[PATCH v4 4/6] media: rc: meson-ir: Add support for newer versions of the IR decoder
Martin Blumenstingl
martin.blumenstingl at googlemail.com
Fri Aug 19 14:55:45 PDT 2016
From: Neil Armstrong <narmstrong at baylibre.com>
Newer SoCs (Meson 8b and GXBB) are using REG2 (offset 0x20) instead of
REG1 to configure the decoder mode. This makes it necessary to
introduce new bindings so the driver knows which register has to be
used.
Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
---
drivers/media/rc/meson-ir.c | 29 ++++++++++++++++++++++++-----
1 file changed, 24 insertions(+), 5 deletions(-)
diff --git a/drivers/media/rc/meson-ir.c b/drivers/media/rc/meson-ir.c
index fcc3b82..003fff0 100644
--- a/drivers/media/rc/meson-ir.c
+++ b/drivers/media/rc/meson-ir.c
@@ -24,6 +24,7 @@
#define DRIVER_NAME "meson-ir"
+/* valid on all Meson platforms */
#define IR_DEC_LDR_ACTIVE 0x00
#define IR_DEC_LDR_IDLE 0x04
#define IR_DEC_LDR_REPEAT 0x08
@@ -32,12 +33,21 @@
#define IR_DEC_FRAME 0x14
#define IR_DEC_STATUS 0x18
#define IR_DEC_REG1 0x1c
+/* only available on Meson 8b and newer */
+#define IR_DEC_REG2 0x20
#define REG0_RATE_MASK (BIT(11) - 1)
-#define REG1_MODE_MASK (BIT(7) | BIT(8))
-#define REG1_MODE_NEC (0 << 7)
-#define REG1_MODE_GENERAL (2 << 7)
+#define DECODE_MODE_NEC 0x0
+#define DECODE_MODE_RAW 0x2
+
+/* Meson 6b uses REG1 to configure the mode */
+#define REG1_MODE_MASK GENMASK(8, 7)
+#define REG1_MODE_SHIFT 7
+
+/* Meson 8b / GXBB use REG2 to configure the mode */
+#define REG2_MODE_MASK GENMASK(3, 0)
+#define REG2_MODE_SHIFT 0
#define REG1_TIME_IV_SHIFT 16
#define REG1_TIME_IV_MASK ((BIT(13) - 1) << REG1_TIME_IV_SHIFT)
@@ -158,8 +168,15 @@ static int meson_ir_probe(struct platform_device *pdev)
/* Reset the decoder */
meson_ir_set_mask(ir, IR_DEC_REG1, REG1_RESET, REG1_RESET);
meson_ir_set_mask(ir, IR_DEC_REG1, REG1_RESET, 0);
- /* Set general operation mode */
- meson_ir_set_mask(ir, IR_DEC_REG1, REG1_MODE_MASK, REG1_MODE_GENERAL);
+
+ /* Set general operation mode (= raw/software decoding) */
+ if (of_device_is_compatible(node, "amlogic,meson6-ir"))
+ meson_ir_set_mask(ir, IR_DEC_REG1, REG1_MODE_MASK,
+ DECODE_MODE_RAW << REG1_MODE_SHIFT);
+ else
+ meson_ir_set_mask(ir, IR_DEC_REG2, REG2_MODE_MASK,
+ DECODE_MODE_RAW << REG2_MODE_SHIFT);
+
/* Set rate */
meson_ir_set_mask(ir, IR_DEC_REG0, REG0_RATE_MASK, MESON_TRATE - 1);
/* IRQ on rising and falling edges */
@@ -197,6 +214,8 @@ static int meson_ir_remove(struct platform_device *pdev)
static const struct of_device_id meson_ir_match[] = {
{ .compatible = "amlogic,meson6-ir" },
+ { .compatible = "amlogic,meson8b-ir" },
+ { .compatible = "amlogic,meson-gxbb-ir" },
{ },
};
--
2.9.3
More information about the linux-amlogic
mailing list