[LEDE-DEV] [PATCH 2/2] mvebu: new subtarget cortex A53
Tomasz Maciej Nowak
tomek_n at o2.pl
Wed Mar 7 13:10:02 PST 2018
This commit introduces new subtarget for Marvell EBU Armada Cortex A53
processor based devices.
The first device is Globalscale ESPRESSObin. Some hardware specs:
SoC: Marvell Armada 3700LP (88F3720) dual core ARM Cortex A53
processor up to 1.2GHz
RAM: 512MB, 1GB or 2GB DDR3
Storage: SATA interface
µSD card slot with footprint for an optional 4GB EMMC
4MB SPI NOR flash for bootloader
Ethernet: Topaz Networking Switch (88E6341) with 3x GbE ports
Connectors: USB 3.0
USB 2.0
µUSB port connected to PL2303SA (USB to serial bridge
controller) for UART access
Expansion: 2x 46-pin GPIO headers for accessories and shields with
I2C, GPIOs, PWM, UART, SPI, MMC, etc
MiniPCIe slot
Misc: Reset button, JTAG interface
Currently booting only from µSD card is supported.
The boards depending on date of dispatch can come with various U-Boot
versions. For the newest version 2017.03-armada-17.10 no manual
intervention should be needed to boot OpenWrt image. For the older ones
it's necessary to modify default U-Boot environment:
1. Interrupt boot process to run U-Boot command line,
2. Run following commands:
(for version 2017.03-armada-17.06 and 2017.03-armada-17.08)
setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000"
saveenv
(for version 2015.01-armada-17.02 and 2015.01-armada-17.04)
setenv bootargs "console=ttyMV0,115200 root=/dev/mmcblk0p2 rw rootwait"
setenv bootcmd "ext4load mmc 0:1 ${fdt_addr} armada-3720-espressobin.dtb; ext4load mmc 0:1 ${kernel_addr} Image; booti ${kernel_addr} - ${fdt_addr}"
saveenv
3. Poweroff, insert SD card with OpenWrt image, boot and enjoy.
Signed-off-by: Tomasz Maciej Nowak <tomek_n at o2.pl>
---
target/linux/mvebu/Makefile | 4 +-
.../linux/mvebu/base-files/etc/board.d/02_network | 3 +
target/linux/mvebu/base-files/lib/mvebu.sh | 3 +
.../linux/mvebu/base-files/lib/upgrade/platform.sh | 4 +-
target/linux/mvebu/config-4.14 | 1 +
target/linux/mvebu/cortexa53/config-default | 119 ++++++++
target/linux/mvebu/cortexa53/target.mk | 15 +
target/linux/mvebu/image/Makefile | 26 +-
target/linux/mvebu/image/cortex-a53.mk | 16 ++
.../mvebu/image/globalscale-espressobin.bootscript | 10 +
...mvebu-armada-37xx-periph-cosmetic-changes.patch | 78 +++++
...rmada-37xx-periph-prepare-cpu-clk-to-be-u.patch | 178 ++++++++++++
...rmada-37xx-periph-add-DVFS-support-for-cp.patch | 315 +++++++++++++++++++++
...-cpufreq-Add-DVFS-support-for-Armada-37xx.patch | 297 +++++++++++++++++++
...hange-SPI-mode-before-asserting-chip-sele.patch | 70 +++++
...dts-marvell-Fix-A37xx-UART0-register-size.patch | 39 +++
...64-dts-marvell-armada-37xx-add-UART-clock.patch | 27 ++
...arvell-armada-37xx-add-nodes-allowing-cpu.patch | 48 ++++
...m64-dts-marvell-armada37xx-Add-eth0-alias.patch | 20 ++
...521-esporessobin-dt-enable-spi-nor-on-i2c.patch | 29 ++
...in-PCI-configuration-read-write-functions.patch | 66 +++++
...IO_ADDR_LS-correctly-in-advk_pcie_rd_conf.patch | 53 ++++
...t-and-device-to-the-same-MAX-payload-size.patch | 137 +++++++++
...tead-of-isr0-interrupt-in-legacy-irq-mode.patch | 143 ++++++++++
...PCI-aardvark-disable-LOS-state-by-default.patch | 55 ++++
...rk-fix-PCIe-max-read-request-size-setting.patch | 63 +++++
26 files changed, 1813 insertions(+), 6 deletions(-)
create mode 100644 target/linux/mvebu/cortexa53/config-default
create mode 100644 target/linux/mvebu/cortexa53/target.mk
create mode 100644 target/linux/mvebu/image/cortex-a53.mk
create mode 100644 target/linux/mvebu/image/globalscale-espressobin.bootscript
create mode 100644 target/linux/mvebu/patches-4.14/500-clk-mvebu-armada-37xx-periph-cosmetic-changes.patch
create mode 100644 target/linux/mvebu/patches-4.14/501-clk-mvebu-armada-37xx-periph-prepare-cpu-clk-to-be-u.patch
create mode 100644 target/linux/mvebu/patches-4.14/502-clk-mvebu-armada-37xx-periph-add-DVFS-support-for-cp.patch
create mode 100644 target/linux/mvebu/patches-4.14/503-cpufreq-Add-DVFS-support-for-Armada-37xx.patch
create mode 100644 target/linux/mvebu/patches-4.14/504-spi-a3700-Change-SPI-mode-before-asserting-chip-sele.patch
create mode 100644 target/linux/mvebu/patches-4.14/505-arm64-dts-marvell-Fix-A37xx-UART0-register-size.patch
create mode 100644 target/linux/mvebu/patches-4.14/506-arm64-dts-marvell-armada-37xx-add-UART-clock.patch
create mode 100644 target/linux/mvebu/patches-4.14/507-arm64-dts-marvell-armada-37xx-add-nodes-allowing-cpu.patch
create mode 100644 target/linux/mvebu/patches-4.14/520-arm64-dts-marvell-armada37xx-Add-eth0-alias.patch
create mode 100644 target/linux/mvebu/patches-4.14/521-esporessobin-dt-enable-spi-nor-on-i2c.patch
create mode 100644 target/linux/mvebu/patches-4.14/522-PCI-aardvark-fix-logic-in-PCI-configuration-read-write-functions.patch
create mode 100644 target/linux/mvebu/patches-4.14/523-PCI-aardvark-set-PIO_ADDR_LS-correctly-in-advk_pcie_rd_conf.patch
create mode 100644 target/linux/mvebu/patches-4.14/524-PCI-aardvark-set-host-and-device-to-the-same-MAX-payload-size.patch
create mode 100644 target/linux/mvebu/patches-4.14/525-PCI-aardvark-use-isr1-instead-of-isr0-interrupt-in-legacy-irq-mode.patch
create mode 100644 target/linux/mvebu/patches-4.14/526-PCI-aardvark-disable-LOS-state-by-default.patch
create mode 100644 target/linux/mvebu/patches-4.14/527-PCI-aardvark-fix-PCIe-max-read-request-size-setting.patch
diff --git a/target/linux/mvebu/Makefile b/target/linux/mvebu/Makefile
index 490583fb39..75fdc8e853 100644
--- a/target/linux/mvebu/Makefile
+++ b/target/linux/mvebu/Makefile
@@ -7,9 +7,9 @@
include $(TOPDIR)/rules.mk
BOARD:=mvebu
-BOARDNAME:=Marvell Armada 37x/38x/XP
+BOARDNAME:=Marvell EBU Armada
FEATURES:=fpu usb pci pcie gpio nand squashfs
-SUBTARGETS:=cortexa9
+SUBTARGETS:=cortexa9 cortexa53
MAINTAINER:=Imre Kaloz <kaloz at openwrt.org>
KERNEL_PATCHVER:=4.14
diff --git a/target/linux/mvebu/base-files/etc/board.d/02_network b/target/linux/mvebu/base-files/etc/board.d/02_network
index 4fc95406ca..32ca3e22d5 100755
--- a/target/linux/mvebu/base-files/etc/board.d/02_network
+++ b/target/linux/mvebu/base-files/etc/board.d/02_network
@@ -38,6 +38,9 @@ armada-388-clearfog-*)
armada-xp-gp)
ucidef_set_interface_lan "eth0 eth1 eth2 eth3"
;;
+globalscale,espressobin)
+ ucidef_set_interfaces_lan_wan "lan0 lan1" "wan"
+ ;;
*)
ucidef_set_interface_lan "eth0"
;;
diff --git a/target/linux/mvebu/base-files/lib/mvebu.sh b/target/linux/mvebu/base-files/lib/mvebu.sh
index fb3ddee4f5..5c4f68a7a9 100755
--- a/target/linux/mvebu/base-files/lib/mvebu.sh
+++ b/target/linux/mvebu/base-files/lib/mvebu.sh
@@ -17,6 +17,9 @@ mvebu_board_detect() {
*"Marvell Armada 370 Evaluation Board")
name="armada-370-db"
;;
+ *"Globalscale Marvell ESPRESSOBin Board")
+ name="globalscale,espressobin"
+ ;;
*"Globalscale Mirabox")
name="mirabox"
;;
diff --git a/target/linux/mvebu/base-files/lib/upgrade/platform.sh b/target/linux/mvebu/base-files/lib/upgrade/platform.sh
index b59c765a38..413069c7a4 100755
--- a/target/linux/mvebu/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mvebu/base-files/lib/upgrade/platform.sh
@@ -16,7 +16,7 @@ platform_do_upgrade() {
armada-385-linksys-caiman|armada-385-linksys-cobra|armada-385-linksys-rango|armada-385-linksys-shelby|armada-xp-linksys-mamba)
platform_do_upgrade_linksys "$ARGV"
;;
- armada-388-clearfog-base|armada-388-clearfog-pro)
+ armada-388-clearfog-base|armada-388-clearfog-pro|globalscale,espressobin)
platform_do_upgrade_sdcard "$ARGV"
;;
*)
@@ -29,7 +29,7 @@ platform_copy_config() {
armada-385-linksys-caiman|armada-385-linksys-cobra|armada-385-linksys-rango|armada-385-linksys-shelby|armada-xp-linksys-mamba)
platform_copy_config_linksys
;;
- armada-388-clearfog-base|armada-388-clearfog-pro)
+ armada-388-clearfog-base|armada-388-clearfog-pro|globalscale,espressobin)
platform_copy_config_sdcard "$ARGV"
;;
esac
diff --git a/target/linux/mvebu/config-4.14 b/target/linux/mvebu/config-4.14
index 71123f52bc..c0dd113963 100644
--- a/target/linux/mvebu/config-4.14
+++ b/target/linux/mvebu/config-4.14
@@ -39,6 +39,7 @@ CONFIG_ARMADA_38X_CLK=y
CONFIG_ARMADA_THERMAL=y
CONFIG_ARMADA_XP_CLK=y
CONFIG_ARM_APPENDED_DTB=y
+# CONFIG_ARM_ARMADA_37XX_CPUFREQ is not set
CONFIG_ARM_ATAG_DTB_COMPAT=y
# CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND is not set
CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER=y
