[PATCH 3/5] ARM64: dts: meson-gxbb-p20x: add reset for the ethernet PHY

Martin Blumenstingl martin.blumenstingl at googlemail.com
Tue Jan 17 13:26:33 PST 2017


On Tue, Jan 17, 2017 at 8:22 PM, Jerome Brunet <jbrunet at baylibre.com> wrote:
> On Sat, 2016-12-03 at 00:47 +0100, Martin Blumenstingl wrote:
>> This resets the ethernet PHY during boot to get the PHY into a
>> "clean"
>> state. While here also specify the phy-handle of the ethmac node to
>> make the PHY configuration similar to the one we have on GXL devices.
>>
>> Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.co
>> m>
>> Tested-by: Neil Armstrong <narmstrong at baylibre.com>
>> ---
>>  arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi | 15
>> +++++++++++++++
>>  1 file changed, 15 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
>> b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
>> index 203be28..2abc553 100644
>> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
>> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi
>> @@ -134,10 +134,25 @@
>>       pinctrl-names = "default";
>>  };
>>
>> +&mdio0 {
>> +     ethernet_phy0: ethernet-phy at 0 {
>> +             compatible = "ethernet-phy-ieee802.3-c22";
>> +             reg = <0>;
>
> Sorry for the late reply.
> I just tried on the p200 and this patch (serie) breaks the network on
> it. The PHY is not detected anymore.
>
> From the KSZ9031 Datasheet : "PHY Address 0h is supported as the unique
> PHY address only; it is not supported as the broadcast PHY address
> [...]"
>
> So we can't just use the broadcast address here:
> reg should be <3>.
OK, I'll fix that in a follow-up. as mentioned in the other thread:
can you confirm that the PHY ID is 0x00221620?
It seems that I also broke meson-gxbb-nexbox-a95x.dts with that series
(no idea why that slipped through): according to the photos from
Neil's wiki [0] this seems to use an IC+ 10/100 ethernet PHY (probably
an IP101A)

>> +     };
>> +};
>> +
>>  &ethmac {
>>       status = "okay";
>>       pinctrl-0 = <&eth_rgmii_pins>;
>>       pinctrl-names = "default";
>> +
>> +     phy-handle = <&ethernet_phy0>;
>> +
>> +     snps,reset-gpio = <&gpio GPIOZ_14 0>;
>> +     snps,reset-delays-us = <0 10000 1000000>;
>> +     snps,reset-active-low;
>> +
>> +     phy-mode = "rgmii";
>
> We can't define this in p20x. actually the p201 uses an rmii.
> I have not idea about gpio reset, or the phy address for the p201.
>
> I suppose it would be better to move this to meson-gxbb_p200.dts
>
> I don't know if anybody has a p201, but until we can confirm a working
> Ethernet configuration, we should probably drop it for the p201
>
> Of course the problem was already there before this patch ...
indeed, that seems to be a problem.
the GXBB Nexbox A95x I mentioned above is based on the p201 board.
Amlogic's .dts also toggles GPIOZ_14 for it: [1]
chances are high that it also features an IP101A PHY (this is pure
speculation though).

I propose four patches to fix all this situation:
- add the GPIOZ_14 reset and an ethernet_phy0 (with reg = <0>) to
meson-gxbb-nexbox-a95x.dts
- add the ethernet_phy0 node with reg = <0> (and ideally I also want
to include the KSZ9031 PHY ID) to meson-gxbb-p200.dtsi along with
phy-mode = "rgmii"
- add the ethernet_phy0 node with reg = <0> (without any PHY ID as we
don't know which one is used) to meson-gxbb-p201.dtsi along with
phy-mode = "rgmii"
- remove "phy-mode" and ethernet_phy0 from meson-gxbb-p20x.dtsi and
add a comment that both, the RGMII and the RMII PHY have GPIOZ_14
connected to their reset line

does that make sense?


Regards,
Martin


[0] https://github.com/superna9999/linux/wiki/Boards#nexbox-a95x-s905
[1] https://github.com/khadas/linux/blob/Vim/arch/arm64/boot/dts/amlogic/gxbb_p201.dts#L186



More information about the linux-amlogic mailing list