[RFT net-next v4 3/5] net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration
Martin Blumenstingl
martin.blumenstingl at googlemail.com
Sun Jan 14 13:48:56 PST 2018
Tests (using an oscilloscope and an Odroid-C1 board with a RTL8211F
RGMII PHY) have shown that the PRG_ETH0 register behaves as follows:
- bit 4 is a mux to choose between two parent clocks. according to the
public S805 datasheet the only supported parent clock is MPLL2 (this
was not verified using the oscilloscope).
The public S805/S905 datasheet claims that this bit is reserved.
- bits 9:7 control a one-based divider (register value 1 means "divide
by 1", etc.) for the input clock. we call this clock the "m250_div"
clock because it's value is always supposed to be (close to) 250MHz
(see below for an explanation).
The description in the public S805/S905 datasheet is a bit cryptic,
but it comes down to "input clock = 250MHz * value" (which could also
be expressed as "250MHz = input clock / value")
- there seems to be an internal fixed divide-by-2 clock which takes the
output from the m250_div and divides it by 2. This is not unusual on
Amlogic SoCs, since the SDIO (MMC) driver also uses an internal fixed
divide-by-2 clock.
This is not documented in the public S805/S905 datasheet
- bit 10 controls a gate clock which enables or disables the RGMII TX
clock (which is an output on the MAC/SoC and an input in the PHY). we
call this the "rgmii_tx_en" clock. if this bit is set to "0" the RGMII
TX clock output is close to 0
The description for this bit in the public S805/S905 datasheet is
"Generate 25MHz clock for PHY". Based on these tests it's believed
that this is wrong, and should probably read "Generate the 125MHz
RGMII TX clock for the PHY"
- the RGMII TX clock has to be set to 125MHz - the IP block adjusts the
output (automatically) depending on the line speed (RGMII specifies
that Gbit connections use a 125MHz clock, 100Mbit/s connections use a
25MHz clock and 10Mbit/s connections use a 2.5MHz clock. only Gbit and
100Mbit/s were tested with an oscilloscope). Due to the requirement
that this clock always has to be set to 125MHz and due to the fixed
divide-by-2 parent clock this means that m250_div will always end up
with a rate of (close to) 250MHz.
- bits 6:5 are the TX delay, which is also named "clock phase" in some
of Amlogic's older GPL kernel sources.
The PHY also has an XTAL_IN pin where a 25MHz clock has to be provided.
Tests with the oscilloscope have shown that this is routed to a crystal
right next to the RTL8211F PHY. The same seems to be true on the Khadas
VIM2 (which uses a GXM SoC) board - however the 25MHz crystal is on the
other side of the PCB there.
This updates the clocks in the dwmac-meson8b driver by replacing the
"m25_div" with the "rgmii_tx_en" clock and additionally introducing a
fixed divide-by-2 clock between "m250_div" and "rgmii_tx_en".
Now we also need to set a frequency of 125MHz on the RGMII clock
(opposed to the 25MHz we set before, with that non-existing
divide-by-5-or-10 divider).
Special thanks go to Linus Lüssing for testing the various bits and
checking the results with an oscilloscope on his Odroid-C1!
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: Emiliano Ingrassia <ingrassia at epigenesys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
---
.../net/ethernet/stmicro/stmmac/dwmac-meson8b.c | 79 +++++++++++++---------
1 file changed, 47 insertions(+), 32 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
index 670f344f7168..e9fec9e0425c 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
@@ -40,9 +40,7 @@
#define PRG_ETH0_CLK_M250_DIV_SHIFT 7
#define PRG_ETH0_CLK_M250_DIV_WIDTH 3
-/* divides the result of m25_sel by either 5 (bit unset) or 10 (bit set) */
-#define PRG_ETH0_CLK_M25_DIV_SHIFT 10
-#define PRG_ETH0_CLK_M25_DIV_WIDTH 1
+#define PRG_ETH0_RGMII_TX_CLK_EN 10
#define PRG_ETH0_INVERTED_RMII_CLK BIT(11)
#define PRG_ETH0_TX_AND_PHY_REF_CLK BIT(12)
@@ -63,8 +61,11 @@ struct meson8b_dwmac {
struct clk_divider m250_div;
struct clk *m250_div_clk;
- struct clk_divider m25_div;
- struct clk *m25_div_clk;
+ struct clk_fixed_factor fixed_div2;
+ struct clk *fixed_div2_clk;
+
+ struct clk_gate rgmii_tx_en;
+ struct clk *rgmii_tx_en_clk;