diff --git a/target/linux/mvebu/cortexa53/config-default b/target/linux/mvebu/cortexa53/config-default
new file mode 100644
index 0000000000..886bd65f77
--- /dev/null
+++ b/target/linux/mvebu/cortexa53/config-default
@@ -0,0 +1,119 @@
+CONFIG_64BIT=y
+# CONFIG_ACPI is not set
+CONFIG_ARCH_DMA_ADDR_T_64BIT=y
+CONFIG_ARCH_HAS_CACHE_LINE_SIZE=y
+CONFIG_ARCH_HAS_FORTIFY_SOURCE=y
+CONFIG_ARCH_HAS_HOLES_MEMORYMODEL=y
+CONFIG_ARCH_HAS_KCOV=y
+CONFIG_ARCH_MMAP_RND_BITS=18
+CONFIG_ARCH_MMAP_RND_BITS_MAX=24
+CONFIG_ARCH_MMAP_RND_BITS_MIN=18
+CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MIN=11
+# CONFIG_ARCH_OPTIONAL_KERNEL_RWX is not set
+# CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT is not set
+CONFIG_ARCH_PHYS_ADDR_T_64BIT=y
+CONFIG_ARCH_PROC_KCORE_TEXT=y
+CONFIG_ARCH_SELECT_MEMORY_MODEL=y
+CONFIG_ARCH_SPARSEMEM_DEFAULT=y
+CONFIG_ARCH_SPARSEMEM_ENABLE=y
+CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
+CONFIG_ARCH_SUPPORTS_MEMORY_FAILURE=y
+CONFIG_ARCH_SUPPORTS_NUMA_BALANCING=y
+CONFIG_ARCH_WANT_COMPAT_IPC_PARSE_VERSION=y
+CONFIG_ARCH_WANT_FRAME_POINTERS=y
+CONFIG_ARCH_WANT_HUGE_PMD_SHARE=y
+CONFIG_ARM64=y
+# CONFIG_ARM64_16K_PAGES is not set
+CONFIG_ARM64_4K_PAGES=y
+# CONFIG_ARM64_64K_PAGES is not set
+CONFIG_ARM64_CONT_SHIFT=4
+# CONFIG_ARM64_CRYPTO is not set
+# CONFIG_ARM64_HW_AFDBM is not set
+# CONFIG_ARM64_LSE_ATOMICS is not set
+CONFIG_ARM64_PAGE_SHIFT=12
+# CONFIG_ARM64_PAN is not set
+# CONFIG_ARM64_PMEM is not set
+# CONFIG_ARM64_PTDUMP_CORE is not set
+# CONFIG_ARM64_PTDUMP_DEBUGFS is not set
+# CONFIG_ARM64_RANDOMIZE_TEXT_OFFSET is not set
+# CONFIG_ARM64_SW_TTBR0_PAN is not set
+# CONFIG_ARM64_UAO is not set
+CONFIG_ARM64_VA_BITS=39
+CONFIG_ARM64_VA_BITS_39=y
+# CONFIG_ARM64_VA_BITS_48 is not set
+# CONFIG_ARM64_VHE is not set
+CONFIG_ARMADA_37XX_CLK=y
+CONFIG_ARMADA_AP806_SYSCON=y
+CONFIG_ARMADA_CP110_SYSCON=y
+CONFIG_ARM_AMBA=y
+CONFIG_ARM_ARCH_TIMER=y
+CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
+CONFIG_ARM_ARMADA_37XX_CPUFREQ=y
+CONFIG_ARM_GIC_V2M=y
+CONFIG_ARM_GIC_V3=y
+CONFIG_ARM_GIC_V3_ITS=y
+# CONFIG_ARM_PL172_MPMC is not set
+CONFIG_ARM_PSCI_FW=y
+# CONFIG_ARM_SP805_WATCHDOG is not set
+CONFIG_AUDIT_ARCH_COMPAT_GENERIC=y
+# CONFIG_COMPAT is not set
+# CONFIG_DEBUG_ALIGN_RODATA is not set
+CONFIG_FRAME_POINTER=y
+CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y
+CONFIG_GENERIC_CSUM=y
+CONFIG_GENERIC_IRQ_MIGRATION=y
+CONFIG_GENERIC_PINCONF=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GPIOLIB_IRQCHIP=y
+CONFIG_HAVE_ALIGNED_STRUCT_PAGE=y
+CONFIG_HAVE_ARCH_HUGE_VMAP=y
+CONFIG_HAVE_ARCH_KASAN=y
+CONFIG_HAVE_ARCH_TRANSPARENT_HUGEPAGE=y
+CONFIG_HAVE_ARCH_VMAP_STACK=y
+CONFIG_HAVE_CMPXCHG_DOUBLE=y
+CONFIG_HAVE_CMPXCHG_LOCAL=y
+CONFIG_HAVE_DEBUG_BUGVERBOSE=y
+CONFIG_HAVE_GENERIC_GUP=y
+CONFIG_HAVE_MEMORY_PRESENT=y
+CONFIG_HAVE_PATA_PLATFORM=y
+CONFIG_HAVE_RCU_TABLE_FREE=y
+# CONFIG_HUGETLBFS is not set
+CONFIG_ILLEGAL_POINTER_VALUE=0xdead000000000000
+CONFIG_MFD_SYSCON=y
+CONFIG_MMC_SDHCI_XENON=y
+CONFIG_MODULES_USE_ELF_RELA=y
+CONFIG_MVEBU_GICP=y
+CONFIG_MVEBU_ICU=y
+CONFIG_MVEBU_ODMI=y
+CONFIG_MVEBU_PIC=y
+CONFIG_NEED_SG_DMA_LENGTH=y
+CONFIG_NET_DSA=y
+CONFIG_NET_DSA_MV88E6XXX=y
+CONFIG_NET_DSA_MV88E6XXX_GLOBAL2=y
+CONFIG_NET_DSA_TAG_DSA=y
+CONFIG_NET_DSA_TAG_EDSA=y
+CONFIG_NET_SWITCHDEV=y
+# CONFIG_NUMA is not set
+CONFIG_PARTITION_PERCPU=y
+CONFIG_PCI_AARDVARK=y
+CONFIG_PCI_BUS_ADDR_T_64BIT=y
+CONFIG_PGTABLE_LEVELS=3
+CONFIG_PHYS_ADDR_T_64BIT=y
+CONFIG_PINCTRL_ARMADA_37XX=y
+CONFIG_PINCTRL_ARMADA_AP806=y
+CONFIG_PINCTRL_ARMADA_CP110=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_SUPPLY=y
+# CONFIG_RANDOMIZE_BASE is not set
+CONFIG_REGULATOR_GPIO=y
+# CONFIG_SERIAL_AMBA_PL011 is not set
+CONFIG_SPARSEMEM=y
+CONFIG_SPARSEMEM_EXTREME=y
+CONFIG_SPARSEMEM_MANUAL=y
+CONFIG_SPARSEMEM_VMEMMAP=y
+CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y
+CONFIG_SPI_ARMADA_3700=y
+CONFIG_SYSCTL_EXCEPTION_TRACE=y
+CONFIG_SYS_SUPPORTS_HUGETLBFS=y
+CONFIG_THREAD_INFO_IN_TASK=y
+CONFIG_VMAP_STACK=y
diff --git a/target/linux/mvebu/cortexa53/target.mk b/target/linux/mvebu/cortexa53/target.mk
new file mode 100644
index 0000000000..acc18d3454
--- /dev/null
+++ b/target/linux/mvebu/cortexa53/target.mk
@@ -0,0 +1,15 @@
+#
+# Copyright (C) 2017 Hauke Mehrtens
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+include $(TOPDIR)/rules.mk
+
+ARCH:=aarch64
+BOARDNAME:=Marvell Armada 3700LP (ARM64)
+CPU_TYPE:=cortex-a53
+FEATURES+=ext4
+
+KERNELNAME:=Image dtbs
diff --git a/target/linux/mvebu/image/Makefile b/target/linux/mvebu/image/Makefile
index 1ed9c39f00..23ad2a95ce 100644
--- a/target/linux/mvebu/image/Makefile
+++ b/target/linux/mvebu/image/Makefile
@@ -27,17 +27,28 @@ endef
define Build/boot-scr
rm -f $@-boot.scr
- mkimage -A arm -O linux -T script -C none -a 0 -e 0 -d $(DEVICE_NAME).bootscript $@-boot.scr
+ sed -e 's#@ROOT@#$(SIGNATURE)#g' \
+ $(DEVICE_NAME).bootscript > $@-new.bootscript
+ mkimage -A arm -O linux -T script -C none -a 0 -e 0 -d $@-new.bootscript $@-boot.scr
endef
define Build/boot-img
rm -f $@.boot
mkfs.fat -C $@.boot 16384
$(foreach dts,$(DEVICE_DTS), mcopy -i $@.boot $(DTS_DIR)/$(dts).dtb ::$(dts).dtb;)
- mcopy -i $@.boot $(IMAGE_KERNEL) ::zImage
+ mcopy -i $@.boot $(IMAGE_KERNEL) ::$(KERNEL_NAME)
-mcopy -i $@.boot $@-boot.scr ::boot.scr
endef
+define Build/boot-img-ext4
+ rm -fR $@.boot
+ mkdir -p $@.boot
+ $(foreach dts,$(DEVICE_DTS), $(CP) $(DTS_DIR)/$(dts).dtb $@.boot;)
+ $(CP) $(IMAGE_KERNEL) $@.boot/$(KERNEL_NAME)
+ -$(CP) $@-boot.scr $@.boot/boot.scr
+ make_ext4fs -J -l 16384K $@.bootimg $@.boot
+endef
+
define Build/sdcard-img
if [ -n "$(UBOOT)" ]; then UBOOT="$(STAGING_DIR_IMAGE)/$(UBOOT)"; fi; \
ROOTFS_SIZE=$$(( $(CONFIG_TARGET_ROOTFS_PARTSIZE) * 1024 * 2 )); \
@@ -48,6 +59,16 @@ define Build/sdcard-img
83 $$ROOTFS_SIZE $(IMAGE_ROOTFS)
endef
+define Build/sdcard-img-ext4
+ if [ -n "$(UBOOT)" ]; then UBOOT="$(STAGING_DIR_IMAGE)/$(UBOOT)"; fi; \
+ ROOTFS_SIZE=$$(( $(CONFIG_TARGET_ROOTFS_PARTSIZE) * 1024 * 2 )); \
+ SIGNATURE="$(SIGNATURE)" \
+ ./gen_mvebu_sdcard_img.sh $@ \
+ $$UBOOT \
+ 83 32768 $@.bootimg \
+ 83 $$ROOTFS_SIZE $(IMAGE_ROOTFS)
+endef
+
define Device/Default
PROFILES := Default
DEVICE_DTS := $(1)
@@ -90,5 +111,6 @@ define Device/NAND-512K
endef
include cortex-a9.mk
+include cortex-a53.mk
$(eval $(call BuildImage))
diff --git a/target/linux/mvebu/image/cortex-a53.mk b/target/linux/mvebu/image/cortex-a53.mk
new file mode 100644
index 0000000000..711d2c0be8
--- /dev/null
+++ b/target/linux/mvebu/image/cortex-a53.mk
@@ -0,0 +1,16 @@
+ifeq ($(SUBTARGET),cortexa53)
+
+define Device/globalscale-espressobin
+ KERNEL_NAME := Image
+ KERNEL := kernel-bin
+ DEVICE_TITLE := ESPRESSObin (Marvell Armada 3700 Community Board)
+ DEVICE_PACKAGES := e2fsprogs ethtool mkf2fs kmod-fs-vfat kmod-usb2 kmod-usb3 kmod-usb-storage
+ IMAGES := sdcard.img.gz
+ IMAGE/sdcard.img.gz := boot-scr | boot-img-ext4 | sdcard-img-ext4 | gzip | append-metadata
+ DEVICE_DTS := armada-3720-espressobin
+ DTS_DIR := $(DTS_DIR)/marvell
+ SUPPORTED_DEVICES := globalscale,espressobin
+endef
+TARGET_DEVICES += globalscale-espressobin
+
+endif
diff --git a/target/linux/mvebu/image/globalscale-espressobin.bootscript b/target/linux/mvebu/image/globalscale-espressobin.bootscript
new file mode 100644
index 0000000000..0d03ac8513
--- /dev/null
+++ b/target/linux/mvebu/image/globalscale-espressobin.bootscript
@@ -0,0 +1,10 @@
+setenv bootargs "root=PARTUUID=@ROOT at -02 rw rootwait"
+
+if test -n "${console}"; then
+ setenv bootargs "${bootargs} ${console}"
+fi
+
+load mmc 0:1 ${fdt_addr} armada-3720-espressobin.dtb
+load mmc 0:1 ${kernel_addr} Image
+
+booti ${kernel_addr} - ${fdt_addr}
diff --git a/target/linux/mvebu/patches-4.14/500-clk-mvebu-armada-37xx-periph-cosmetic-changes.patch b/target/linux/mvebu/patches-4.14/500-clk-mvebu-armada-37xx-periph-cosmetic-changes.patch
new file mode 100644
index 0000000000..7343e01d19
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/500-clk-mvebu-armada-37xx-periph-cosmetic-changes.patch
@@ -0,0 +1,78 @@
+From adf4e289dd7f801c3fe12e0e6b491e11e548cd3d Mon Sep 17 00:00:00 2001
+From: Gregory CLEMENT <gregory.clement at free-electrons.com>
+Date: Thu, 30 Nov 2017 14:40:27 +0100
+Subject: clk: mvebu: armada-37xx-periph: cosmetic changes
+
+This patches fixes few cosmetic issues such as alignment, blank lines
+and required space.
