[LEDE-DEV] [PATCHv2] ipq806x: add support for ZyXEL NBG6817

André Valentin avalentin at marcant.net
Mon Oct 17 12:22:24 PDT 2016


CPU: 1.8GHz ARM, RAM: 512MB
Storage: 4MiB Serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, 5 external and 2 internal Port Switch
WiFi: Dualband, ATH10k 2.4GHz, 5GHz MU-MIMO

Changes:
-remove kernel compression changes
-give spi-nor.c patch a correct name

Signed-off-by: André Valentin <avalentin at marcant.net>
---
 .../linux/ipq806x/base-files/etc/board.d/01_leds   |   5 +
 .../ipq806x/base-files/etc/board.d/02_network      |   4 +
 .../etc/hotplug.d/firmware/11-ath10k-caldata       |   6 +
 target/linux/ipq806x/base-files/lib/ipq806x.sh     |   3 +
 .../base-files/lib/preinit/04_set_mtd_ipq806x.sh   |  21 ++
 .../lib/preinit/05_set_iface_mac_ipq806x.sh        |  21 ++
 .../ipq806x/base-files/lib/upgrade/platform.sh     |   2 +
 target/linux/ipq806x/config-4.4                    |  18 +-
 .../arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts     | 338 +++++++++++++++++++++
 target/linux/ipq806x/image/Makefile                |  26 +-
 .../linux/ipq806x/patches-4.4/800-devicetree.patch |   3 +-
 .../patches-4.4/999-add-spi-nor-mx25u3235f.patch   |  10 +
 12 files changed, 449 insertions(+), 8 deletions(-)
 create mode 100644 target/linux/ipq806x/base-files/lib/preinit/04_set_mtd_ipq806x.sh
 create mode 100644 target/linux/ipq806x/base-files/lib/preinit/05_set_iface_mac_ipq806x.sh
 create mode 100644 target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
 create mode 100644 target/linux/ipq806x/patches-4.4/999-add-spi-nor-mx25u3235f.patch

diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds
index a7ace1f..33774e8 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
@@ -33,6 +33,11 @@ ea8500)
 	ucidef_set_led_wlan "wifi" "WIFI" "ea8500:green:wifi" "phy0radio"
 	ucidef_set_led_default "wps" "WPS" "ea8500:green:wps" "0"
 	;;
+nbg6817)
+	ucidef_set_led_wlan "wifi" "WIFI" "${board}:white:wifi" "phy0radio"
+	ucidef_set_led_wlan "wifi5g" "WIFI5G" "${board}:white:wifi5g" "phy1radio"
+	ucidef_set_led_netdev "wan" "WAN" "${board}:white:internet" "eth0"
+	;;
 *)
 	;;
 esac
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network
index b720455..9168ae7 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -35,6 +35,10 @@ ea8500)
 	ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
 	ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
 	;;
+nbg6817)
+	ucidef_add_switch "switch0" \
+		"1:lan" "2:lan" "3:lan" "4:lan" "6 at eth1" "5:wan" "0 at eth0"
+	;;
 *)
 	echo "Unsupported hardware. Network interfaces not intialized"
 	;;
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index c7977e6..0a9004f 100644
--- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -60,6 +60,9 @@ case "$FIRMWARE" in
          r7800)
 		ath10kcal_extract "art" 4096 12064
 		;;
+         nbg6817)
+		ath10kcal_extract "0:ART" 4096 12064
+		;;
 	esac
 	;;
 "ath10k/cal-pci-0001:01:00.0.bin")
@@ -76,6 +79,9 @@ case "$FIRMWARE" in
         r7800)
 		ath10kcal_extract "art" 20480 12064
 		;;
+         nbg6817)
+		ath10kcal_extract "0:ART" 20480 12064
+		;;
 	esac
 	;;
 *)
diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh b/target/linux/ipq806x/base-files/lib/ipq806x.sh
index ea45381..8f3718c 100644
--- a/target/linux/ipq806x/base-files/lib/ipq806x.sh
+++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh
@@ -38,6 +38,9 @@ ipq806x_board_detect() {
 	*"R7800")
 		name="r7800"
 		;;
+	*"NBG6817")
+		name="nbg6817"
+		;;
 	esac
 
