[RFC PATCH v1] pinctrl: meson: meson8b: fix requesting GPIOs greater than GPIOZ_3
Martin Blumenstingl
martin.blumenstingl at googlemail.com
Mon Feb 19 13:19:46 PST 2018
Hi Jerome,
On Mon, Feb 19, 2018 at 9:07 AM, Jerome Brunet <jbrunet at baylibre.com> wrote:
> On Sat, 2018-02-17 at 20:44 +0100, Martin Blumenstingl wrote:
>> Hi Jerome,
>>
>> On Wed, Jan 24, 2018 at 6:54 PM, Martin Blumenstingl
>> <martin.blumenstingl at googlemail.com> wrote:
>> > Hi Jerome,
>> >
>> > On Wed, Jan 24, 2018 at 3:52 PM, Jerome Brunet <jbrunet at baylibre.com> wrote:
>> > > On Wed, 2018-01-24 at 11:10 +0100, Martin Blumenstingl wrote:
>> > > > Hi Jerome,
>> > > >
>> > > > On Wed, Jan 24, 2018 at 9:28 AM, Jerome Brunet <jbrunet at baylibre.com> wrote:
>> > > > > On Wed, 2018-01-24 at 01:27 +0100, Martin Blumenstingl wrote:
>> > > > > > Meson8b is a cost reduced variant of the Meson8 SoC. It's package size
>> > > > > > is smaller than Meson8.
>> > > > > > Unfortunately there are a few key differences which cannot be seen
>> > > > > > without close inspection of the code and the public S805 data-sheet:
>> > > > > > - the GPIOX bank is missing the GPIOX_12, GPIOX_13, GPIOX_14 and
>> > > > > > GPIOX_15 GPIOs
>> > > > > > - the GPIOY bank is missing the GPIOY_2, GPIOY_4, GPIOY_5, GPIOY_15 and
>> > > > > > GPIOY_16 GPIOs
>> > > > > > - the GPIODV bank is missing all GPIOs except GPIODV_9, GPIODV_24,
>> > > > > > GPIODV_25, GPIODV_26, GPIODV_27, GPIODV_28 and GPIODV_29
>> > > > > > - the GPIOZ bank is missing completely
>> > > > > > - there is a new GPIO bank called "DIF"
>> > > > > > - (all other pads exist on both, Meson8 and Meson8b)
>> > > > > >
>> > > > > > The pinctrl-meson driver internally uses struct meson_bank, which
>> > > > > > assumes that the GPIOs are continuous, without any holes in between.
>> > > > > > This also matches with how the registers work:
>> > > > > > - GPIOX_0 for example uses bit 0 for switching this pad between
>> > > > > > input/output, configuring pull-up/down, etc.
>> > > > > > - GPIOX_16 uses bit 16 for switching this pad between input/output,
>> > > > > > configuring pull-up/down/, etc
>> > > > > > GPIOX_16 uses bit 16 even though GPIOX12..15 don't exist. (This is
>> > > > > > probably the reason why Meson8b inherits the dt-bindings - with all GPIO
>> > > > > > IDs - from Meson8)
>> > > > > > This means that Meson8b only has 83 actual GPIO lines. Without any holes
>> > > > > > there would be 130 GPIO lines in total (120 are inherited from Meson8
>> > > > > > plus 10 new from the DIF bank).
>> > > > > >
>> > > > > > The pinctrl framework handles holes in the pin list fine, which can be
>> > > > > > seen in debugfs:
>> > > > > > $ cat /sys/kernel/debug/pinctrl/c1109880.pinctrl/pins
>> > > > > > pin 9 (GPIOX_9) c1109880.pinctrl
>> > > > > > pin 10 (GPIOX_10) c1109880.pinctrl
>> > > > > > pin 11 (GPIOX_11) c1109880.pinctrl
>> > > > > > pin 16 (GPIOX_16) c1109880.pinctrl
>> > > > > > pin 17 (GPIOX_17) c1109880.pinctrl
>> > > > >
>> > > > > Hi Martin,
>> > > > >
>> > > > > While working on this controller a few weeks ago, I have seen that our current
>> > > > > design does not tolerate having holes in the declared PINS. This is something
>> > > > > that predate the changes mentioned here.
>> > > > >
>> > > > > I'm not a big fan of the this overrides_ngpio here, I'm sure it fixes your
>> > > > > problem but it seems a bit hacky, don't you think ?
