] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.101697] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.101702] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 0
[  238.101706] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.101709] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.101713] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.101716] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.101720] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.101726] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.101732] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.101735] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.101738] dwc2 c90c0000.usb: DMA enabled
[  238.101743] dwc2 c90c0000.usb:   dwc2_release_channel: channel 0, halt_status 2
[  238.101748] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.101751] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.101755] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.101760] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.101764] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.102136] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.102146] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.102150] dwc2 c90c0000.usb:   Device address: 3
[  238.102155] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.102159] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.102162] dwc2 c90c0000.usb:   Speed: HIGH
[  238.102174] dwc2 c90c0000.usb:   Max packet size: 512
[  238.102178] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.102183] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.102188] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.102191] dwc2 c90c0000.usb:   Interval: 0
[  238.102198] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.102205] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.102299] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.102304] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.102308] dwc2 c90c0000.usb: DMA enabled
[  238.102311] dwc2 c90c0000.usb: desc DMA disabled
[  238.102316] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.102320] dwc2 c90c0000.usb: set HAINTMSK to 00008000
[  238.102324] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.102328] dwc2 c90c0000.usb: set HCCHAR(15) to 00c80a00
[  238.102332] dwc2 c90c0000.usb: dwc2_hc_init: Channel 15
[  238.102336] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.102339] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.102343] dwc2 c90c0000.usb: 	 Is In: 0
[  238.102346] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.102349] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.102353] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.102357] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.102361] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.102364] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.102369] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.102372] dwc2 c90c0000.usb: no split
[  238.102382] dwc2 c90c0000.usb: Wrote 0008001f to HCTSIZ(15)
[  238.102386] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 15
[  238.102390] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.102393] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.102397] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.102401] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(15)
[  238.102405] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.102409] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(15)
[  238.102419] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000008
[  238.102424] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.102427] dwc2 c90c0000.usb: HAINT=00008000
[  238.102432] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 15
[  238.102436] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.102441] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Channel Halted--
[  238.102445] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: DMA Channel Halted--
[  238.102449] dwc2 c90c0000.usb: --Host Channel 15 Interrupt: Transfer Complete--
[  238.102453] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.102457] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.102462] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 15
[  238.102465] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.102469] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.102473] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.102476] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.102480] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.102487] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.102492] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.102497] dwc2 c90c0000.usb:   dwc2_release_channel: channel 15, halt_status 2
[  238.102502] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.102506] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.102510] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.102515] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.102519] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.102563] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.102569] dwc2 c90c0000.usb: urb_enqueue, urb 64d8cdc0
[  238.102573] dwc2 c90c0000.usb:   Device address: 3
[  238.102577] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.102581] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.102584] dwc2 c90c0000.usb:   Speed: HIGH
[  238.102588] dwc2 c90c0000.usb:   Max packet size: 512
[  238.102592] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.102596] dwc2 c90c0000.usb:   Transfer buffer: ccea0854, Transfer DMA: 2d2b4000
[  238.102601] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.102604] dwc2 c90c0000.usb:   Interval: 0
[  238.102610] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.102615] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.102624] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.102628] dwc2 c90c0000.usb: urb_enqueue, urb 544633e2
[  238.102632] dwc2 c90c0000.usb:   Device address: 3
[  238.102635] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.102639] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.102643] dwc2 c90c0000.usb:   Speed: HIGH
[  238.102646] dwc2 c90c0000.usb:   Max packet size: 512
[  238.102650] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.102654] dwc2 c90c0000.usb:   Transfer buffer: 1bbb216f, Transfer DMA: 1fb22000
[  238.102658] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.102662] dwc2 c90c0000.usb:   Interval: 0
[  238.102671] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.102675] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.102679] dwc2 c90c0000.usb: DMA enabled
[  238.102682] dwc2 c90c0000.usb: desc DMA disabled
[  238.102686] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.102690] dwc2 c90c0000.usb: set HAINTMSK to 00000002
[  238.102693] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.102698] dwc2 c90c0000.usb: set HCCHAR(1) to 00c89200
[  238.102701] dwc2 c90c0000.usb: dwc2_hc_init: Channel 1
[  238.102705] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.102708] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.102712] dwc2 c90c0000.usb: 	 Is In: 1
[  238.102715] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.102719] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.102722] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.102726] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.102730] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.102734] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.102738] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.102741] dwc2 c90c0000.usb: no split
[  238.102745] dwc2 c90c0000.usb: Wrote 00802000 to HCTSIZ(1)
[  238.102749] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 1
[  238.102753] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.102756] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.102760] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.102764] dwc2 c90c0000.usb: Wrote 2d2b4000 to HCDMA(1)
[  238.102768] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.102772] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(1)
