[RFC PATCH 1/3] watchdog: Add Meson GXBB Watchdog Driver
Neil Armstrong
narmstrong at baylibre.com
Fri May 27 01:25:20 PDT 2016
On 05/26/2016 03:54 PM, Guenter Roeck wrote:
> On 05/26/2016 12:51 AM, Neil Armstrong wrote:
>> Add watchdog specific driver for Amlogic Meson GXBB SoC.
>>
>
> Wondering - why RFC ?
For these precious comments !
Thanks Guenter.
>
>> Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
>> ---
>> drivers/watchdog/Makefile | 1 +
>> drivers/watchdog/meson_gxbb_wdt.c | 287 ++++++++++++++++++++++++++++++++++++++
>> 2 files changed, 288 insertions(+)
>> create mode 100644 drivers/watchdog/meson_gxbb_wdt.c
>>
>> diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
>> index 9bde095..7679d93 100644
>> --- a/drivers/watchdog/Makefile
>> +++ b/drivers/watchdog/Makefile
[...]
>> +
>> +unsigned int meson_gxbb_wdt_status(struct watchdog_device *wdt_dev)
>> +{
>> + struct meson_gxbb_wdt *data = watchdog_get_drvdata(wdt_dev);
>> +
>> + return !!(readl(data->reg_base + GXBB_WDT_CTRL_REG) & GXBB_WDT_CTRL_EN);
>
> This function is not supposed to return 0/1 but a bit mask with relevant
> WDIOF_bits set. sbsa_gwdt.c is buggy (oops, and I reviewed it ;-), so
> please don't use it as example; it doesn't make much sense to return
> a kernel-only flag to user space.
>
> Overall I would suggest to not implement the function at all. We'll have
> to revisit it - its current implementation in the watchdog core does not
> make much sense and for the most part only returns 0 to user space.
> The only driver implementing it (sbsa) returns a bad value. It is also
> _not_ supposed to return the "watchdog running" status as currently
> implemented (there is no WDIOF_ flag indicating that the watchdog is
> running).
Ok, will remove it.
>> +}
>> +
>> +int meson_gxbb_wdt_ping(struct watchdog_device *wdt_dev)
>> +{
>> + struct meson_gxbb_wdt *data = watchdog_get_drvdata(wdt_dev);
>> +
>> + writel(0, data->reg_base + GXBB_WDT_RSET_REG);
>> +
>> + return 0;
>> +}
>> +
>> +int meson_gxbb_wdt_set_timeout(struct watchdog_device *wdt_dev,
>> + unsigned int timeout)
>> +{
>> + struct meson_gxbb_wdt *data = watchdog_get_drvdata(wdt_dev);
>> +
>> + if (watchdog_active(wdt_dev))
>> + meson_gxbb_wdt_stop(wdt_dev);
>> +
>
> Is the stop/start sequence mandatory ? It leaves the system unprotected
> for a few cycles, so it is undesirable.
No, it's not mandatory, it's a good point.
>> +
>> + data->wdt_dev.parent = &pdev->dev;
>> + data->wdt_dev.info = &meson_gxbb_wdt_info;
>> + data->wdt_dev.ops = &meson_gxbb_wdt_ops;
>> + data->wdt_dev.max_hw_heartbeat_ms = GXBB_WDT_TCNT_SETUP_MASK;
>> + data->wdt_dev.min_hw_heartbeat_ms = 1;
>
> Does the device require a minimum time between heartbeats ?
> Just asking, because you violate it yourself below.
>
> If you want to set the minimum timeout, that would be min_timeout.
Ok, these values are not very clear actually.
>> + data->wdt_dev.timeout = DEFAULT_TIMEOUT;
>> + watchdog_set_drvdata(&data->wdt_dev, data);
>> +
>> + watchdog_init_timeout(&data->wdt_dev, DEFAULT_TIMEOUT, &pdev->dev);
>> +
>
> DEFAULT_TIMEOUT is unnecessary here. Since the default timeout is already set,
> it makes the call useless.
>
>> + ret = watchdog_register_device(&data->wdt_dev);
>> + if (ret)
>> + return ret;
>> +
>> + /* Setup with 1ms timebase */
>> + writel(((clk_get_rate(data->clk) / 1000) & GXBB_WDT_CTRL_DIV_MASK) |
>> + GXBB_WDT_CTRL_EE_RESET |
>> + GXBB_WDT_CTRL_CLK_EN |
>> + GXBB_WDT_CTRL_CLKDIV_EN,
>> + data->reg_base + GXBB_WDT_CTRL_REG);
>> + meson_gxbb_wdt_set_timeout(&data->wdt_dev, data->wdt_dev.timeout);
>
> set_timeout already calls the ping function. Also, the functions should be called
> prior to watchdog registration to avoid race conditions.
>
>> + meson_gxbb_wdt_ping(&data->wdt_dev);
>
> This is unusual. If the watchdog can be already running, it might make sense
> to tell the core about it (set WDOG_HW_RUNNING in the status field), so it
> can send heartbeats until user space opens the device.
Yes, since meson_gxbb_wdt_set_timeout() already ping, this is useless.
More information about the linux-amlogic
mailing list