>> > > >
>> > > > this is the reason why I sent it as RFC - I'm open to better solutions!
>> > > >
>> > > > > I would prefer either of these 2 approach:
>> > > > >
>> > > > > * Update the binding and kill the necessary pins. We are still figuring out
>> > > > > those chips, which is why the bindings are marked as un-stable. If sharing the
>> > > > > binding with meson8 was a mistake, now is the time to fix it.
>> > > >
>> > > > let's say we produce a header file which does not contain GPIOX_12:
>> > > > this would be nice since it gives compile errors if non-existent GPIOs
>> > > > are used (instead of failing only at run-time)
>> > > >
>> > > > however, the problem is meson8b_cbus_banks (annotated here to make it
>> > > > easier to read):
>> > > > BANK("X", /* name */
>> > > > GPIOX_0, GPIOX_21, /* first and last GPIO */
>> > > > 97, 118, /* first and last IRQ */
>> > > > 4, 0, /* pull-up/down enable register and bit offset */
>> > > > 4, 0, /* pull-up/down configuration register and bit offset */
>> > > > 0, 0, /* input/output direction register and bit offset */
>> > > > 1, 0, /* output value register and bit offset */
>> > > > 2, 0), /* input value register and bit offset */
>> > > >
>> > > > let's say we want to configure GPIOX_0 as an input:
>> > > > - we need to find the "offset" of this pad within the bank -> 0
>> > > > - find the input/output direction register -> 0
>> > > > - find the bit in that register: bit 0 + pad offset 0 = 0
>> > > > - we clear bit 0 in register 0
>> > > >
>> > > > with the current code configuring GPIOX_16 as input works like this:
>> > > > - we need to find the "offset" of this pad within the bank -> 16
>> > > > - find the input/output direction register -> 0
>> > > > - find the bit in that register: bit 0 + pad offset 16 = 16
>> > > > - we clear bit 16 in register 0
>> > >
>> > > If offset calculation is really the problem, nothing is stopping you from the
>> > > splitting BANK in two. With your example of GPIOX_12...15 missing:
>> > >
>> > > BANK("X1", /* name */
>> > > GPIOX_0, GPIOX_11, /* first and last GPIO */
>> > > 97, 108, /* first and last IRQ */
>> > > 4, 0, /* pull-up/down enable register and bit offset */
>> > > 4, 0, /* pull-up/down configuration register and bit offset */
>> > > 0, 0, /* input/output direction register and bit offset */
>> > > 1, 0, /* output value register and bit offset */
>> > > 2, 0), /* input value register and bit offset */
>> > >
>> > > BANK("X2", /* name */
>> > > GPIOX_16, GPIOX_21, /* first and last GPIO */
>> > > 113, 118, /* first and last IRQ */
>> > > X, Y, /* pull-up/down enable register and bit offset */
>> > > X, Y, /* pull-up/down configuration register and bit offset */
>> > > Z, XX, /* input/output direction register and bit offset */
>> > > FOO, 0, /* output value register and bit offset */
>> > > BAR, 0), /* input value register and bit offset */
>> >
>> > nice thinking :)
>> > the only solution I could come up with was to change the MESON_PIN
>> > definition to something like:
>> > #define MESON_PIN(pad, pullen_bit, pull_bit, direction_bit,
>> > output_bit, input_bit, irq_num)
>> >
>> > that however means that we would have to change a lot of code in all
>> > pinctrl drivers
>> >
>> > > >
>> > > > let's assume that we removed GPIOX_12...15 from Meson8b
>> > > > GPIOX_16 could now have the same value that was assigned to GPIOX_12
>> > > > before (= 12)
>> > > > but how do we now know the offset of GPIOX_16?
>> > > > if we don't consider it in the calculation above we would end up
>> > > > writing to bit 12 (instead of bit 16).
>> > > >
>> > > > we could still cleanup the header file but leave the IDs of the
>> > > > existing GPIOs untouched (so GPIOX_16 would still be 16).
>> > >
>> > > I don't really get the point of doing so, especially is this patch is still
>> > > needed in the end.
>> > >
>> > > > however, that means that this patch is still needed because our last
>> > > > ID would be DIF_4_N (= value 129) again (so with holes our total count
>> > > > is still 130).