[  238.102779] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.102783] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.103075] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.103080] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.103083] dwc2 c90c0000.usb: HAINT=00000002
[  238.103088] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 1
[  238.103093] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.103097] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Channel Halted--
[  238.103101] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: DMA Channel Halted--
[  238.103105] dwc2 c90c0000.usb: --Host Channel 1 Interrupt: Transfer Complete--
[  238.103109] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.103113] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.103118] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 1
[  238.103121] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.103125] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.103129] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.103132] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.103136] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.103143] dwc2 c90c0000.usb: dwc2_host_complete: urb 64d8cdc0 device 3 ep 2-IN status 0 actual 8192
[  238.103148] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.103152] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.103155] dwc2 c90c0000.usb: DMA enabled
[  238.103160] dwc2 c90c0000.usb:   dwc2_release_channel: channel 1, halt_status 2
[  238.103165] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.103169] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.103173] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.103176] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.103182] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.103186] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.103189] dwc2 c90c0000.usb: DMA enabled
[  238.103192] dwc2 c90c0000.usb: desc DMA disabled
[  238.103196] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.103200] dwc2 c90c0000.usb: set HAINTMSK to 00000004
[  238.103203] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.103208] dwc2 c90c0000.usb: set HCCHAR(2) to 00c89200
[  238.103211] dwc2 c90c0000.usb: dwc2_hc_init: Channel 2
[  238.103221] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.103224] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.103227] dwc2 c90c0000.usb: 	 Is In: 1
[  238.103231] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.103234] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.103238] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.103241] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.103245] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.103249] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.103253] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.103256] dwc2 c90c0000.usb: no split
[  238.103261] dwc2 c90c0000.usb: Wrote 00802000 to HCTSIZ(2)
[  238.103264] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 2
[  238.103268] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.103272] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.103275] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.103279] dwc2 c90c0000.usb: Wrote 1fb22000 to HCDMA(2)
[  238.103283] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.103288] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(2)
[  238.103292] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.103296] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.103598] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.103602] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.103606] dwc2 c90c0000.usb: HAINT=00000004
[  238.103610] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 2
[  238.103615] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.103619] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Channel Halted--
[  238.103623] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: DMA Channel Halted--
[  238.103627] dwc2 c90c0000.usb: --Host Channel 2 Interrupt: Transfer Complete--
[  238.103631] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.103635] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.103640] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 2
[  238.103643] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.103647] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.103651] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.103654] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.103658] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.103665] dwc2 c90c0000.usb: dwc2_host_complete: urb 544633e2 device 3 ep 2-IN status 0 actual 8192
[  238.103670] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.103673] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.103676] dwc2 c90c0000.usb: DMA enabled
[  238.103681] dwc2 c90c0000.usb:   dwc2_release_channel: channel 2, halt_status 2
[  238.103686] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.103690] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.103693] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.103698] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.103702] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.103737] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.103743] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.103746] dwc2 c90c0000.usb:   Device address: 3
[  238.103750] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.103754] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.103757] dwc2 c90c0000.usb:   Speed: HIGH
[  238.103762] dwc2 c90c0000.usb:   Max packet size: 512
[  238.103765] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.103770] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.103774] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.103778] dwc2 c90c0000.usb:   Interval: 0
[  238.103784] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.103789] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.103800] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.103804] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.103808] dwc2 c90c0000.usb: DMA enabled
[  238.103811] dwc2 c90c0000.usb: desc DMA disabled
[  238.103815] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.103819] dwc2 c90c0000.usb: set HAINTMSK to 00000008
[  238.103823] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.103827] dwc2 c90c0000.usb: set HCCHAR(3) to 00c89200
[  238.103831] dwc2 c90c0000.usb: dwc2_hc_init: Channel 3
[  238.103835] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.103838] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.103842] dwc2 c90c0000.usb: 	 Is In: 1
[  238.103845] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.103848] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.103852] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.103856] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.103860] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.103864] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.103868] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.103871] dwc2 c90c0000.usb: no split
[  238.103875] dwc2 c90c0000.usb: Wrote 00080200 to HCTSIZ(3)
[  238.103879] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 3
[  238.103883] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.103886] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.103890] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.103894] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(3)
[  238.103898] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.103902] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(3)
[  238.103933] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000008
[  238.103939] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.103942] dwc2 c90c0000.usb: HAINT=00000008
[  238.103947] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 3
[  238.103951] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.103955] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Channel Halted--
[  238.103959] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: DMA Channel Halted--
[  238.103964] dwc2 c90c0000.usb: --Host Channel 3 Interrupt: Transfer Complete--
[  238.103968] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.103972] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.103976] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 3