 	[ -z "$name" ] && name="unknown"
diff --git a/target/linux/ipq806x/base-files/lib/preinit/04_set_mtd_ipq806x.sh b/target/linux/ipq806x/base-files/lib/preinit/04_set_mtd_ipq806x.sh
new file mode 100644
index 0000000..024cd81
--- /dev/null
+++ b/target/linux/ipq806x/base-files/lib/preinit/04_set_mtd_ipq806x.sh
@@ -0,0 +1,21 @@
+#
+# Copyright (C) 2009 OpenWrt.org
+#
+
+. /lib/ipq806x.sh
+. /lib/functions/system.sh
+
+preinit_assign_mtd2block() {
+	case $(ipq806x_board_name) in
+		nbg6817)
+			echo "/dev/mmcblk0p2,64KiB,romd" > /sys/module/block2mtd/parameters/block2mtd
+			echo "/dev/mmcblk0p3,64KiB,header" > /sys/module/block2mtd/parameters/block2mtd
+			echo "/dev/mmcblk0p4,64KiB,kernel" > /sys/module/block2mtd/parameters/block2mtd
+			echo "/dev/mmcblk0p6,64KiB,header_1" > /sys/module/block2mtd/parameters/block2mtd
+			echo "/dev/mmcblk0p7,64KiB,kernel_1" > /sys/module/block2mtd/parameters/block2mtd
+			echo "/dev/mmcblk0p8,64KiB,rootfs_1" > /sys/module/block2mtd/parameters/block2mtd
+			;;
+	esac
+}
+
+boot_hook_add preinit_main preinit_assign_mtd2block
diff --git a/target/linux/ipq806x/base-files/lib/preinit/05_set_iface_mac_ipq806x.sh b/target/linux/ipq806x/base-files/lib/preinit/05_set_iface_mac_ipq806x.sh
new file mode 100644
index 0000000..b8246ab
--- /dev/null
+++ b/target/linux/ipq806x/base-files/lib/preinit/05_set_iface_mac_ipq806x.sh
@@ -0,0 +1,21 @@
+#
+# Copyright (C) 2009 OpenWrt.org
+#
+
+. /lib/ipq806x.sh
+. /lib/functions/system.sh
+
+preinit_set_mac_address() {
+	case $(ipq806x_board_name) in
+		nbg6817)
+			mac_lan=$(dd if=/dev/mtdblock9 bs=1 skip=4 count=65532 2>/dev/null | tr \\0 \\n | grep ^ethaddr= | cut -d= -f2)
+			[ -n "$mac_lan" ] && {
+				ifconfig eth0 hw ether "$mac_lan"
+				mac_wan=$(macaddr_add "$mac_lan" 1)
+				ifconfig eth1 hw ether "$mac_wan"
+			}
+			;;
+	esac
+}
+
+boot_hook_add preinit_main preinit_set_mac_address
diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
index 8768930..dd0cb15 100644
--- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
@@ -9,6 +9,7 @@ platform_check_image() {
 	ap148 |\
 	d7800 |\
 	ea8500 |\
+	nbg6817 |\
 	r7500 |\
 	r7500v2 |\
 	r7800)
@@ -34,6 +35,7 @@ platform_pre_upgrade() {
 	case "$board" in
 	ap148 |\
 	d7800 |\
+	nbg6817 |\
 	r7500 |\
 	r7500v2 |\
 	r7800)
diff --git a/target/linux/ipq806x/config-4.4 b/target/linux/ipq806x/config-4.4
index bc04049..c27a827 100644
--- a/target/linux/ipq806x/config-4.4
+++ b/target/linux/ipq806x/config-4.4
@@ -262,6 +257,16 @@ CONFIG_MFD_SYSCON=y
 CONFIG_MIGHT_HAVE_CACHE_L2X0=y
 CONFIG_MIGHT_HAVE_PCI=y
 CONFIG_MIGRATION=y
+CONFIG_MMC=y
+CONFIG_MMC_ARMMMCI=y
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_MINORS=16
+CONFIG_MMC_QCOM_DML=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_MSM=y
+# CONFIG_MMC_SDHCI_PCI is not set
+CONFIG_MMC_SDHCI_PLTFM=y
+# CONFIG_MMC_TIFM_SD is not set
 CONFIG_MODULES_TREE_LOOKUP=y
 CONFIG_MODULES_USE_ELF_REL=y
 CONFIG_MSM_GCC_8660=y
@@ -271,6 +276,7 @@ CONFIG_MSM_GCC_8974=y
 # CONFIG_MSM_LCC_8960 is not set
 CONFIG_MSM_MMCC_8960=y
 CONFIG_MSM_MMCC_8974=y
+CONFIG_MTD_BLOCK2MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_M25P80=y
 CONFIG_MTD_NAND=y
@@ -378,7 +384,6 @@ CONFIG_QCOM_SCM=y
 CONFIG_QCOM_SCM_32=y
 # CONFIG_QCOM_SMD is not set
 CONFIG_QCOM_SMEM=y
-# CONFIG_QCOM_SPMI_TEMP_ALARM is not set
 CONFIG_QCOM_WDT=y
 CONFIG_RAS=y
 CONFIG_RATIONAL=y
@@ -389,6 +394,7 @@ CONFIG_RD_GZIP=y
 CONFIG_REGMAP=y
 CONFIG_REGMAP_MMIO=y
 CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_QCOM_RPM=y
 # CONFIG_REGULATOR_QCOM_SPMI is not set
 CONFIG_RESET_CONTROLLER=y
diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
new file mode 100644
index 0000000..2e1302d
--- /dev/null
+++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
@@ -0,0 +1,338 @@
+#include "qcom-ipq8065-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "ZyXEL NBG6817";
+	compatible = "zyxel,nbg6817", "qcom,ipq8065";
+
+	memory at 0 {
+		reg = <0x42000000 0x1e000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		rsvd at 41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		mdio-gpio0 = &mdio0;
+		sdcc1 = &sdcc1;
+	};
+
+	chosen {
+		bootargs = "rootfstype=squashfs noinitrd block2mtd.block2mtd=/dev/mmcblk0p5,65536,ubi,5 ubi.mtd=ubi";
+		linux,stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		pinmux at 800000 {
+			pinctrl-0 = <&mdio0_pins &rgmii2_pins>;
+			pinctrl-names = "default";
+
+			i2c4_pins: i2c4_pinmux {
+				mux {
+					pins = "gpio12", "gpio13";
+					function = "gsbi4";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			mdio0_pins: mdio0_pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "gpio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				clk {
+					pins = "gpio1";
+					input-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2_pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				tx {
+					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
+					input-disable;
+				};
+			};
+
+			spi_pins: spi_pins {
+				mux {
+					pins = "gpio18", "gpio19", "gpio21";
+					function = "gsbi5";
+					drive-strength = <10>;
+					bias-none;
+				};
+
+				cs {
+					pins = "gpio20";
+					drive-strength = <12>;
+				};
+			};
+		};
+
+		gsbi at 16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "ok";
+			serial at 16340000 {
+				status = "ok";
+			};
+			/*
+			 * The i2c device on gsbi4 should not be enabled.
