[LEDE-DEV] Mikrotik sysupgrade install not working on sxt lite2.
Denis Periša
darkman.hr at gmail.com
Sun Feb 26 09:46:39 PST 2017
I dont see issues in boot log? I had problem with sysupgrade on rb435g
with kernel partition nand had bad sectors so kernel was too big. it
rebooted without warning and I was left in net boot.. and since make
kernel_menuconfig is not working I cannot shrink it. If anyone have
suggestion... or fix to enable some check if the firmware was updated
good or not without rebooting it.
tnx
On Sun, Feb 26, 2017 at 6:20 PM, Alen Opacic <subixonfire at gmail.com> wrote:
> log from initramfs while routeros on nand:
> root at LEDE:~# dmesg
> [ 0.000000] Linux version 4.4.50
> (buildbot at builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE
> GCC 5.4.0 r3103-1b51a49) ) #0 Mon Feb 20 17:13:44 2017
> [ 0.000000] bootconsole [early0] enabled
> [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
> [ 0.000000] SoC: Atheros AR9344 rev 3
> [ 0.000000] Determined physical RAM map:
> [ 0.000000] memory: 04000000 @ 00000000 (usable)
> [ 0.000000] User-defined physical RAM map:
> [ 0.000000] memory: 04000000 @ 00000000 (usable)
> [ 0.000000] Initrd not found or empty - disabling initrd
> [ 0.000000] No valid device tree found, continuing without
> [ 0.000000] Zone ranges:
> [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
> [ 0.000000] Movable zone start for each node
> [ 0.000000] Early memory node ranges
> [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
> [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
> [ 0.000000] On node 0 totalpages: 16384
> [ 0.000000] free_area_init_node: node 0, pgdat 8042e4d0,
> node_mem_map 81000000
> [ 0.000000] Normal zone: 128 pages used for memmap
> [ 0.000000] Normal zone: 0 pages reserved
> [ 0.000000] Normal zone: 16384 pages, LIFO batch:3
> [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
> [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
> linesize 32 bytes
> [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
> [ 0.000000] pcpu-alloc: [0] 0
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
> Total pages: 16256
> [ 0.000000] Kernel command line: parts=1 boot_part_size=4194304
> gpio=228923 HZ=300000000 mem=64M kmac=4C:5E:0C:DD:A5:54 board=sxt5n
> boot=0 mlc=7 rootfstype=squashfs noinitrd
> [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
> [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
> [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
> [ 0.000000] Writing ErrCtl register=00000000
> [ 0.000000] Readback ErrCtl register=00000000
> [ 0.000000] Memory: 57988K/65536K available (3394K kernel code,
> 174K rwdata, 468K rodata, 2292K init, 203K bss, 7548K reserved, 0K
> cma-reserved)
> [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> [ 0.000000] NR_IRQS:51
> [ 0.000000] Clocks: CPU:600.000MHz, DDR:400.000MHz, AHB:400.000MHz,
> Ref:25.000MHz
> [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles:
> 0xffffffff, max_idle_ns: 6370868154 ns
> [ 0.000009] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps
> every 7158278654ns
> [ 0.008859] Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
> [ 0.081947] pid_max: default: 32768 minimum: 301
> [ 0.087321] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.094846] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.105537] clocksource: jiffies: mask: 0xffffffff max_cycles:
> 0xffffffff, max_idle_ns: 19112604462750000 ns
> [ 0.117936] NET: Registered protocol family 16
> [ 0.124541] MIPS: machine is Mikrotik RouterBOARD SXT Lite5
> [ 0.361624] clocksource: Switched to clocksource MIPS
> [ 0.368540] NET: Registered protocol family 2
> [ 0.374515] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.382497] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.389718] TCP: Hash tables configured (established 1024 bind 1024)
