[RFC PATCH u-boot v2] ARM: arch-meson: build memory banks using reported memory from registers

Neil Armstrong narmstrong at baylibre.com
Mon Nov 6 03:10:08 PST 2017


On 19/10/2017 20:38, Ben Dooks wrote:
> On 2017-10-19 14:22, Neil Armstrong wrote:
>> As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
>> and a secondary BL32 firmware.
>> Since mid-2017, the reserved memory address of the BL31 firmware was moved
>> and grown for security reasons.
>>
>> But mainline U-boot and Linux has the old address and size fixed.
>>
>> These SoCs have a register interface to get the two firmware reserved
>> memory start and sizes.
>>
>> This patch adds a dynamic reservation of the memory zones in the
>> device tree bootmem
>> reserved memory zone used by the kernel in early boot.
>> To be complete, the memory zones are also added to the EFI reserved zones.
>>
>> [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
>>
>> Changes since v1:
>> - switch to fdt rsv mem table and efi reserve memory
>> - replaced in_le32 by readl()
>>
>> Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
>> ---
>>  arch/arm/include/asm/arch-meson/gxbb.h |  17 +++++
>>  arch/arm/mach-meson/board.c            | 117 ++++++++++++++++++++++++++++++---
>>  board/amlogic/odroid-c2/odroid-c2.c    |   7 ++
>>  board/amlogic/p212/p212.c              |   7 ++
>>  configs/odroid-c2_defconfig            |   1 +
>>  configs/p212_defconfig                 |   1 +
>>  include/configs/meson-gxbb-common.h    |   2 +-
>>  7 files changed, 143 insertions(+), 9 deletions(-)
>>
>> diff --git a/arch/arm/include/asm/arch-meson/gxbb.h
>> b/arch/arm/include/asm/arch-meson/gxbb.h
>> index 74d5290..117f796 100644
>> --- a/arch/arm/include/asm/arch-meson/gxbb.h
>> +++ b/arch/arm/include/asm/arch-meson/gxbb.h
>> @@ -7,10 +7,27 @@
>>  #ifndef __GXBB_H__
>>  #define __GXBB_H__
>>
>> +#define GXBB_FIRMWARE_MEM_SIZE    0x1000000
>> +
>> +#define GXBB_AOBUS_BASE        0xc8100000
>>  #define GXBB_PERIPHS_BASE    0xc8834400
>>  #define GXBB_HIU_BASE        0xc883c000
>>  #define GXBB_ETH_BASE        0xc9410000
>>
>> +/* Always-On Peripherals registers */
>> +#define GXBB_AO_ADDR(off)    (GXBB_AOBUS_BASE + ((off) << 2))
>> +
>> +#define GXBB_AO_SEC_GP_CFG0    GXBB_AO_ADDR(0x90)
>> +#define GXBB_AO_SEC_GP_CFG3    GXBB_AO_ADDR(0x93)
>> +#define GXBB_AO_SEC_GP_CFG4    GXBB_AO_ADDR(0x94)
>> +#define GXBB_AO_SEC_GP_CFG5    GXBB_AO_ADDR(0x95)
>> +
>> +#define GXBB_AO_MEM_SIZE_MASK    0xFFFF0000
>> +#define GXBB_AO_MEM_SIZE_SHIFT    16
>> +#define GXBB_AO_BL31_RSVMEM_SIZE_MASK    0xFFFF0000
>> +#define GXBB_AO_BL31_RSVMEM_SIZE_SHIFT    16
>> +#define GXBB_AO_BL32_RSVMEM_SIZE_MASK    0xFFFF
>> +
>>  /* Peripherals registers */
>>  #define GXBB_PERIPHS_ADDR(off)    (GXBB_PERIPHS_BASE + ((off) << 2))
>>
>> diff --git a/arch/arm/mach-meson/board.c b/arch/arm/mach-meson/board.c
>> index e89c6aa..24733e1 100644
>> --- a/arch/arm/mach-meson/board.c
>> +++ b/arch/arm/mach-meson/board.c
>> @@ -11,6 +11,9 @@
>>  #include <asm/arch/sm.h>
>>  #include <asm/armv8/mmu.h>
>>  #include <asm/unaligned.h>
>> +#include <linux/sizes.h>
>> +#include <efi_loader.h>
>> +#include <asm/io.h>
>>
>>  DECLARE_GLOBAL_DATA_PTR;
>>
>> @@ -34,16 +37,114 @@ int dram_init(void)
>>      return 0;
>>  }
>>
>> -int dram_init_banksize(void)
>> +phys_size_t get_effective_memsize(void)
>>  {
>> -    /* Reserve first 16 MiB of RAM for firmware */
>> -    gd->bd->bi_dram[0].start = 0x1000000;
>> -    gd->bd->bi_dram[0].size  = 0xf000000;
>> -    /* Reserve 2 MiB for ARM Trusted Firmware (BL31) */
>> -    gd->bd->bi_dram[1].start = 0x10000000;
>> -    gd->bd->bi_dram[1].size  = gd->ram_size - 0x10200000;
>> -    return 0;
>> +    /* Size is reported in MiB, convert it in bytes */
>> +    return ((readl(GXBB_AO_SEC_GP_CFG0) & GXBB_AO_MEM_SIZE_MASK)
>> +            >> GXBB_AO_MEM_SIZE_SHIFT) * SZ_1M;
>> +}
>> +
>> +#ifdef CONFIG_MESON_GXBB
>> +/*
>> + * Early Meson GXBB Firmware revision did not provide the reserved
>> + * memory zones in the registers, keep fixed memory zone handling.
>> + */
>> +
>> +void ft_cpu_setup(void *fdt, bd_t *bd)
>> +{
>> +    int ret;
>> +
>> +    /* Add first 16MiB reserved zone */
>> +    ret = fdt_add_mem_rsv(fdt, 0, GXBB_FIRMWARE_MEM_SIZE);
>> +    if (ret)
>> +        printf("Could not reserve zone @ 0x0\n");
>> +
>> +#if defined(CONFIG_EFI_LOADER)
>> +    efi_add_memory_map(0, ALIGN(GXBB_FIRMWARE_MEM_SIZE, EFI_PAGE_SIZE)
>> +                >> EFI_PAGE_SHIFT,
>> +               EFI_RESERVED_MEMORY_TYPE, false);
>> +#endif
> 
> Could you make a sub function that does most of this and then have
> only one set of #if defined ?

