[LEDE-DEV] [PATCH 3/3] lantiq: add support for AVM FRITZ!Box 7412
John Crispin
john at phrozen.org
Fri Mar 9 11:56:25 PST 2018
On 09/03/18 20:55, John Crispin wrote:
>
>
> On 09/03/18 20:17, Valentin Spreckels wrote:
>> Specification:
>> - SoC: Lantiq VRX 220
>> - CPU Cores: 2x MIPS 34Kc at 500 MHz
>> - RAM: 128 MiB 250 MHz
>> - Storage: 128 MiB NAND flash
>> - Ethernet: built-in Fast Ethernet switch, only port 2 is used
>> - Wireless: Atheros AR9287-BL1A b/g/n with 2 pcb antennas
>> - Modem: built-in A/VDSL2 modem
>> - DECT: Dialog SC14441
>> - LEDs: 1 two-color, 4 one-color
>> - Buttons: 2
>> - FXS: 1 port via TAE or RJ12 connector
>>
>> Working:
>> - ethernet
>> - wifi
>> - leds
>> - buttons
>> - dsl
>>
>> Not working:
>> - Second cpu core
>> - FXS
>> - DECT
>>
>> Installation:
>>
>> 1. Use the eva_ramboot.py script to load an initramfs image on the
>> device. Run it a few seconds after turning the device on.
>> $ scripts/flashing eva_ramboot 192.168.178.1
>> bin/targets/lantiq/xrx200/openwrt-lantiq-xrx200-avm_fritz7412-initramfs-kernel.bin
>>
>> If it fails to find the device try the ip address 169.254.120.1.
>> (Firmware updates or the recovery tool apparently change it.)
>>
>> 2. The device will load it in ram and boot it. You can reach it under
>> the openwrt default ip address 192.168.1.1.
>>
>> 3. Check if the key linux_fs_start is not set to 1 in tffs:
>> $ fritz_tffs_nand -d /dev/mtd1 -n linux_fs_start
>> If it is set to 1, the bootloader will select the wrong set of
>> partitions. Restart the box and install an FritzOS upgrade or do a
>> recovery. Afterwards start again at step 1.
>>
>> 4. Run sysupgrade to persistently install OpenWRT.
>>
>> Signed-off-by: Valentin Spreckels
>> <Valentin.Spreckels at Informatik.Uni-Oldenburg.DE>
>> ---
>> .../linux/lantiq/base-files/etc/board.d/02_network | 8 +
>> .../etc/hotplug.d/firmware/12-ath9k-eeprom | 3 +
>> .../lantiq/base-files/lib/upgrade/platform.sh | 2 +-
>> .../files-4.14/arch/mips/boot/dts/FRITZ7412.dts | 241
>> ++++++++++++++++++++
>> .../files-4.9/arch/mips/boot/dts/FRITZ7412.dts | 242
>> +++++++++++++++++++++
>> .../lantiq/files-4.9/arch/mips/boot/dts/vr9.dtsi | 2 +-
>> target/linux/lantiq/image/Makefile | 13 ++
>> 7 files changed, 509 insertions(+), 2 deletions(-)
>> create mode 100644
>> target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7412.dts
>> create mode 100644
>> target/linux/lantiq/files-4.9/arch/mips/boot/dts/FRITZ7412.dts
>>
>> diff --git a/target/linux/lantiq/base-files/etc/board.d/02_network
>> b/target/linux/lantiq/base-files/etc/board.d/02_network
>> index ca974b071e..defdc1a94d 100755
>> --- a/target/linux/lantiq/base-files/etc/board.d/02_network
>> +++ b/target/linux/lantiq/base-files/etc/board.d/02_network
>> @@ -154,6 +154,14 @@ avm,fritz7360sl)
>> "0:lan:3" "1:lan:4" "2:lan:2" "4:lan:1" "6t at eth0"
>> ;;
>> +avm,fritz7412)
>> + tffsdev=$(find_mtd_chardev "nand-tffs")
>> + annex="b"
>> + lan_mac=$(/usr/bin/fritz_tffs_nand -d $tffsdev -n maca)
>> + wan_mac=$(/usr/bin/fritz_tffs_nand -d $tffsdev -n macdsl)
> dont use absolute paths please ...