[  238.103980] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.103984] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.103987] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.103991] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.103995] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.104002] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.104008] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.104011] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.104015] dwc2 c90c0000.usb: DMA enabled
[  238.104019] dwc2 c90c0000.usb:   dwc2_release_channel: channel 3, halt_status 2
[  238.104025] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.104029] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.104032] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.104037] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.104041] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.104183] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.104190] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.104195] dwc2 c90c0000.usb:   Device address: 3
[  238.104199] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.104203] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.104206] dwc2 c90c0000.usb:   Speed: HIGH
[  238.104210] dwc2 c90c0000.usb:   Max packet size: 512
[  238.104214] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.104218] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.104223] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.104226] dwc2 c90c0000.usb:   Interval: 0
[  238.104233] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.104239] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.104300] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.104304] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.104308] dwc2 c90c0000.usb: DMA enabled
[  238.104311] dwc2 c90c0000.usb: desc DMA disabled
[  238.104315] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.104319] dwc2 c90c0000.usb: set HAINTMSK to 00000010
[  238.104323] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.104327] dwc2 c90c0000.usb: set HCCHAR(4) to 00c80a00
[  238.104331] dwc2 c90c0000.usb: dwc2_hc_init: Channel 4
[  238.104334] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.104337] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.104341] dwc2 c90c0000.usb: 	 Is In: 0
[  238.104344] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.104348] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.104352] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.104355] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.104359] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.104363] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.104367] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.104370] dwc2 c90c0000.usb: no split
[  238.104375] dwc2 c90c0000.usb: Wrote 4008001f to HCTSIZ(4)
[  238.104379] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 4
[  238.104383] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.104386] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.104390] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.104395] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(4)
[  238.104398] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.104402] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(4)
[  238.104413] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.104417] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.104421] dwc2 c90c0000.usb: HAINT=00000010
[  238.104425] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 4
[  238.104430] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.104434] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Channel Halted--
[  238.104437] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: DMA Channel Halted--
[  238.104441] dwc2 c90c0000.usb: --Host Channel 4 Interrupt: Transfer Complete--
[  238.104445] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.104450] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.104454] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 4
[  238.104458] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.104461] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.104465] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.104468] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.104472] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.104478] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.104484] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.104489] dwc2 c90c0000.usb:   dwc2_release_channel: channel 4, halt_status 2
[  238.104494] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.104498] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.104502] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.104507] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.104511] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.104560] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.104566] dwc2 c90c0000.usb: urb_enqueue, urb 64d8cdc0
[  238.104569] dwc2 c90c0000.usb:   Device address: 3
[  238.104573] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.104577] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.104581] dwc2 c90c0000.usb:   Speed: HIGH
[  238.104585] dwc2 c90c0000.usb:   Max packet size: 512
[  238.104588] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.104593] dwc2 c90c0000.usb:   Transfer buffer: b4350166, Transfer DMA: 1fe2c000
[  238.104598] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.104601] dwc2 c90c0000.usb:   Interval: 0
[  238.104607] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.104612] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.104623] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.104627] dwc2 c90c0000.usb: urb_enqueue, urb 544633e2
[  238.104631] dwc2 c90c0000.usb:   Device address: 3
[  238.104634] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.104638] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.104642] dwc2 c90c0000.usb:   Speed: HIGH
[  238.104645] dwc2 c90c0000.usb:   Max packet size: 512
[  238.104649] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.104653] dwc2 c90c0000.usb:   Transfer buffer: 696fd344, Transfer DMA: 1fe0c000
[  238.104658] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.104661] dwc2 c90c0000.usb:   Interval: 0
[  238.104671] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.104676] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.104679] dwc2 c90c0000.usb: DMA enabled
[  238.104682] dwc2 c90c0000.usb: desc DMA disabled
[  238.104686] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.104690] dwc2 c90c0000.usb: set HAINTMSK to 00000040
[  238.104694] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.104698] dwc2 c90c0000.usb: set HCCHAR(6) to 00c89200
[  238.104702] dwc2 c90c0000.usb: dwc2_hc_init: Channel 6
[  238.104706] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.104709] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.104712] dwc2 c90c0000.usb: 	 Is In: 1
[  238.104716] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.104719] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.104723] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.104727] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.104731] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.104734] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.104739] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.104742] dwc2 c90c0000.usb: no split
[  238.104747] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(6)
[  238.104751] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 6
[  238.104754] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.104758] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.104761] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.104765] dwc2 c90c0000.usb: Wrote 1fe2c000 to HCDMA(6)
[  238.104769] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.104773] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(6)
[  238.104779] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.104784] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.104798] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.104803] dwc2 c90c0000.usb: urb_enqueue, urb cd91f79f