> [ 0.397039] UDP hash table entries: 256 (order: 0, 4096 bytes)
> [ 0.403721] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> [ 0.411130] NET: Registered protocol family 1
> [ 0.416150] PCI: CLS 0 bytes, default 32
> [ 3.059448] futex hash table entries: 256 (order: -1, 3072 bytes)
> [ 3.066513] Crashlog allocated RAM at address 0x3f00000
> [ 3.087978] squashfs: version 4.0 (2009/01/31) Phillip Lougher
> [ 3.094653] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
> (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
> [ 3.108704] io scheduler noop registered
> [ 3.113217] io scheduler deadline registered (default)
> [ 3.119339] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
> [ 3.129464] console [ttyS0] disabled
> [ 3.153707] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11,
> base_baud = 1562500) is a 16550A
> [ 3.163506] console [ttyS0] enabled
> [ 3.246999] bootconsole [early0] disabled
> [ 3.348877] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xf1
> [ 3.425110] nand: Toshiba NAND 128MiB 3,3V 8-bit
> [ 3.480472] nand: 128 MiB, SLC, erase size: 128 KiB, page size:
> 2048, OOB size: 64
> [ 3.571393] Scanning device for bad blocks
> [ 3.727044] Bad eraseblock 768 at 0x000006000000
> [ 3.817732] Creating 3 MTD partitions on "ar934x-nfc":
> [ 3.879403] 0x000000000000-0x000000040000 : "booter"
> [ 3.940552] 0x000000040000-0x000000400000 : "kernel"
> [ 4.002003] 0x000000400000-0x000008000000 : "ubi"
> [ 4.078242] libphy: ag71xx_mdio: probed
> [ 4.713381] ag71xx-mdio.1: Found an AR934X built-in switch
> [ 4.815812] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
> [ 4.890329] NET: Registered protocol family 10
> [ 4.948470] NET: Registered protocol family 17
> [ 5.001898] bridge: automatic filtering via arp/ip/ip6tables has
> been deprecated. Update your scripts to load br_netfilter if you need
> this.
> [ 5.153388] 8021q: 802.1Q VLAN Support v1.8
> [ 5.207548] UBI error: no valid UBI magic found inside mtd2
> [ 5.287623] Freeing unused kernel memory: 2292K (80453000 - 80690000)
> [ 5.381163] init: Console is alive
> [ 5.422276] init: - watchdog -
> [ 5.480010] init: - preinit -
> [ 5.716917] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> [ 5.808548] random: procd: uninitialized urandom read (4 bytes
> read, 71 bits of entropy available)
> [ 7.412870] eth0: link up (1000Mbps/Full duplex)
> [ 7.468325] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> [ 9.048069] eth0: link down
> [ 9.093218] procd: - early -
> [ 9.127952] procd: - watchdog -
> [ 9.723266] procd: - ubus -
> [ 9.764582] random: ubusd: uninitialized urandom read (4 bytes
> read, 77 bits of entropy available)
> [ 9.874143] random: ubusd: uninitialized urandom read (4 bytes
> read, 77 bits of entropy available)
> [ 9.982299] random: ubusd: uninitialized urandom read (4 bytes
> read, 77 bits of entropy available)
> [ 10.090048] random: ubusd: uninitialized urandom read (4 bytes
> read, 77 bits of entropy available)
> [ 10.197943] random: ubusd: uninitialized urandom read (4 bytes
> read, 77 bits of entropy available)
> [ 10.305638] random: ubusd: uninitialized urandom read (4 bytes
> read, 77 bits of entropy available)
> [ 10.413459] random: ubusd: uninitialized urandom read (4 bytes
> read, 78 bits of entropy available)
> [ 10.521340] random: ubusd: uninitialized urandom read (4 bytes
> read, 78 bits of entropy available)
> [ 10.629430] procd: - init -
> [ 10.833748] ip6_tables: (C) 2000-2006 Netfilter Core Team
> [ 10.909722] Loading modules backported from Linux version
> wt-2016-10-03-1-g6fcb1a6
> [ 11.000647] Backport generated by backports.git backports-20160324-9-g0e38f5c
> [ 11.089492] ip_tables: (C) 2000-2006 Netfilter Core Team
> [ 11.161967] nf_conntrack version 0.5.0 (941 buckets, 3764 max)
> [ 11.270519] xt_time: kernel timezone is -0000
> [ 11.385821] PPP generic driver version 2.4.2