>> + ucidef_set_interface_lan 'eth0'
>> + ;;
>> +
>> siemens,gigaset-sx76x)
>> annex="b"
>> ucidef_add_switch "switch0" \
>> diff --git
>> a/target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom
>> b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom
>> index 498a509012..68181c7b87 100644
>> ---
>> a/target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom
>> +++
>> b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom
>> @@ -141,6 +141,9 @@ case "$FIRMWARE" in
>> avm,fritz3370|avm,fritz7320|avm,fritz7360sl)
>> ath9k_eeprom_extract "urlader" 2437 0
>> ;;
>> + avm,fritz7412)
>> + /usr/bin/fritz_cal_extract -i 1 -s 0x1e000 -e 0x207
>> -l 4096 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader")
> absolute path ...
>> + ;;
>> tplink,tdw8970|tplink,tdw8980)
>> ath9k_eeprom_extract "boardconfig" 135168 0
>> ;;
>> diff --git a/target/linux/lantiq/base-files/lib/upgrade/platform.sh
>> b/target/linux/lantiq/base-files/lib/upgrade/platform.sh
>> index 2e58cb799a..7a43e7e12e 100755
>> --- a/target/linux/lantiq/base-files/lib/upgrade/platform.sh
>> +++ b/target/linux/lantiq/base-files/lib/upgrade/platform.sh
>> @@ -9,7 +9,7 @@ platform_do_upgrade() {
>> local board=$(board_name)
>> case "$board" in
>> -
>> bt,homehub-v2b|bt,homehub-v3a|bt,homehub-v5a|zyxel,p-2812hnu-f1|zyxel,p-2812hnu-f3)
>> +
>> avm,fritz7412|bt,homehub-v2b|bt,homehub-v3a|bt,homehub-v5a|zyxel,p-2812hnu-f1|zyxel,p-2812hnu-f3)
> please turn this into |\
> multi|\
> line)
>
>> nand_do_upgrade $1
>> ;;
>> *)
>> diff --git
>> a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7412.dts
>> b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7412.dts
>> new file mode 100644
>> index 0000000000..5bcd140520
>> --- /dev/null
>> +++ b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7412.dts
>
> i'll leave the dts review to mkresin, there is a newline spacing issue
> for sure. :-)
>
> all in all, thanks, nice patch series
>
> John
>> @@ -0,0 +1,241 @@
>> +/dts-v1/;
>> +
>> +#include "vr9.dtsi"
>> +
>> +#include <dt-bindings/input/input.h>
>> +#include <dt-bindings/mips/lantiq_rcu_gphy.h>
>> +
>> +/ {
>> + compatible = "avm,fritz7412", "lantiq,xway", "lantiq,vr9";
>> + model = "1&1 DSL-Modem / 1&1 WLAN-Router";
>> +
>> + chosen {
>> + bootargs = "console=ttyLTQ0,115200 mem=126M
>> vpe1_load_addr=0x87e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp";
>> + };
>> +
>> + aliases {
>> + led-boot = &power_green;
>> + led-failsafe = &power_red;
>> + led-running = &power_green;
>> +
>> + led-dsl = &info;
>> + led-wifi = &wifi;
>> + };
>> +
>> + memory at 0 {
>> + reg = <0x0 0x8000000>;
>> + };
>> +
>> + gpio-keys-polled {
>> + compatible = "gpio-keys-polled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + poll-interval = <100>;
>> + wps {
>> + label = "wps";
>> + gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
>> + linux,code = <KEY_WPS_BUTTON>;
>> + };
>> + dect {
>> + label = "dect";
>> + gpios = <&gpio 2 GPIO_ACTIVE_HIGH>;
>> + linux,code = <KEY_PHONE>;
>> + };
>> + };
>> +
>> + gpio-leds {
>> + compatible = "gpio-leds";
>> +
>> + power_green: power_green {
>> + label = "fritz7412:green:power";
>> + gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
>> + default-state = "keep";
>> + };
>> + power_red: power_red {
>> + label = "fritz7412:red:power";
>> + gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
>> + };
>> + fon {
>> + label = "fritz7412:green:fon";
>> + gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
>> + };
>> + dect {
>> + label = "fritz7412:green:dect";
>> + gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
>> + };
>> + wifi: wifi {
>> + label = "fritz7412:green:wifi";
>> + gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
>> + };
>> + info: info {
>> + label = "fritz7412:green:info";
>> + gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
>> + };
>> + };
>> +};
>> +
>> +&localbus {
>> + nand-parts at 0 {
>> + compatible = "lantiq,nand-xway";
>> + bank-width = <2>;
>> + reg = <1 0x0 0x2000000>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + lantiq,cs = <1>;
>> +
>> + partitions {
>> + compatible = "fixed-partitions";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> +
>> + partition at 0 {
>> + label = "urlader";
>> + reg = <0x0 0x40000>;
>> + read-only;
>> + };
>> +
>> + partition at 40000 {
>> + label = "nand-tffs";
>> + reg = <0x40000 0x400000>;
>> + read-only;
>> + };
>> +
>> + partition at 440000 {
>> + label = "kernel";
>> + reg = <0x440000 0x400000>;
>> + };
>> +
>> + partition at 840000 {
>> + label = "ubi";
>> + reg = <0x840000 0x3000000>;
>> + };
>> +
>> + partition at 3840000 {
>> + label = "reserved-kernel";
>> + reg = <0x3840000 0x400000>;
>> + read-only;
>> + };
>> +
>> + partition at 3c40000 {
>> + label = "reserved-filesystem";
>> + reg = <0x3c40000 0x3000000>;
>> + read-only;
>> + };
>> +
>> + partition at 6c40000 {
>> + label = "config";
>> + reg = <0x6c40000 0x400000>;
>> + read-only;
>> + };
>> +
>> + partition at 6e40000 {
>> + label = "nand-filesystem";
>> + reg = <0x6e40000 0x400000>;
>> + read-only;
>> + };
>> + };
>> + };
>> +};
>> +
>> +&pcie0 {
>> + status = "okay";
>> + gpio-reset = <&gpio 11 GPIO_ACTIVE_HIGH>;
>> +
>> + pcie at 0 {
>> + reg = <0 0 0 0 0>;
>> + #interrupt-cells = <1>;
>> + #size-cells = <2>;
>> + #address-cells = <3>;
>> + device_type = "pci";
>> +
>> + wifi at 168c,002e {
>> + compatible = "pci168c,002e";
>> + reg = <0 0 0 0 0>;
>> + qca,no-eeprom; /* load from
>> ath9k-eeprom-pci-0000:01:00.0.bin */
>> + };
>> + };
>> +};
>> +
>> +&gpio {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&state_default>;
>> +
>> + state_default: pinmux {
>> + mdio {
>> + lantiq,groups = "mdio";
>> + lantiq,function = "mdio";
>> + };
>> + pcie-rst {
>> + lantiq,pins = "io11";
>> + lantiq,open-drain = <1>;
>> + lantiq,output = <1>;
>> + };
>> + nand-mux {
>> + lantiq,groups = "nand cle", "nand ale",
>> + "nand rd", "nand cs1",
>> + "nand rdy";
>> + lantiq,function = "ebu";
>> + };
>> + nand-pins {
>> + lantiq,pins = "io13", "io24", "io49";
>> + lantiq,pull = <1>;
>> + };
>> +
>> + /*
>> + other gpios:
>> +
>> + dect reset: 33 output open drain
>> + dect rd: 8 active low push pull
>> +
>> + tdm fsc: 9 input + pull-up
>> + tdm/spi do: 16 output
>> + tdm/spi di: 17 input + pull-up
>> + tdm dcl/spi clk: 18 output active low
>> + tdm clk enable: 7 output active high
>> + tdm/spi cs: 10 output active low/high
>> + spi wp: 12 output active low
>> +
>> + boot sel2: 23 active high
>> + boot sel3: 38 active high
>> + boot sel4: 49 active high (also nand rd)
>> + */
>> + };
>> +};
>> +
>> +&gphy0 {
>> + lantiq,gphy-mode = <GPHY_MODE_FE>;
>> +};
>> +
>> +ð0 {
>> + lantiq,phys = <&gphy0>;
>> +
>> + interface at 0 {
>> + compatible = "lantiq,xrx200-pdi";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + reg = <0>;
>> + mac-address = [ 00 11 22 33 44 55 ];
>> + lantiq,switch;
>> +
>> + ethernet at 2 {
>> + compatible = "lantiq,xrx200-pdi-port";
>> + reg = <2>;
>> + phy-mode = "gmii";
>> + phy-handle = <&phy11>;
>> + };
>> + };
>> +
>> + mdio at 0 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "lantiq,xrx200-mdio";
>> + phy11: ethernet-phy at 11 {
>> + reg = <0x11>;
>> + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
>> + };
>> + };
>> +};
>> +
>> +&vmmc {
>> + status = "okay";
>> +};
>> diff --git
>> a/target/linux/lantiq/files-4.9/arch/mips/boot/dts/FRITZ7412.dts
