[LEDE-DEV] [PATCH 02/11] orion: Add support for 4.4 kernel
Florian Fainelli
f.fainelli at gmail.com
Tue Nov 29 17:09:56 PST 2016
Patches and configuration apply just fine on the Marvell Orion target.
Signed-off-by: Florian Fainelli <f.fainelli at gmail.com>
---
target/linux/orion/config-4.4 | 422 +++++++++++++++
.../100-wrt350nv2_openwrt_partition_map.patch | 32 ++
.../patches-4.4/101-wnr854t_partition_map.patch | 25 +
.../orion/patches-4.4/200-dt2_board_support.patch | 570 +++++++++++++++++++++
.../orion/patches-4.4/210-wn802t_support.patch | 75 +++
5 files changed, 1124 insertions(+)
create mode 100644 target/linux/orion/config-4.4
create mode 100644 target/linux/orion/patches-4.4/100-wrt350nv2_openwrt_partition_map.patch
create mode 100644 target/linux/orion/patches-4.4/101-wnr854t_partition_map.patch
create mode 100644 target/linux/orion/patches-4.4/200-dt2_board_support.patch
create mode 100644 target/linux/orion/patches-4.4/210-wn802t_support.patch
diff --git a/target/linux/orion/config-4.4 b/target/linux/orion/config-4.4
new file mode 100644
index 000000000000..472850199e34
--- /dev/null
+++ b/target/linux/orion/config-4.4
@@ -0,0 +1,422 @@
+# CONFIG_AF_KCM is not set
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_APM_EMULATION is not set
+# CONFIG_AQUANTIA_PHY is not set
+# CONFIG_ARCH_ASPEED is not set
+CONFIG_ARCH_CLOCKSOURCE_DATA=y
+CONFIG_ARCH_HAS_DEVMEM_IS_ALLOWED=y
+CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
+CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
+CONFIG_ARCH_HAS_SG_CHAIN=y
+CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
+CONFIG_ARCH_MMAP_RND_BITS=8
+CONFIG_ARCH_MMAP_RND_BITS_MAX=16
+CONFIG_ARCH_MMAP_RND_BITS_MIN=8
+CONFIG_ARCH_MULTIPLATFORM=y
+CONFIG_ARCH_MULTI_CPU_AUTO=y
+# CONFIG_ARCH_MULTI_V4 is not set
+# CONFIG_ARCH_MULTI_V4T is not set
+CONFIG_ARCH_MULTI_V4_V5=y
+CONFIG_ARCH_MULTI_V5=y
+CONFIG_ARCH_NR_GPIO=0
+CONFIG_ARCH_ORION5X=y
+# CONFIG_ARCH_ORION5X_DT is not set
+# CONFIG_ARCH_OXNAS is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
+CONFIG_ARCH_SUPPORTS_UPROBES=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARCH_USE_BUILTIN_BSWAP=y
+CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
+# CONFIG_ARCH_WANTS_UBSAN_NO_NULL is not set
+CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_ARM=y
+# CONFIG_ARM_CPU_SUSPEND is not set
+# CONFIG_ARM_CRYPTO is not set
+CONFIG_ARM_GIC_MAX_NR=1
+CONFIG_ARM_HAS_SG_CHAIN=y
+CONFIG_ARM_L1_CACHE_SHIFT=5
+# CONFIG_ARM_MODULE_PLTS is not set
+CONFIG_ARM_PATCH_PHYS_VIRT=y
+# CONFIG_ARM_THUMB is not set
+# CONFIG_ARM_TIMER_SP804 is not set
+CONFIG_ATAGS=y
+# CONFIG_ATH5K_PCI is not set
+CONFIG_AUTO_ZRELADDR=y
+# CONFIG_BINFMT_FLAT is not set
+CONFIG_BLK_MQ_PCI=y
+# CONFIG_BNXT is not set
+# CONFIG_CACHE_L2X0 is not set
+CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE=y
+CONFIG_CLKDEV_LOOKUP=y
+CONFIG_CLKSRC_MMIO=y
+CONFIG_CLKSRC_OF=y
+CONFIG_CLKSRC_PROBE=y
+# CONFIG_CLK_QORIQ is not set