> [ 11.439758] NET: Registered protocol family 24
> [ 11.541226] ath: EEPROM regdomain: 0x0
> [ 11.541248] ath: EEPROM indicates default country code should be used
> [ 11.541257] ath: doing EEPROM country->regdmn map search
> [ 11.541279] ath: country maps to regdmn code: 0x3a
> [ 11.541290] ath: Country alpha2 being used: US
> [ 11.541299] ath: Regpair used: 0x3a
> [ 11.554767] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
> [ 11.560747] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
> [ 12.018618] random: jshn: uninitialized urandom read (4 bytes read,
> 79 bits of entropy available)
> [ 19.078173] device eth0 entered promiscuous mode
> [ 19.252891] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
> [ 20.672910] eth0: link up (1000Mbps/Full duplex)
> [ 20.791686] br-lan: port 1(eth0) entered forwarding state
> [ 20.856490] br-lan: port 1(eth0) entered forwarding state
> [ 21.051685] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
> [ 22.851637] br-lan: port 1(eth0) entered forwarding state
>
>
> log frmo initramfs after sysupgrade:
> root at LEDE:~# dmesg
> [ 0.000000] Linux version 4.4.50
> (buildbot at builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE
> GCC 5.4.0 r3103-1b51a49) ) #0 Mon Feb 20 17:13:44 2017
> [ 0.000000] bootconsole [early0] enabled
> [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
> [ 0.000000] SoC: Atheros AR9344 rev 3
> [ 0.000000] Determined physical RAM map:
> [ 0.000000] memory: 04000000 @ 00000000 (usable)
> [ 0.000000] User-defined physical RAM map:
> [ 0.000000] memory: 04000000 @ 00000000 (usable)
> [ 0.000000] Initrd not found or empty - disabling initrd
> [ 0.000000] No valid device tree found, continuing without
> [ 0.000000] Zone ranges:
> [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
> [ 0.000000] Movable zone start for each node
> [ 0.000000] Early memory node ranges
> [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
> [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
> [ 0.000000] On node 0 totalpages: 16384
> [ 0.000000] free_area_init_node: node 0, pgdat 8042e4d0,
> node_mem_map 81000000
> [ 0.000000] Normal zone: 128 pages used for memmap
> [ 0.000000] Normal zone: 0 pages reserved
> [ 0.000000] Normal zone: 16384 pages, LIFO batch:3
> [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
> [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
> linesize 32 bytes
> [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
> [ 0.000000] pcpu-alloc: [0] 0
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
> Total pages: 16256
> [ 0.000000] Kernel command line: parts=1 boot_part_size=4194304
> gpio=261675 HZ=300000000 mem=64M kmac=4C:5E:0C:DD:A5:54 board=sxt5n
> ver=3.22 hw_opt=00200001 boot=1 mlc=8 rootfstype=squashfs noinitrd
> [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
> [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
> [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
> [ 0.000000] Writing ErrCtl register=00000000
> [ 0.000000] Readback ErrCtl register=00000000
> [ 0.000000] Memory: 57988K/65536K available (3394K kernel code,
> 174K rwdata, 468K rodata, 2292K init, 203K bss, 7548K reserved, 0K
> cma-reserved)
> [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> [ 0.000000] NR_IRQS:51
> [ 0.000000] Clocks: CPU:600.000MHz, DDR:400.000MHz, AHB:400.000MHz,
> Ref:25.000MHz
> [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles:
> 0xffffffff, max_idle_ns: 6370868154 ns
> [ 0.000009] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps
> every 7158278654ns
> [ 0.008860] Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
> [ 0.081947] pid_max: default: 32768 minimum: 301
> [ 0.087321] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.094846] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.105579] clocksource: jiffies: mask: 0xffffffff max_cycles:
> 0xffffffff, max_idle_ns: 19112604462750000 ns