+
+Signed-off-by: Gregory CLEMENT <gregory.clement at free-electrons.com>
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+---
+ drivers/clk/mvebu/armada-37xx-periph.c | 17 +++++++++--------
+ 1 file changed, 9 insertions(+), 8 deletions(-)
+
+--- a/drivers/clk/mvebu/armada-37xx-periph.c
++++ b/drivers/clk/mvebu/armada-37xx-periph.c
+@@ -79,6 +79,7 @@ static const struct clk_div_table clk_ta
+ { .val = 1, .div = 4, },
+ { .val = 0, .div = 0, }, /* last entry */
+ };
++
+ static const struct clk_ops clk_double_div_ops;
+
+ #define PERIPH_GATE(_name, _bit) \
+@@ -217,7 +218,7 @@ PERIPH_CLK_FULL(counter, 23, 20, DIV_SEL
+ PERIPH_CLK_FULL_DD(eip97, 24, 24, DIV_SEL2, DIV_SEL2, 22, 19);
+ PERIPH_CLK_MUX_DIV(cpu, 22, DIV_SEL0, 28, clk_table6);
+
+-static struct clk_periph_data data_nb[] ={
++static struct clk_periph_data data_nb[] = {
+ REF_CLK_FULL_DD(mmc),
+ REF_CLK_FULL_DD(sata_host),
+ REF_CLK_FULL_DD(sec_at),
+@@ -281,7 +282,7 @@ static unsigned int get_div(void __iomem
+ }
+
+ static unsigned long clk_double_div_recalc_rate(struct clk_hw *hw,
+- unsigned long parent_rate)
++ unsigned long parent_rate)
+ {
+ struct clk_double_div *double_div = to_clk_double_div(hw);
+ unsigned int div;
+@@ -303,6 +304,7 @@ static const struct of_device_id armada_
+ .data = data_sb, },
+ { }
+ };
++
+ static int armada_3700_add_composite_clk(const struct clk_periph_data *data,
+ void __iomem *reg, spinlock_t *lock,
+ struct device *dev, struct clk_hw **hw)
+@@ -355,9 +357,9 @@ static int armada_3700_add_composite_clk
+ }
+
+ *hw = clk_hw_register_composite(dev, data->name, data->parent_names,
+- data->num_parents, mux_hw,
+- mux_ops, rate_hw, rate_ops,
+- gate_hw, gate_ops, CLK_IGNORE_UNUSED);
++ data->num_parents, mux_hw,
++ mux_ops, rate_hw, rate_ops,
++ gate_hw, gate_ops, CLK_IGNORE_UNUSED);
+
+ if (IS_ERR(*hw))
+ return PTR_ERR(*hw);
+@@ -406,12 +408,11 @@ static int armada_3700_periph_clock_prob
+ if (armada_3700_add_composite_clk(&data[i], reg,
+ &driver_data->lock, dev, hw))
+ dev_err(dev, "Can't register periph clock %s\n",
+- data[i].name);
+-
++ data[i].name);
+ }
+
+ ret = of_clk_add_hw_provider(np, of_clk_hw_onecell_get,
+- driver_data->hw_data);
++ driver_data->hw_data);
+ if (ret) {
+ for (i = 0; i < num_periph; i++)
+ clk_hw_unregister(driver_data->hw_data->hws[i]);
diff --git a/target/linux/mvebu/patches-4.14/501-clk-mvebu-armada-37xx-periph-prepare-cpu-clk-to-be-u.patch b/target/linux/mvebu/patches-4.14/501-clk-mvebu-armada-37xx-periph-prepare-cpu-clk-to-be-u.patch
new file mode 100644
index 0000000000..f9dec9f2ee
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/501-clk-mvebu-armada-37xx-periph-prepare-cpu-clk-to-be-u.patch
@@ -0,0 +1,178 @@
+From 9818a7a4fd10f72537cdf2a5ec3402f2c245ea24 Mon Sep 17 00:00:00 2001
+From: Gregory CLEMENT <gregory.clement at free-electrons.com>
+Date: Thu, 30 Nov 2017 14:40:28 +0100
+Subject: clk: mvebu: armada-37xx-periph: prepare cpu clk to be
+ used with DVFS
+
+When DVFS will be enabled then the cpu clk will use a different set of
+register at run time. That means that we won't be able to use the common
+callback and need to use our own ones.
+
+This patch prepares this change by switching on our own set of callbacks
+without modifying the behavior of the clocks.
+
+Signed-off-by: Gregory CLEMENT <gregory.clement at free-electrons.com>
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+---
+ drivers/clk/mvebu/armada-37xx-periph.c | 82 ++++++++++++++++++++++++++++++----
+ 1 file changed, 73 insertions(+), 9 deletions(-)
+
+--- a/drivers/clk/mvebu/armada-37xx-periph.c
++++ b/drivers/clk/mvebu/armada-37xx-periph.c
+@@ -46,7 +46,17 @@ struct clk_double_div {
+ u8 shift2;
+ };
+
++struct clk_pm_cpu {
++ struct clk_hw hw;
++ void __iomem *reg_mux;
++ u8 shift_mux;
++ u32 mask_mux;
++ void __iomem *reg_div;
++ u8 shift_div;
++};
++
+ #define to_clk_double_div(_hw) container_of(_hw, struct clk_double_div, hw)
++#define to_clk_pm_cpu(_hw) container_of(_hw, struct clk_pm_cpu, hw)
+
+ struct clk_periph_data {
+ const char *name;
+@@ -55,6 +65,7 @@ struct clk_periph_data {
+ struct clk_hw *mux_hw;
+ struct clk_hw *rate_hw;
+ struct clk_hw *gate_hw;
++ struct clk_hw *muxrate_hw;
+ bool is_double_div;
+ };
+
+@@ -81,6 +92,7 @@ static const struct clk_div_table clk_ta
+ };
+
+ static const struct clk_ops clk_double_div_ops;
++static const struct clk_ops clk_pm_cpu_ops;
+
+ #define PERIPH_GATE(_name, _bit) \
+ struct clk_gate gate_##_name = { \
+@@ -122,6 +134,18 @@ struct clk_divider rate_##_name = { \
+ } \
+ };
+
++#define PERIPH_PM_CPU(_name, _shift1, _reg, _shift2) \
++struct clk_pm_cpu muxrate_##_name = { \
++ .reg_mux = (void *)TBG_SEL, \
++ .mask_mux = 3, \
++ .shift_mux = _shift1, \
++ .reg_div = (void *)_reg, \
++ .shift_div = _shift2, \
++ .hw.init = &(struct clk_init_data){ \
++ .ops = &clk_pm_cpu_ops, \
++ } \
++};
++
+ #define PERIPH_CLK_FULL_DD(_name, _bit, _shift, _reg1, _reg2, _shift1, _shift2)\
+ static PERIPH_GATE(_name, _bit); \
+ static PERIPH_MUX(_name, _shift); \
+@@ -136,10 +160,6 @@ static PERIPH_DIV(_name, _reg, _shift1,
+ static PERIPH_GATE(_name, _bit); \
+ static PERIPH_DIV(_name, _reg, _shift, _table);
+
+-#define PERIPH_CLK_MUX_DIV(_name, _shift, _reg, _shift_div, _table) \
+-static PERIPH_MUX(_name, _shift); \
+-static PERIPH_DIV(_name, _reg, _shift_div, _table);
+-
+ #define PERIPH_CLK_MUX_DD(_name, _shift, _reg1, _reg2, _shift1, _shift2)\
+ static PERIPH_MUX(_name, _shift); \
+ static PERIPH_DOUBLEDIV(_name, _reg1, _reg2, _shift1, _shift2);
+@@ -180,13 +200,12 @@ static PERIPH_DOUBLEDIV(_name, _reg1, _r
+ .rate_hw = &rate_##_name.hw, \
+ }
+
+-#define REF_CLK_MUX_DIV(_name) \
++#define REF_CLK_PM_CPU(_name) \
+ { .name = #_name, \
+ .parent_names = (const char *[]){ "TBG-A-P", \
+ "TBG-B-P", "TBG-A-S", "TBG-B-S"}, \
+ .num_parents = 4, \
+- .mux_hw = &mux_##_name.hw, \
+- .rate_hw = &rate_##_name.hw, \
++ .muxrate_hw = &muxrate_##_name.hw, \
+ }
+
+ #define REF_CLK_MUX_DD(_name) \
+@@ -216,7 +235,7 @@ PERIPH_CLK_FULL_DD(ddr_fclk, 21, 16, DIV
+ PERIPH_CLK_FULL(trace, 22, 18, DIV_SEL0, 20, clk_table6);
+ PERIPH_CLK_FULL(counter, 23, 20, DIV_SEL0, 23, clk_table6);
+ PERIPH_CLK_FULL_DD(eip97, 24, 24, DIV_SEL2, DIV_SEL2, 22, 19);
+-PERIPH_CLK_MUX_DIV(cpu, 22, DIV_SEL0, 28, clk_table6);
++static PERIPH_PM_CPU(cpu, 22, DIV_SEL0, 28);
+
+ static struct clk_periph_data data_nb[] = {
+ REF_CLK_FULL_DD(mmc),
+@@ -235,7 +254,7 @@ static struct clk_periph_data data_nb[]
+ REF_CLK_FULL(trace),
+ REF_CLK_FULL(counter),
+ REF_CLK_FULL_DD(eip97),
+- REF_CLK_MUX_DIV(cpu),
++ REF_CLK_PM_CPU(cpu),
+ { },
+ };
+
+@@ -297,6 +316,37 @@ static const struct clk_ops clk_double_d
+ .recalc_rate = clk_double_div_recalc_rate,
+ };
+
++static u8 clk_pm_cpu_get_parent(struct clk_hw *hw)
++{
++ struct clk_pm_cpu *pm_cpu = to_clk_pm_cpu(hw);
++ int num_parents = clk_hw_get_num_parents(hw);
++ u32 val;
++
++ val = readl(pm_cpu->reg_mux) >> pm_cpu->shift_mux;
++ val &= pm_cpu->mask_mux;
++
++ if (val >= num_parents)
++ return -EINVAL;
++
++ return val;
++}
++
++static unsigned long clk_pm_cpu_recalc_rate(struct clk_hw *hw,
++ unsigned long parent_rate)
++{
++ struct clk_pm_cpu *pm_cpu = to_clk_pm_cpu(hw);
++ unsigned int div;
++
++ div = get_div(pm_cpu->reg_div, pm_cpu->shift_div);
++
++ return DIV_ROUND_UP_ULL((u64)parent_rate, div);
++}
++
++static const struct clk_ops clk_pm_cpu_ops = {
++ .get_parent = clk_pm_cpu_get_parent,
++ .recalc_rate = clk_pm_cpu_recalc_rate,
++};
++
+ static const struct of_device_id armada_3700_periph_clock_of_match[] = {
+ { .compatible = "marvell,armada-3700-periph-clock-nb",
+ .data = data_nb, },
+@@ -356,6 +406,20 @@ static int armada_3700_add_composite_clk
+ }
+ }
+
++ if (data->muxrate_hw) {
++ struct clk_pm_cpu *pmcpu_clk;
++ struct clk_hw *muxrate_hw = data->muxrate_hw;
++
++ pmcpu_clk = to_clk_pm_cpu(muxrate_hw);
++ pmcpu_clk->reg_mux = reg + (u64)pmcpu_clk->reg_mux;
++ pmcpu_clk->reg_div = reg + (u64)pmcpu_clk->reg_div;
++
++ mux_hw = muxrate_hw;
++ rate_hw = muxrate_hw;
++ mux_ops = muxrate_hw->init->ops;
++ rate_ops = muxrate_hw->init->ops;
++ }
++
+ *hw = clk_hw_register_composite(dev, data->name, data->parent_names,
+ data->num_parents, mux_hw,
+ mux_ops, rate_hw, rate_ops,
diff --git a/target/linux/mvebu/patches-4.14/502-clk-mvebu-armada-37xx-periph-add-DVFS-support-for-cp.patch b/target/linux/mvebu/patches-4.14/502-clk-mvebu-armada-37xx-periph-add-DVFS-support-for-cp.patch
new file mode 100644
index 0000000000..2065e788af
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/502-clk-mvebu-armada-37xx-periph-add-DVFS-support-for-cp.patch
@@ -0,0 +1,315 @@
+From 2089dc33ea0e3917465929d4020fbff3d6dbf7f4 Mon Sep 17 00:00:00 2001
+From: Gregory CLEMENT <gregory.clement at free-electrons.com>
+Date: Thu, 30 Nov 2017 14:40:29 +0100
+Subject: clk: mvebu: armada-37xx-periph: add DVFS support for cpu clocks
+
+When DVFS is enabled the CPU clock setting is done using an other set of
+registers.
+
+These Power Management registers are exposed through a syscon as they
+will also be used by other drivers such as the cpufreq.
+
+This patch add the possibility to modify the CPU frequency using the
+associate load level matching the target frequency. Then all the
+frequency switch is handle by the hardware.