[  238.104806] dwc2 c90c0000.usb:   Device address: 3
[  238.104810] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.104814] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.104817] dwc2 c90c0000.usb:   Speed: HIGH
[  238.104821] dwc2 c90c0000.usb:   Max packet size: 512
[  238.104825] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.104830] dwc2 c90c0000.usb:   Transfer buffer: 61e13010, Transfer DMA: 1fe7c000
[  238.104834] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.104838] dwc2 c90c0000.usb:   Interval: 0
[  238.104843] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.104847] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.105060] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.105065] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.105068] dwc2 c90c0000.usb: HAINT=00000040
[  238.105072] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 6
[  238.105077] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.105081] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Channel Halted--
[  238.105085] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: DMA Channel Halted--
[  238.105090] dwc2 c90c0000.usb: --Host Channel 6 Interrupt: Transfer Complete--
[  238.105093] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.105098] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.105102] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 6
[  238.105106] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.105109] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.105113] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.105116] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.105120] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.105127] dwc2 c90c0000.usb: dwc2_host_complete: urb 64d8cdc0 device 3 ep 2-IN status 0 actual 8192
[  238.105133] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.105137] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.105140] dwc2 c90c0000.usb: DMA enabled
[  238.105144] dwc2 c90c0000.usb:   dwc2_release_channel: channel 6, halt_status 2
[  238.105150] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.105154] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.105157] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.105161] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.105167] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.105171] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.105174] dwc2 c90c0000.usb: DMA enabled
[  238.105177] dwc2 c90c0000.usb: desc DMA disabled
[  238.105181] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.105185] dwc2 c90c0000.usb: set HAINTMSK to 00000020
[  238.105189] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.105193] dwc2 c90c0000.usb: set HCCHAR(5) to 00c89200
[  238.105197] dwc2 c90c0000.usb: dwc2_hc_init: Channel 5
[  238.105201] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.105204] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.105207] dwc2 c90c0000.usb: 	 Is In: 1
[  238.105211] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.105214] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.105218] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.105222] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.105225] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.105229] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.105233] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.105237] dwc2 c90c0000.usb: no split
[  238.105241] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(5)
[  238.105245] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 5
[  238.105249] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.105252] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.105256] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.105260] dwc2 c90c0000.usb: Wrote 1fe0c000 to HCDMA(5)
[  238.105264] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.105268] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(5)
[  238.105272] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.105277] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.105569] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.105573] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.105577] dwc2 c90c0000.usb: HAINT=00000020
[  238.105581] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 5
[  238.105586] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.105590] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Channel Halted--
[  238.105594] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: DMA Channel Halted--
[  238.105598] dwc2 c90c0000.usb: --Host Channel 5 Interrupt: Transfer Complete--
[  238.105601] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.105606] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.105610] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 5
[  238.105614] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.105617] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.105621] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.105624] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.105628] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.105635] dwc2 c90c0000.usb: dwc2_host_complete: urb 544633e2 device 3 ep 2-IN status 0 actual 8192
[  238.105640] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.105643] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.105647] dwc2 c90c0000.usb: DMA enabled
[  238.105651] dwc2 c90c0000.usb:   dwc2_release_channel: channel 5, halt_status 2
[  238.105656] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.105659] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.105663] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.105666] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.105672] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.105676] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.105679] dwc2 c90c0000.usb: DMA enabled
[  238.105682] dwc2 c90c0000.usb: desc DMA disabled
[  238.105686] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.105690] dwc2 c90c0000.usb: set HAINTMSK to 00000080
[  238.105694] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.105698] dwc2 c90c0000.usb: set HCCHAR(7) to 00c89200
[  238.105702] dwc2 c90c0000.usb: dwc2_hc_init: Channel 7
[  238.105705] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.105709] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.105712] dwc2 c90c0000.usb: 	 Is In: 1
[  238.105715] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.105719] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.105723] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.105726] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.105730] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.105734] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.105738] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.105741] dwc2 c90c0000.usb: no split
[  238.105746] dwc2 c90c0000.usb: Wrote 40802000 to HCTSIZ(7)
[  238.105750] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 7
[  238.105753] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.105757] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.105760] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.105764] dwc2 c90c0000.usb: Wrote 1fe7c000 to HCDMA(7)
[  238.105768] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.105772] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(7)
[  238.105776] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.105781] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.106059] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.106064] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.106067] dwc2 c90c0000.usb: HAINT=00000080
[  238.106071] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 7
[  238.106076] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.106080] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Channel Halted--
[  238.106084] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: DMA Channel Halted--
[  238.106088] dwc2 c90c0000.usb: --Host Channel 7 Interrupt: Transfer Complete--
[  238.106091] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.106096] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.106100] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 7