> [ 0.117974] NET: Registered protocol family 16
> [ 0.124605] MIPS: machine is Mikrotik RouterBOARD SXT Lite5
> [ 0.361771] clocksource: Switched to clocksource MIPS
> [ 0.368684] NET: Registered protocol family 2
> [ 0.374660] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.382649] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.389870] TCP: Hash tables configured (established 1024 bind 1024)
> [ 0.397191] UDP hash table entries: 256 (order: 0, 4096 bytes)
> [ 0.403874] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> [ 0.411283] NET: Registered protocol family 1
> [ 0.416311] PCI: CLS 0 bytes, default 32
> [ 3.060957] futex hash table entries: 256 (order: -1, 3072 bytes)
> [ 3.068028] Crashlog allocated RAM at address 0x3f00000
> [ 3.089507] squashfs: version 4.0 (2009/01/31) Phillip Lougher
> [ 3.096185] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
> (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
> [ 3.110259] io scheduler noop registered
> [ 3.114767] io scheduler deadline registered (default)
> [ 3.120890] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
> [ 3.131017] console [ttyS0] disabled
> [ 3.155264] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11,
> base_baud = 1562500) is a 16550A
> [ 3.165065] console [ttyS0] enabled
> [ 3.248553] bootconsole [early0] disabled
> [ 3.350438] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xf1
> [ 3.426664] nand: Toshiba NAND 128MiB 3,3V 8-bit
> [ 3.482025] nand: 128 MiB, SLC, erase size: 128 KiB, page size:
> 2048, OOB size: 64
> [ 3.572940] Scanning device for bad blocks
> [ 3.728580] Bad eraseblock 768 at 0x000006000000
> [ 3.819237] Creating 3 MTD partitions on "ar934x-nfc":
> [ 3.880853] 0x000000000000-0x000000040000 : "booter"
> [ 3.942066] 0x000000040000-0x000000400000 : "kernel"
> [ 4.003494] 0x000000400000-0x000008000000 : "ubi"
> [ 4.079865] libphy: ag71xx_mdio: probed
> [ 4.713528] ag71xx-mdio.1: Found an AR934X built-in switch
> [ 4.815955] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
> [ 4.890531] NET: Registered protocol family 10
> [ 4.948671] NET: Registered protocol family 17
> [ 5.002095] bridge: automatic filtering via arp/ip/ip6tables has
> been deprecated. Update your scripts to load br_netfilter if you need
> this.
> [ 5.153583] 8021q: 802.1Q VLAN Support v1.8
> [ 5.207734] UBI: auto-attach mtd2
> [ 5.245407] ubi0: attaching mtd2
> [ 5.891298] random: nonblocking pool is initialized
> [ 6.975271] ubi0: scanning is finished
> [ 7.039354] ubi0: attached mtd2 (name "ubi", size 124 MiB)
> [ 7.105208] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
> [ 7.187682] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
> [ 7.268108] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
> [ 7.349580] ubi0: good PEBs: 991, bad PEBs: 1, corrupted PEBs: 0
> [ 7.421668] ubi0: user volume: 3, internal volumes: 1, max. volumes
> count: 128
> [ 7.508360] ubi0: max/mean erase counter: 1/0, WL threshold: 4096,
> image sequence number: 1976066036
> [ 7.617998] ubi0: available PEBs: 0, total reserved PEBs: 991, PEBs
> reserved for bad PEB handling: 19
> [ 7.728736] ubi0: background thread "ubi_bgt0d" started, PID 302
> [ 7.802978] block ubiblock0_1: created from ubi0:1(rootfs)
> [ 7.868834] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
> [ 7.968092] Freeing unused kernel memory: 2292K (80453000 - 80690000)
> [ 8.059771] init: Console is alive
> [ 8.100901] init: - watchdog -
> [ 8.158582] init: - preinit -
> [ 8.387088] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> [ 9.983020] eth0: link up (1000Mbps/Full duplex)
> [ 10.038568] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> [ 11.615684] eth0: link down
> [ 11.660217] procd: - early -
> [ 11.695544] procd: - watchdog -
> [ 12.298030] procd: - ubus -
> [ 12.384225] procd: - init -
> [ 12.588293] ip6_tables: (C) 2000-2006 Netfilter Core Team
