[PATCH 5/7] ARM64: meson-gxbb: add USB Nodes

Neil Armstrong narmstrong at baylibre.com
Mon Sep 5 01:00:21 PDT 2016


On 09/05/2016 02:23 AM, Andreas Färber wrote:
> Hi Martin,
> 
> Am 04.09.2016 um 23:31 schrieb Martin Blumenstingl:
>> Add the nodes for the dwc2 USB controller and the related USB PHYs.
>> Currently we force usb0 to host mode because OTG is currently not
>> working in our PHY driver.
>>
>> Signed-off-by: Jerome Brunet <jbrunet at baylibre.com>
>> Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
>> ---
>>  arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 52 +++++++++++++++++++++++++++++
>>  1 file changed, 52 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
>> index 2e8a3d9..02dfc54 100644
>> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
>> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
>> @@ -151,6 +151,34 @@
>>  		#size-cells = <2>;
>>  		ranges;
>>  
>> +		usb-phys at c0000000 {
>> +			compatible = "simple-bus";
>> +			reg = <0x0 0xc0000000 0x0 0x40>;
>> +			#address-cells = <2>;
>> +			#size-cells = <2>;
>> +			ranges = <0x0 0x0 0x0 0xc0000000 0x0 0x40>;
> 
> Does this correspond to any physical bus or could we drop this layer?
> 
>> +
>> +			usb0_phy: usb_phy at 0 {
> 
> phy at 0 to avoid the underscore in node name? dash otherwise.
> If dropping the bus, *phy at c0000000 obviously.
> 
>> +				compatible = "amlogic,meson-gxbb-usb2-phy";
>> +				#phy-cells = <0>;
>> +				reg = <0x0 0x0 0x0 0x20>;
>> +				resets = <&reset 34>;
>> +				clocks = <&clkc CLKID_USB &clkc CLKID_USB0>;
> 
> <&clkc CLKID_USB>, <&clkc CLKID_USB0> please.
> 
>> +				clock-names = "usb_general", "usb";
>> +				status = "disabled";
>> +			};
>> +
>> +			usb1_phy: usb_phy at 20 {
>> +				compatible = "amlogic,meson-gxbb-usb2-phy";
>> +				#phy-cells = <0>;
>> +				reg = <0x0 0x20 0x0 0x20>;
>> +				resets = <&reset 34>;
>> +				clocks = <&clkc CLKID_USB &clkc CLKID_USB1>;
> 
> Ditto
> 
>> +				clock-names = "usb_general", "usb";
>> +				status = "disabled";
>> +			};
>> +		};
>> +
>>  		cbus: cbus at c1100000 {
>>  			compatible = "simple-bus";
>>  			reg = <0x0 0xc1100000 0x0 0x100000>;
>> @@ -496,6 +524,30 @@
>>  			};
>>  		};
>>  
>> +		usb0: usb-controller at c9000000 {
> 
> usb at c9000000 by convention.
> 
>> +			compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
>> +			reg = <0x0 0xc9000000 0x0 0x40000>;
>> +			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&clkc CLKID_USB0_DDR_BRIDGE>;
>> +			clock-names = "otg";
>> +			phys = <&usb0_phy>;
>> +			phy-names = "usb2-phy";
>> +			dr_mode = "host";
>> +			status = "disabled";
>> +		};
>> +
>> +		usb1: usb-controller at c9100000 {
> 
> usb at c9100000
> 
>> +			compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
>> +			reg = <0x0 0xc9100000 0x0 0x40000>;
>> +			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
>> +			clock-names = "otg";
>> +			phys = <&usb1_phy>;
>> +			phy-names = "usb2-phy";
>> +			dr_mode = "host";
>> +			status = "disabled";
>> +		};
>> +
>>  		ethmac: ethernet at c9410000 {
>>  			compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
>>  			reg = <0x0 0xc9410000 0x0 0x10000
> 
> Thanks for the huge progress you guys have been making.
> 
> This patchset will probably clash with Neil's GXL preparations?

My GXL patch can wait USB ;-)

> 
> Regards,
> Andreas
> 

Thanks,
Neil



More information about the linux-amlogic mailing list