u32 tx_delay_ns;
};
@@ -88,11 +89,6 @@ static int meson8b_init_rgmii_tx_clk(struct meson8b_dwmac *dwmac)
struct device *dev = &dwmac->pdev->dev;
const char *clk_div_parents[1];
const char *mux_parent_names[MUX_CLK_NUM_PARENTS];
- static const struct clk_div_table clk_25m_div_table[] = {
- { .val = 0, .div = 5 },
- { .val = 1, .div = 10 },
- { /* sentinel */ },
- };
/* get the mux parents from DT */
for (i = 0; i < MUX_CLK_NUM_PARENTS; i++) {
@@ -149,25 +145,40 @@ static int meson8b_init_rgmii_tx_clk(struct meson8b_dwmac *dwmac)
if (WARN_ON(IS_ERR(dwmac->m250_div_clk)))
return PTR_ERR(dwmac->m250_div_clk);
- /* create the m25_div */
- init.name = devm_kasprintf(dev, GFP_KERNEL, "%s#m25_div",
+ /* create the fixed_div2 */
+ init.name = devm_kasprintf(dev, GFP_KERNEL, "%s#fixed_div2",
dev_name(dev));
- init.ops = &clk_divider_ops;
- init.flags = CLK_IS_BASIC | CLK_SET_RATE_PARENT;
+ init.ops = &clk_fixed_factor_ops;
+ init.flags = CLK_SET_RATE_PARENT;
clk_div_parents[0] = __clk_get_name(dwmac->m250_div_clk);
init.parent_names = clk_div_parents;
init.num_parents = ARRAY_SIZE(clk_div_parents);
- dwmac->m25_div.reg = dwmac->regs + PRG_ETH0;
- dwmac->m25_div.shift = PRG_ETH0_CLK_M25_DIV_SHIFT;
- dwmac->m25_div.width = PRG_ETH0_CLK_M25_DIV_WIDTH;
- dwmac->m25_div.table = clk_25m_div_table;
- dwmac->m25_div.hw.init = &init;
- dwmac->m25_div.flags = CLK_DIVIDER_ALLOW_ZERO;
+ dwmac->fixed_div2.mult = 1;
+ dwmac->fixed_div2.div = 2;
+ dwmac->fixed_div2.hw.init = &init;
+
+ dwmac->fixed_div2_clk = devm_clk_register(dev, &dwmac->fixed_div2.hw);
+ if (WARN_ON(IS_ERR(dwmac->fixed_div2_clk)))
+ return PTR_ERR(dwmac->fixed_div2_clk);
+
+ /* create the rgmii_tx_en */
+ init.name = devm_kasprintf(dev, GFP_KERNEL, "%s#rgmii_tx_en",
+ dev_name(dev));
+ init.ops = &clk_gate_ops;
+ init.flags = CLK_SET_RATE_PARENT;
+ clk_div_parents[0] = __clk_get_name(dwmac->fixed_div2_clk);
+ init.parent_names = clk_div_parents;
+ init.num_parents = ARRAY_SIZE(clk_div_parents);
+
+ dwmac->rgmii_tx_en.reg = dwmac->regs + PRG_ETH0;
+ dwmac->rgmii_tx_en.bit_idx = PRG_ETH0_RGMII_TX_CLK_EN;
+ dwmac->rgmii_tx_en.hw.init = &init;
- dwmac->m25_div_clk = devm_clk_register(dev, &dwmac->m25_div.hw);
- if (WARN_ON(IS_ERR(dwmac->m25_div_clk)))
- return PTR_ERR(dwmac->m25_div_clk);
+ dwmac->rgmii_tx_en_clk = devm_clk_register(dev,
+ &dwmac->rgmii_tx_en.hw);
+ if (WARN_ON(IS_ERR(dwmac->rgmii_tx_en_clk)))
+ return PTR_ERR(dwmac->rgmii_tx_en_clk);
return 0;
}
@@ -200,18 +211,22 @@ static int meson8b_init_prg_eth(struct meson8b_dwmac *dwmac)
meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TXDLY_MASK,
tx_dly_val << PRG_ETH0_TXDLY_SHIFT);
- ret = clk_prepare_enable(dwmac->m25_div_clk);
+ /* Configure the 125MHz RGMII TX clock, the IP block changes
+ * the output automatically (= without us having to configure
+ * a register) based on the line-speed (125MHz for Gbit speeds,
+ * 25MHz for 100Mbit/s and 2.5MHz for 10Mbit/s).
+ */
+ ret = clk_set_rate(dwmac->rgmii_tx_en_clk, 125 * 1000 * 1000);
if (ret) {
- dev_err(&dwmac->pdev->dev, "failed to enable the PHY clock\n");
+ dev_err(&dwmac->pdev->dev,
+ "failed to set RGMII TX clock\n");
return ret;
}
- /* Generate the 25MHz RGMII clock for the PHY */
- ret = clk_set_rate(dwmac->m25_div_clk, 25 * 1000 * 1000);
+ ret = clk_prepare_enable(dwmac->rgmii_tx_en_clk);
if (ret) {
- clk_disable_unprepare(dwmac->m25_div_clk);
-
- dev_err(&dwmac->pdev->dev, "failed to set PHY clock\n");
+ dev_err(&dwmac->pdev->dev,
+ "failed to enable the RGMII TX clock\n");
return ret;
}
break;
@@ -305,7 +320,7 @@ static int meson8b_dwmac_probe(struct platform_device *pdev)
err_clk_disable:
if (phy_interface_mode_is_rgmii(dwmac->phy_mode))
- clk_disable_unprepare(dwmac->m25_div_clk);
+ clk_disable_unprepare(dwmac->rgmii_tx_en_clk);
err_remove_config_dt:
stmmac_remove_config_dt(pdev, plat_dat);
@@ -317,7 +332,7 @@ static int meson8b_dwmac_remove(struct platform_device *pdev)
struct meson8b_dwmac *dwmac = get_stmmac_bsp_priv(&pdev->dev);
if (phy_interface_mode_is_rgmii(dwmac->phy_mode))
- clk_disable_unprepare(dwmac->m25_div_clk);
+ clk_disable_unprepare(dwmac->rgmii_tx_en_clk);
return stmmac_pltfr_remove(pdev);
}
--
2.15.1
More information about the linux-amlogic
mailing list