> [ 12.664281] Loading modules backported from Linux version
> wt-2016-10-03-1-g6fcb1a6
> [ 12.755187] Backport generated by backports.git backports-20160324-9-g0e38f5c
> [ 12.844109] ip_tables: (C) 2000-2006 Netfilter Core Team
> [ 12.916425] nf_conntrack version 0.5.0 (941 buckets, 3764 max)
> [ 13.025079] xt_time: kernel timezone is -0000
> [ 13.138101] PPP generic driver version 2.4.2
> [ 13.192061] NET: Registered protocol family 24
> [ 13.293835] ath: EEPROM regdomain: 0x0
> [ 13.293857] ath: EEPROM indicates default country code should be used
> [ 13.293867] ath: doing EEPROM country->regdmn map search
> [ 13.293888] ath: country maps to regdmn code: 0x3a
> [ 13.293899] ath: Country alpha2 being used: US
> [ 13.293908] ath: Regpair used: 0x3a
> [ 13.307324] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
> [ 13.313386] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
> [ 20.778235] device eth0 entered promiscuous mode
> [ 20.953094] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
> [ 22.373025] eth0: link up (1000Mbps/Full duplex)
> [ 22.491841] br-lan: port 1(eth0) entered forwarding state
> [ 22.556693] br-lan: port 1(eth0) entered forwarding state
> [ 22.751859] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
> [ 24.551849] br-lan: port 1(eth0) entered forwarding state
>
>
>
> 2017-02-23 20:46 GMT+01:00 Alen Opacic <subixonfire at gmail.com>:
>> Sxt LIte2(sxt2ndr2) boot log:
>>
>> [ 0.000000] Linux version 4.4.49 (buildbot at builds) (gcc version
>> 5.4.0 (LEDE GCC 5.4.0 r3511-04c4b6f) ) #0 Mon Feb 20 09:21:42 2017
>> [ 0.000000] bootconsole [early0] enabled
>> [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
>> [ 0.000000] SoC: Atheros AR9344 rev 3
>> [ 0.000000] Determined physical RAM map:
>> [ 0.000000] memory: 04000000 @ 00000000 (usable)
>> [ 0.000000] User-defined physical RAM map:
>> [ 0.000000] memory: 04000000 @ 00000000 (usable)
>> [ 0.000000] Initrd not found or empty - disabling initrd
>> [ 0.000000] No valid device tree found, continuing without
>> [ 0.000000] Zone ranges:
>> [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
>> [ 0.000000] Movable zone start for each node
>> [ 0.000000] Early memory node ranges
>> [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
>> [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
>> [ 0.000000] On node 0 totalpages: 16384
>> [ 0.000000] free_area_init_node: node 0, pgdat 804904d0,
>> node_mem_map 81000000
>> [ 0.000000] Normal zone: 128 pages used for memmap
>> [ 0.000000] Normal zone: 0 pages reserved
>> [ 0.000000] Normal zone: 16384 pages, LIFO batch:3
>> [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
>> [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
>> linesize 32 bytes
>> [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
>> [ 0.000000] pcpu-alloc: [0] 0
>> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
>> Total pages: 16256
>> [ 0.000000] Kernel command line: parts=1 boot_part_size=4194304
>> gpio=228923 HZ=300000000 mem=64M kmac=4C:5E:0C:DD:A5:54 board=sxt5n
>> boot=0 mlc=7 rootfstype=squashfs noinitrd
>> [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
>> [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
>> [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
>> [ 0.000000] Writing ErrCtl register=00000000
>> [ 0.000000] Readback ErrCtl register=00000000
>> [ 0.000000] Memory: 57856K/65536K available (3408K kernel code,
>> 179K rwdata, 840K rodata, 2028K init, 204K bss, 7680K reserved, 0K
>> cma-reserved)
>> [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
>> [ 0.000000] NR_IRQS:51
>> [ 0.000000] Clocks: CPU:600.000MHz, DDR:400.000MHz, AHB:400.000MHz,
>> Ref:25.000MHz
>> [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles:
>> 0xffffffff, max_idle_ns: 6370868154 ns
>> [ 0.000009] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps
>> every 7158278654ns
>> [ 0.008859] Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
>> [ 0.081948] pid_max: default: 32768 minimum: 301
>> [ 0.087320] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
>> [ 0.094840] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
>> [ 0.105794] clocksource: jiffies: mask: 0xffffffff max_cycles:
>> 0xffffffff, max_idle_ns: 19112604462750000 ns
>> [ 0.118345] NET: Registered protocol family 16
>> [ 0.125038] MIPS: machine is Mikrotik RouterBOARD SXT Lite5
>> [ 0.363076] clocksource: Switched to clocksource MIPS
>> [ 0.370196] NET: Registered protocol family 2
>> [ 0.376159] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
>> [ 0.384143] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
>> [ 0.391366] TCP: Hash tables configured (established 1024 bind 1024)
>> [ 0.398691] UDP hash table entries: 256 (order: 0, 4096 bytes)
>> [ 0.405370] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
>> [ 0.412832] NET: Registered protocol family 1
>> [ 0.417871] PCI: CLS 0 bytes, default 32
>> [ 2.689687] futex hash table entries: 256 (order: -1, 3072 bytes)
>> [ 2.696780] Crashlog allocated RAM at address 0x3f00000
>> [ 2.718540] squashfs: version 4.0 (2009/01/31) Phillip Lougher
>> [ 2.725241] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
>> (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
>> [ 2.798025] io scheduler noop registered
>> [ 2.802493] io scheduler deadline registered (default)
>> [ 2.808701] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
>> [ 2.818749] console [ttyS0] disabled
>> [ 2.842979] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11,
>> base_baud = 1562500) is a 16550A
>> [ 2.852789] console [ttyS0] enabled
>> [ 2.936349] bootconsole [early0] disabled
>> [ 3.038841] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xf1
>> [ 3.115086] nand: Toshiba NAND 128MiB 3,3V 8-bit
>> [ 3.170445] nand: 128 MiB, SLC, erase size: 128 KiB, page size:
>> 2048, OOB size: 64
>> [ 3.261370] Scanning device for bad blocks
>> [ 3.416114] Bad eraseblock 768 at 0x000006000000
>> [ 3.506563] Creating 3 MTD partitions on "ar934x-nfc":
>> [ 3.568229] 0x000000000000-0x000000040000 : "booter"
>> [ 3.629341] 0x000000040000-0x000000400000 : "kernel"
>> [ 3.690716] 0x000000400000-0x000008000000 : "ubi"
>> [ 3.840290] libphy: ag71xx_mdio: probed
>> [ 4.474837] ag71xx-mdio.1: Found an AR934X built-in switch
>> [ 4.577232] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
>> [ 4.651863] NET: Registered protocol family 10
>> [ 4.710174] NET: Registered protocol family 17
>> [ 4.763658] bridge: automatic filtering via arp/ip/ip6tables has
>> been deprecated. Update your scripts to load br_netfilter if you need
>> this.
>> [ 4.915148] 8021q: 802.1Q VLAN Support v1.8
>> [ 4.969495] UBI: auto-attach mtd2
>> [ 5.007162] ubi0: attaching mtd2
>> [ 5.655900] random: nonblocking pool is initialized
>> [ 6.735488] ubi0: scanning is finished
>> [ 6.799577] ubi0: attached mtd2 (name "ubi", size 124 MiB)
>> [ 6.865403] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
>> [ 6.947872] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
>> [ 7.028304] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
>> [ 7.109774] ubi0: good PEBs: 991, bad PEBs: 1, corrupted PEBs: 0
>> [ 7.181864] ubi0: user volume: 3, internal volumes: 1, max. volumes
>> count: 128
>> [ 7.268553] ubi0: max/mean erase counter: 1/0, WL threshold: 4096,
>> image sequence number: 1570949006
>> [ 7.378191] ubi0: available PEBs: 0, total reserved PEBs: 991, PEBs
>> reserved for bad PEB handling: 19
>> [ 7.488932] ubi0: background thread "ubi_bgt0d" started, PID 304
>> [ 7.563139] block ubiblock0_1: created from ubi0:1(rootfs)
>> [ 7.628983] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
>> [ 7.726732] Freeing unused kernel memory: 2028K (804b5000 - 806b0000)
>> [ 7.818293] init: Console is alive