+			 * On ipq806x designs gsbi4 i2c is meant for exclusive
+			 * RPM usage. Turning this on in kernel manifests as
+			 * i2c failure for the RPM.
+			 */
+		};
+
+		gsbi5: gsbi at 1a200000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "ok";
+
+			spi4: spi at 1a280000 {
+				status = "ok";
+				spi-max-frequency = <50000000>;
+				pinctrl-0 = <&spi_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 20 0>;
+
+				flash: m25p80 at 0 {
+					compatible = "s25fl512s";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					spi-max-frequency = <51200000>;
+					reg = <0>;
+
+					linux,part-probe = "qcom-smem";
+				};
+			};
+		};
+
+		phy at 100f8800 {		/* USB3 port 1 HS phy */
+			status = "ok";
+		};
+
+		phy at 100f8830 {		/* USB3 port 1 SS phy */
+			status = "ok";
+		};
+
+		phy at 110f8800 {		/* USB3 port 0 HS phy */
+			status = "ok";
+		};
+
+		phy at 110f8830 {		/* USB3 port 0 SS phy */
+			status = "ok";
+		};
+
+		usb30 at 0 {
+			status = "ok";
+		};
+
+		usb30 at 1 {
+			status = "ok";
+		};
+
+		pcie0: pci at 1b500000 {
+			status = "ok";
+			reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+			pinctrl-0 = <&pcie0_pins>;
+			pinctrl-names = "default";
+		};
+
+		pcie1: pci at 1b700000 {
+			status = "ok";
+			reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+			pinctrl-0 = <&pcie1_pins>;
+			pinctrl-names = "default";
+		};
+
+		mdio0: mdio {
+			compatible = "virtual,mdio-gpio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
+
+			phy0: ethernet-phy at 0 {
+				device_type = "ethernet-phy";
+				reg = <0>;
+				qca,ar8327-initvals = <
+					0x00004 0x7600000   /* PAD0_MODE */
+					0x00008 0x1000000   /* PAD5_MODE */
+					0x0000c 0x80        /* PAD6_MODE */
+					0x000e4 0xaa545     /* MAC_POWER_SEL */
+					0x000e0 0xc74164de  /* SGMII_CTRL */
+					0x0007c 0x4e        /* PORT0_STATUS */
+					0x00094 0x4e        /* PORT6_STATUS */
+					0x00970 0x1e864443  /* QM_PORT0_CTRL0 */
+					0x00974 0x000001c6  /* QM_PORT0_CTRL1 */
+					0x00978 0x19008643  /* QM_PORT1_CTRL0 */
+					0x0097c 0x000001c6  /* QM_PORT1_CTRL1 */
+					0x00980 0x19008643  /* QM_PORT2_CTRL0 */
+					0x00984 0x000001c6  /* QM_PORT2_CTRL1 */
+					0x00988 0x19008643  /* QM_PORT3_CTRL0 */
+					0x0098c 0x000001c6  /* QM_PORT3_CTRL1 */
+					0x00990 0x19008643  /* QM_PORT4_CTRL0 */
+					0x00994 0x000001c6  /* QM_PORT4_CTRL1 */
+					0x00998 0x1e864443  /* QM_PORT5_CTRL0 */
+					0x0099c 0x000001c6  /* QM_PORT5_CTRL1 */
+					0x009a0 0x1e864443  /* QM_PORT6_CTRL0 */
+					0x009a4 0x000001c6  /* QM_PORT6_CTRL1 */
+					>;
+			};
+
+			phy4: ethernet-phy at 4 {
+				device_type = "ethernet-phy";
+				reg = <4>;
+				qca,ar8327-initvals = <
+					0x000e4 0x6a545     /* MAC_POWER_SEL */
+					0x0000c 0x80        /* PAD6_MODE */
+					>;
+			};
+		};
+
+		gmac1: ethernet at 37200000 {
+			status = "ok";
+			phy-mode = "rgmii";
+			qcom,id = <1>;
+			qcom,phy_mdio_addr = <4>;
+			qcom,poll_required = <0>;
+			qcom,rgmii_delay = <1>;
+			qcom,phy_mii_type = <0>;
+			qcom,emulation = <0>;
+			qcom,irq = <255>;
+			mdiobus = <&mdio0>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		gmac2: ethernet at 37400000 {
+			status = "ok";
+			phy-mode = "sgmii";
+			qcom,id = <2>;
+			qcom,phy_mdio_addr = <0>;	/* none */
+			qcom,poll_required = <0>;	/* no polling */
+			qcom,rgmii_delay = <0>;
+			qcom,phy_mii_type = <1>;
+			qcom,emulation = <0>;
+			qcom,irq = <258>;
+			mdiobus = <&mdio0>;
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		rpm at 108000 {
+			pinctrl-0 = <&i2c4_pins>;
+			pinctrl-names = "default";
+		};
+
+		amba {
+			sdcc1: sdcc at 12400000 {
+				status          = "okay";
+                                dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+                                dma-names = "tx", "rx";
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		wifi {
+			label = "wifi";
+			gpios = <&qcom_pinmux 6 1>;
+			linux,code = <KEY_WLAN>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&qcom_pinmux 54 1>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&qcom_pinmux 65 1>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		internet {
+			label = "nbg6817:white:internet";
+			gpios = <&qcom_pinmux 64 0>;
+		};
+
+		power {
+			label = "nbg6817:white:power";
+			gpios = <&qcom_pinmux 9 0>;
+			default-state = "on";
+		};
+
+		wifi {
+			label = "nbg6817:white:wifi";
+			gpios = <&qcom_pinmux 33 0>;
+		};
+
+		wifi5g {
+			label = "nbg6817:white:wifi5g";
+			gpios = <&qcom_pinmux 26 0>;
+		};
+	};
+
+	gpio_export {
+		compatible = "gpio-export";
+		#size-cells = <0>;
+
+		usb0_status {
+			gpio-export,name = "usb0";
+			gpio-export,output = <1>;
+			gpios = <&qcom_pinmux 15 0>;
+		};
+
+		usb1_status {
+			gpio-export,name = "usb1";
+			gpio-export,output = <1>;
+			gpios = <&qcom_pinmux 16 0>;
+		};
+		usb1_power {
+			gpio-export,name = "usb1_power";
+			gpio-export,output = <1>;
+			gpios = <&qcom_pinmux 14 0>;
+		};
+		usb2_power {
+			gpio-export,name = "usb2_power";
+			gpio-export,output = <1>;
+			gpios = <&qcom_pinmux 17 0>;
+		};
+	};
+};
+
+&adm_dma {
+	status = "ok";
+};
diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile
index 7703a62..4f9a87f 100644
--- a/target/linux/ipq806x/image/Makefile
+++ b/target/linux/ipq806x/image/Makefile
@@ -61,6 +61,18 @@ define Device/UbiFit
 	IMAGE/nand-sysupgrade.tar := sysupgrade-tar
 endef
 