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_CMDLINE="rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 earlyprintk"
+CONFIG_CMDLINE_FORCE=y
+CONFIG_COMMON_CLK=y
+# CONFIG_COMMON_CLK_NXP is not set
+# CONFIG_COMMON_CLK_PIC32 is not set
+# CONFIG_COMMON_CLK_XLNX_CLKWZRD is not set
+# CONFIG_CORESIGHT is not set
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_COPY_FEROCEON=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_CPU_FEROCEON=y
+CONFIG_CPU_FEROCEON_OLD_ID=y
+# CONFIG_CPU_ICACHE_DISABLE is not set
+# CONFIG_CPU_NO_EFFICIENT_FFS is not set
+CONFIG_CPU_PABRT_LEGACY=y
+CONFIG_CPU_SW_DOMAIN_PAN=y
+CONFIG_CPU_TLB_FEROCEON=y
+CONFIG_CPU_USE_DOMAINS=y
+# CONFIG_CXL_AFU_DRIVER_OPS is not set
+CONFIG_DEBUG_LL=y
+CONFIG_DEBUG_LL_INCLUDE="debug/8250.S"
+CONFIG_DEBUG_LL_UART_8250=y
+# CONFIG_DEBUG_MVEBU_UART0_ALTERNATE is not set
+# CONFIG_DEBUG_TEST_DRIVER_REMOVE is not set
+# CONFIG_DEBUG_TIMEKEEPING is not set
+# CONFIG_DEBUG_UART_8250 is not set
+# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set
+# CONFIG_DEBUG_UART_8250_PALMCHIP is not set
+CONFIG_DEBUG_UART_8250_SHIFT=2
+# CONFIG_DEBUG_UART_8250_WORD is not set
+CONFIG_DEBUG_UART_PHYS=0xf1012000
+CONFIG_DEBUG_UART_VIRT=0xfe012000
+CONFIG_DEBUG_UNCOMPRESS=y
+# CONFIG_DEBUG_USER is not set
+# CONFIG_DEBUG_WQ_FORCE_RR_CPU is not set
+CONFIG_DEVMEM=y
+CONFIG_DNOTIFY=y
+# CONFIG_DP83848_PHY is not set
+# CONFIG_DP83867_PHY is not set
+# CONFIG_DST_CACHE is not set
+CONFIG_DTC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_EDAC_ATOMIC_SCRUB=y
+CONFIG_EDAC_SUPPORT=y
+# CONFIG_EFI is not set
+CONFIG_ELFCORE=y
+# CONFIG_EXPORTFS_BLOCK_OPS is not set
+# CONFIG_EZCHIP_NPS_MANAGEMENT_ENET is not set
+CONFIG_FIXED_PHY=y
+CONFIG_FIX_EARLYCON_MEM=y
+# CONFIG_FPGA is not set
+CONFIG_FRAME_POINTER=y
+# CONFIG_FS_ENCRYPTION is not set
+# CONFIG_FW_CFG_SYSFS is not set
+# CONFIG_GCC_PLUGINS is not set
+CONFIG_GENERIC_ALLOCATOR=y
+CONFIG_GENERIC_ATOMIC64=y
+CONFIG_GENERIC_BUG=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_EARLY_IOREMAP=y
+CONFIG_GENERIC_IDLE_POLL_SETUP=y
+CONFIG_GENERIC_IO=y
+CONFIG_GENERIC_IRQ_CHIP=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_SCHED_CLOCK=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GENERIC_STRNCPY_FROM_USER=y
+CONFIG_GENERIC_STRNLEN_USER=y
+# CONFIG_GOLDFISH is not set
+CONFIG_GPIOLIB=y
+# CONFIG_GPIO_74XX_MMIO is not set
+# CONFIG_GPIO_ALTERA is not set
+# CONFIG_GPIO_MOCKUP is not set
+# CONFIG_GPIO_MPC8XXX is not set
+CONFIG_GPIO_MVEBU=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_GPIO_ZX is not set
+# CONFIG_GREYBUS is not set
+CONFIG_HANDLE_DOMAIN_IRQ=y
+# CONFIG_HARDENED_USERCOPY is not set
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT_MAP=y
+# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
+CONFIG_HAVE_ARCH_AUDITSYSCALL=y
+# CONFIG_HAVE_ARCH_BITREVERSE is not set
+CONFIG_HAVE_ARCH_HARDENED_USERCOPY=y
+# CONFIG_HAVE_ARCH_HASH is not set
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_MMAP_RND_BITS=y
