[RFT net-next v3 0/5] dwmac-meson8b: RGMII clock fixes for Meson8b
Emiliano Ingrassia
ingrassia at epigenesys.com
Fri Dec 29 15:00:58 PST 2017
Hi Jerome, Hi Martin,
On Fri, Dec 29, 2017 at 07:04:23PM +0100, Jerome Brunet wrote:
> On Fri, 2017-12-29 at 02:31 +0100, Emiliano Ingrassia wrote:
> > Hi Martin, Hi Dave,
> >
> > On Thu, Dec 28, 2017 at 11:21:23PM +0100, Martin Blumenstingl wrote:
> > > Hi Dave,
> > >
> > > please do not apply this series until it got a Tested-by from Emiliano.
> > >
> > >
> > > Hi Emiliano,
> > >
> > > you reported [0] that you couldn't get dwmac-meson8b to work on your
> > > Odroid-C1. With your findings (register dumps, clk_summary output, etc.)
> > > I think I was able to find a fix: it consists of two patches (which you
> > > find in this series)
> > >
> > > Unfortunately I don't have any Meson8b boards with RGMII PHY so I could
> > > only partially test this (I could only check if the clocks were
> > > calculated correctly when using a dummy 500002394Hz input clock instead
> > > of MPLL2).
> > >
> > > Could you please give this series a try and let me know about the
> > > results?
> > > You obviously still need your two "ARM: dts: meson8b" patches which
> > > - add the amlogic,meson8b-dwmac" compatible to meson8b.dtsi
> > > - enable Ethernet on the Odroid-C1
> > >
> > > When testing on Meson8b this also needs a fix for the MPLL clock driver:
> > > "clk: meson: mpll: use 64-bit maths in params_from_rate", see:
> > > https://patchwork.kernel.org/patch/10131677/
> > >
> > >
> > > I have tested this myself on a Khadas VIM (GXL SoC, internal RMII PHY)
> > > and a Khadas VIM2 (GXM SoC, external RGMII PHY). Both are still working
> > > fine (so let's hope that this also fixes your Meson8b issue :)).
> > >
> > >
> > > changes since v1 at [1]:
> > > - changed the subject of the cover-letter to indicate that this is all
> > > about the RGMII clock
> > > - added PATCH #1 which ensures that we don't unnecessarily change the
> > > parent clocks in RMII mode (and also makes the code easier to
> > > understand)
> > > - changed subject of PATCH #2 (formerly PATCH #1) to state that this
> > > is about the RGMII clock
> > > - added Jerome's Reviewed-by to PATCH #2 (formerly PATCH #1)
> > > - replaced PATCH #3 (formerly PATCH #2) with one that sets
> > > CLK_SET_RATE_PARENT on the mux and thus re-configures the MPLL2 clock
> > > on Meson8b correctly
> > >
> > > changes since v2 at [2]:
> > > - added PATCH #2 to make the following patch easier
> > > - Emiliano reported that there's currently another bug in the
> > > dwmac-meson8b driver which prevents it from working with RGMII PHYs on
> > > Meson8b: bit 10 of the PRG_ETH0 register is configures a clock gate
> > > (instead of a divide by 5 or divide by 10 clock divider). This has not
> > > been visible on GXBB and later due to the input clock which always led
> > > to a selection of "divide by 10" (which is done internally in the IP
> > > block, but the bit actually means "enable RGMII clock output").
> > > PATCH #3 was added to address this issue.
> > > - the commit message of PATCH #4 and #5 (formerly PATCH #2 and #3) were
> > > updated and the patch itself rebased because the m25_div clock was
> > > removed with the new PATCH #3 (so some of the statements were not
> > > valid anymore)
> > >
> >
> > Here is the clk_summary relative to ethernet on Odroid-C1+
> > with this new series applied:
> >
> > xtal 1 1 24000000 0 0
> > sys_pll 0 0 1200000000 0 0
> > cpu_clk 0 0 1200000000 0 0
> > vid_pll 0 0 732000000 0 0
> > fixed_pll 2 2 2550000000 0 0
> > mpll2 1 1 249999701 0 0
> > c9410000.ethernet#m250_sel 1 1 249999701 0 0
> > c9410000.ethernet#m250_div 1 1 249999701 0 0
> > c9410000.ethernet#fixed_div10 1 1 24999970 0 0
> > c9410000.ethernet#m25_en 1 1 24999970 0 0
> >
> > The ethernet prg0 register is set to 0x74A1 which should be correct with
> > respect to the information contained in the S805 SoC manual.
> > Actually, the ethernet is not yet fully functional.
> > Trying to ping the board, I can see ARP request from host to board using
> > tcpdump. However, the host can't see any response.
>
> If the rx path is ok-ish, I suppose the clock setting applied is good.
> Maybe you could try to play with the tx delay (BIT 5-6 of the register) ?
>
Thanks for the suggestion. Finally the ethernet works correctly using 4
ns as tx-delay.
The clock summary is the same reported above. The prg0 ethernet register
value is 0x74c1 as expected.
I would like to thanks Martin for the support!
As soon as this patch series [v3] will be submitted, I'll submit my patch for
the device tree.
Let me know if you have any question.
Thanks again,
Emiliano
> >
> > Following the U-Boot value for prg0 register, which is 0x7d21, I also
> > tried to set bit 11. As expected, this did not have any influence.
> > Another thing that we should check is the "Ethernet Memory PD" (see S805
> > manual - sec. 5.4) register which bits 3-2 enable/disable ethernet
> > normal operation. However, those bits are already cleared by U-Boot.
> >
> > Thank you for the support.
> >
> > Best regards,
> >
> > Emiliano
> >
> > >
> > > [0] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005596.html
> > > [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005848.html
> > > [2] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005861.html
> > >
> > >
> > > Martin Blumenstingl (5):
> > > net: stmmac: dwmac-meson8b: only configure the clocks in RGMII mode
> > > net: stmmac: dwmac-meson8b: simplify generating the clock names
> > > net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration
> > > net: stmmac: dwmac-meson8b: fix setting the RGMII clock on Meson8b
> > > net: stmmac: dwmac-meson8b: propagate rate changes to the parent clock
> > >
> > > .../net/ethernet/stmicro/stmmac/dwmac-meson8b.c | 119 +++++++++++----------
> > > 1 file changed, 63 insertions(+), 56 deletions(-)
> > >
> > > --
> > > 2.15.1
> > >
>
More information about the linux-amlogic
mailing list