+
+Signed-off-by: Gregory CLEMENT <gregory.clement at free-electrons.com>
+[sboyd at codeaurora.org: Grow a local variable for regmap pointer
+to keep lines shorter]
+Signed-off-by: Stephen Boyd <sboyd at codeaurora.org>
+---
+ drivers/clk/mvebu/armada-37xx-periph.c | 221 ++++++++++++++++++++++++++++++++-
+ 1 file changed, 217 insertions(+), 4 deletions(-)
+
+--- a/drivers/clk/mvebu/armada-37xx-periph.c
++++ b/drivers/clk/mvebu/armada-37xx-periph.c
+@@ -21,9 +21,11 @@
+ */
+
+ #include <linux/clk-provider.h>
++#include <linux/mfd/syscon.h>
+ #include <linux/of.h>
+ #include <linux/of_device.h>
+ #include <linux/platform_device.h>
++#include <linux/regmap.h>
+ #include <linux/slab.h>
+
+ #define TBG_SEL 0x0
+@@ -33,6 +35,26 @@
+ #define CLK_SEL 0x10
+ #define CLK_DIS 0x14
+
++#define LOAD_LEVEL_NR 4
++
++#define ARMADA_37XX_NB_L0L1 0x18
++#define ARMADA_37XX_NB_L2L3 0x1C
++#define ARMADA_37XX_NB_TBG_DIV_OFF 13
++#define ARMADA_37XX_NB_TBG_DIV_MASK 0x7
++#define ARMADA_37XX_NB_CLK_SEL_OFF 11
++#define ARMADA_37XX_NB_CLK_SEL_MASK 0x1
++#define ARMADA_37XX_NB_TBG_SEL_OFF 9
++#define ARMADA_37XX_NB_TBG_SEL_MASK 0x3
++#define ARMADA_37XX_NB_CONFIG_SHIFT 16
++#define ARMADA_37XX_NB_DYN_MOD 0x24
++#define ARMADA_37XX_NB_DFS_EN 31
++#define ARMADA_37XX_NB_CPU_LOAD 0x30
++#define ARMADA_37XX_NB_CPU_LOAD_MASK 0x3
++#define ARMADA_37XX_DVFS_LOAD_0 0
++#define ARMADA_37XX_DVFS_LOAD_1 1
++#define ARMADA_37XX_DVFS_LOAD_2 2
++#define ARMADA_37XX_DVFS_LOAD_3 3
++
+ struct clk_periph_driver_data {
+ struct clk_hw_onecell_data *hw_data;
+ spinlock_t lock;
+@@ -53,6 +75,7 @@ struct clk_pm_cpu {
+ u32 mask_mux;
+ void __iomem *reg_div;
+ u8 shift_div;
++ struct regmap *nb_pm_base;
+ };
+
+ #define to_clk_double_div(_hw) container_of(_hw, struct clk_double_div, hw)
+@@ -316,14 +339,94 @@ static const struct clk_ops clk_double_d
+ .recalc_rate = clk_double_div_recalc_rate,
+ };
+
++static void armada_3700_pm_dvfs_update_regs(unsigned int load_level,
++ unsigned int *reg,
++ unsigned int *offset)
++{
++ if (load_level <= ARMADA_37XX_DVFS_LOAD_1)
++ *reg = ARMADA_37XX_NB_L0L1;
++ else
++ *reg = ARMADA_37XX_NB_L2L3;
++
++ if (load_level == ARMADA_37XX_DVFS_LOAD_0 ||
++ load_level == ARMADA_37XX_DVFS_LOAD_2)
++ *offset += ARMADA_37XX_NB_CONFIG_SHIFT;
++}
++
++static bool armada_3700_pm_dvfs_is_enabled(struct regmap *base)
++{
++ unsigned int val, reg = ARMADA_37XX_NB_DYN_MOD;
++
++ if (IS_ERR(base))
++ return false;
++
++ regmap_read(base, reg, &val);
++
++ return !!(val & BIT(ARMADA_37XX_NB_DFS_EN));
++}
++
++static unsigned int armada_3700_pm_dvfs_get_cpu_div(struct regmap *base)
++{
++ unsigned int reg = ARMADA_37XX_NB_CPU_LOAD;
++ unsigned int offset = ARMADA_37XX_NB_TBG_DIV_OFF;
++ unsigned int load_level, div;
++
++ /*
++ * This function is always called after the function
++ * armada_3700_pm_dvfs_is_enabled, so no need to check again
++ * if the base is valid.
++ */
++ regmap_read(base, reg, &load_level);
++
++ /*
++ * The register and the offset inside this register accessed to
++ * read the current divider depend on the load level
++ */
++ load_level &= ARMADA_37XX_NB_CPU_LOAD_MASK;
++ armada_3700_pm_dvfs_update_regs(load_level, ®, &offset);
++
++ regmap_read(base, reg, &div);
++
++ return (div >> offset) & ARMADA_37XX_NB_TBG_DIV_MASK;
++}
++
++static unsigned int armada_3700_pm_dvfs_get_cpu_parent(struct regmap *base)
++{
++ unsigned int reg = ARMADA_37XX_NB_CPU_LOAD;
++ unsigned int offset = ARMADA_37XX_NB_TBG_SEL_OFF;
++ unsigned int load_level, sel;
++
++ /*
++ * This function is always called after the function
++ * armada_3700_pm_dvfs_is_enabled, so no need to check again
++ * if the base is valid
++ */
++ regmap_read(base, reg, &load_level);
++
++ /*
++ * The register and the offset inside this register accessed to
++ * read the current divider depend on the load level
++ */
++ load_level &= ARMADA_37XX_NB_CPU_LOAD_MASK;
++ armada_3700_pm_dvfs_update_regs(load_level, ®, &offset);
++
++ regmap_read(base, reg, &sel);
++
++ return (sel >> offset) & ARMADA_37XX_NB_TBG_SEL_MASK;
++}
++
+ static u8 clk_pm_cpu_get_parent(struct clk_hw *hw)
+ {
+ struct clk_pm_cpu *pm_cpu = to_clk_pm_cpu(hw);
+ int num_parents = clk_hw_get_num_parents(hw);
+ u32 val;
+
+- val = readl(pm_cpu->reg_mux) >> pm_cpu->shift_mux;
+- val &= pm_cpu->mask_mux;
++ if (armada_3700_pm_dvfs_is_enabled(pm_cpu->nb_pm_base)) {
++ val = armada_3700_pm_dvfs_get_cpu_parent(pm_cpu->nb_pm_base);
++ } else {
++ val = readl(pm_cpu->reg_mux) >> pm_cpu->shift_mux;
++ val &= pm_cpu->mask_mux;
++ }
+
+ if (val >= num_parents)
+ return -EINVAL;
+@@ -331,19 +434,124 @@ static u8 clk_pm_cpu_get_parent(struct c
+ return val;
+ }
+
++static int clk_pm_cpu_set_parent(struct clk_hw *hw, u8 index)
++{
++ struct clk_pm_cpu *pm_cpu = to_clk_pm_cpu(hw);
++ struct regmap *base = pm_cpu->nb_pm_base;
++ int load_level;
++
++ /*
++ * We set the clock parent only if the DVFS is available but
++ * not enabled.
++ */
++ if (IS_ERR(base) || armada_3700_pm_dvfs_is_enabled(base))
++ return -EINVAL;
++
++ /* Set the parent clock for all the load level */
++ for (load_level = 0; load_level < LOAD_LEVEL_NR; load_level++) {
++ unsigned int reg, mask, val,
++ offset = ARMADA_37XX_NB_TBG_SEL_OFF;
++
++ armada_3700_pm_dvfs_update_regs(load_level, ®, &offset);
++
++ val = index << offset;
++ mask = ARMADA_37XX_NB_TBG_SEL_MASK << offset;
++ regmap_update_bits(base, reg, mask, val);
++ }
++ return 0;
++}
++
+ static unsigned long clk_pm_cpu_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+ {
+ struct clk_pm_cpu *pm_cpu = to_clk_pm_cpu(hw);
+ unsigned int div;
+
+- div = get_div(pm_cpu->reg_div, pm_cpu->shift_div);
+-
++ if (armada_3700_pm_dvfs_is_enabled(pm_cpu->nb_pm_base))
++ div = armada_3700_pm_dvfs_get_cpu_div(pm_cpu->nb_pm_base);
++ else
++ div = get_div(pm_cpu->reg_div, pm_cpu->shift_div);
+ return DIV_ROUND_UP_ULL((u64)parent_rate, div);
+ }
+
++static long clk_pm_cpu_round_rate(struct clk_hw *hw, unsigned long rate,
++ unsigned long *parent_rate)
++{
++ struct clk_pm_cpu *pm_cpu = to_clk_pm_cpu(hw);
++ struct regmap *base = pm_cpu->nb_pm_base;
++ unsigned int div = *parent_rate / rate;
++ unsigned int load_level;
++ /* only available when DVFS is enabled */
++ if (!armada_3700_pm_dvfs_is_enabled(base))
++ return -EINVAL;
++
++ for (load_level = 0; load_level < LOAD_LEVEL_NR; load_level++) {
++ unsigned int reg, val, offset = ARMADA_37XX_NB_TBG_DIV_OFF;
++
++ armada_3700_pm_dvfs_update_regs(load_level, ®, &offset);
++
++ regmap_read(base, reg, &val);
++
++ val >>= offset;
++ val &= ARMADA_37XX_NB_TBG_DIV_MASK;
++ if (val == div)
++ /*
++ * We found a load level matching the target
++ * divider, switch to this load level and
++ * return.
++ */
++ return *parent_rate / div;
++ }
++
++ /* We didn't find any valid divider */
++ return -EINVAL;
++}
++
++static int clk_pm_cpu_set_rate(struct clk_hw *hw, unsigned long rate,
++ unsigned long parent_rate)
++{
++ struct clk_pm_cpu *pm_cpu = to_clk_pm_cpu(hw);
++ struct regmap *base = pm_cpu->nb_pm_base;
++ unsigned int div = parent_rate / rate;
++ unsigned int load_level;
++
++ /* only available when DVFS is enabled */
++ if (!armada_3700_pm_dvfs_is_enabled(base))
++ return -EINVAL;
++
++ for (load_level = 0; load_level < LOAD_LEVEL_NR; load_level++) {
++ unsigned int reg, mask, val,
++ offset = ARMADA_37XX_NB_TBG_DIV_OFF;
++
++ armada_3700_pm_dvfs_update_regs(load_level, ®, &offset);
++
++ regmap_read(base, reg, &val);
++ val >>= offset;
++ val &= ARMADA_37XX_NB_TBG_DIV_MASK;
++
++ if (val == div) {
++ /*
++ * We found a load level matching the target
++ * divider, switch to this load level and
++ * return.
++ */
++ reg = ARMADA_37XX_NB_CPU_LOAD;
++ mask = ARMADA_37XX_NB_CPU_LOAD_MASK;
++ regmap_update_bits(base, reg, mask, load_level);
++
++ return rate;
++ }
++ }
++
++ /* We didn't find any valid divider */
++ return -EINVAL;
++}
++
+ static const struct clk_ops clk_pm_cpu_ops = {
+ .get_parent = clk_pm_cpu_get_parent,
++ .set_parent = clk_pm_cpu_set_parent,
++ .round_rate = clk_pm_cpu_round_rate,
++ .set_rate = clk_pm_cpu_set_rate,
+ .recalc_rate = clk_pm_cpu_recalc_rate,
+ };
+
+@@ -409,6 +617,7 @@ static int armada_3700_add_composite_clk
+ if (data->muxrate_hw) {
+ struct clk_pm_cpu *pmcpu_clk;
+ struct clk_hw *muxrate_hw = data->muxrate_hw;
++ struct regmap *map;
+
+ pmcpu_clk = to_clk_pm_cpu(muxrate_hw);
+ pmcpu_clk->reg_mux = reg + (u64)pmcpu_clk->reg_mux;
+@@ -418,6 +627,10 @@ static int armada_3700_add_composite_clk
+ rate_hw = muxrate_hw;
+ mux_ops = muxrate_hw->init->ops;
+ rate_ops = muxrate_hw->init->ops;
++
++ map = syscon_regmap_lookup_by_compatible(
++ "marvell,armada-3700-nb-pm");
++ pmcpu_clk->nb_pm_base = map;
+ }
+
+ *hw = clk_hw_register_composite(dev, data->name, data->parent_names,
diff --git a/target/linux/mvebu/patches-4.14/503-cpufreq-Add-DVFS-support-for-Armada-37xx.patch b/target/linux/mvebu/patches-4.14/503-cpufreq-Add-DVFS-support-for-Armada-37xx.patch
new file mode 100644
index 0000000000..11562c582b
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/503-cpufreq-Add-DVFS-support-for-Armada-37xx.patch
@@ -0,0 +1,297 @@
+From 92ce45fb875d7c3e021cc454482fe0687ff54f29 Mon Sep 17 00:00:00 2001
+From: Gregory CLEMENT <gregory.clement at free-electrons.com>
+Date: Thu, 14 Dec 2017 16:00:05 +0100
+Subject: cpufreq: Add DVFS support for Armada 37xx
+
+This patch adds DVFS support for the Armada 37xx SoCs
+
+There are up to four CPU frequency loads for Armada 37xx controlled by
+the hardware.
+
+This driver associates the CPU load level to a frequency, then the
+hardware will switch while selecting a load level.
+
+The hardware also can associate a voltage for each level (AVS support)
+but it is not yet supported
+
+Tested-by: Andre Heider <a.heider at gmail.com>
+Acked-by: Viresh Kumar <viresh.kumar at linaro.org>
+Signed-off-by: Gregory CLEMENT <gregory.clement at free-electrons.com>
+Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki at intel.com>
+---
+ drivers/cpufreq/Kconfig.arm | 7 +
+ drivers/cpufreq/Makefile | 1 +
+ drivers/cpufreq/armada-37xx-cpufreq.c | 241 ++++++++++++++++++++++++++++++++++
+ 3 files changed, 249 insertions(+)
+ create mode 100644 drivers/cpufreq/armada-37xx-cpufreq.c
+
+--- a/drivers/cpufreq/Kconfig.arm
++++ b/drivers/cpufreq/Kconfig.arm
+@@ -2,6 +2,13 @@
+ # ARM CPU Frequency scaling drivers
+ #
+
++config ARM_ARMADA_37XX_CPUFREQ
++ tristate "Armada 37xx CPUFreq support"
++ depends on ARCH_MVEBU
++ help
++ This adds the CPUFreq driver support for Marvell Armada 37xx SoCs.
++ The Armada 37xx PMU supports 4 frequency and VDD levels.
++
+ # big LITTLE core layer and glue drivers
+ config ARM_BIG_LITTLE_CPUFREQ
+ tristate "Generic ARM big LITTLE CPUfreq driver"
+--- a/drivers/cpufreq/Makefile
++++ b/drivers/cpufreq/Makefile
+@@ -52,6 +52,7 @@ obj-$(CONFIG_ARM_BIG_LITTLE_CPUFREQ) +=
+ # LITTLE drivers, so that it is probed last.