>> > > > with that we wouldn't even break the DT ABI
>> > >
>> > > While I prefer changing the bindings over the 'over_ngpio' tweak, it is not my
>> > > favorite solution.
>> > >
>> > > >
>> > > > > * If meson8b is indeed a cost reduction, it is likely to be same the approach as
>> > > > > s905x vs s905d: The D version is the same SoC with less ball pad but, as far as
>> > > > > we know, the logic is still there on the silicium (same die), it is just not
>> > > > > routed to the outside world. Both version share the same pinctrl driver (gxl).
>> > > > > The pad not routed to the outside world can just be considered "internal pads"
>> > > >
>> > > > there are a few differences between Meson8 and Meson8b, see also [0]:
>> > > > - Meson8 (and Meson8m2) CPU cores: 4x Cortex-A9
>> > > > - Meson8b CPU cores: 4x Cortex-A5
>> > > > - Meson8 (and Meson8m2) GPU: Mali-450MP8
>> > > > - Meson8b GPU: Mali-450MP4
>> > > > - Meson8 (and Meson8m2) package size: 19mm x 19 mm, LFBGA
>> > > > - Meson8b package size: 12mm x 12 mm, LFBGA
>> > > >
>> > > > the pinctrl register layout seems to be *mostly* compatible between
>> > > > Meson8 and Meson8b.
>> > > > unfortunately it's not entirely compatible, here is one example:
>> > > > - Meson8: GROUP(uart_tx_b1, 6, 23),
>> > > > - Meson8b: GROUP(uart_tx_b1, 6, 19),
>> > > > - Meson8: GROUP(eth_mdc, 6, 5),
>> > > > - Meson8b: GROUP(eth_mdc, 6, 9),
>> > > >
>> > > > > Long story short, if meson8 and meson8b share the same bindings, maybe they
>> > > > > should also share the driver. If they can't share the driver because they are
>> > > > > definitely incompatible, maybe they should not share the same bindings
>> > > >
>> > > > based on what I have seen so far I believe that they should not share
>> > > > the same bindings
>> > >
>> > > It looks to me to be same gpio/pinconf IP with a few pads not exposed to the
>> > > outside world, so I think they could share the bindings, and apparently fair
>> > > part of the driver data.
>> > >
>> > > Apparently amlogic tweaked a bit the pinmux. With the current architecture of
>> > > our pinctrl driver, it should be fairly easy to register 2 drivers sharing
>> > > everything but the GROUP table (and maybe the FUNCS if necessary)
>> > >
>> > > If possible, I would be more in favor of this last solution, as we could kill
>> > > one the pinctrl-meson8.c file, which are mostly a copy/paste of one another.
>> > > While fixing you issue, we would end up with less code to maintain and save a
>> > > bit of memory.
>> > >
>> > > Do you see any other big issue with this approach ?
>> >
>> > I would have to go through the whole list of pads to see what the
>> > actual differences are
>>
>> I tried to automate this as far as possible with the attached script
>> you can use it like this:
>> - first get the gpio.c files from the Amlogic 3.10 kernel for Meson8
>> and Meson8b: [0] and [1]
>> - ./list-meson8-pinmux-reg-bits.sh path/to/meson8/gpio.c | sort -u > meson8.txt
>> - ./list-meson8-pinmux-reg-bits.sh path/to/meson8b/gpio.c | sort -u >
>> meson8b.txt
>> - diff -Naur meson8.txt meson8b.txt > diff.patch
>> - (the resulting diff is attached)
>> - compare the Meson8 documentation (found in a .csv file, see [2])
>> with the public Meson8b datasheet (see [3])
>>
>> the major differences are:
>> - DIF_TTL bank only exists on Meson8b
>> - GPIOZ bank only exists on Meson8
>> - HDMI_TTL bank only exists on Meson8b (not supported by our mainline driver)
>> - some of the Ethernet pins are using the GPIOH bank on Meson8b while
>> Meson8 has these in the GPIOZ bank
>> - Meson8b has various SPI pins in the GPIOH bank while Meson8 has them
>> in the GPIOZ bank
>> - Meson8 only has pins for one TSin interface, Meson8b seems to
>> support two TSin interfaces