[  238.106104] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.106107] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.106111] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.106114] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.106118] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.106124] dwc2 c90c0000.usb: dwc2_host_complete: urb cd91f79f device 3 ep 2-IN status 0 actual 8192
[  238.106130] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.106133] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.106136] dwc2 c90c0000.usb: DMA enabled
[  238.106141] dwc2 c90c0000.usb:   dwc2_release_channel: channel 7, halt_status 2
[  238.106146] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.106150] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.106153] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.106157] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.106161] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.106203] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.106209] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.106213] dwc2 c90c0000.usb:   Device address: 3
[  238.106217] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.106221] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.106224] dwc2 c90c0000.usb:   Speed: HIGH
[  238.106228] dwc2 c90c0000.usb:   Max packet size: 512
[  238.106232] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.106236] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.106240] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.106244] dwc2 c90c0000.usb:   Interval: 0
[  238.106250] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.106255] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.106299] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.106304] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.106308] dwc2 c90c0000.usb: DMA enabled
[  238.106311] dwc2 c90c0000.usb: desc DMA disabled
[  238.106315] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.106319] dwc2 c90c0000.usb: set HAINTMSK to 00000100
[  238.106323] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.106327] dwc2 c90c0000.usb: set HCCHAR(8) to 00c89200
[  238.106330] dwc2 c90c0000.usb: dwc2_hc_init: Channel 8
[  238.106334] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.106337] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.106341] dwc2 c90c0000.usb: 	 Is In: 1
[  238.106344] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.106348] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.106351] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.106355] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.106359] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.106363] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.106367] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.106370] dwc2 c90c0000.usb: no split
[  238.106375] dwc2 c90c0000.usb: Wrote 40080200 to HCTSIZ(8)
[  238.106379] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 8
[  238.106382] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.106386] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.106389] dwc2 c90c0000.usb: 	 Start PID: 2
[  238.106393] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(8)
[  238.106397] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.106401] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(8)
[  238.106411] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.106415] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.106419] dwc2 c90c0000.usb: HAINT=00000100
[  238.106423] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 8
[  238.106427] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.106431] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Channel Halted--
[  238.106435] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: DMA Channel Halted--
[  238.106439] dwc2 c90c0000.usb: --Host Channel 8 Interrupt: Transfer Complete--
[  238.106443] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.106447] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=13
[  238.106452] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 8
[  238.106455] dwc2 c90c0000.usb:   chan->xfer_len 512
[  238.106459] dwc2 c90c0000.usb:   hctsiz.xfersize 499
[  238.106462] dwc2 c90c0000.usb:   urb->transfer_buffer_length 13
[  238.106466] dwc2 c90c0000.usb:   urb->actual_length 13
[  238.106470] dwc2 c90c0000.usb:   short_read 1, xfer_done 1
[  238.106476] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 2-IN status 0 actual 13
[  238.106480] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.106484] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.106487] dwc2 c90c0000.usb: DMA enabled
[  238.106492] dwc2 c90c0000.usb:   dwc2_release_channel: channel 8, halt_status 2
[  238.106497] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.106501] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.106504] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.106509] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.106514] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000029 gintmsk=0xf300000e
[  238.106615] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.106622] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.106626] dwc2 c90c0000.usb:   Device address: 3
[  238.106630] dwc2 c90c0000.usb:   Endpoint: 1, OUT
[  238.106634] dwc2 c90c0000.usb:   Endpoint type: BULK OUT (OUT)
[  238.106638] dwc2 c90c0000.usb:   Speed: HIGH
[  238.106642] dwc2 c90c0000.usb:   Max packet size: 512
[  238.106645] dwc2 c90c0000.usb:   Data buffer length: 31
[  238.106650] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.106654] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.106658] dwc2 c90c0000.usb:   Interval: 0
[  238.106665] dwc2 c90c0000.usb: addr=3, ep_num=1, ep_dir=0, ep_type=2, mps=512
[  238.106676] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.106803] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,8e43fde5)
[  238.106808] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.106812] dwc2 c90c0000.usb: DMA enabled
[  238.106815] dwc2 c90c0000.usb: desc DMA disabled
[  238.106819] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.106823] dwc2 c90c0000.usb: set HAINTMSK to 00000200
[  238.106827] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.106831] dwc2 c90c0000.usb: set HCCHAR(9) to 00c80a00
[  238.106835] dwc2 c90c0000.usb: dwc2_hc_init: Channel 9
[  238.106838] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.106842] dwc2 c90c0000.usb: 	 Ep Num: 1
[  238.106845] dwc2 c90c0000.usb: 	 Is In: 0
[  238.106849] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.106852] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.106856] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.106860] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.106864] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.106867] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.106872] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.106875] dwc2 c90c0000.usb: no split
[  238.106880] dwc2 c90c0000.usb: Wrote 0008001f to HCTSIZ(9)
[  238.106884] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 9
[  238.106887] dwc2 c90c0000.usb: 	 Xfer Size: 31
[  238.106891] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.106894] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.106899] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(9)
[  238.106902] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.106907] dwc2 c90c0000.usb: Wrote 80d80a00 to HCCHAR(9)
[  238.106918] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000008
[  238.106923] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.106926] dwc2 c90c0000.usb: HAINT=00000200
[  238.106931] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 9
[  238.106936] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.106940] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Channel Halted--
[  238.106944] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: DMA Channel Halted--
[  238.106948] dwc2 c90c0000.usb: --Host Channel 9 Interrupt: Transfer Complete--
[  238.106952] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.106957] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=31