+ obj-$(CONFIG_ARM_DT_BL_CPUFREQ) += arm_big_little_dt.o
+
++obj-$(CONFIG_ARM_ARMADA_37XX_CPUFREQ) += armada-37xx-cpufreq.o
+ obj-$(CONFIG_ARM_BRCMSTB_AVS_CPUFREQ) += brcmstb-avs-cpufreq.o
+ obj-$(CONFIG_ARCH_DAVINCI) += davinci-cpufreq.o
+ obj-$(CONFIG_ARM_EXYNOS5440_CPUFREQ) += exynos5440-cpufreq.o
+--- /dev/null
++++ b/drivers/cpufreq/armada-37xx-cpufreq.c
+@@ -0,0 +1,241 @@
++// SPDX-License-Identifier: GPL-2.0+
++/*
++ * CPU frequency scaling support for Armada 37xx platform.
++ *
++ * Copyright (C) 2017 Marvell
++ *
++ * Gregory CLEMENT <gregory.clement at free-electrons.com>
++ */
++
++#include <linux/clk.h>
++#include <linux/cpu.h>
++#include <linux/cpufreq.h>
++#include <linux/err.h>
++#include <linux/interrupt.h>
++#include <linux/io.h>
++#include <linux/mfd/syscon.h>
++#include <linux/module.h>
++#include <linux/of_address.h>
++#include <linux/of_device.h>
++#include <linux/of_irq.h>
++#include <linux/platform_device.h>
++#include <linux/pm_opp.h>
++#include <linux/regmap.h>
++#include <linux/slab.h>
++
++/* Power management in North Bridge register set */
++#define ARMADA_37XX_NB_L0L1 0x18
++#define ARMADA_37XX_NB_L2L3 0x1C
++#define ARMADA_37XX_NB_TBG_DIV_OFF 13
++#define ARMADA_37XX_NB_TBG_DIV_MASK 0x7
++#define ARMADA_37XX_NB_CLK_SEL_OFF 11
++#define ARMADA_37XX_NB_CLK_SEL_MASK 0x1
++#define ARMADA_37XX_NB_CLK_SEL_TBG 0x1
++#define ARMADA_37XX_NB_TBG_SEL_OFF 9
++#define ARMADA_37XX_NB_TBG_SEL_MASK 0x3
++#define ARMADA_37XX_NB_VDD_SEL_OFF 6
++#define ARMADA_37XX_NB_VDD_SEL_MASK 0x3
++#define ARMADA_37XX_NB_CONFIG_SHIFT 16
++#define ARMADA_37XX_NB_DYN_MOD 0x24
++#define ARMADA_37XX_NB_CLK_SEL_EN BIT(26)
++#define ARMADA_37XX_NB_TBG_EN BIT(28)
++#define ARMADA_37XX_NB_DIV_EN BIT(29)
++#define ARMADA_37XX_NB_VDD_EN BIT(30)
++#define ARMADA_37XX_NB_DFS_EN BIT(31)
++#define ARMADA_37XX_NB_CPU_LOAD 0x30
++#define ARMADA_37XX_NB_CPU_LOAD_MASK 0x3
++#define ARMADA_37XX_DVFS_LOAD_0 0
++#define ARMADA_37XX_DVFS_LOAD_1 1
++#define ARMADA_37XX_DVFS_LOAD_2 2
++#define ARMADA_37XX_DVFS_LOAD_3 3
++
++/*
++ * On Armada 37xx the Power management manages 4 level of CPU load,
++ * each level can be associated with a CPU clock source, a CPU
++ * divider, a VDD level, etc...
++ */
++#define LOAD_LEVEL_NR 4
++
++struct armada_37xx_dvfs {
++ u32 cpu_freq_max;
++ u8 divider[LOAD_LEVEL_NR];
++};
++
++static struct armada_37xx_dvfs armada_37xx_dvfs[] = {
++ {.cpu_freq_max = 1200*1000*1000, .divider = {1, 2, 4, 6} },
++ {.cpu_freq_max = 1000*1000*1000, .divider = {1, 2, 4, 5} },
++ {.cpu_freq_max = 800*1000*1000, .divider = {1, 2, 3, 4} },
++ {.cpu_freq_max = 600*1000*1000, .divider = {2, 4, 5, 6} },
++};
++
++static struct armada_37xx_dvfs *armada_37xx_cpu_freq_info_get(u32 freq)
++{
++ int i;
++
++ for (i = 0; i < ARRAY_SIZE(armada_37xx_dvfs); i++) {
++ if (freq == armada_37xx_dvfs[i].cpu_freq_max)
++ return &armada_37xx_dvfs[i];
++ }
++
++ pr_err("Unsupported CPU frequency %d MHz\n", freq/1000000);
++ return NULL;
++}
++
++/*
++ * Setup the four level managed by the hardware. Once the four level
++ * will be configured then the DVFS will be enabled.
++ */
++static void __init armada37xx_cpufreq_dvfs_setup(struct regmap *base,
++ struct clk *clk, u8 *divider)
++{
++ int load_lvl;
++ struct clk *parent;
++
++ for (load_lvl = 0; load_lvl < LOAD_LEVEL_NR; load_lvl++) {
++ unsigned int reg, mask, val, offset = 0;
++
++ if (load_lvl <= ARMADA_37XX_DVFS_LOAD_1)
++ reg = ARMADA_37XX_NB_L0L1;
++ else
++ reg = ARMADA_37XX_NB_L2L3;
++
++ if (load_lvl == ARMADA_37XX_DVFS_LOAD_0 ||
++ load_lvl == ARMADA_37XX_DVFS_LOAD_2)
++ offset += ARMADA_37XX_NB_CONFIG_SHIFT;
++
++ /* Set cpu clock source, for all the level we use TBG */
++ val = ARMADA_37XX_NB_CLK_SEL_TBG << ARMADA_37XX_NB_CLK_SEL_OFF;
++ mask = (ARMADA_37XX_NB_CLK_SEL_MASK
++ << ARMADA_37XX_NB_CLK_SEL_OFF);
++
++ /*
++ * Set cpu divider based on the pre-computed array in
++ * order to have balanced step.
++ */
++ val |= divider[load_lvl] << ARMADA_37XX_NB_TBG_DIV_OFF;
++ mask |= (ARMADA_37XX_NB_TBG_DIV_MASK
++ << ARMADA_37XX_NB_TBG_DIV_OFF);
++
++ /* Set VDD divider which is actually the load level. */
++ val |= load_lvl << ARMADA_37XX_NB_VDD_SEL_OFF;
++ mask |= (ARMADA_37XX_NB_VDD_SEL_MASK
++ << ARMADA_37XX_NB_VDD_SEL_OFF);
++
++ val <<= offset;
++ mask <<= offset;
++
++ regmap_update_bits(base, reg, mask, val);
++ }
++
++ /*
++ * Set cpu clock source, for all the level we keep the same
++ * clock source that the one already configured. For this one
++ * we need to use the clock framework
++ */
++ parent = clk_get_parent(clk);
++ clk_set_parent(clk, parent);
++}
++
++static void __init armada37xx_cpufreq_disable_dvfs(struct regmap *base)
++{
++ unsigned int reg = ARMADA_37XX_NB_DYN_MOD,
++ mask = ARMADA_37XX_NB_DFS_EN;
++
++ regmap_update_bits(base, reg, mask, 0);
++}
++
++static void __init armada37xx_cpufreq_enable_dvfs(struct regmap *base)
++{
++ unsigned int val, reg = ARMADA_37XX_NB_CPU_LOAD,
++ mask = ARMADA_37XX_NB_CPU_LOAD_MASK;
++
++ /* Start with the highest load (0) */
++ val = ARMADA_37XX_DVFS_LOAD_0;
++ regmap_update_bits(base, reg, mask, val);
++
++ /* Now enable DVFS for the CPUs */
++ reg = ARMADA_37XX_NB_DYN_MOD;
++ mask = ARMADA_37XX_NB_CLK_SEL_EN | ARMADA_37XX_NB_TBG_EN |
++ ARMADA_37XX_NB_DIV_EN | ARMADA_37XX_NB_VDD_EN |
++ ARMADA_37XX_NB_DFS_EN;
++
++ regmap_update_bits(base, reg, mask, mask);
++}
++
++static int __init armada37xx_cpufreq_driver_init(void)
++{
++ struct armada_37xx_dvfs *dvfs;
++ struct platform_device *pdev;
++ unsigned int cur_frequency;
++ struct regmap *nb_pm_base;
++ struct device *cpu_dev;
++ int load_lvl, ret;
++ struct clk *clk;
++
++ nb_pm_base =
++ syscon_regmap_lookup_by_compatible("marvell,armada-3700-nb-pm");
++
++ if (IS_ERR(nb_pm_base))
++ return -ENODEV;
++
++ /* Before doing any configuration on the DVFS first, disable it */
++ armada37xx_cpufreq_disable_dvfs(nb_pm_base);
++
++ /*
++ * On CPU 0 register the operating points supported (which are
++ * the nominal CPU frequency and full integer divisions of
++ * it).
++ */
++ cpu_dev = get_cpu_device(0);
++ if (!cpu_dev) {
++ dev_err(cpu_dev, "Cannot get CPU\n");
++ return -ENODEV;
++ }
++
++ clk = clk_get(cpu_dev, 0);
++ if (IS_ERR(clk)) {
++ dev_err(cpu_dev, "Cannot get clock for CPU0\n");
++ return PTR_ERR(clk);
++ }
++
++ /* Get nominal (current) CPU frequency */
++ cur_frequency = clk_get_rate(clk);
++ if (!cur_frequency) {
++ dev_err(cpu_dev, "Failed to get clock rate for CPU\n");
++ return -EINVAL;
++ }
++
++ dvfs = armada_37xx_cpu_freq_info_get(cur_frequency);
++ if (!dvfs)
++ return -EINVAL;
++
++ armada37xx_cpufreq_dvfs_setup(nb_pm_base, clk, dvfs->divider);
++
++ for (load_lvl = ARMADA_37XX_DVFS_LOAD_0; load_lvl < LOAD_LEVEL_NR;
++ load_lvl++) {
++ unsigned long freq = cur_frequency / dvfs->divider[load_lvl];
++
++ ret = dev_pm_opp_add(cpu_dev, freq, 0);
++ if (ret) {
++ /* clean-up the already added opp before leaving */
++ while (load_lvl-- > ARMADA_37XX_DVFS_LOAD_0) {
++ freq = cur_frequency / dvfs->divider[load_lvl];
++ dev_pm_opp_remove(cpu_dev, freq);
++ }
++ return ret;
++ }
++ }
++
++ /* Now that everything is setup, enable the DVFS at hardware level */
++ armada37xx_cpufreq_enable_dvfs(nb_pm_base);
++
++ pdev = platform_device_register_simple("cpufreq-dt", -1, NULL, 0);
++
++ return PTR_ERR_OR_ZERO(pdev);
++}
++/* late_initcall, to guarantee the driver is loaded after A37xx clock driver */
++late_initcall(armada37xx_cpufreq_driver_init);
++
++MODULE_AUTHOR("Gregory CLEMENT <gregory.clement at free-electrons.com>");
++MODULE_DESCRIPTION("Armada 37xx cpufreq driver");
++MODULE_LICENSE("GPL");
diff --git a/target/linux/mvebu/patches-4.14/504-spi-a3700-Change-SPI-mode-before-asserting-chip-sele.patch b/target/linux/mvebu/patches-4.14/504-spi-a3700-Change-SPI-mode-before-asserting-chip-sele.patch
new file mode 100644
index 0000000000..3ac7091188
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/504-spi-a3700-Change-SPI-mode-before-asserting-chip-sele.patch
@@ -0,0 +1,70 @@
+From dd7aa8d4b53b3484ba31ba56f3ff1be7deb38530 Mon Sep 17 00:00:00 2001
+From: Maxime Chevallier <maxime.chevallier at smile.fr>
+Date: Tue, 10 Oct 2017 10:43:18 +0200
+Subject: spi: a3700: Change SPI mode before asserting chip-select
+
+The spi device mode should be configured in the controller before the
+chip-select is asserted, so that a clock polarity configuration change
+is not interpreted as a clock tick by the device.
+
+This patch moves the mode setting to the 'prepare_message' function
+instead of the 'transfer_one' function.
+
+By doing so, this patch also removes redundant code in
+a3700_spi_clock_set.
+
+This was tested on EspressoBin board, with spidev.