Seems a good idea.

> 
> Would anyone mind if efi_add_memory_map had a default 'null' implementation
> if !CONFIG_EFI_LOADE>
>> +
>> +    /* Add BL31 reserved zone */
>> +    ret = fdt_add_mem_rsv(fdt, 0x10000000, 0x200000);
>> +    if (ret)
>> +        printf("Could not reserve BL1 zone @ 0x10000000\n");
>> +
>> +#if defined(CONFIG_EFI_LOADER)
>> +    efi_add_memory_map(0x10000000,
>> +               ALIGN(0x200000, EFI_PAGE_SIZE)
>> +                >> EFI_PAGE_SHIFT,
>> +               EFI_RESERVED_MEMORY_TYPE, false);
>> +#endif
>> +}
>> +#endif
> 
> Can we reduce the pre-processor load here, I'm not even sure
> we're testing the entire file can be compiled.
> 

Well, the 2 uses-cases are very different... but I can try to rework a little.

>> +
>> +#ifdef CONFIG_MESON_GXL
> 
> you're mixing #ifdef and #if defined.

Will fix.

> 
>> +void ft_cpu_setup(void *fdt, bd_t *bd)
>> +{
>> +    u64 bl31_size, bl31_start;
>> +    u64 bl32_size, bl32_start;
>> +    u32 reg;
>> +    int ret;
>> +
>> +    /*
>> +     * Get ARM Trusted Firmware reserved memory zones in :
>> +     * - AO_SEC_GP_CFG3: bl32 & bl31 size in KiB, can be 0
>> +     * - AO_SEC_GP_CFG5: bl31 physical start address, can be NULL
>> +     * - AO_SEC_GP_CFG4: bl32 physical start address, can be NULL
>> +     */
>> +
>> +    reg = readl(GXBB_AO_SEC_GP_CFG3);
>> +
>> +    bl31_size = ((reg & GXBB_AO_BL31_RSVMEM_SIZE_MASK)
>> +            >> GXBB_AO_BL31_RSVMEM_SIZE_SHIFT) * SZ_1K;
>> +    bl32_size = (reg & GXBB_AO_BL32_RSVMEM_SIZE_MASK) * SZ_1K;
>> +
>> +    bl31_start = readl(GXBB_AO_SEC_GP_CFG5);
>> +    bl32_start = readl(GXBB_AO_SEC_GP_CFG4);
>> +
>> +    /* Add first 16MiB reserved zone */
>> +    ret = fdt_add_mem_rsv(fdt, 0, GXBB_FIRMWARE_MEM_SIZE);
>> +    if (ret)
>> +        printf("Could not reserve zone @ 0x0\n");
>> +
>> +#if defined(CONFIG_EFI_LOADER)
>> +    efi_add_memory_map(0, ALIGN(GXBB_FIRMWARE_MEM_SIZE, EFI_PAGE_SIZE)
>> +                >> EFI_PAGE_SHIFT,
>> +               EFI_RESERVED_MEMORY_TYPE, false);
>> +#endif
>> +
>> +    /* Add BL31 reserved zone */
>> +    if (bl31_start && bl31_size) {
>> +        ret = fdt_add_mem_rsv(fdt, bl31_start, bl31_size);
>> +        if (ret)
>> +            printf("Could not reserve BL1 zone @ 0x%llx\n",
>> +                   bl31_start);
>> +
>> +#if defined(CONFIG_EFI_LOADER)
>> +        efi_add_memory_map(bl31_start,
>> +                   ALIGN(bl31_size, EFI_PAGE_SIZE)
>> +                    >> EFI_PAGE_SHIFT,
>> +                   EFI_RESERVED_MEMORY_TYPE, false);
>> +#endif
>> +    }
>> +
>> +    /* Add BL32 reserved zone */
>> +    if (bl32_start && bl32_size) {
