[LEDE-DEV] [PATCH] ramips: Add support for ZBT WE1026-5G
Kristian Evensen
kristian.evensen at gmail.com
Sun Sep 10 05:44:47 PDT 2017
The ZBT WE1026-5G
(http://www.zbtlink.com/products/router/WE1026-5G.html) is the follow-up
to the ZBT WE1026 and is based on MT7620. For the previous WE1026, the
ZBT WE826 image could be used. However, as the name implies, the -5G
comes equipped with a 5GHz wifi radio. As the WE826 only has a 2.4GHz
radio, the addition of 5GHz means that a separate image is needed for
the WE1026-5G. I suspect that this image will also work on the previous
WE1026, but I don't have a device to test with.
The WE1026-5G has following specifications:
* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x 5GHz wifi (MT7612)
* 1x button.
* 3x controllable LEDs.
Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).
Not working:
* The 5GHz WIFI LED is completely dead. I suspect the issue is the same
as on other devices with Mediatek 5Ghz wifi-cards/chips. The LED is
controlled by the driver, and mt76 (currently) does not support this.
Not tested:
* SD card reader.
Notes:
* The modem (labeled 3G/4G) and power LEDs are controlled by the
hardware.
* There is a 32MB version of this device available, but I do not have
access to it. I have therefor only added support for the 16MB version,
but added all the required infrastructure to make adding support for the
32MB version easy.
Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.
Recovery:
If you brick the device, the WE1026-5G supports recovery using HTTP. Keep the
reset button pressed for ~5sec when booting to start the web server. Set the
address of the network interface on your machine to 192.168.1.2/24, and
point your browser to 192.168.1.1 to access the recovery UI. From the
recovery UI you can upload a firmware image.
Signed-off-by: Kristian Evensen <kristian.evensen at gmail.com>
---
target/linux/ramips/base-files/etc/board.d/01_leds | 5 +
.../linux/ramips/base-files/etc/board.d/02_network | 3 +-
target/linux/ramips/base-files/lib/ramips.sh | 3 +
.../ramips/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ramips/dts/WE1026-5G-16M.dts | 76 +++++++++++++
target/linux/ramips/dts/WE1026-5G.dtsi | 124 +++++++++++++++++++++
target/linux/ramips/image/mt7620.mk | 9 ++
7 files changed, 220 insertions(+), 1 deletion(-)
create mode 100644 target/linux/ramips/dts/WE1026-5G-16M.dts
create mode 100644 target/linux/ramips/dts/WE1026-5G.dtsi
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 83e1a94000..f6a7bac81a 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -379,6 +379,11 @@ w502u)
wcr-150gn)
set_usb_led "$board:amber:user"
;;
+we1026-5g-16m)
+ ucidef_set_led_netdev "lan" "LAN" "we1026-5g:green:lan" "eth0"
+ set_wifi_led "we1026-5g:green:wifi"
+ set_usb_led "we1026-5g:green:usb" "1-1.1"
+ ;;
whr-1166d|\
whr-300hp2|\
whr-600d)
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 9284b1812f..6f05259467 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -323,7 +323,8 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"3:lan" "4:wan" "6 at eth0"
;;
- wcr-150gn)
+ wcr-150gn|\
+ we1026-5g-16m)
ucidef_add_switch "switch0" \
"0:lan" "6t at eth0"
;;
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 174e29e434..d0055d422b 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -553,6 +553,9 @@ ramips_board_detect() {
*"WCR-150GN")
name="wcr-150gn"
;;
+ *"WE1026-5G (16M)")
+ name="we1026-5g-16m"
+ ;;
*"WF-2881")
name="wf-2881"
;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 5cfca52ab1..09a7dae394 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -193,6 +193,7 @@ platform_check_image() {
x8|\
y1|\
y1s|\
+ we1026-5g-16m|\
zbt-ape522ii|\
zbt-cpe102|\
zbt-wa05|\
diff --git a/target/linux/ramips/dts/WE1026-5G-16M.dts b/target/linux/ramips/dts/WE1026-5G-16M.dts
new file mode 100644
index 0000000000..e01e86423c
--- /dev/null
+++ b/target/linux/ramips/dts/WE1026-5G-16M.dts
@@ -0,0 +1,76 @@
+/*
+ * BSD LICENSE
+ *
+ * Copyright(c) 2017 Kristian Evensen <kristian.evensen at gmail.com>.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name of Broadcom Corporation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+#include "WE1026-5G.dtsi"
+
+/ {
+ compatible = "zbtlink,we1026-5g-16m", "ralink,mt7620a-soc";
+ model = "ZBT WE1026-5G (16M)";
+};
+
+&spi0 {
+ status = "okay";
+
+ en25q128 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ firmware: partition at 50000 {
+ label = "firmware";
+ reg = <0x50000 0xfb0000>;
+ };
+ };
+};
diff --git a/target/linux/ramips/dts/WE1026-5G.dtsi b/target/linux/ramips/dts/WE1026-5G.dtsi
new file mode 100644
index 0000000000..c357e1eee7
--- /dev/null
+++ b/target/linux/ramips/dts/WE1026-5G.dtsi
@@ -0,0 +1,124 @@
+/*
+ * BSD LICENSE
+ *
+ * Copyright(c) 2017 Kristian Evensen <kristian.evensen at gmail.com>.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name of Broadcom Corporation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include "mt7620a.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "zbtlink,we1026-5g", "ralink,mt7620a-soc";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ lan {
+ label = "we1026-5g:green:lan";
+ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+ };
+
+ usb {
+ label = "we1026-5g:green:usb";
+ gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ wifi {
+ label = "we1026-5g:green:wifi";
+ gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+ reset {
+ label = "reset";
+ gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&gpio2 {
+ status = "okay";
+};
+
+&gpio3 {
+ status = "okay";
+};
+
+&sdhci {
+ status = "okay";
+};
+
+&ehci {
+ status = "okay";
+};
+
+&ohci {
+ status = "okay";
+};
+
+ðernet {
+ mtd-mac-address = <&factory 0x28>;
+};
+
+&wmac {
+ ralink,mtd-eeprom = <&factory 0>;
+};
+
+&pinctrl {
+ state_default: pinctrl0 {
+ default {
+ ralink,group = "i2c", "uartf", "spi refclk", "ephy", "wled";
+ ralink,function = "gpio";
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+ pcie-bridge {
+ wifi at 14c3,7662 {
+ compatible = "pci14c3,7662";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ };
+ };
+};
diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk
index f201c9d404..6d2533d349 100644
--- a/target/linux/ramips/image/mt7620.mk
+++ b/target/linux/ramips/image/mt7620.mk
@@ -480,6 +480,15 @@ define Device/youku-yk1
endef
TARGET_DEVICES += youku-yk1
+define Device/we1026-5g-16m
+ DTS := WE1026-5G-16M
+ IMAGE_SIZE := 16777216
+ SUPPORTED_DEVICES += we1026-5g-16m
+ DEVICE_TITLE := Zbtlink ZBT-WE1026-5G (16M)
+ DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-mt76 kmod-sdhci-mt7620
+endef
+TARGET_DEVICES += we1026-5g-16m
+
define Device/zbt-ape522ii
DTS := ZBT-APE522II
DEVICE_TITLE := Zbtlink ZBT-APE522II
--
2.11.0
More information about the Lede-dev
mailing list