+
+Signed-off-by: Maxime Chevallier <maxime.chevallier at smile.fr>
+Signed-off-by: Mark Brown <broonie at kernel.org>
+---
+ drivers/spi/spi-armada-3700.c | 17 ++++-------------
+ 1 file changed, 4 insertions(+), 13 deletions(-)
+
+--- a/drivers/spi/spi-armada-3700.c
++++ b/drivers/spi/spi-armada-3700.c
+@@ -214,7 +214,7 @@ static void a3700_spi_mode_set(struct a3
+ }
+
+ static void a3700_spi_clock_set(struct a3700_spi *a3700_spi,
+- unsigned int speed_hz, u16 mode)
++ unsigned int speed_hz)
+ {
+ u32 val;
+ u32 prescale;
+@@ -239,17 +239,6 @@ static void a3700_spi_clock_set(struct a
+ val |= A3700_SPI_CLK_CAPT_EDGE;
+ spireg_write(a3700_spi, A3700_SPI_IF_TIME_REG, val);
+ }
+-
+- val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+- val &= ~(A3700_SPI_CLK_POL | A3700_SPI_CLK_PHA);
+-
+- if (mode & SPI_CPOL)
+- val |= A3700_SPI_CLK_POL;
+-
+- if (mode & SPI_CPHA)
+- val |= A3700_SPI_CLK_PHA;
+-
+- spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+ }
+
+ static void a3700_spi_bytelen_set(struct a3700_spi *a3700_spi, unsigned int len)
+@@ -431,7 +420,7 @@ static void a3700_spi_transfer_setup(str
+
+ a3700_spi = spi_master_get_devdata(spi->master);
+
+- a3700_spi_clock_set(a3700_spi, xfer->speed_hz, spi->mode);
++ a3700_spi_clock_set(a3700_spi, xfer->speed_hz);
+
+ byte_len = xfer->bits_per_word >> 3;
+
+@@ -592,6 +581,8 @@ static int a3700_spi_prepare_message(str
+
+ a3700_spi_bytelen_set(a3700_spi, 4);
+
++ a3700_spi_mode_set(a3700_spi, spi->mode);
++
+ return 0;
+ }
+
diff --git a/target/linux/mvebu/patches-4.14/505-arm64-dts-marvell-Fix-A37xx-UART0-register-size.patch b/target/linux/mvebu/patches-4.14/505-arm64-dts-marvell-Fix-A37xx-UART0-register-size.patch
new file mode 100644
index 0000000000..9e2b1c14eb
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/505-arm64-dts-marvell-Fix-A37xx-UART0-register-size.patch
@@ -0,0 +1,39 @@
+From c737abc193d16e62e23e2fb585b8b7398ab380d8 Mon Sep 17 00:00:00 2001
+From: allen yan <yanwei at marvell.com>
+Date: Thu, 7 Sep 2017 15:04:53 +0200
+Subject: arm64: dts: marvell: Fix A37xx UART0 register size
+
+Armada-37xx UART0 registers are 0x200 bytes wide. Right next to them are
+the UART1 registers that should not be declared in this node.
+
+Update the example in DT bindings document accordingly.
+
+Signed-off-by: allen yan <yanwei at marvell.com>
+Signed-off-by: Miquel Raynal <miquel.raynal at free-electrons.com>
+Signed-off-by: Gregory CLEMENT <gregory.clement at free-electrons.com>
+---
+ Documentation/devicetree/bindings/serial/mvebu-uart.txt | 2 +-
+ arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 2 +-
+ 2 files changed, 2 insertions(+), 2 deletions(-)
+
+--- a/Documentation/devicetree/bindings/serial/mvebu-uart.txt
++++ b/Documentation/devicetree/bindings/serial/mvebu-uart.txt
+@@ -8,6 +8,6 @@ Required properties:
+ Example:
+ serial at 12000 {
+ compatible = "marvell,armada-3700-uart";
+- reg = <0x12000 0x400>;
++ reg = <0x12000 0x200>;
+ interrupts = <43>;
+ };
+--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
++++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+@@ -134,7 +134,7 @@
+
+ uart0: serial at 12000 {
+ compatible = "marvell,armada-3700-uart";
+- reg = <0x12000 0x400>;
++ reg = <0x12000 0x200>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
diff --git a/target/linux/mvebu/patches-4.14/506-arm64-dts-marvell-armada-37xx-add-UART-clock.patch b/target/linux/mvebu/patches-4.14/506-arm64-dts-marvell-armada-37xx-add-UART-clock.patch
new file mode 100644
index 0000000000..47e0751c5f
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/506-arm64-dts-marvell-armada-37xx-add-UART-clock.patch
@@ -0,0 +1,27 @@
+From 2ff0d0b5bb397c3dc5c9b97bd0f20948f0b77740 Mon Sep 17 00:00:00 2001
+From: Miquel Raynal <miquel.raynal at free-electrons.com>
+Date: Fri, 13 Oct 2017 11:01:57 +0200
+Subject: arm64: dts: marvell: armada-37xx: add UART clock
+
+Add the missing clock property to armada-3700 UART node.
+
+This clock will be used to derive the prescaler value to comply with
+the requested baudrate.
+
+Signed-off-by: Miquel Raynal <miquel.raynal at free-electrons.com>
+Acked-by: Gregory CLEMENT <gregory.clement at free-electrons.com>
+Signed-off-by: Gregory CLEMENT <gregory.clement at free-electrons.com>
+---
+ arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 1 +
+ 1 file changed, 1 insertion(+)
+
+--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
++++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+@@ -135,6 +135,7 @@
+ uart0: serial at 12000 {
+ compatible = "marvell,armada-3700-uart";
+ reg = <0x12000 0x200>;
++ clocks = <&xtalclk>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
diff --git a/target/linux/mvebu/patches-4.14/507-arm64-dts-marvell-armada-37xx-add-nodes-allowing-cpu.patch b/target/linux/mvebu/patches-4.14/507-arm64-dts-marvell-armada-37xx-add-nodes-allowing-cpu.patch
new file mode 100644
index 0000000000..dd3727c554
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/507-arm64-dts-marvell-armada-37xx-add-nodes-allowing-cpu.patch
@@ -0,0 +1,48 @@
+From e8d66e7927b2a15310df0eb44a67d120ea147a59 Mon Sep 17 00:00:00 2001
+From: Gregory CLEMENT <gregory.clement at free-electrons.com>
+Date: Thu, 14 Dec 2017 16:00:06 +0100
+Subject: arm64: dts: marvell: armada-37xx: add nodes allowing cpufreq
+ support
+
+In order to be able to use cpu freq, we need to associate a clock to each
+CPU and to expose the power management registers.
+
+Signed-off-by: Gregory CLEMENT <gregory.clement at free-electrons.com>
+---
+ arch/arm64/boot/dts/marvell/armada-372x.dtsi | 1 +
+ arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 7 +++++++
+ 2 files changed, 8 insertions(+)
+
+--- a/arch/arm64/boot/dts/marvell/armada-372x.dtsi
++++ b/arch/arm64/boot/dts/marvell/armada-372x.dtsi
+@@ -56,6 +56,7 @@
+ device_type = "cpu";
+ compatible = "arm,cortex-a53","arm,armv8";
+ reg = <0x1>;
++ clocks = <&nb_periph_clk 16>;
+ enable-method = "psci";
+ };
+ };
+--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
++++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+@@ -64,6 +64,7 @@
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0>;
++ clocks = <&nb_periph_clk 16>;
+ enable-method = "psci";
+ };
+ };
+@@ -219,6 +220,12 @@
+ };
+ };
+
++ nb_pm: syscon at 14000 {
++ compatible = "marvell,armada-3700-nb-pm",
++ "syscon";
++ reg = <0x14000 0x60>;
++ };
++
+ pinctrl_sb: pinctrl at 18800 {
+ compatible = "marvell,armada3710-sb-pinctrl",
+ "syscon", "simple-mfd";
diff --git a/target/linux/mvebu/patches-4.14/520-arm64-dts-marvell-armada37xx-Add-eth0-alias.patch b/target/linux/mvebu/patches-4.14/520-arm64-dts-marvell-armada37xx-Add-eth0-alias.patch
new file mode 100644
index 0000000000..206caf2fce
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/520-arm64-dts-marvell-armada37xx-Add-eth0-alias.patch
@@ -0,0 +1,20 @@
+From be893f672e340b56ca60f2f6c32fdd713a5852f5 Mon Sep 17 00:00:00 2001
+From: Kevin Mihelich <kevin at archlinuxarm.org>
+Date: Tue, 4 Jul 2017 19:25:28 -0600
+Subject: arm64: dts: marvell: armada37xx: Add eth0 alias
+
+Signed-off-by: Kevin Mihelich <kevin at archlinuxarm.org>
+---
+ arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 1 +
+ 1 file changed, 1 insertion(+)
+
+--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
++++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+@@ -54,6 +54,7 @@
+ #size-cells = <2>;
+
+ aliases {
++ ethernet0 = ð0;
+ serial0 = &uart0;
+ };
+
diff --git a/target/linux/mvebu/patches-4.14/521-esporessobin-dt-enable-spi-nor-on-i2c.patch b/target/linux/mvebu/patches-4.14/521-esporessobin-dt-enable-spi-nor-on-i2c.patch
new file mode 100644
index 0000000000..3cabaa7a01
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/521-esporessobin-dt-enable-spi-nor-on-i2c.patch
@@ -0,0 +1,29 @@
+--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
++++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
+@@ -111,6 +111,26 @@
+ status = "okay";
+ };
+
++&spi0 {
++ status = "okay";
++
++ w25q32dw at 0 {
++ #address-cells = <1>;
++ #size-cells = <1>;
++ compatible = "jedec,spi-nor";
++ reg = <0>;
++ spi-max-frequency = <104000000>;
++ m25,fast-read;
++
++ pinctrl-names = "default";
++ pinctrl-0 = <&spi_quad_pins>;
++ };
++};
++
++&i2c0 {
++ status = "okay";
++};
++
+ &mdio {
+ switch0: switch0 at 1 {
+ compatible = "marvell,mv88e6085";
diff --git a/target/linux/mvebu/patches-4.14/522-PCI-aardvark-fix-logic-in-PCI-configuration-read-write-functions.patch b/target/linux/mvebu/patches-4.14/522-PCI-aardvark-fix-logic-in-PCI-configuration-read-write-functions.patch
new file mode 100644
index 0000000000..0dead7d61d
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/522-PCI-aardvark-fix-logic-in-PCI-configuration-read-write-functions.patch
@@ -0,0 +1,66 @@
+From patchwork Thu Sep 28 12:58:32 2017
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v2, 1/7] PCI: aardvark: fix logic in PCI configuration read/write
+ functions
+X-Patchwork-Submitter: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+X-Patchwork-Id: 819586
+Message-Id: <20170928125838.11887-2-thomas.petazzoni at free-electrons.com>
+To: Bjorn Helgaas <bhelgaas at google.com>, linux-pci at vger.kernel.org
+Cc: Jason Cooper <jason at lakedaemon.net>, Andrew Lunn <andrew at lunn.ch>,
+ Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>, Gregory Clement
+ <gregory.clement at free-electrons.com>,
+ Nadav Haklai <nadavh at marvell.com>, Hanna Hawa <hannah at marvell.com>,
+ Yehuda Yitschak <yehuday at marvell.com>,
+ linux-arm-kernel at lists.infradead.org, Antoine Tenart
+ <antoine.tenart at free-electrons.com>, =?utf-8?q?Miqu=C3=A8l_Raynal?=
+ <miquel.raynal at free-electrons.com>, Victor Gu <xigu at marvell.com>,
+ stable at vger.kernel.org, Thomas Petazzoni
+ <thomas.petazzoni at free-electrons.com>
+Date: Thu, 28 Sep 2017 14:58:32 +0200
+From: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+List-Id: <linux-pci.vger.kernel.org>
+
+From: Victor Gu <xigu at marvell.com>
+
+The PCI configuration space read/write functions were special casing
+the situation where PCI_SLOT(devfn) != 0, and returned
+PCIBIOS_DEVICE_NOT_FOUND in this case.
+
+However, will this is what is intended for the root bus, it is not
+intended for the child busses, as it prevents discovering devices with
+PCI_SLOT(x) != 0. Therefore, we return PCIBIOS_DEVICE_NOT_FOUND only
+if we're on the root bus.
+
+Fixes: 8c39d710363c1 ("PCI: aardvark: Add Aardvark PCI host controller driver")
+Cc: <stable at vger.kernel.org>
+Signed-off-by: Victor Gu <xigu at marvell.com>
+Reviewed-by: Wilson Ding <dingwei at marvell.com>
+Reviewed-by: Nadav Haklai <nadavh at marvell.com>
+[Thomas: tweak commit log.]