[  238.106961] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: OUT, channel 9
[  238.106965] dwc2 c90c0000.usb:   chan->xfer_len 31
[  238.106968] dwc2 c90c0000.usb:   hctsiz.xfersize 31
[  238.106972] dwc2 c90c0000.usb:   urb->transfer_buffer_length 31
[  238.106975] dwc2 c90c0000.usb:   urb->actual_length 31
[  238.106979] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.106985] dwc2 c90c0000.usb: dwc2_host_complete: urb 45b274b6 device 3 ep 1-OUT status 0 actual 31
[  238.106991] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.106996] dwc2 c90c0000.usb:   dwc2_release_channel: channel 9, halt_status 2
[  238.107002] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,8e43fde5,1)
[  238.107005] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.107009] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.107014] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.107019] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.107066] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.107071] dwc2 c90c0000.usb: urb_enqueue, urb 64d8cdc0
[  238.107075] dwc2 c90c0000.usb:   Device address: 3
[  238.107079] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.107083] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.107087] dwc2 c90c0000.usb:   Speed: HIGH
[  238.107091] dwc2 c90c0000.usb:   Max packet size: 512
[  238.107094] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.107099] dwc2 c90c0000.usb:   Transfer buffer: 8460225b, Transfer DMA: 1fc08000
[  238.107104] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.107107] dwc2 c90c0000.usb:   Interval: 0
[  238.107113] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.107119] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.107130] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.107135] dwc2 c90c0000.usb: urb_enqueue, urb 544633e2
[  238.107138] dwc2 c90c0000.usb:   Device address: 3
[  238.107142] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.107145] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.107149] dwc2 c90c0000.usb:   Speed: HIGH
[  238.107152] dwc2 c90c0000.usb:   Max packet size: 512
[  238.107156] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.107161] dwc2 c90c0000.usb:   Transfer buffer: 413321d1, Transfer DMA: 1fbd4000
[  238.107165] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.107173] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.107177] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.107181] dwc2 c90c0000.usb: DMA enabled
[  238.107184] dwc2 c90c0000.usb: desc DMA disabled
[  238.107187] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.107191] dwc2 c90c0000.usb: set HAINTMSK to 00000400
[  238.107195] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.107199] dwc2 c90c0000.usb: set HCCHAR(10) to 00c89200
[  238.107203] dwc2 c90c0000.usb: dwc2_hc_init: Channel 10
[  238.107207] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.107210] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.107213] dwc2 c90c0000.usb: 	 Is In: 1
[  238.107217] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.107221] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.107224] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.107228] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.107232] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.107235] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.107240] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.107243] dwc2 c90c0000.usb: no split
[  238.107247] dwc2 c90c0000.usb: Wrote 00802000 to HCTSIZ(10)
[  238.107251] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 10
[  238.107255] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.107258] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.107262] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.107266] dwc2 c90c0000.usb: Wrote 1fc08000 to HCDMA(10)
[  238.107270] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.107274] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(10)
[  238.107280] dwc2 c90c0000.usb:   Interval: 0
[  238.107286] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.107291] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.107304] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.107309] dwc2 c90c0000.usb: urb_enqueue, urb cd91f79f
[  238.107313] dwc2 c90c0000.usb:   Device address: 3
[  238.107316] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.107320] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.107324] dwc2 c90c0000.usb:   Speed: HIGH
[  238.107327] dwc2 c90c0000.usb:   Max packet size: 512
[  238.107331] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.107335] dwc2 c90c0000.usb:   Transfer buffer: 3ef5705a, Transfer DMA: 1fd52000
[  238.107340] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.107343] dwc2 c90c0000.usb:   Interval: 0
[  238.107349] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.107353] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.107362] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.107366] dwc2 c90c0000.usb: urb_enqueue, urb 67466227
[  238.107370] dwc2 c90c0000.usb:   Device address: 3
[  238.107374] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.107377] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.107381] dwc2 c90c0000.usb:   Speed: HIGH
[  238.107384] dwc2 c90c0000.usb:   Max packet size: 512
[  238.107388] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.107392] dwc2 c90c0000.usb:   Transfer buffer: 58065908, Transfer DMA: 1fe20000
[  238.107396] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.107400] dwc2 c90c0000.usb:   Interval: 0
[  238.107405] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.107409] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.107423] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.107428] dwc2 c90c0000.usb: urb_enqueue, urb a7ce381f
[  238.107431] dwc2 c90c0000.usb:   Device address: 3
[  238.107435] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.107439] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.107442] dwc2 c90c0000.usb:   Speed: HIGH
[  238.107446] dwc2 c90c0000.usb:   Max packet size: 512
[  238.107450] dwc2 c90c0000.usb:   Data buffer length: 8192
[  238.107454] dwc2 c90c0000.usb:   Transfer buffer: f1cafc5f, Transfer DMA: 1fc72000
[  238.107458] dwc2 c90c0000.usb:   Setup buffer:   (null), Setup DMA: 00000000
[  238.107462] dwc2 c90c0000.usb:   Interval: 0
[  238.107467] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.107471] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.107571] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.107576] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.107580] dwc2 c90c0000.usb: HAINT=00000400
[  238.107584] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 10
[  238.107589] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.107593] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Channel Halted--
[  238.107597] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: DMA Channel Halted--
[  238.107602] dwc2 c90c0000.usb: --Host Channel 10 Interrupt: Transfer Complete--
[  238.107605] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.107610] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.107614] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 10
[  238.107618] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.107621] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.107625] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.107629] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.107633] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.107639] dwc2 c90c0000.usb: dwc2_host_complete: urb 64d8cdc0 device 3 ep 2-IN status 0 actual 8192
[  238.107644] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.107648] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.107651] dwc2 c90c0000.usb: DMA enabled
[  238.107656] dwc2 c90c0000.usb:   dwc2_release_channel: channel 10, halt_status 2
[  238.107661] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.107665] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.107669] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.107672] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.107678] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.107682] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.107686] dwc2 c90c0000.usb: DMA enabled