+CONFIG_HAVE_ARCH_PFN_VALID=y
+CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+# CONFIG_HAVE_ARCH_VMAP_STACK is not set
+# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
+CONFIG_HAVE_CBPF_JIT=y
+CONFIG_HAVE_CC_STACKPROTECTOR=y
+CONFIG_HAVE_CLK=y
+CONFIG_HAVE_CLK_PREPARE=y
+CONFIG_HAVE_CONTEXT_TRACKING=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DEBUG_KMEMLEAK=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_DMA_CONTIGUOUS=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_EXIT_THREAD=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_GCC_PLUGINS=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_HAVE_HARDENED_USERCOPY_ALLOCATOR=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_LZ4=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_HAVE_KERNEL_LZO=y
+CONFIG_HAVE_KERNEL_XZ=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_NET_DSA=y
+CONFIG_HAVE_NMI=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_OPTPROBES=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HAVE_PERF_REGS=y
+CONFIG_HAVE_PERF_USER_STACK_DUMP=y
+CONFIG_HAVE_PROC_CPU=y
+CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
+CONFIG_HAVE_UID16=y
+CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
+# CONFIG_HIP04_ETH is not set
+# CONFIG_HISI_FEMAC is not set
+# CONFIG_HNS is not set
+# CONFIG_HNS_DSAF is not set
+# CONFIG_HNS_ENET is not set
+CONFIG_HZ_FIXED=0
+CONFIG_HZ_PERIODIC=y
+# CONFIG_IDLE_PAGE_TRACKING is not set
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_INTEL_TH is not set
+# CONFIG_INTEL_XWAY_PHY is not set
+CONFIG_IOMMU_HELPER=y
+CONFIG_IRQCHIP=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_FORCED_THREADING=y
+# CONFIG_IRQ_POLL is not set
+CONFIG_IRQ_WORK=y
+# CONFIG_ISA_BUS_API is not set
+# CONFIG_LEDS_BCM6328 is not set
+# CONFIG_LEDS_BCM6358 is not set
+# CONFIG_LEDS_CLASS_FLASH is not set
+CONFIG_LEDS_GPIO=y
+# CONFIG_LEDS_TRIGGER_MTD is not set
+# CONFIG_LEDS_TRIGGER_PANIC is not set
+CONFIG_LIBFDT=y
+# CONFIG_LNET is not set
+# CONFIG_LWTUNNEL is not set
+CONFIG_MAC80211_STA_HASH_MAX_SIZE=0
+# CONFIG_MACH_ASM9260 is not set
+# CONFIG_MACH_D2NET_DT is not set
+# CONFIG_MACH_DB88F5281 is not set
+# CONFIG_MACH_DNS323 is not set
+# CONFIG_MACH_DT2 is not set
+# CONFIG_MACH_KUROBOX_PRO is not set
+# CONFIG_MACH_LINKSTATION_LSCHL is not set
+# CONFIG_MACH_LINKSTATION_LS_HGL is not set
+# CONFIG_MACH_LINKSTATION_MINI is not set
+# CONFIG_MACH_LINKSTATION_PRO is not set
+# CONFIG_MACH_MSS2_DT is not set
+# CONFIG_MACH_MV2120 is not set
+# CONFIG_MACH_NET2BIG is not set
+# CONFIG_MACH_RD88F5181L_FXO is not set
+# CONFIG_MACH_RD88F5181L_GE is not set
+# CONFIG_MACH_RD88F5182 is not set
+# CONFIG_MACH_RD88F5182_DT is not set
+# CONFIG_MACH_RD88F6183AP_GE is not set
+# CONFIG_MACH_TERASTATION_PRO2 is not set
+# CONFIG_MACH_TS209 is not set
+# CONFIG_MACH_TS409 is not set
+# CONFIG_MACH_TS78XX is not set
+CONFIG_MACH_WNR854T=y
+CONFIG_MACH_WRT350N_V2=y
+# CONFIG_MACSEC is not set
+CONFIG_MANDATORY_FILE_LOCKING=y