+Signed-off-by: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+---
+ drivers/pci/host/pci-aardvark.c | 4 ++--
+ 1 file changed, 2 insertions(+), 2 deletions(-)
+
+--- a/drivers/pci/host/pci-aardvark.c
++++ b/drivers/pci/host/pci-aardvark.c
+@@ -440,7 +440,7 @@ static int advk_pcie_rd_conf(struct pci_
+ u32 reg;
+ int ret;
+
+- if (PCI_SLOT(devfn) != 0) {
++ if ((bus->number == pcie->root_bus_nr) && (PCI_SLOT(devfn) != 0)) {
+ *val = 0xffffffff;
+ return PCIBIOS_DEVICE_NOT_FOUND;
+ }
+@@ -494,7 +494,7 @@ static int advk_pcie_wr_conf(struct pci_
+ int offset;
+ int ret;
+
+- if (PCI_SLOT(devfn) != 0)
++ if ((bus->number == pcie->root_bus_nr) && (PCI_SLOT(devfn) != 0))
+ return PCIBIOS_DEVICE_NOT_FOUND;
+
+ if (where % size)
diff --git a/target/linux/mvebu/patches-4.14/523-PCI-aardvark-set-PIO_ADDR_LS-correctly-in-advk_pcie_rd_conf.patch b/target/linux/mvebu/patches-4.14/523-PCI-aardvark-set-PIO_ADDR_LS-correctly-in-advk_pcie_rd_conf.patch
new file mode 100644
index 0000000000..238eb56269
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/523-PCI-aardvark-set-PIO_ADDR_LS-correctly-in-advk_pcie_rd_conf.patch
@@ -0,0 +1,53 @@
+From patchwork Thu Sep 28 12:58:33 2017
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v2,
+ 2/7] PCI: aardvark: set PIO_ADDR_LS correctly in advk_pcie_rd_conf()
+X-Patchwork-Submitter: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+X-Patchwork-Id: 819589
+Message-Id: <20170928125838.11887-3-thomas.petazzoni at free-electrons.com>
+To: Bjorn Helgaas <bhelgaas at google.com>, linux-pci at vger.kernel.org
+Cc: Jason Cooper <jason at lakedaemon.net>, Andrew Lunn <andrew at lunn.ch>,
+ Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>, Gregory Clement
+ <gregory.clement at free-electrons.com>,
+ Nadav Haklai <nadavh at marvell.com>, Hanna Hawa <hannah at marvell.com>,
+ Yehuda Yitschak <yehuday at marvell.com>,
+ linux-arm-kernel at lists.infradead.org, Antoine Tenart
+ <antoine.tenart at free-electrons.com>, =?utf-8?q?Miqu=C3=A8l_Raynal?=
+ <miquel.raynal at free-electrons.com>, Victor Gu <xigu at marvell.com>,
+ stable at vger.kernel.org, Thomas Petazzoni
+ <thomas.petazzoni at free-electrons.com>
+Date: Thu, 28 Sep 2017 14:58:33 +0200
+From: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+List-Id: <linux-pci.vger.kernel.org>
+
+From: Victor Gu <xigu at marvell.com>
+
+When setting the PIO_ADDR_LS register during a configuration read, we
+were properly passing the device number, function number and register
+number, but not the bus number, causing issues when reading the
+configuration of PCIe devices.
+
+Fixes: 8c39d710363c1 ("PCI: aardvark: Add Aardvark PCI host controller driver")
+Cc: <stable at vger.kernel.org>
+Signed-off-by: Victor Gu <xigu at marvell.com>
+Reviewed-by: Wilson Ding <dingwei at marvell.com>
+Reviewed-by: Nadav Haklai <nadavh at marvell.com>
+[Thomas: tweak commit log.]
+Signed-off-by: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+---
+ drivers/pci/host/pci-aardvark.c | 2 +-
+ 1 file changed, 1 insertion(+), 1 deletion(-)
+
+--- a/drivers/pci/host/pci-aardvark.c
++++ b/drivers/pci/host/pci-aardvark.c
+@@ -459,7 +459,7 @@ static int advk_pcie_rd_conf(struct pci_
+ advk_writel(pcie, reg, PIO_CTRL);
+
+ /* Program the address registers */
+- reg = PCIE_BDF(devfn) | PCIE_CONF_REG(where);
++ reg = PCIE_CONF_ADDR(bus->number, devfn, where);
+ advk_writel(pcie, reg, PIO_ADDR_LS);
+ advk_writel(pcie, 0, PIO_ADDR_MS);
+
diff --git a/target/linux/mvebu/patches-4.14/524-PCI-aardvark-set-host-and-device-to-the-same-MAX-payload-size.patch b/target/linux/mvebu/patches-4.14/524-PCI-aardvark-set-host-and-device-to-the-same-MAX-payload-size.patch
new file mode 100644
index 0000000000..f7e71aa060
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/524-PCI-aardvark-set-host-and-device-to-the-same-MAX-payload-size.patch
@@ -0,0 +1,137 @@
+From patchwork Thu Sep 28 12:58:34 2017
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v2,
+ 3/7] PCI: aardvark: set host and device to the same MAX payload size
+X-Patchwork-Submitter: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+X-Patchwork-Id: 819587
+Message-Id: <20170928125838.11887-4-thomas.petazzoni at free-electrons.com>
+To: Bjorn Helgaas <bhelgaas at google.com>, linux-pci at vger.kernel.org
+Cc: Jason Cooper <jason at lakedaemon.net>, Andrew Lunn <andrew at lunn.ch>,
+ Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>, Gregory Clement
+ <gregory.clement at free-electrons.com>,
+ Nadav Haklai <nadavh at marvell.com>, Hanna Hawa <hannah at marvell.com>,
+ Yehuda Yitschak <yehuday at marvell.com>,
+ linux-arm-kernel at lists.infradead.org, Antoine Tenart
+ <antoine.tenart at free-electrons.com>, =?utf-8?q?Miqu=C3=A8l_Raynal?=
+ <miquel.raynal at free-electrons.com>, Victor Gu <xigu at marvell.com>,
+ Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+Date: Thu, 28 Sep 2017 14:58:34 +0200
+From: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+List-Id: <linux-pci.vger.kernel.org>
+
+From: Victor Gu <xigu at marvell.com>
+
+Since the Aardvark does not implement a PCIe root bus, the Linux PCIe
+subsystem will not align the MAX payload size between the host and the
+device. This patch ensures that the host and device have the same MAX
+payload size, fixing a number of problems with various PCIe devices.
+
+This is part of fixing bug
+https://bugzilla.kernel.org/show_bug.cgi?id=196339, this commit was
+reported as the user to be important to get a Intel 7260 mini-PCIe
+WiFi card working.
+
+Fixes: Fixes: 8c39d710363c1 ("PCI: aardvark: Add Aardvark PCI host controller driver")
+Signed-off-by: Victor Gu <xigu at marvell.com>
+Reviewed-by: Evan Wang <xswang at marvell.com>
+Reviewed-by: Nadav Haklai <nadavh at marvell.com>
+[Thomas: tweak commit log.]
+Signed-off-by: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+---
+ drivers/pci/host/pci-aardvark.c | 60 ++++++++++++++++++++++++++++++++++++++++-
+ 1 file changed, 59 insertions(+), 1 deletion(-)
+
+--- a/drivers/pci/host/pci-aardvark.c
++++ b/drivers/pci/host/pci-aardvark.c
+@@ -30,8 +30,10 @@
+ #define PCIE_CORE_DEV_CTRL_STATS_REG 0xc8
+ #define PCIE_CORE_DEV_CTRL_STATS_RELAX_ORDER_DISABLE (0 << 4)
+ #define PCIE_CORE_DEV_CTRL_STATS_MAX_PAYLOAD_SZ_SHIFT 5
++#define PCIE_CORE_DEV_CTRL_STATS_MAX_PAYLOAD_SZ 0x2
+ #define PCIE_CORE_DEV_CTRL_STATS_SNOOP_DISABLE (0 << 11)
+ #define PCIE_CORE_DEV_CTRL_STATS_MAX_RD_REQ_SIZE_SHIFT 12
++#define PCIE_CORE_MPS_UNIT_BYTE 128
+ #define PCIE_CORE_LINK_CTRL_STAT_REG 0xd0
+ #define PCIE_CORE_LINK_L0S_ENTRY BIT(0)
+ #define PCIE_CORE_LINK_TRAINING BIT(5)
+@@ -297,7 +299,8 @@ static void advk_pcie_setup_hw(struct ad
+
+ /* Set PCIe Device Control and Status 1 PF0 register */
+ reg = PCIE_CORE_DEV_CTRL_STATS_RELAX_ORDER_DISABLE |
+- (7 << PCIE_CORE_DEV_CTRL_STATS_MAX_PAYLOAD_SZ_SHIFT) |
++ (PCIE_CORE_DEV_CTRL_STATS_MAX_PAYLOAD_SZ <<
++ PCIE_CORE_DEV_CTRL_STATS_MAX_PAYLOAD_SZ_SHIFT) |
+ PCIE_CORE_DEV_CTRL_STATS_SNOOP_DISABLE |
+ PCIE_CORE_DEV_CTRL_STATS_MAX_RD_REQ_SIZE_SHIFT;
+ advk_writel(pcie, reg, PCIE_CORE_DEV_CTRL_STATS_REG);
+@@ -879,6 +882,58 @@ out_release_res:
+ return err;
+ }
+
++static int advk_pcie_find_smpss(struct pci_dev *dev, void *data)
++{
++ u8 *smpss = data;
++
++ if (!dev)
++ return 0;
++
++ if (!pci_is_pcie(dev))
++ return 0;
++
++ if (*smpss > dev->pcie_mpss)
++ *smpss = dev->pcie_mpss;
++
++ return 0;
++}
++
++static int advk_pcie_bus_configure_mps(struct pci_dev *dev, void *data)
++{
++ int mps;
++
++ if (!dev)
++ return 0;
++
++ if (!pci_is_pcie(dev))
++ return 0;
++
++ mps = PCIE_CORE_MPS_UNIT_BYTE << *(u8 *)data;
++ pcie_set_mps(dev, mps);
++
++ return 0;
++}
++
++static void advk_pcie_configure_mps(struct pci_bus *bus, struct advk_pcie *pcie)
++{
++ u8 smpss = PCIE_CORE_DEV_CTRL_STATS_MAX_PAYLOAD_SZ;
++ u32 reg;
++
++ /* Find the minimal supported MAX payload size */
++ advk_pcie_find_smpss(bus->self, &smpss);
++ pci_walk_bus(bus, advk_pcie_find_smpss, &smpss);
++
++ /* Configure RC MAX payload size */
++ reg = advk_readl(pcie, PCIE_CORE_DEV_CTRL_STATS_REG);
++ reg &= ~PCI_EXP_DEVCTL_PAYLOAD;
++ reg |= smpss << PCIE_CORE_DEV_CTRL_STATS_MAX_PAYLOAD_SZ_SHIFT;
++ advk_writel(pcie, reg, PCIE_CORE_DEV_CTRL_STATS_REG);
++
++ /* Configure device MAX payload size */
++ advk_pcie_bus_configure_mps(bus->self, &smpss);
++ pci_walk_bus(bus, advk_pcie_bus_configure_mps, &smpss);
++}
++
+ static int advk_pcie_probe(struct platform_device *pdev)
+ {
+ struct device *dev = &pdev->dev;
+@@ -952,6 +1007,9 @@ static int advk_pcie_probe(struct platfo
+ list_for_each_entry(child, &bus->children, node)
+ pcie_bus_configure_settings(child);
+
++ /* Configure the MAX pay load size */
++ advk_pcie_configure_mps(bus, pcie);
++
+ pci_bus_add_devices(bus);
+ return 0;
+ }
diff --git a/target/linux/mvebu/patches-4.14/525-PCI-aardvark-use-isr1-instead-of-isr0-interrupt-in-legacy-irq-mode.patch b/target/linux/mvebu/patches-4.14/525-PCI-aardvark-use-isr1-instead-of-isr0-interrupt-in-legacy-irq-mode.patch
new file mode 100644
index 0000000000..777a078ef9
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/525-PCI-aardvark-use-isr1-instead-of-isr0-interrupt-in-legacy-irq-mode.patch
@@ -0,0 +1,143 @@
+From patchwork Thu Sep 28 12:58:35 2017
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v2,
+ 4/7] PCI: aardvark: use isr1 instead of isr0 interrupt in legacy irq
+ mode
+X-Patchwork-Submitter: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+X-Patchwork-Id: 819592
+Message-Id: <20170928125838.11887-5-thomas.petazzoni at free-electrons.com>
+To: Bjorn Helgaas <bhelgaas at google.com>, linux-pci at vger.kernel.org
+Cc: Jason Cooper <jason at lakedaemon.net>, Andrew Lunn <andrew at lunn.ch>,
+ Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>, Gregory Clement
+ <gregory.clement at free-electrons.com>,
+ Nadav Haklai <nadavh at marvell.com>, Hanna Hawa <hannah at marvell.com>,
+ Yehuda Yitschak <yehuday at marvell.com>,
+ linux-arm-kernel at lists.infradead.org, Antoine Tenart
+ <antoine.tenart at free-electrons.com>, =?utf-8?q?Miqu=C3=A8l_Raynal?=
+ <miquel.raynal at free-electrons.com>, Victor Gu <xigu at marvell.com>,
+ Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+Date: Thu, 28 Sep 2017 14:58:35 +0200
+From: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+List-Id: <linux-pci.vger.kernel.org>
+
+From: Victor Gu <xigu at marvell.com>
+
+The Aardvark has two interrupts sets:
+
+ - first set is bit[23:16] of PCIe ISR 0 register(RD0074840h)
+
+ - second set is bit[11:8] of PCIe ISR 1 register(RD0074848h)
+
+Only one set should be used, while another set should be masked.
+
+The second set, ISR1, is more advanced, the Legacy INT_X status bit is
+asserted once Assert_INTX message is received, and de-asserted after
+Deassert_INTX message is received. Therefore, it matches what the
+driver is currently doing in the ->irq_mask() and ->irq_unmask()
+functions. The ISR0 requires additional work to deassert the
+interrupt, which the driver doesn't do currently.
+
+This commit resolves a number of issues with legacy interrupts.
+
+This is part of fixing bug
+https://bugzilla.kernel.org/show_bug.cgi?id=196339, this commit was
+reported as the user to be important to get a Intel 7260 mini-PCIe
+WiFi card working.
