[RESEND PATCH v3 2/2] ARM64: dts: meson-axg: add pinctrl DT info for Meson-AXG SoC

Kevin Hilman khilman at baylibre.com
Wed Dec 6 12:18:32 PST 2017


Yixun Lan <yixun.lan at amlogic.com> writes:

> From: Xingyu Chen <xingyu.chen at amlogic.com>
>
> Add new pinctrl DT info for the Amlogic's Meson-AXG SoC.
>
> Reviewed-by: Neil Armstrong <narmstrong at baylibre.com>
> Signed-off-by: Xingyu Chen <xingyu.chen at amlogic.com>
> Signed-off-by: Yixun Lan <yixun.lan at amlogic.com>
> ---
>  arch/arm64/boot/dts/amlogic/meson-axg.dtsi | 44 ++++++++++++++++++++++++++++++
>  1 file changed, 44 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> index 5fc33b76b91c..e0fb860e12c5 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> @@ -9,6 +9,7 @@
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/clock/axg-clkc.h>
>  #include <dt-bindings/clock/axg-aoclkc.h>

This doesn't apply because this aoclkc.h header does not exist in
mainline.

Kevin

> +#include <dt-bindings/gpio/meson-axg-gpio.h>
>  
>  / {
>  	compatible = "amlogic,meson-axg";
> @@ -173,6 +174,32 @@
>  			#mbox-cells = <1>;
>  		};
>  
> +		periphs: periphs at ff634000 {
> +			compatible = "simple-bus";
> +			reg = <0x0 0xff634000 0x0 0x2000>;
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges = <0x0 0x0 0x0 0xff634000 0x0 0x2000>;
> +
> +			pinctrl_periphs: pinctrl at 480 {
> +				compatible = "amlogic,meson-axg-periphs-pinctrl";
> +				#address-cells = <2>;
> +				#size-cells = <2>;
> +				ranges;
> +
> +				gpio: bank at 480 {
> +					reg = <0x0 0x00480 0x0 0x40>,
> +						<0x0 0x004e8 0x0 0x14>,
> +						<0x0 0x00520 0x0 0x14>,
> +						<0x0 0x00430 0x0 0x3c>;
> +					reg-names = "mux", "pull", "pull-enable", "gpio";
> +					gpio-controller;
> +					#gpio-cells = <2>;
> +					gpio-ranges = <&pinctrl_periphs 0 0 86>;
> +				};
> +			};
> +		};
> +
>  		sram: sram at fffc0000 {
>  			compatible = "amlogic,meson-axg-sram", "mmio-sram";
>  			reg = <0x0 0xfffc0000 0x0 0x20000>;
> @@ -209,6 +236,23 @@
>  				};
>  			};
>  
> +			pinctrl_aobus: pinctrl at 14 {
> +				compatible = "amlogic,meson-axg-aobus-pinctrl";
> +				#address-cells = <2>;
> +				#size-cells = <2>;
> +				ranges;
> +
> +				gpio_ao: bank at 14 {
> +					reg = <0x0 0x00014 0x0 0x8>,
> +						<0x0 0x0002c 0x0 0x4>,
> +						<0x0 0x00024 0x0 0x8>;
> +					reg-names = "mux", "pull", "gpio";
> +					gpio-controller;
> +					#gpio-cells = <2>;
> +					gpio-ranges = <&pinctrl_aobus 0 0 15>;
> +				};
> +			};
> +
>  			uart_AO: serial at 3000 {
>  				compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart";
>  				reg = <0x0 0x3000 0x0 0x18>;



More information about the linux-amlogic mailing list