>> b/target/linux/lantiq/files-4.9/arch/mips/boot/dts/FRITZ7412.dts
>> new file mode 100644
>> index 0000000000..23f80db121
>> --- /dev/null
>> +++ b/target/linux/lantiq/files-4.9/arch/mips/boot/dts/FRITZ7412.dts
>> @@ -0,0 +1,242 @@
>> +/dts-v1/;
>> +
>> +#include "vr9.dtsi"
>> +
>> +#include <dt-bindings/input/input.h>
>> +
>> +/ {
>> + compatible = "avm,fritz7412", "lantiq,xway", "lantiq,vr9";
>> + model = "1&1 DSL-Modem / 1&1 WLAN-Router";
>> +
>> + chosen {
>> + bootargs = "console=ttyLTQ0,115200 mem=126M
>> vpe1_load_addr=0x87e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp";
>> + };
>> +
>> + aliases {
>> + led-boot = &power_green;
>> + led-failsafe = &power_red;
>> + led-running = &power_green;
>> +
>> + led-dsl = &info;
>> + led-wifi = &wifi;
>> + };
>> +
>> + memory at 0 {
>> + reg = <0x0 0x8000000>;
>> + };
>> +
>> + fpi at 10000000 {
>> + localbus at 0 {
>> + nand-parts at 0 {
>> + compatible = "lantiq,nand-xway";
>> + bank-width = <2>;
>> + reg = <1 0x0 0x2000000>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + lantiq,cs = <1>;
>> +
>> + partitions {
>> + compatible = "fixed-partitions";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> +
>> + partition at 0 {
>> + label = "urlader";
>> + reg = <0x0 0x40000>;
>> + read-only;
>> + };
>> +
>> + partition at 40000 {
>> + label = "nand-tffs";
>> + reg = <0x40000 0x400000>;
>> + read-only;
>> + };
>> +
>> + partition at 440000 {
>> + label = "kernel";
>> + reg = <0x440000 0x400000>;
>> + };
>> +
>> + partition at 840000 {
>> + label = "ubi";
>> + reg = <0x840000 0x3000000>;
>> + };
>> +
>> + partition at 3840000 {
>> + label = "reserved-kernel";
>> + reg = <0x3840000 0x400000>;
>> + read-only;
>> + };
>> +
>> + partition at 3c40000 {
>> + label = "reserved-filesystem";
>> + reg = <0x3c40000 0x3000000>;
>> + read-only;
>> + };
>> +
>> + partition at 6c40000 {
>> + label = "config";
>> + reg = <0x6c40000 0x400000>;
>> + read-only;
>> + };
>> +
>> + partition at 6e40000 {
>> + label = "nand-filesystem";
>> + reg = <0x6e40000 0x400000>;
>> + read-only;
>> + };
>> + };
>> + };
>> + };
>> + };
>> +
>> + gphy-xrx200 {
>> + compatible = "lantiq,phy-xrx200";
>> + firmware = "lantiq/xrx200_phy11g_a22.bin";
>> + phys = [ 00 ];
>> + };
>> +
>> + gpio-keys-polled {
>> + compatible = "gpio-keys-polled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + poll-interval = <100>;
>> + wps {
>> + label = "wps";
>> + gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
>> + linux,code = <KEY_WPS_BUTTON>;
>> + };
>> + dect {
>> + label = "dect";
>> + gpios = <&gpio 2 GPIO_ACTIVE_HIGH>;
>> + linux,code = <KEY_PHONE>;
>> + };
>> + };
>> +
>> + gpio-leds {
>> + compatible = "gpio-leds";
>> +
>> + power_green: power_green {
>> + label = "fritz7412:green:power";
>> + gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
>> + default-state = "keep";
>> + };
>> + power_red: power_red {
>> + label = "fritz7412:red:power";
>> + gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
>> + };
>> + fon {
>> + label = "fritz7412:green:fon";
>> + gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
>> + };
>> + dect {
>> + label = "fritz7412:green:dect";
>> + gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
>> + };
>> + wifi: wifi {
>> + label = "fritz7412:green:wifi";
>> + gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
>> + };
>> + info: info {
>> + label = "fritz7412:green:info";
>> + gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
>> + };
>> + };
>> +};
>> +
>> +&pcie0 {
>> + status = "okay";
>> + gpio-reset = <&gpio 11 GPIO_ACTIVE_HIGH>;
>> +
>> + pcie at 0 {
>> + reg = <0 0 0 0 0>;
>> + #interrupt-cells = <1>;