+
+Fixes: 8c39d710363c1 ("PCI: aardvark: Add Aardvark PCI host controller driver")
+Signed-off-by: Victor Gu <xigu at marvell.com>
+Reviewed-by: Evan Wang <xswang at marvell.com>
+Reviewed-by: Nadav Haklai <nadavh at marvell.com>
+[Thomas: tweak commit log.]
+Signed-off-by: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+---
+ drivers/pci/host/pci-aardvark.c | 41 ++++++++++++++++++++++++-----------------
+ 1 file changed, 24 insertions(+), 17 deletions(-)
+
+--- a/drivers/pci/host/pci-aardvark.c
++++ b/drivers/pci/host/pci-aardvark.c
+@@ -105,7 +105,8 @@
+ #define PCIE_ISR1_MASK_REG (CONTROL_BASE_ADDR + 0x4C)
+ #define PCIE_ISR1_POWER_STATE_CHANGE BIT(4)
+ #define PCIE_ISR1_FLUSH BIT(5)
+-#define PCIE_ISR1_ALL_MASK GENMASK(5, 4)
++#define PCIE_ISR1_INTX_ASSERT(val) BIT(8 + (val))
++#define PCIE_ISR1_ALL_MASK GENMASK(11, 4)
+ #define PCIE_MSI_ADDR_LOW_REG (CONTROL_BASE_ADDR + 0x50)
+ #define PCIE_MSI_ADDR_HIGH_REG (CONTROL_BASE_ADDR + 0x54)
+ #define PCIE_MSI_STATUS_REG (CONTROL_BASE_ADDR + 0x58)
+@@ -615,9 +616,9 @@ static void advk_pcie_irq_mask(struct ir
+ irq_hw_number_t hwirq = irqd_to_hwirq(d);
+ u32 mask;
+
+- mask = advk_readl(pcie, PCIE_ISR0_MASK_REG);
+- mask |= PCIE_ISR0_INTX_ASSERT(hwirq);
+- advk_writel(pcie, mask, PCIE_ISR0_MASK_REG);
++ mask = advk_readl(pcie, PCIE_ISR1_MASK_REG);
++ mask |= PCIE_ISR1_INTX_ASSERT(hwirq);
++ advk_writel(pcie, mask, PCIE_ISR1_MASK_REG);
+ }
+
+ static void advk_pcie_irq_unmask(struct irq_data *d)
+@@ -626,9 +627,9 @@ static void advk_pcie_irq_unmask(struct
+ irq_hw_number_t hwirq = irqd_to_hwirq(d);
+ u32 mask;
+
+- mask = advk_readl(pcie, PCIE_ISR0_MASK_REG);
+- mask &= ~PCIE_ISR0_INTX_ASSERT(hwirq);
+- advk_writel(pcie, mask, PCIE_ISR0_MASK_REG);
++ mask = advk_readl(pcie, PCIE_ISR1_MASK_REG);
++ mask &= ~PCIE_ISR1_INTX_ASSERT(hwirq);
++ advk_writel(pcie, mask, PCIE_ISR1_MASK_REG);
+ }
+
+ static int advk_pcie_irq_map(struct irq_domain *h,
+@@ -771,29 +772,35 @@ static void advk_pcie_handle_msi(struct
+
+ static void advk_pcie_handle_int(struct advk_pcie *pcie)
+ {
+- u32 val, mask, status;
++ u32 isr0_val, isr0_mask, isr0_status;
++ u32 isr1_val, isr1_mask, isr1_status;
+ int i, virq;
+
+- val = advk_readl(pcie, PCIE_ISR0_REG);
+- mask = advk_readl(pcie, PCIE_ISR0_MASK_REG);
+- status = val & ((~mask) & PCIE_ISR0_ALL_MASK);
+-
+- if (!status) {
+- advk_writel(pcie, val, PCIE_ISR0_REG);
++ isr0_val = advk_readl(pcie, PCIE_ISR0_REG);
++ isr0_mask = advk_readl(pcie, PCIE_ISR0_MASK_REG);
++ isr0_status = isr0_val & ((~isr0_mask) & PCIE_ISR0_ALL_MASK);
++
++ isr1_val = advk_readl(pcie, PCIE_ISR1_REG);
++ isr1_mask = advk_readl(pcie, PCIE_ISR1_MASK_REG);
++ isr1_status = isr1_val & ((~isr1_mask) & PCIE_ISR1_ALL_MASK);
++
++ if (!isr0_status && !isr1_status) {
++ advk_writel(pcie, isr0_val, PCIE_ISR0_REG);
++ advk_writel(pcie, isr1_val, PCIE_ISR1_REG);
+ return;
+ }
+
+ /* Process MSI interrupts */
+- if (status & PCIE_ISR0_MSI_INT_PENDING)
++ if (isr0_status & PCIE_ISR0_MSI_INT_PENDING)
+ advk_pcie_handle_msi(pcie);
+
+ /* Process legacy interrupts */
+ for (i = 0; i < PCI_NUM_INTX; i++) {
+- if (!(status & PCIE_ISR0_INTX_ASSERT(i)))
++ if (!(isr1_status & PCIE_ISR1_INTX_ASSERT(i)))
+ continue;
+
+- advk_writel(pcie, PCIE_ISR0_INTX_ASSERT(i),
+- PCIE_ISR0_REG);
++ advk_writel(pcie, PCIE_ISR1_INTX_ASSERT(i),
++ PCIE_ISR1_REG);
+
+ virq = irq_find_mapping(pcie->irq_domain, i);
+ generic_handle_irq(virq);
diff --git a/target/linux/mvebu/patches-4.14/526-PCI-aardvark-disable-LOS-state-by-default.patch b/target/linux/mvebu/patches-4.14/526-PCI-aardvark-disable-LOS-state-by-default.patch
new file mode 100644
index 0000000000..0ee4af4e8d
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/526-PCI-aardvark-disable-LOS-state-by-default.patch
@@ -0,0 +1,55 @@
+From patchwork Thu Sep 28 12:58:36 2017
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v2,5/7] PCI: aardvark: disable LOS state by default
+X-Patchwork-Submitter: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+X-Patchwork-Id: 819590
+Message-Id: <20170928125838.11887-6-thomas.petazzoni at free-electrons.com>
+To: Bjorn Helgaas <bhelgaas at google.com>, linux-pci at vger.kernel.org
+Cc: Jason Cooper <jason at lakedaemon.net>, Andrew Lunn <andrew at lunn.ch>,
+ Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>, Gregory Clement
+ <gregory.clement at free-electrons.com>,
+ Nadav Haklai <nadavh at marvell.com>, Hanna Hawa <hannah at marvell.com>,
+ Yehuda Yitschak <yehuday at marvell.com>,
+ linux-arm-kernel at lists.infradead.org, Antoine Tenart
+ <antoine.tenart at free-electrons.com>, =?utf-8?q?Miqu=C3=A8l_Raynal?=
+ <miquel.raynal at free-electrons.com>, Victor Gu <xigu at marvell.com>,
+ Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+Date: Thu, 28 Sep 2017 14:58:36 +0200
+From: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+List-Id: <linux-pci.vger.kernel.org>
+
+From: Victor Gu <xigu at marvell.com>
+
+Some PCIe devices do not support LOS, and will cause timeouts if the
+root complex forces the LOS state. This patch disables the LOS state
+by default.
+
+This is part of fixing bug
+https://bugzilla.kernel.org/show_bug.cgi?id=196339, this commit was
+reported as the user to be important to get a Intel 7260 mini-PCIe
+WiFi card working.
+
+Fixes: 8c39d710363c1 ("PCI: aardvark: Add Aardvark PCI host controller driver")
+Signed-off-by: Victor Gu <xigu at marvell.com>
+Reviewed-by: Evan Wang <xswang at marvell.com>
+Reviewed-by: Nadav Haklai <nadavh at marvell.com>
+[Thomas: tweak commit log.]
+Signed-off-by: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+---
+ drivers/pci/host/pci-aardvark.c | 3 +--
+ 1 file changed, 1 insertion(+), 2 deletions(-)
+
+--- a/drivers/pci/host/pci-aardvark.c
++++ b/drivers/pci/host/pci-aardvark.c
+@@ -368,8 +368,7 @@ static void advk_pcie_setup_hw(struct ad
+
+ advk_pcie_wait_for_link(pcie);
+
+- reg = PCIE_CORE_LINK_L0S_ENTRY |
+- (1 << PCIE_CORE_LINK_WIDTH_SHIFT);
++ reg = (1 << PCIE_CORE_LINK_WIDTH_SHIFT);
+ advk_writel(pcie, reg, PCIE_CORE_LINK_CTRL_STAT_REG);
+
+ reg = advk_readl(pcie, PCIE_CORE_CMD_STATUS_REG);
diff --git a/target/linux/mvebu/patches-4.14/527-PCI-aardvark-fix-PCIe-max-read-request-size-setting.patch b/target/linux/mvebu/patches-4.14/527-PCI-aardvark-fix-PCIe-max-read-request-size-setting.patch
new file mode 100644
index 0000000000..eaf7b097b0
--- /dev/null
+++ b/target/linux/mvebu/patches-4.14/527-PCI-aardvark-fix-PCIe-max-read-request-size-setting.patch
@@ -0,0 +1,63 @@
+From patchwork Thu Sep 28 12:58:37 2017
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v2,6/7] PCI: aardvark: fix PCIe max read request size setting
+X-Patchwork-Submitter: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+X-Patchwork-Id: 819591
+Message-Id: <20170928125838.11887-7-thomas.petazzoni at free-electrons.com>
+To: Bjorn Helgaas <bhelgaas at google.com>, linux-pci at vger.kernel.org
+Cc: Jason Cooper <jason at lakedaemon.net>, Andrew Lunn <andrew at lunn.ch>,
+ Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>, Gregory Clement
+ <gregory.clement at free-electrons.com>,
+ Nadav Haklai <nadavh at marvell.com>, Hanna Hawa <hannah at marvell.com>,
+ Yehuda Yitschak <yehuday at marvell.com>,
+ linux-arm-kernel at lists.infradead.org, Antoine Tenart
+ <antoine.tenart at free-electrons.com>, =?utf-8?q?Miqu=C3=A8l_Raynal?=
+ <miquel.raynal at free-electrons.com>, Evan Wang <xswang at marvell.com>,
+ Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+Date: Thu, 28 Sep 2017 14:58:37 +0200
+From: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+List-Id: <linux-pci.vger.kernel.org>
+
+From: Evan Wang <xswang at marvell.com>
+
+There is an obvious typo issue in the definition of the PCIe maximum
+read request size: a bit shift is directly used as a value, while it
+should be used to shift the correct value.
+
+This is part of fixing bug
+https://bugzilla.kernel.org/show_bug.cgi?id=196339, this commit was
+reported as the user to be important to get a Intel 7260 mini-PCIe
+WiFi card working.
+
+Fixes: 8c39d710363c1 ("PCI: aardvark: Add Aardvark PCI host controller driver")
+Signed-off-by: Evan Wang <xswang at marvell.com>
+Reviewed-by: Victor Gu <xigu at marvell.com>
+Reviewed-by: Nadav Haklai <nadavh at marvell.com>
+[Thomas: tweak commit log.]
+Signed-off-by: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+---
+ drivers/pci/host/pci-aardvark.c | 4 +++-
+ 1 file changed, 3 insertions(+), 1 deletion(-)
+
+--- a/drivers/pci/host/pci-aardvark.c
++++ b/drivers/pci/host/pci-aardvark.c
+@@ -33,6 +33,7 @@
+ #define PCIE_CORE_DEV_CTRL_STATS_MAX_PAYLOAD_SZ 0x2
+ #define PCIE_CORE_DEV_CTRL_STATS_SNOOP_DISABLE (0 << 11)
+ #define PCIE_CORE_DEV_CTRL_STATS_MAX_RD_REQ_SIZE_SHIFT 12
++#define PCIE_CORE_DEV_CTRL_STATS_MAX_RD_REQ_SZ 0x2
+ #define PCIE_CORE_MPS_UNIT_BYTE 128
+ #define PCIE_CORE_LINK_CTRL_STAT_REG 0xd0
+ #define PCIE_CORE_LINK_L0S_ENTRY BIT(0)
+@@ -303,7 +304,8 @@ static void advk_pcie_setup_hw(struct ad
+ (PCIE_CORE_DEV_CTRL_STATS_MAX_PAYLOAD_SZ <<
+ PCIE_CORE_DEV_CTRL_STATS_MAX_PAYLOAD_SZ_SHIFT) |
+ PCIE_CORE_DEV_CTRL_STATS_SNOOP_DISABLE |
+- PCIE_CORE_DEV_CTRL_STATS_MAX_RD_REQ_SIZE_SHIFT;
++ (PCIE_CORE_DEV_CTRL_STATS_MAX_RD_REQ_SZ <<
++ PCIE_CORE_DEV_CTRL_STATS_MAX_RD_REQ_SIZE_SHIFT);
+ advk_writel(pcie, reg, PCIE_CORE_DEV_CTRL_STATS_REG);
+
+ /* Program PCIe Control 2 to disable strict ordering */
--
2.16.2
More information about the Lede-dev
mailing list