+CONFIG_MAY_USE_DEVLINK=y
+# CONFIG_MDIO_HISI_FEMAC is not set
+CONFIG_MEMBARRIER=y
+# CONFIG_MEMTEST is not set
+# CONFIG_MFD_ATMEL_FLEXCOM is not set
+# CONFIG_MFD_ATMEL_HLCDC is not set
+# CONFIG_MFD_EXYNOS_LPASS is not set
+# CONFIG_MFD_MT6397 is not set
+# CONFIG_MICROCHIP_PHY is not set
+# CONFIG_MICROSEMI_PHY is not set
+CONFIG_MIGHT_HAVE_PCI=y
+# CONFIG_MLXSW_CORE is not set
+CONFIG_MODULES_USE_ELF_REL=y
+# CONFIG_MOST is not set
+# CONFIG_MPLS is not set
+# CONFIG_MTD_PARTITIONED_MASTER is not set
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MULTIUSER=y
+CONFIG_MULTI_IRQ_HANDLER=y
+CONFIG_MV643XX_ETH=y
+CONFIG_MVEBU_MBUS=y
+CONFIG_MVMDIO=y
+# CONFIG_MVNETA is not set
+# CONFIG_MVNETA_BM is not set
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEED_KUSER_HELPERS=y
+CONFIG_NEED_PER_CPU_KM=y
+# CONFIG_NET_CLS_FLOWER is not set
+# CONFIG_NET_CLS_MATCHALL is not set
+# CONFIG_NET_DEVLINK is not set
+# CONFIG_NET_L3_MASTER_DEV is not set
+# CONFIG_NET_NCSI is not set
+# CONFIG_NET_SWITCHDEV is not set
+CONFIG_NET_VENDOR_AMAZON=y
+# CONFIG_NET_VENDOR_AURORA is not set
+CONFIG_NET_VENDOR_CAVIUM=y
+CONFIG_NET_VENDOR_EZCHIP=y
+CONFIG_NET_VENDOR_NETRONOME=y
+CONFIG_NET_VENDOR_RENESAS=y
+CONFIG_NET_VENDOR_ROCKER=y
+CONFIG_NET_VENDOR_SYNOPSYS=y
+CONFIG_NMI_LOG_BUF_SHIFT=13
+CONFIG_NO_BOOTMEM=y
+# CONFIG_NTB is not set
+# CONFIG_NVM is not set
+# CONFIG_NVMEM is not set
+CONFIG_OF=y
+CONFIG_OF_ADDRESS=y
+CONFIG_OF_ADDRESS_PCI=y
+CONFIG_OF_EARLY_FLATTREE=y
+CONFIG_OF_FLATTREE=y
+CONFIG_OF_GPIO=y
+CONFIG_OF_IRQ=y
+CONFIG_OF_MDIO=y
+CONFIG_OF_NET=y
+# CONFIG_OF_OVERLAY is not set
+CONFIG_OF_PCI=y
+CONFIG_OF_PCI_IRQ=y
+CONFIG_OF_RESERVED_MEM=y
+# CONFIG_OF_UNITTEST is not set
+CONFIG_OLD_SIGACTION=y
+CONFIG_OLD_SIGSUSPEND3=y
+# CONFIG_ORANGEFS_FS is not set
+# CONFIG_PAGE_EXTENSION is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PAGE_OWNER is not set
+# CONFIG_PARAVIRT is not set
+# CONFIG_PARAVIRT_TIME_ACCOUNTING is not set
+CONFIG_PCI=y
+# CONFIG_PCIE_ALTERA is not set
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_DOMAINS_GENERIC=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PGTABLE_LEVELS=2
+CONFIG_PHYLIB=y
+# CONFIG_PHY_PXA_28NM_HSIC is not set
+# CONFIG_PHY_PXA_28NM_USB2 is not set
+CONFIG_PLAT_ORION=y
+CONFIG_PLAT_ORION_LEGACY=y
+CONFIG_PRINTK_NMI=y
+# CONFIG_PROC_CHILDREN is not set
+# CONFIG_QCOM_EMAC is not set
+# CONFIG_QED is not set
+# CONFIG_RAS is not set
+CONFIG_RATIONAL=y
+# CONFIG_RCU_EQS_DEBUG is not set
+# CONFIG_RCU_EXPEDITE_BOOT is not set
+# CONFIG_RCU_EXPERT is not set
+# CONFIG_RCU_PERF_TEST is not set
+# CONFIG_RCU_STALL_COMMON is not set
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_SBITMAP=y
+CONFIG_SCHED_HRTICK=y
+# CONFIG_SCHED_INFO is not set
+# CONFIG_SCSI_DMA is not set
+CONFIG_SECTION_MISMATCH_WARN_ONLY=y
+CONFIG_SERIAL_8250_FSL=y
+# CONFIG_SERIAL_8250_MOXA is not set
+# CONFIG_SERIAL_8250_RT288X is not set
+# CONFIG_SERIAL_BCM63XX is not set