+define Device/ZyXELImage
+	PROFILES += $$(DEVICE_NAME)
+	FILESYSTEMS := squashfs
+	KERNEL_SUFFIX := -uImage
+	KERNEL = kernel-bin | append-dtb | uImage none | pad-to $$(KERNEL_SIZE)
+	KERNEL_NAME := zImage
+	IMAGES := sysupgrade.tar mmcblk0p5-rootfs.bin mmcblk0p4-kernel.bin
+	IMAGE/sysupgrade.tar = sysupgrade-tar
+	IMAGE/mmcblk0p5-rootfs.bin := append-ubi
+	IMAGE/mmcblk0p4-kernel.bin := append-kernel
+endef
+
 define Device/DniImage
 	PROFILES += $$(DEVICE_NAME)
 	FILESYSTEMS := squashfs
@@ -200,6 +212,18 @@ define Device/R7800
 	DEVICE_PACKAGES := ath10k-firmware-qca9984
 endef
 
-TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800
+define Device/NBG6817
+	DEVICE_DTS := qcom-ipq8065-nbg6817
+	KERNEL_SIZE := 4194304
+	BLOCKSIZE := 64k
+	PAGESIZE := 128
+	SUBPAGESIZE := 64
+	BOARD_NAME := nbg6817
+	DEVICE_TITLE := ZyXEL NBG6817
+	DEVICE_PACKAGES := ath10k-firmware-qca9984 kmod-fs-ext4
+	$(call Device/ZyXELImage)
+endef
+
+TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800 NBG6817
 
