[LEDE-DEV] QCA Dakota support

[Matthew McClintock]

Can you share a full log? What is the flash_type from smem? Is this a
nand or nor booting board? I suggest using initramfs first until you
get things going.

-M

On Thu, Mar 9, 2017 at 7:11 AM, K.Mani <sailormani at gmail.com> wrote:
> Hi Matthew,
>
> I built the qsdk, but the device flash failed & bricked.
> and i get the u-boot prompt only.
> Can you suggest me the flashing procedure for ipq40xx?
>
> https://source.codeaurora.org/quic/qsdk/releases/manifest/qstak/tree/?h=release
> --    caf_AU_LINUX_QSDK_RELEASE_DAKOTA_CS_TARGET_ALL.3.0.1011.220.xml
>
> flashing ipq40xx:
>              flashed NOR Boot --- hlos & rootfs partition
>
> smeminfo:
> partition table offset  0x0
> No.: Name             Attributes            Start             Size
>   0: 0:SBL1           0x0000ffff              0x0          0x40000
>   1: 0:MIBIB          0x001040ff          0x40000          0x20000
>   2: 0:QSEE           0x0000ffff          0x60000          0x60000
>   3: 0:CDT            0x0000ffff          0xc0000          0x10000
>   4: 0:DDRPARAMS      0x0000ffff          0xd0000          0x10000
>   5: 0:APPSBLENV      0x0000ffff          0xe0000          0x10000
>   6: 0:APPSBL         0x0000ffff          0xf0000          0x80000
>   7: 0:ART            0x0000ffff         0x170000          0x10000
>   8: 0:HLOS           0x0000ffff         0x180000         0x400000
>   9: rootfs           0x0000ffff         0x580000         0xa80000
>
>
> Thanks again
> Mani
>
> On Thu, Mar 9, 2017 at 12:32 PM, John Crispin <john at phrozen.org> wrote:
>> Hi Matthew,
>>
>> can you point me at the tree to use on codeaurora ? i am also looking for
>> the AP145 dts file. this is ipq8062 based
>>
>>     John
>>
>>
>>
>> On 08/03/17 15:49, Matthew McClintock wrote:
>>>
>>> Most of the support for the SoC should be in place, the various Dakota
>>> boards dk0{1,4,7}-c{1,2,3,4} are very similar. You could look at the
>>> device tree's on codeaurora.org to compare the differences from a
>>> supported platform and this variant.
>>>
>>> -M
>>>
>>> On Wed, Mar 8, 2017 at 2:47 AM, K.Mani <sailormani at gmail.com> wrote:
>>>>
>>>> I have a target board based on IPQ40xx, I want to port LEDE on it.
>>>> Does LEDE has support for the following type:
>>>>
>>>> Model: Qualcomm Technologies, Inc. IPQ40xx/AP-DK04.1-C2
>>>> Compatible: qcom,ipq40xx-apdk04.1qcom,ipq40xx
>>>> SF: MX25L25635E
>>>>
>>>> Thanks
>>>> Mani
>>>>
>>>> _______________________________________________
>>>> Lede-dev mailing list
>>>> Lede-dev at lists.infradead.org
>>>> http://lists.infradead.org/mailman/listinfo/lede-dev
>>>
>>> _______________________________________________
>>> Lede-dev mailing list
>>> Lede-dev at lists.infradead.org
>>> http://lists.infradead.org/mailman/listinfo/lede-dev
>>
>>