>> [ 7.859421] init: - watchdog -
>> [ 7.911490] kmodloader: loading kernel modules from /etc/modules-boot.d/*
>> [ 7.995762] kmodloader: done loading kernel modules from
>> /etc/modules-boot.d/*
>> [ 8.092963] init: - preinit -
>> [ 8.338394] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
>> [ 9.934325] eth0: link up (1000Mbps/Full duplex)
>> [ 9.989779] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
>> [ 11.567712] eth0: link down
>> [ 11.612223] procd: - early -
>> [ 11.647569] procd: - watchdog -
>> [ 12.249537] procd: - ubus -
>> [ 12.335764] procd: - init -
>> [ 12.544516] kmodloader: loading kernel modules from /etc/modules.d/*
>> [ 12.625395] ip6_tables: (C) 2000-2006 Netfilter Core Team
>> [ 12.702140] Loading modules backported from Linux version
>> wt-2017-01-31-0-ge882dff19e7f
>> [ 12.798300] Backport generated by backports.git
>> backports-20160324-13-g24da7d3c
>> [ 12.893549] ip_tables: (C) 2000-2006 Netfilter Core Team
>> [ 12.966578] nf_conntrack version 0.5.0 (935 buckets, 3740 max)
>> [ 13.087835] xt_time: kernel timezone is -0000
>> [ 13.205582] PPP generic driver version 2.4.2
>> [ 13.259654] NET: Registered protocol family 24
>> [ 13.362601] ath: EEPROM regdomain: 0x0
>> [ 13.362624] ath: EEPROM indicates default country code should be used
>> [ 13.362634] ath: doing EEPROM country->regdmn map search
>> [ 13.362655] ath: country maps to regdmn code: 0x3a
>> [ 13.362666] ath: Country alpha2 being used: US
>> [ 13.362675] ath: Regpair used: 0x3a
>> [ 13.376151] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
>> [ 13.382048] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
>> [ 13.588578] kmodloader: done loading kernel modules from /etc/modules.d/*
>> [ 20.649641] device eth0 entered promiscuous mode
>> [ 20.824351] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
>> [ 22.244326] eth0: link up (1000Mbps/Full duplex)
>> [ 22.363167] br-lan: port 1(eth0) entered forwarding state
>> [ 22.427999] br-lan: port 1(eth0) entered forwarding state
>> [ 22.623138] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
>> [ 24.423129] br-lan: port 1(eth0) entered forwarding state
>>
>> For the sxtg-2hnd (the version with usb, gb lan that newer worked with
>> openwrt) i cant send a boot log, as it doesn't boot and I didn't get
>> serial to work, at least for now.
>>
>> 2017-02-21 0:29 GMT+01:00 Alen Opacic <subixonfire at gmail.com>:
>>> On sxt lite 2 (older version with 128mb nand flash) using
>>> lede-17.01.0-rc2-r3131-42f3c1f-ar71xx-mikrotik-vmlinux-initramfs.elf image,
>>> than sysupgrade to
>>> lede-17.01.0-rc2-r3131-42f3c1f-ar71xx-mikrotik-nand-
>>> large-squashfs-sysupgrade.bin.
>>> After reboot sxt is in a boot loop state, boots allways from network boot
>>> (tftp). This can be called a regresion since this sxt works fine with CC
>>> and wget2nand.
>>>
>>> How can i help debug this ishue.
>>>
>>> Ps: if someone can help maybe we can get sxtg2hnd
>>> (not lite version) to work with
>>> openwrt. This one as far as i know newer worked with openwrt/lede.
>>
>>
>>
>> --
>> <a href="//ipv6.he.net/certification/scoresheet.php?pass_name=subixonfire"
>> target="_blank"><img
>> src="//ipv6.he.net/certification/create_badge.php?pass_name=subixonfire&badge=1"
>> style="border: 0; width: 128px; height: 128px" alt="IPv6 Certification
>> Badge for subixonfire"></img></a>
>
>
>
> --
> <a href="//ipv6.he.net/certification/scoresheet.php?pass_name=subixonfire"
> target="_blank"><img
> src="//ipv6.he.net/certification/create_badge.php?pass_name=subixonfire&badge=1"
> style="border: 0; width: 128px; height: 128px" alt="IPv6 Certification
> Badge for subixonfire"></img></a>
>
> _______________________________________________
> Lede-dev mailing list
> Lede-dev at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/lede-dev
More information about the Lede-dev
mailing list