[  238.107689] dwc2 c90c0000.usb: desc DMA disabled
[  238.107693] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.107696] dwc2 c90c0000.usb: set HAINTMSK to 00000800
[  238.107700] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.107705] dwc2 c90c0000.usb: set HCCHAR(11) to 00c89200
[  238.107708] dwc2 c90c0000.usb: dwc2_hc_init: Channel 11
[  238.107712] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.107715] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.107719] dwc2 c90c0000.usb: 	 Is In: 1
[  238.107722] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.107726] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.107730] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.107733] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.107737] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.107741] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.107745] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.107748] dwc2 c90c0000.usb: no split
[  238.107753] dwc2 c90c0000.usb: Wrote 00802000 to HCTSIZ(11)
[  238.107757] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 11
[  238.107760] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.107764] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.107767] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.107771] dwc2 c90c0000.usb: Wrote 1fbd4000 to HCDMA(11)
[  238.107775] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.107779] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(11)
[  238.107783] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.107788] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.108069] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.108073] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.108077] dwc2 c90c0000.usb: HAINT=00000800
[  238.108081] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 11
[  238.108086] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.108090] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Channel Halted--
[  238.108094] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: DMA Channel Halted--
[  238.108098] dwc2 c90c0000.usb: --Host Channel 11 Interrupt: Transfer Complete--
[  238.108102] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.108106] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.108111] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 11
[  238.108114] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.108118] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.108121] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.108125] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.108129] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.108135] dwc2 c90c0000.usb: dwc2_host_complete: urb 544633e2 device 3 ep 2-IN status 0 actual 8192
[  238.108140] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.108143] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.108147] dwc2 c90c0000.usb: DMA enabled
[  238.108151] dwc2 c90c0000.usb:   dwc2_release_channel: channel 11, halt_status 2
[  238.108156] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.108160] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.108163] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.108166] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.108172] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.108175] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.108179] dwc2 c90c0000.usb: DMA enabled
[  238.108182] dwc2 c90c0000.usb: desc DMA disabled
[  238.108186] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.108189] dwc2 c90c0000.usb: set HAINTMSK to 00001000
[  238.108193] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.108198] dwc2 c90c0000.usb: set HCCHAR(12) to 00c89200
[  238.108201] dwc2 c90c0000.usb: dwc2_hc_init: Channel 12
[  238.108205] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.108208] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.108212] dwc2 c90c0000.usb: 	 Is In: 1
[  238.108215] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.108218] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.108222] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.108226] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.108229] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.108233] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.108237] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.108240] dwc2 c90c0000.usb: no split
[  238.108245] dwc2 c90c0000.usb: Wrote 00802000 to HCTSIZ(12)
[  238.108249] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 12
[  238.108252] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.108256] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.108259] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.108263] dwc2 c90c0000.usb: Wrote 1fd52000 to HCDMA(12)
[  238.108267] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.108271] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(12)
[  238.108276] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.108280] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.108569] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.108573] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.108577] dwc2 c90c0000.usb: HAINT=00001000
[  238.108581] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 12
[  238.108586] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.108590] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Channel Halted--
[  238.108594] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: DMA Channel Halted--
[  238.108598] dwc2 c90c0000.usb: --Host Channel 12 Interrupt: Transfer Complete--
[  238.108601] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.108606] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.108610] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 12
[  238.108613] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.108617] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.108626] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.108629] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.108633] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.108640] dwc2 c90c0000.usb: dwc2_host_complete: urb cd91f79f device 3 ep 2-IN status 0 actual 8192
[  238.108645] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.108648] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.108651] dwc2 c90c0000.usb: DMA enabled
[  238.108656] dwc2 c90c0000.usb:   dwc2_release_channel: channel 12, halt_status 2
[  238.108661] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.108664] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.108668] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.108671] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.108676] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.108680] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.108683] dwc2 c90c0000.usb: DMA enabled
[  238.108686] dwc2 c90c0000.usb: desc DMA disabled
[  238.108690] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.108694] dwc2 c90c0000.usb: set HAINTMSK to 00002000
[  238.108698] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.108702] dwc2 c90c0000.usb: set HCCHAR(13) to 00c89200
[  238.108706] dwc2 c90c0000.usb: dwc2_hc_init: Channel 13
[  238.108709] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.108713] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.108716] dwc2 c90c0000.usb: 	 Is In: 1
[  238.108720] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.108723] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.108726] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.108731] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.108734] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.108738] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.108742] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.108745] dwc2 c90c0000.usb: no split
[  238.108750] dwc2 c90c0000.usb: Wrote 00802000 to HCTSIZ(13)
[  238.108753] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 13
[  238.108757] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.108761] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.108764] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.108768] dwc2 c90c0000.usb: Wrote 1fe20000 to HCDMA(13)