>> +        ret = fdt_add_mem_rsv(fdt, bl32_start, bl32_size);
>> +        if (ret)
>> +            printf("Could not reserve BL2 zone @ 0x%llx\n",
>> +                   bl32_start);
>> +
>> +#if defined(CONFIG_EFI_LOADER)
>> +        efi_add_memory_map(bl32_start,
>> +                   ALIGN(bl32_size, EFI_PAGE_SIZE)
>> +                    >> EFI_PAGE_SHIFT,
>> +                   EFI_RESERVED_MEMORY_TYPE, false);
>> +#endif
>> +    }
>>  }
>> +#endif
>>
>>  void reset_cpu(ulong addr)
>>  {
>> diff --git a/board/amlogic/odroid-c2/odroid-c2.c
>> b/board/amlogic/odroid-c2/odroid-c2.c
>> index eac04d8..a9ca34c 100644
>> --- a/board/amlogic/odroid-c2/odroid-c2.c
>> +++ b/board/amlogic/odroid-c2/odroid-c2.c
>> @@ -60,3 +60,10 @@ int misc_init_r(void)
>>
>>      return 0;
>>  }
>> +
>> +int ft_board_setup(void *blob, bd_t *bd)
>> +{
>> +    ft_cpu_setup(blob, bd);
>> +
>> +    return 0;
>> +}
>> diff --git a/board/amlogic/p212/p212.c b/board/amlogic/p212/p212.c
>> index ece8096..abd4f76 100644
>> --- a/board/amlogic/p212/p212.c
>> +++ b/board/amlogic/p212/p212.c
>> @@ -56,3 +56,10 @@ int misc_init_r(void)
>>
>>      return 0;
>>  }
>> +
>> +int ft_board_setup(void *blob, bd_t *bd)
>> +{
>> +    ft_cpu_setup(blob, bd);
>> +
>> +    return 0;
>> +}
>> diff --git a/configs/odroid-c2_defconfig b/configs/odroid-c2_defconfig
>> index f7f8016..4615e03 100644
>> --- a/configs/odroid-c2_defconfig
>> +++ b/configs/odroid-c2_defconfig
>> @@ -15,6 +15,7 @@ CONFIG_CMD_GPIO=y
>>  CONFIG_CMD_MMC=y
>>  # CONFIG_CMD_SETEXPR is not set
>>  CONFIG_OF_CONTROL=y
>> +CONFIG_OF_BOARD_SETUP=y
>>  CONFIG_NET_RANDOM_ETHADDR=y
>>  CONFIG_DM_GPIO=y
>>  CONFIG_DM_MMC=y
>> diff --git a/configs/p212_defconfig b/configs/p212_defconfig
>> index d4b5349..b6e788b 100644
>> --- a/configs/p212_defconfig
>> +++ b/configs/p212_defconfig
>> @@ -17,6 +17,7 @@ CONFIG_CMD_MMC=y
>>  CONFIG_CMD_GPIO=y
>>  # CONFIG_CMD_SETEXPR is not set
>>  CONFIG_OF_CONTROL=y
>> +CONFIG_OF_BOARD_SETUP=y
>>  CONFIG_DM_GPIO=y
>>  CONFIG_DM_MMC=y
>>  CONFIG_MMC_MESON_GX=y
>> diff --git a/include/configs/meson-gxbb-common.h
>> b/include/configs/meson-gxbb-common.h
>> index d88d42d..c2b306a 100644
>> --- a/include/configs/meson-gxbb-common.h
>> +++ b/include/configs/meson-gxbb-common.h
>> @@ -10,7 +10,7 @@
>>
>>  #define CONFIG_CPU_ARMV8
>>  #define CONFIG_REMAKE_ELF
>> -#define CONFIG_NR_DRAM_BANKS        2
>> +#define CONFIG_NR_DRAM_BANKS        1
>>  #define CONFIG_ENV_SIZE            0x2000
>>  #define CONFIG_SYS_MAXARGS        32
>>  #define CONFIG_SYS_MALLOC_LEN        (32 << 20)
> 




More information about the linux-amlogic mailing list