 $(eval $(call BuildImage))
diff --git a/target/linux/ipq806x/patches-4.4/800-devicetree.patch b/target/linux/ipq806x/patches-4.4/800-devicetree.patch
index 85f2534..922dcfc 100644
--- a/target/linux/ipq806x/patches-4.4/800-devicetree.patch
+++ b/target/linux/ipq806x/patches-4.4/800-devicetree.patch
@@ -12,7 +12,7 @@ Signed-off-by: Jonas Gorski <jogo at openwrt.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -506,7 +506,13 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -506,7 +506,14 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
  	qcom-ipq8064-ap148.dtb \
@@ -23,6 +23,7 @@ Signed-off-by: Jonas Gorski <jogo at openwrt.org>
 +	qcom-ipq8064-r7500.dtb \
 +	qcom-ipq8064-r7500v2.dtb \
 +	qcom-ipq8065-r7800.dtb \
++	qcom-ipq8065-nbg6817.dtb \
  	qcom-msm8660-surf.dtb \
  	qcom-msm8960-cdp.dtb \
  	qcom-msm8974-sony-xperia-honami.dtb
diff --git a/target/linux/ipq806x/patches-4.4/999-add-spi-nor-mx25u3235f.patch b/target/linux/ipq806x/patches-4.4/999-add-spi-nor-mx25u3235f.patch
new file mode 100644
index 0000000..45533e1
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.4/477-add-spi-nor-mx25u3235f.patch
@@ -0,0 +1,10 @@
+--- a/drivers/mtd/spi-nor/spi-nor.c	2016-10-09 00:34:19.206155838 +0200
++++ b/drivers/mtd/spi-nor/spi-nor.c	2016-10-09 00:37:11.048495602 +0200
+@@ -721,6 +721,7 @@ static const struct flash_info spi_nor_i
+ 	{ "mx25l3205d",  INFO(0xc22016, 0, 64 * 1024,  64, SECT_4K) },
+ 	{ "mx25l3255e",  INFO(0xc29e16, 0, 64 * 1024,  64, SECT_4K) },
+ 	{ "mx25l6405d",  INFO(0xc22017, 0, 64 * 1024, 128, SECT_4K) },
++	{ "mx25u3235f",	 INFO(0xc22536, 0, 64 * 1024, 64, 0) },
+ 	{ "mx25u6435f",  INFO(0xc22537, 0, 64 * 1024, 128, SECT_4K) },
+ 	{ "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
+ 	{ "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
-- 
2.1.4




More information about the Lede-dev mailing list