[  238.108772] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.108776] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(13)
[  238.108780] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.108784] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.109059] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.109063] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.109066] dwc2 c90c0000.usb: HAINT=00002000
[  238.109071] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 13
[  238.109075] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.109079] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Channel Halted--
[  238.109083] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: DMA Channel Halted--
[  238.109087] dwc2 c90c0000.usb: --Host Channel 13 Interrupt: Transfer Complete--
[  238.109091] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.109095] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.109100] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 13
[  238.109103] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.109107] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.109110] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.109114] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.109118] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.109124] dwc2 c90c0000.usb: dwc2_host_complete: urb 67466227 device 3 ep 2-IN status 0 actual 8192
[  238.109129] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.109132] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.109136] dwc2 c90c0000.usb: DMA enabled
[  238.109140] dwc2 c90c0000.usb:   dwc2_release_channel: channel 13, halt_status 2
[  238.109145] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.109149] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.109152] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.109155] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.109160] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.109164] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.109168] dwc2 c90c0000.usb: DMA enabled
[  238.109171] dwc2 c90c0000.usb: desc DMA disabled
[  238.109175] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.109178] dwc2 c90c0000.usb: set HAINTMSK to 00004000
[  238.109182] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.109186] dwc2 c90c0000.usb: set HCCHAR(14) to 00c89200
[  238.109190] dwc2 c90c0000.usb: dwc2_hc_init: Channel 14
[  238.109194] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.109197] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.109200] dwc2 c90c0000.usb: 	 Is In: 1
[  238.109204] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.109207] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.109211] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.109215] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.109218] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.109222] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.109226] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.109229] dwc2 c90c0000.usb: no split
[  238.109234] dwc2 c90c0000.usb: Wrote 00802000 to HCTSIZ(14)
[  238.109237] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 14
[  238.109241] dwc2 c90c0000.usb: 	 Xfer Size: 8192
[  238.109244] dwc2 c90c0000.usb: 	 Num Pkts: 16
[  238.109248] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.109252] dwc2 c90c0000.usb: Wrote 1fc72000 to HCDMA(14)
[  238.109256] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.109260] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(14)
[  238.109264] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.109269] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000009 gintmsk=0xf300000e
[  238.109559] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.109564] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.109568] dwc2 c90c0000.usb: HAINT=00004000
[  238.109572] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 14
[  238.109576] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.109581] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Channel Halted--
[  238.109584] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: DMA Channel Halted--
[  238.109589] dwc2 c90c0000.usb: --Host Channel 14 Interrupt: Transfer Complete--
[  238.109593] dwc2 c90c0000.usb:   Bulk transfer complete
[  238.109597] dwc2 c90c0000.usb: urb->actual_length=0 xfer_length=8192
[  238.109601] dwc2 c90c0000.usb: DWC_otg: dwc2_update_urb_state: IN, channel 14
[  238.109605] dwc2 c90c0000.usb:   chan->xfer_len 8192
[  238.109608] dwc2 c90c0000.usb:   hctsiz.xfersize 0
[  238.109612] dwc2 c90c0000.usb:   urb->transfer_buffer_length 8192
[  238.109616] dwc2 c90c0000.usb:   urb->actual_length 8192
[  238.109619] dwc2 c90c0000.usb:   short_read 0, xfer_done 1
[  238.109626] dwc2 c90c0000.usb: dwc2_host_complete: urb a7ce381f device 3 ep 2-IN status 0 actual 8192
[  238.109631] dwc2 c90c0000.usb: dwc2_complete_non_periodic_xfer()
[  238.109635] dwc2 c90c0000.usb: dwc2_halt_channel()
[  238.109638] dwc2 c90c0000.usb: DMA enabled
[  238.109643] dwc2 c90c0000.usb:   dwc2_release_channel: channel 14, halt_status 2
[  238.109648] dwc2 c90c0000.usb:   dwc2_deactivate_qh(6099f2ba,7964d656,1)
[  238.109651] dwc2 c90c0000.usb: dwc2_hcd_qh_deactivate()
[  238.109655] dwc2 c90c0000.usb: dwc2_hcd_qh_unlink()
[  238.109659] dwc2 c90c0000.usb: DWC OTG HCD Finished Servicing Interrupts
[  238.109663] dwc2 c90c0000.usb: DWC OTG HCD gintsts=0x04000021 gintmsk=0xf300000e
[  238.109703] dwc2 c90c0000.usb: DWC OTG HCD URB Enqueue
[  238.109710] dwc2 c90c0000.usb: urb_enqueue, urb 45b274b6
[  238.109713] dwc2 c90c0000.usb:   Device address: 3
[  238.109717] dwc2 c90c0000.usb:   Endpoint: 2, IN
[  238.109721] dwc2 c90c0000.usb:   Endpoint type: BULK IN (IN)
[  238.109725] dwc2 c90c0000.usb:   Speed: HIGH
[  238.109729] dwc2 c90c0000.usb:   Max packet size: 512
[  238.109732] dwc2 c90c0000.usb:   Data buffer length: 13
[  238.109737] dwc2 c90c0000.usb:   Transfer buffer: 6257ab51, Transfer DMA: 3c041000
[  238.109741] dwc2 c90c0000.usb:   Setup buffer: b0cc1169, Setup DMA: 1fc9aa80
[  238.109745] dwc2 c90c0000.usb:   Interval: 0
[  238.109751] dwc2 c90c0000.usb: addr=3, ep_num=2, ep_dir=80, ep_type=2, mps=512
[  238.109756] dwc2 c90c0000.usb: dwc2_hcd_qh_add()
[  238.109799] dwc2 c90c0000.usb: dwc2_assign_and_init_hc(6099f2ba,7964d656)
[  238.109803] dwc2 c90c0000.usb: dwc2_hc_init()
[  238.109807] dwc2 c90c0000.usb: DMA enabled
[  238.109810] dwc2 c90c0000.usb: desc DMA disabled
[  238.109814] dwc2 c90c0000.usb: set HCINTMSK to 00000006
[  238.109818] dwc2 c90c0000.usb: set HAINTMSK to 00000001
[  238.109821] dwc2 c90c0000.usb: set GINTMSK to f300000e
[  238.109826] dwc2 c90c0000.usb: set HCCHAR(0) to 00c89200
[  238.109829] dwc2 c90c0000.usb: dwc2_hc_init: Channel 0
[  238.109833] dwc2 c90c0000.usb: 	 Dev Addr: 3
[  238.109836] dwc2 c90c0000.usb: 	 Ep Num: 2
[  238.109840] dwc2 c90c0000.usb: 	 Is In: 1
[  238.109843] dwc2 c90c0000.usb: 	 Is Low Speed: 0
[  238.109847] dwc2 c90c0000.usb: 	 Ep Type: 2
[  238.109850] dwc2 c90c0000.usb: 	 Max Pkt: 512
[  238.109854] dwc2 c90c0000.usb: Queue non-periodic transactions
[  238.109858] dwc2 c90c0000.usb:   NP Tx Req Queue Space Avail (before queue): 8
[  238.109861] dwc2 c90c0000.usb:   NP Tx FIFO Space Avail (before queue): 500
[  238.109865] dwc2 c90c0000.usb: dwc2_hc_start_transfer()
[  238.109869] dwc2 c90c0000.usb: no split
[  238.109873] dwc2 c90c0000.usb: Wrote 00080200 to HCTSIZ(0)
[  238.109877] dwc2 c90c0000.usb: dwc2_hc_start_transfer: Channel 0
[  238.109880] dwc2 c90c0000.usb: 	 Xfer Size: 512
[  238.109884] dwc2 c90c0000.usb: 	 Num Pkts: 1
[  238.109887] dwc2 c90c0000.usb: 	 Start PID: 0
[  238.109891] dwc2 c90c0000.usb: Wrote 3c041000 to HCDMA(0)
[  238.109895] dwc2 c90c0000.usb: 	 Multi Cnt: 1
[  238.109899] dwc2 c90c0000.usb: Wrote 80d89200 to HCCHAR(0)
[  238.109910] dwc2 c90c0000.usb: DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x02000000
[  238.109914] dwc2 c90c0000.usb: dwc2_hc_intr()
[  238.109917] dwc2 c90c0000.usb: HAINT=00000001
[  238.109921] dwc2 c90c0000.usb: --Host Channel Interrupt--, Channel 0
[  238.109926] dwc2 c90c0000.usb:   hcint 0x00000023, hcintmsk 0x00000006, hcint&hcintmsk 0x00000002
[  238.1099