[PATCH 1/2] libertas: if_spi: add ability to call board specific setup/teardown methods

[Mike Rapoport]

In certain cases it is required to perform board specific actions
before activating libertas G-SPI interface. These actions may include
power up of the chip, GPIOs setup, proper pin-strapping and SPI
controller config.
This patch adds ability to call board specific setup/teardown methods

Signed-off-by: Mike Rapoport <mike at compulab.co.il>
---
 drivers/net/wireless/libertas/if_spi.c |   15 +++++++++++++++
 include/linux/spi/libertas_spi.h       |    7 +++++++
 2 files changed, 22 insertions(+), 0 deletions(-)

diff --git a/drivers/net/wireless/libertas/if_spi.c b/drivers/net/wireless/libertas/if_spi.c
index 7c02ea3..07311e7 100644
--- a/drivers/net/wireless/libertas/if_spi.c
+++ b/drivers/net/wireless/libertas/if_spi.c
@@ -42,6 +42,7 @@ struct if_spi_packet {
 struct if_spi_card {
 	struct spi_device		*spi;
 	struct lbs_private		*priv;
+	struct libertas_spi_platform_data *pdata;

 	char				helper_fw_name[FIRMWARE_NAME_MAX];
 	char				main_fw_name[FIRMWARE_NAME_MAX];
@@ -1022,6 +1023,17 @@ static int __devinit if_spi_probe(struct spi_device *spi)

 	lbs_deb_enter(LBS_DEB_SPI);

+	if (!pdata) {
+		err = -EINVAL;
+		goto out;
+	}
+
+	if (pdata->setup) {
+		err = pdata->setup(spi);
+		if (err)
+			goto out;
+	}
+
 	/* Allocate card structure to represent this specific device */
 	card = kzalloc(sizeof(struct if_spi_card), GFP_KERNEL);
 	if (!card) {
@@ -1029,6 +1041,7 @@ static int __devinit if_spi_probe(struct spi_device *spi)
 		goto out;
 	}
 	spi_set_drvdata(spi, card);
+	card->pdata = pdata;
 	card->spi = spi;
 	card->gpio_cs = pdata->gpio_cs;
 	card->prev_xfer_time = jiffies;
@@ -1158,6 +1171,8 @@ static int __devexit libertas_spi_remove(struct spi_device *spi)
 	if_spi_terminate_spi_thread(card);
 	lbs_remove_card(priv); /* will call free_netdev */
 	gpio_free(card->gpio_cs);
+	if (card->pdata->teardown)
+		card->pdata->teardown(spi);
 	free_if_spi_card(card);
 	lbs_deb_leave(LBS_DEB_SPI);
 	return 0;
diff --git a/include/linux/spi/libertas_spi.h b/include/linux/spi/libertas_spi.h
index ada71b4..79506f5 100644
--- a/include/linux/spi/libertas_spi.h
+++ b/include/linux/spi/libertas_spi.h
@@ -10,6 +10,9 @@
  */
 #ifndef _LIBERTAS_SPI_H_
 #define _LIBERTAS_SPI_H_
+
+struct spi_device;
+
 struct libertas_spi_platform_data {
 	/* There are two ways to read data from the WLAN module's SPI
 	 * interface. Setting 0 or 1 here controls which one is used.
@@ -21,5 +24,9 @@ struct libertas_spi_platform_data {

 	/* GPIO number to use as chip select */
 	u16 gpio_cs;
+
+	/* Board specific setup/teardown */
+	int (*setup)(struct spi_device *spi);
+	int (*teardown)(struct spi_device *spi);
 };
 #endif
-- 
1.5.6.4



-- 
Sincerely yours,
Mike.