[PATCH v2 1/6] usb: dwc2: add support for Meson8b and GXBB SoCs
John Youn
John.Youn at synopsys.com
Wed Sep 14 11:12:20 PDT 2016
On 9/14/2016 9:11 AM, Kevin Hilman wrote:
> Hi John,
>
> Martin Blumenstingl <martin.blumenstingl at googlemail.com> writes:
>
>> From: Jerome Brunet <jbrunet at baylibre.com>
>>
>> Add compatible strings for amlogic Meson8b and GXBB SoCs with the
>> corresponding configuration parameters.
>>
>> Signed-off-by: Jerome Brunet <jbrunet at baylibre.com>
>> Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
>
> Are you OK with adding this platform for v4.9? I know you mentioned
> you're working on new bindings to replace the current way, but since
> that hasn't been posted AFAICT, it would be nice to get this merged now
> and we can help test the new bindings when you're ready.
>
> If you're OK with that, and with your Ack, I can take merge the driver
> changes through the arm-soc tree along with the rest of the DT patches.
>
Sure. Unfortunately, I wasn't able to complete it for 4.9.
You can add my acked-by on this:
Acked-by: John Youn <johnyoun at synopsys.com>
Regards,
John
> Kevin
>
>> ---
>> Documentation/devicetree/bindings/usb/dwc2.txt | 2 ++
>> drivers/usb/dwc2/platform.c | 34 ++++++++++++++++++++++++++
>> 2 files changed, 36 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt
>> index 20a68bf..2c30a54 100644
>> --- a/Documentation/devicetree/bindings/usb/dwc2.txt
>> +++ b/Documentation/devicetree/bindings/usb/dwc2.txt
>> @@ -10,6 +10,8 @@ Required properties:
>> - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc;
>> - "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs;
>> - "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs;
>> + - "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs;
>> + - "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs;
>> - snps,dwc2: A generic DWC2 USB controller with default parameters.
>> - reg : Should contain 1 register range (address and length)
>> - interrupts : Should contain 1 interrupt
>> diff --git a/drivers/usb/dwc2/platform.c b/drivers/usb/dwc2/platform.c
>> index fc6f525..8f7b34c 100644
>> --- a/drivers/usb/dwc2/platform.c
>> +++ b/drivers/usb/dwc2/platform.c
>> @@ -181,6 +181,38 @@ static const struct dwc2_core_params params_ltq = {
>> .hibernation = -1,
>> };
>>
>> +static const struct dwc2_core_params params_amlogic = {
>> + .otg_cap = DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE,
>> + .otg_ver = -1,
>> + .dma_enable = 1,
>> + .dma_desc_enable = 0,
>> + .dma_desc_fs_enable = 0,
>> + .speed = DWC2_SPEED_PARAM_HIGH,
>> + .enable_dynamic_fifo = 1,
>> + .en_multiple_tx_fifo = -1,
>> + .host_rx_fifo_size = 512,
>> + .host_nperio_tx_fifo_size = 500,
>> + .host_perio_tx_fifo_size = 500,
>> + .max_transfer_size = -1,
>> + .max_packet_count = -1,
>> + .host_channels = 16,
>> + .phy_type = DWC2_PHY_TYPE_PARAM_UTMI,
>> + .phy_utmi_width = -1,
>> + .phy_ulpi_ddr = -1,
>> + .phy_ulpi_ext_vbus = -1,
>> + .i2c_enable = -1,
>> + .ulpi_fs_ls = -1,
>> + .host_support_fs_ls_low_power = -1,
>> + .host_ls_low_power_phy_clk = -1,
>> + .ts_dline = -1,
>> + .reload_ctl = 1,
>> + .ahbcfg = GAHBCFG_HBSTLEN_INCR8 <<
>> + GAHBCFG_HBSTLEN_SHIFT,
>> + .uframe_sched = 0,
>> + .external_id_pin_ctl = -1,
>> + .hibernation = -1,
>> +};
>> +
>> /*
>> * Check the dr_mode against the module configuration and hardware
>> * capabilities.
>> @@ -464,6 +496,8 @@ static const struct of_device_id dwc2_of_match_table[] = {
>> { .compatible = "lantiq,xrx200-usb", .data = ¶ms_ltq },
>> { .compatible = "snps,dwc2", .data = NULL },
>> { .compatible = "samsung,s3c6400-hsotg", .data = NULL},
>> + { .compatible = "amlogic,meson8b-usb", .data = ¶ms_amlogic },
>> + { .compatible = "amlogic,meson-gxbb-usb", .data = ¶ms_amlogic },
>> {},
>> };
>> MODULE_DEVICE_TABLE(of, dwc2_of_match_table);
>
More information about the linux-amlogic
mailing list