[PATCH] libertas/sdio: set ECSI and SCSI bits for 1-bit transfers

[Dan Williams]

On Tue, 2010-03-30 at 19:38 +0200, Daniel Mack wrote:
> When operating in 1-bit mode, SDAT1 is used as dedicated interrupt line.
> However, the 8686 will only drive this line when the ECSI and SCSI bits
> are set in the CCCR_IF register.

While this looks fine enough to me, I don't have enough knowledge of the
SDIO stack to know whether or not this would be considered a layering
violation or not.  Given that I don't think there's an active maintainer
for the SDIO subsystem though, I'd say it's fine enough for me...

Any thoughts David since it appears to be at least somewhat SPI related?

Acked-by: Dan Williams <dcbw at redhat.com>

> Thanks to Alagu Sankar for pointing me in the right direction.
> 
> Signed-off-by: Daniel Mack <daniel at caiaq.de>
> Cc: Alagu Sankar <alagusankar at embwise.com>
> Cc: Volker Ernst <volker.ernst at txtr.com>
> Cc: Dan Williams <dcbw at redhat.com>
> Cc: John W. Linville <linville at tuxdriver.com>
> Cc: Holger Schurig <hs4233 at mail.mn-solutions.de>
> Cc: Bing Zhao <bzhao at marvell.com>
> Cc: libertas-dev at lists.infradead.org
> Cc: linux-wireless at vger.kernel.org
> Cc: linux-mmc at vger.kernel.org
> ---
>  drivers/net/wireless/libertas/if_sdio.c |   24 ++++++++++++++++++++++++
>  include/linux/mmc/sdio.h                |    2 ++
>  2 files changed, 26 insertions(+), 0 deletions(-)
> 
> diff --git a/drivers/net/wireless/libertas/if_sdio.c b/drivers/net/wireless/libertas/if_sdio.c
> index 7a73f62..d3170f2 100644
> --- a/drivers/net/wireless/libertas/if_sdio.c
> +++ b/drivers/net/wireless/libertas/if_sdio.c
> @@ -34,6 +34,8 @@
>  #include <linux/mmc/card.h>
>  #include <linux/mmc/sdio_func.h>
>  #include <linux/mmc/sdio_ids.h>
> +#include <linux/mmc/sdio.h>
> +#include <linux/mmc/host.h>
>  
>  #include "host.h"
>  #include "decl.h"
> @@ -942,6 +944,7 @@ static int if_sdio_probe(struct sdio_func *func,
>  	int ret, i;
>  	unsigned int model;
>  	struct if_sdio_packet *packet;
> +	struct mmc_host *host = func->card->host;
>  
>  	lbs_deb_enter(LBS_DEB_SDIO);
>  
> @@ -1022,6 +1025,27 @@ static int if_sdio_probe(struct sdio_func *func,
>  	if (ret)
>  		goto disable;
>  
> +	/* For 1-bit transfers, we need to enable the interrupt flags in
> +	 * the CCCR register. Temporarily set the function number to 0
> +	 * for that. */
> +	if ((host->caps & MMC_CAP_SDIO_IRQ) &&
> +	    (host->ios.bus_width == MMC_BUS_WIDTH_1)) {
> +		unsigned int num = func->num;
> +		u8 reg;
> +
> +		func->num = 0;
> +		reg = sdio_readb(func, SDIO_CCCR_IF, &ret);
> +		if (ret)
> +			goto release_int;
> +
> +		reg |= SDIO_BUS_ECSI | SDIO_BUS_SCSI;
> +		sdio_writeb(func, reg, SDIO_CCCR_IF, &ret);
> +		if (ret)
> +			goto release_int;
> +
> +		func->num = num;
> +	}
> +
>  	card->ioport = sdio_readb(func, IF_SDIO_IOPORT, &ret);
>  	if (ret)
>  		goto release_int;
> diff --git a/include/linux/mmc/sdio.h b/include/linux/mmc/sdio.h
> index 0ebaef5..329a8fa 100644
> --- a/include/linux/mmc/sdio.h
> +++ b/include/linux/mmc/sdio.h
> @@ -94,6 +94,8 @@
>  
>  #define  SDIO_BUS_WIDTH_1BIT	0x00
>  #define  SDIO_BUS_WIDTH_4BIT	0x02
> +#define  SDIO_BUS_ECSI		0x20	/* Enable continuous SPI interrupt */
> +#define  SDIO_BUS_SCSI		0x40	/* Support continuous SPI interrupt */
>  
>  #define  SDIO_BUS_ASYNC_INT	0x20
>