[PATCH] pwm: meson: fix harware duty calculation

Yixun Lan yixun.lan at amlogic.com
Tue Nov 28 19:03:08 PST 2017


From: Jian Hu <jian.hu at amlogic.com>

The actual HIGH/LOW signal output from the PWM is equal to
the value programed to HW register plus one, this is designed by HW.

This fix should apply to all Meson SoC(include GX/GXL/GXBB, Meson6,8)

Fixes: 211ed630753d ("pwm: Add support for Meson PWM Controller")
Signed-off-by: Jian Hu <jian.hu at amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan at amlogic.com>
---
 drivers/pwm/pwm-meson.c | 19 ++++++++++++++-----
 1 file changed, 14 insertions(+), 5 deletions(-)

diff --git a/drivers/pwm/pwm-meson.c b/drivers/pwm/pwm-meson.c
index d589331d1884..78d9b8c1a4bc 100644
--- a/drivers/pwm/pwm-meson.c
+++ b/drivers/pwm/pwm-meson.c
@@ -193,6 +193,11 @@ static int meson_pwm_calc(struct meson_pwm *meson,
 			break;
 	}
 
+	if (cnt < 2) {
+		dev_err(meson->chip.dev, "invalid period\n");
+		return -EINVAL;
+	}
+
 	if (pre_div == MISC_CLK_DIV_MASK) {
 		dev_err(meson->chip.dev, "unable to get period pre_div\n");
 		return -EINVAL;
@@ -201,19 +206,23 @@ static int meson_pwm_calc(struct meson_pwm *meson,
 	dev_dbg(meson->chip.dev, "period=%u pre_div=%u cnt=%u\n", period,
 		pre_div, cnt);
 
+	/*
+	 * Due to the design of hardware, values of 'hi', 'lo' are 1 based
+	 * which mean the actual output from hardware is 'hi' + 1, 'lo' + 1
+	 */
 	if (duty == period) {
 		channel->pre_div = pre_div;
-		channel->hi = cnt;
+		channel->hi = cnt - 1;
 		channel->lo = 0;
 	} else if (duty == 0) {
 		channel->pre_div = pre_div;
 		channel->hi = 0;
-		channel->lo = cnt;
+		channel->lo = cnt - 1;
 	} else {
 		/* Then check is we can have the duty with the same pre_div */
 		duty_cnt = DIV_ROUND_CLOSEST_ULL((u64)duty * 1000,
 						 fin_ps * (pre_div + 1));
-		if (duty_cnt > 0xffff) {
+		if (duty_cnt > 0xffff || !duty_cnt) {
 			dev_err(meson->chip.dev, "unable to get duty cycle\n");
 			return -EINVAL;
 		}
@@ -222,8 +231,8 @@ static int meson_pwm_calc(struct meson_pwm *meson,
 			duty, pre_div, duty_cnt);
 
 		channel->pre_div = pre_div;
-		channel->hi = duty_cnt;
-		channel->lo = cnt - duty_cnt;
+		channel->hi = duty_cnt - 1;
+		channel->lo = cnt - duty_cnt - 1;
 	}
 
 	return 0;
-- 
2.15.0




More information about the linux-amlogic mailing list