>> + #size-cells = <2>;
>> + #address-cells = <3>;
>> + device_type = "pci";
>> +
>> + wifi at 168c,002e {
>> + compatible = "pci168c,002e";
>> + reg = <0 0 0 0 0>;
>> + qca,no-eeprom; /* load from
>> ath9k-eeprom-pci-0000:01:00.0.bin */
>> + };
>> + };
>> +};
>> +
>> +&gpio {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&state_default>;
>> +
>> + state_default: pinmux {
>> + mdio {
>> + lantiq,groups = "mdio";
>> + lantiq,function = "mdio";
>> + };
>> + pcie-rst {
>> + lantiq,pins = "io11";
>> + lantiq,open-drain = <1>;
>> + lantiq,output = <1>;
>> + };
>> + nand-mux {
>> + lantiq,groups = "nand cle", "nand ale",
>> + "nand rd", "nand cs1",
>> + "nand rdy";
>> + lantiq,function = "ebu";
>> + };
>> + nand-pins {
>> + lantiq,pins = "io13", "io24", "io49";
>> + lantiq,pull = <1>;
>> + };
>> +
>> + /*
>> + other gpios:
>> +
>> + dect reset: 33 output open drain
>> + dect rd: 8 active low push pull
>> +
>> + tdm fsc: 9 input + pull-up
>> + tdm/spi do: 16 output
>> + tdm/spi di: 17 input + pull-up
>> + tdm dcl/spi clk: 18 output active low
>> + tdm clk enable: 7 output active high
>> + tdm/spi cs: 10 output active low/high
>> + spi wp: 12 output active low
>> +
>> + boot sel2: 23 active high
>> + boot sel3: 38 active high
>> + boot sel4: 49 active high (also nand rd)
>> + */
>> + };
>> +};
>> +
>> +ð0 {
>> + interface at 0 {
>> + compatible = "lantiq,xrx200-pdi";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + reg = <0>;
>> + mac-address = [ 00 11 22 33 44 55 ];
>> + lantiq,switch;
>> +
>> + ethernet at 2 {
>> + compatible = "lantiq,xrx200-pdi-port";
>> + reg = <2>;
>> + phy-mode = "gmii";
>> + phy-handle = <&phy11>;
>> + };
>> + };
>> +
>> + mdio at 0 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "lantiq,xrx200-mdio";
>> + phy11: ethernet-phy at 11 {
>> + reg = <0x11>;
>> + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
>> + };
>> + };
>> +};
>> +
>> +&vmmc {
>> + status = "okay";
>> +};
>> diff --git
>> a/target/linux/lantiq/files-4.9/arch/mips/boot/dts/vr9.dtsi
>> b/target/linux/lantiq/files-4.9/arch/mips/boot/dts/vr9.dtsi
>> index dbcbb3dcec..f787ad7e4d 100644
>> --- a/target/linux/lantiq/files-4.9/arch/mips/boot/dts/vr9.dtsi
>> +++ b/target/linux/lantiq/files-4.9/arch/mips/boot/dts/vr9.dtsi
>> @@ -82,7 +82,7 @@
>> reg = <0x106a00 0x200>;
>> };
>> - vmmc at 107000 {
>> + vmmc: vmmc at 103000 {
>> status = "disabled";
>> compatible = "lantiq,vmmc-xway";
>> reg = <0x103000 0x400>;
>> diff --git a/target/linux/lantiq/image/Makefile
>> b/target/linux/lantiq/image/Makefile
>> index e52e43c6e5..6a3c8aef0f 100644
>> --- a/target/linux/lantiq/image/Makefile
>> +++ b/target/linux/lantiq/image/Makefile
>> @@ -103,6 +103,7 @@ define Device/AVM
>> KERNEL := kernel-bin | append-dtb | lzma | eva-image
>> IMAGE/sysupgrade.bin := append-kernel | pad-to 64k |
>> append-avm-fakeroot | \
>> append-rootfs | pad-rootfs | append-metadata | check-size
>> $$$$(IMAGE_SIZE)
>> + KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | eva-image
>> endef
>> ifeq ($(SUBTARGET),ase)
>> @@ -630,6 +631,18 @@ define Device/avm_fritz7360sl
>> endef
>> TARGET_DEVICES += avm_fritz7360sl
>> +define Device/avm_fritz7412
>> + $(Device/AVM)
>> + $(Device/NAND)
>> + BOARD_NAME := FRITZ7412
>> + DEVICE_DTS := FRITZ7412
>> + KERNEL_SIZE := 4096k
>> + IMAGE_SIZE := 49152k
>> + DEVICE_TITLE := 1&1 DSL-Modem / WLAN-Router - FRITZ7412
>> + DEVICE_PACKAGES := kmod-ath9k kmod-owl-loader wpad-mini
>> kmod-ltq-tapi kmod-ltq-vmmc fritz-tffs-nand fritz-caldata
>> +endef
>> +TARGET_DEVICES += avm_fritz7412
>> +
>> define Device/arcadyan_vg3503j
>> IMAGE_SIZE := 8000k
>> DEVICE_DTS := VG3503J
>
More information about the Lede-dev
mailing list