>>
>> smaller differences are:
>> - the LCD_* pins (maybe even all of the LCD support) in GPIODV only
>> exists on Meson8
>> - Meson8b has the I2C_A pins on GPIODV_24 and GPIODV_25 (Meson8 has
>> multiple pins for this in the GPIOZ bank)
>> - Meson8b has the I2C_B pins on GPIODV_26 and GPIODV_27 (Meson8 has
>> these on GPIOZ_2 and GPIOZ_3)
>> - Meson8b has the I2C_C pins on GPIODV_28 and GPIODV_29 (Meson8 two
>> chices: either GPIOY_0 and GPIOY_1 or GPIOZ_4 and GPIOZ_5)
>> - the XTAL_24M_OUT signal uses GPIODV_29 on Meson8b but GPIOX_11 on Meson8
>> - Meson8b can output UART_CTS_B on GPIOX_10 - Meson8 supports GPIODV_26 instead
>> - Meson8b can output UART_RTS_B on GPIOX_20 - Meson8 supports GPIODV_27 instead
>> - Meson8b can output SPI_SS0 on GPIOX_20 - Meson8 supports GPIOZ_9 instead
>>
>> not checked yet:
>> - Meson8b seems to have a few more bits in BOOT_8 BOOT_10 and BOOT_18
>> - Meson8b seems to have a few more bits in GPIOAO_2, GPIOAO_3,
>> GPIOAO_6, GPIOAO_7, GPIOAO_9, GPIOAO_10 and GPIOAO_13
>> - GPIOY_0, GPIOX_4, GPIOX_5, GPIOX_6, GPIOX_7, GPIOX_8, GPIOX_9
>> - the changes (there are quite a few) in the GPIOY bank
>>
>> notes for other pins I have randomly checked:
>> - Meson8b's gpio.c has a function for GPIOX_0 at reg9[24] - this seems
>> undocumented
>> - Meson8b's gpio.c has a function for GPIOX_1 at reg9[23] - this seems
>> undocumented
>> - Meson8b's gpio.c has a function for GPIOX_2 at reg9[22] - this seems
>> undocumented
>> - Meson8b's gpio.c has a function for GPIOX_3 at reg9[21] - this seems
>> undocumented
>>
>> I'm not sure if we should try to create a unified pinctrl driver for
>> Meson8 and Meson8b
>
> Thanks the detailed summary Martin ! I agree with you. meson8b obviously derives
> from meson8 but there is to many subtle differences to create unified driver ...
> w/o adding spaghetti code around
yes, I think in this case some code-duplication is better than making
the code harder to read by introducing quite a few "use this register
bit or pad on Meson8, but another on Meson8b"
> Is the "2 banks" solution enough to solve the problem cleanly ?
I haven't tested it yet - I'll report back once I did
but based on your previous suggestion it should work
> If not and it still leaves problems to be solved in the future, maybe we would
> be better off with different bindings for meson8 and meson8b ? and be done with
> it ...
I'll test your split bank solution first, then we can discuss the next steps
>
>> so far we have:
>> - meson_pmx_group are roughly 67% identical (meson_pmx_func depend on
>> meson_pmx_group)
>> - different pinctrl_pin_desc (due to different GPIO banks)
>> - different IRQ numbering
>>
>> so I wonder how much we would actually save by creating a unified
>> Meson8/Meson8b pinctrl driver.
>>
>> as a side-note: I found out that Meson8m2 has 10 pins which each add
>> one function compared to Meson8, see: [4]
>> I would integrate these into the Meson8 driver (if we keep separate
>> drivers for Meson8 and Meson8b) when needed, because these definitely
>> don't justify adding a new pinctrl driver
>>
>>
>> Regards
>> Martin
>>
>>
>> [0] https://github.com/endlessm/linux-meson/blob/5cb4882cdda584878a29132aeb9a90497a121df9/arch/arm/mach-meson8/gpio.c
>> [1] https://github.com/endlessm/linux-meson/blob/5cb4882cdda584878a29132aeb9a90497a121df9/arch/arm/mach-meson8b/gpio.c
>> [2] https://github.com/endlessm/linux-meson/blob/5cb4882cdda584878a29132aeb9a90497a121df9/arch/arm/mach-meson8/tool/m8_gpio.csv
>> [3] https://dn.odroid.com/S805/Datasheet/S805_Datasheet%20V0.8%2020150126.pdf
>> [4] https://github.com/endlessm/linux-meson/blob/5cb4882cdda584878a29132aeb9a90497a121df9/arch/arm/mach-meson8/gpio.c#L242
>
Regards
Martin
More information about the linux-amlogic
mailing list