The WMDR-143N is a small module originally used as a Wifi client
in some Loewe smart TV sets. It is sold cheaply at german surplus
shops. The module contains a RT3662 SOC.
Specifications:
- 500 MHz CPU Clock
- 1x 10/100Mbps Ethernet (pin header)
- 32 MB of RAM
- 8 MB of FLASH
- 2T3R 2.4/5 GHz (SOC internal)
- 3 Antennas on PCB
- UART pads on PCB (J3: 1 = +3.3V, 2 = RX, 3 = TX, 4 = GND), TX
and RX are 3,3V only! The square hole is pin 1
- Power supply pads on PCB (J6: 1 and 2 = +5V, 3 and 4 = GND)
The square hole is pin 1
The original firmware has two identical kernel/rootfs images and
two "Factory" calibration data blocks in flash. The LEDE image
leaves only the first "Factory" block in place and uses both
"Kernel" blocks and the redundant "Factory" block together to gain
enough space for the jffs2 partition.
Flash instructions:
You need UART and Ethernet connections to flash the board. Use
the LEDE "sysupgrade.bin" image with tftp.
Apply power to the board and in the first 5 seconds, hit 2 to
select TFTP upload. The bootloader asks for board- and server IP
addresses and filename.
Alternate method: With the vendor firmware running, assign an IP
address to the ethernet port, tftp the firmware image to
/tmp and write to mtd4 ("KernelA").
Signed-off-by: Oliver Fleischmann <ogf at bnv-bamberg.de>
---
.../linux/ramips/base-files/etc/board.d/02_network | 4 +-
target/linux/ramips/base-files/lib/ramips.sh | 3 +
.../ramips/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ramips/dts/WMDR-143N.dts | 73 ++++++++++++++++++++++
target/linux/ramips/image/rt3883.mk | 8 +++
5 files changed, 88 insertions(+), 1 deletion(-)
create mode 100644 target/linux/ramips/dts/WMDR-143N.dts
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 78ba10342b..fce754e295 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -222,6 +222,7 @@ ramips_setup_interfaces()
na930|\
pbr-d1|\
wli-tx4-ag300n|\
+ wmdr-143n|\
wmr-300|\
wn3000rpv3|\
wrh-300cr)
@@ -333,7 +334,8 @@ ramips_setup_macs()
case $board in
a5-v11|\
- ht-tm02)
+ ht-tm02|\
+ wmdr-143n)
lan_mac=$(cat /sys/class/net/eth0/address)
;;
all0239-3g|\
diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 056fab9def..9b02d98ce2 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -589,6 +589,9 @@ ramips_board_detect() {
*"WLR-6000")
name="wlr-6000"
;;
+ *"WMDR-143N")
+ name="wmdr-143n"
+ ;;
*"WMR-300")
name="wmr-300"
;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index e0a260216d..2a2625ca89 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -168,6 +168,7 @@ platform_check_image() {
wl-wn575a3|\
wli-tx4-ag300n|\
wlr-6000|\
+ wmdr-143n|\
wmr-300|\
wn3000rpv3|\
wnce2001|\
diff --git a/target/linux/ramips/dts/WMDR-143N.dts b/target/linux/ramips/dts/WMDR-143N.dts
new file mode 100644
index 0000000000..291f46f856
--- /dev/null
+++ b/target/linux/ramips/dts/WMDR-143N.dts
@@ -0,0 +1,73 @@
+/dts-v1/;
+
+#include "rt3883.dtsi"
+
+/ {
+ compatible = "loewe,wmdr-143n", "ralink,rt3883-soc";
+ model = "Loewe WMDR-143N";
+};
+
+&spi0 {
+ status = "okay";
+
+ m25p80 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x00010000>;
+ read-only;
+ };
+
+ factory: partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ label = "firmware";
+ reg = <0x50000 0x7b0000>;
+ };
+ };
+};
+
+&pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "i2c", "jtag", "uartf";
+ ralink,function = "gpio";
+ };
+ };
+};
+
+ðernet {
+ port at 0 {
+ phy-handle = <&phy0>;
+ phy-mode = "mii";
+ };
+ mdio-bus {
+ status = "okay";
+
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ phy-mode = "mii";
+ };
+ };
+};
+
+&wmac {
+ status = "okay";
+ ralink,mtd-eeprom = <&factory 0>;
+ mtd-mac-address = <&factory 0x4>;
+};
diff --git a/target/linux/ramips/image/rt3883.mk b/target/linux/ramips/image/rt3883.mk
index 2cd60f3858..f90fc6154f 100644
--- a/target/linux/ramips/image/rt3883.mk
+++ b/target/linux/ramips/image/rt3883.mk
@@ -114,3 +114,11 @@ define Device/wlr-6000
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 swconfig
endef
TARGET_DEVICES += wlr-6000
+
+
+define Device/wmdr-143n
+ DTS := WMDR-143N
+ BLOCKSIZE := 64k
+ DEVICE_TITLE := Loewe WMDR-143N
+endef
+TARGET_DEVICES += wmdr-143n
--
2.13.0