[PATCH v7 usb-next 3/4] usb: core: hcd: integrate the PHY roothub wrapper

[Martin Blumenstingl]

Hi Manu,

thank you for reviewing this!

On Thu, Oct 26, 2017 at 7:42 AM, Manu Gautam <mgautam at codeaurora.org> wrote:
> Hi,
>
>
> On 10/24/2017 3:27 AM, Martin Blumenstingl wrote:
>> This integrates the PHY roothub wrapper into the core hcd
>> infrastructure. Multiple PHYs which are part of the roothub devicetree
>> node (which is a sub-node of the sysdev's node) are now managed
>> (= powered on/off when needed), by the new usb_phy_roothub code.
>>
>> One example where this is required is the Amlogic GXL and GXM SoCs:
>> They are using a dwc3 USB controller with up to three ports enabled on
>> the internal roothub. Using only the top-level "phy" properties does not
>> work here since one can only specify one "usb2-phy" and one "usb3-phy",
>> while actually at least two "usb2-phy" have to be specified.
>>
>> Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
>> Tested-by: Neil Armstrong <narmstrong at baylibre.com>
>> Acked-by: Alan Stern <stern at rowland.harvard.edu>
>> ---
>>  drivers/usb/core/hcd.c  | 26 ++++++++++++++++++++++++++
>>  include/linux/usb/hcd.h |  1 +
>>  2 files changed, 27 insertions(+)
>>
>> diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
>> index 67aa3d039b9b..6ee97222cdad 100644
>> --- a/drivers/usb/core/hcd.c
>> +++ b/drivers/usb/core/hcd.c
>> @@ -50,6 +50,7 @@
>>  #include <linux/usb/otg.h>
>>
>>  #include "usb.h"
>> +#include "phy.h"
>>
>>
>>  /*-------------------------------------------------------------------------*/
>> @@ -2271,6 +2272,8 @@ int hcd_bus_suspend(struct usb_device *rhdev, pm_message_t msg)
>>               usb_set_device_state(rhdev, USB_STATE_SUSPENDED);
>>               hcd->state = HC_STATE_SUSPENDED;
>>
>> +             usb_phy_roothub_power_off(hcd->phy_roothub);
>> +
>
> For system-suspend it should be ok.
> But, in case of runtime/auto suspend, I think PHYs shouldn't be powered off.
> Should we have check for that like-
>
> if (!PMSG_IS_AUTO(msg))
>     usb_phy_roothub_power_off()
>
> Similar check in hcd_bus_resume?
disclaimer: I must admit that I am not very familiar with the PM code
and even worse: the platform I'm developing with does not have suspend support

can I take your suggestion and include it in the next version of this
series or should we wait for feedback from another developer on this
topic?

>
>>               /* Did we race with a root-hub wakeup event? */
>>               if (rhdev->do_remote_wakeup) {
>>                       char    buffer[6];
>> @@ -2307,6 +2310,11 @@ int hcd_bus_resume(struct usb_device *rhdev, pm_message_t msg)
>>               dev_dbg(&rhdev->dev, "skipped %s of dead bus\n", "resume");
>>               return 0;
>>       }
>> +
>> +     status = usb_phy_roothub_power_on(hcd->phy_roothub);
>> +     if (status)
>> +             return status;
>> +
>
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>


Regards
Martin