+# CONFIG_SERIAL_CONEXANT_DIGICOLOR is not set
+# CONFIG_SERIAL_STM32 is not set
+# CONFIG_SG_POOL is not set
+# CONFIG_SG_SPLIT is not set
+# CONFIG_SLAB_FREELIST_RANDOM is not set
+# CONFIG_SOCK_CGROUP_DATA is not set
+# CONFIG_SOC_BRCMSTB is not set
+CONFIG_SPARSE_IRQ=y
+CONFIG_SPLIT_PTLOCK_CPUS=999999
+# CONFIG_SQUASHFS_LZ4 is not set
+CONFIG_SRAM=y
+CONFIG_SRCU=y
+# CONFIG_STAGING_BOARD is not set
+# CONFIG_STM is not set
+# CONFIG_STREAM_PARSER is not set
+# CONFIG_SUNXI_SRAM is not set
+CONFIG_SWIOTLB=y
+CONFIG_SWPHY=y
+# CONFIG_SYNC_FILE is not set
+# CONFIG_SYNOPSYS_DWC_ETH_QOS is not set
+# CONFIG_SYSTEM_DATA_VERIFICATION is not set
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+# CONFIG_TCP_CONG_BBR is not set
+# CONFIG_TCP_CONG_CDG is not set
+# CONFIG_TCP_CONG_NV is not set
+# CONFIG_TERANETICS_PHY is not set
+# CONFIG_TEST_BITMAP is not set
+# CONFIG_TEST_HASH is not set
+# CONFIG_TEST_HEXDUMP is not set
+# CONFIG_TEST_PRINTF is not set
+# CONFIG_TEST_STATIC_KEYS is not set
+# CONFIG_TEST_UUID is not set
+CONFIG_TICK_CPU_ACCOUNTING=y
+# CONFIG_TI_CPSW_ALE is not set
+# CONFIG_TRIM_UNUSED_KSYMS is not set
+# CONFIG_TUN_VNET_CROSS_LE is not set
+# CONFIG_UBSAN is not set
+CONFIG_UID16=y
+CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
+CONFIG_USB_SUPPORT=y
+# CONFIG_USB_ULPI_BUS is not set
+# CONFIG_USERFAULTFD is not set
+CONFIG_USE_OF=y
+CONFIG_VECTORS_BASE=0xffff0000
+# CONFIG_VFP is not set
+# CONFIG_WATCHDOG_PRETIMEOUT_GOV is not set
+# CONFIG_WATCHDOG_SYSFS is not set
+CONFIG_WLAN_VENDOR_ADMTEK=y
+CONFIG_WLAN_VENDOR_ATH=y
+CONFIG_WLAN_VENDOR_ATMEL=y
+CONFIG_WLAN_VENDOR_BROADCOM=y
+CONFIG_WLAN_VENDOR_CISCO=y
+CONFIG_WLAN_VENDOR_INTEL=y
+CONFIG_WLAN_VENDOR_INTERSIL=y
+CONFIG_WLAN_VENDOR_MARVELL=y
+CONFIG_WLAN_VENDOR_MEDIATEK=y
+CONFIG_WLAN_VENDOR_RALINK=y
+CONFIG_WLAN_VENDOR_REALTEK=y
+CONFIG_WLAN_VENDOR_RSI=y
+CONFIG_WLAN_VENDOR_ST=y
+CONFIG_WLAN_VENDOR_TI=y
+CONFIG_WLAN_VENDOR_ZYDAS=y
+# CONFIG_WQ_WATCHDOG is not set
+# CONFIG_XILINX_GMII2RGMII is not set
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_BCJ=y
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ZBOOT_ROM_TEXT=0x0
diff --git a/target/linux/orion/patches-4.4/100-wrt350nv2_openwrt_partition_map.patch b/target/linux/orion/patches-4.4/100-wrt350nv2_openwrt_partition_map.patch
new file mode 100644
index 000000000000..89c2c9420bf1
--- /dev/null
+++ b/target/linux/orion/patches-4.4/100-wrt350nv2_openwrt_partition_map.patch
@@ -0,0 +1,32 @@
+--- a/arch/arm/mach-orion5x/wrt350n-v2-setup.c
++++ b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
+@@ -134,11 +134,11 @@ static struct mtd_partition wrt350n_v2_n
+ {
+ .name = "kernel",
+ .offset = 0x00000000,
+- .size = 0x00760000,
++ .size = 0x00140000, // change to kernel mtd size here (1/3)
+ }, {
+ .name = "rootfs",
+- .offset = 0x001a0000,
+- .size = 0x005c0000,
++ .offset = 0x00140000, // change to kernel mtd size here (2/3)
++ .size = 0x00610000, // adopt to kernel mtd size here (3/3) = 0x00750000 - <kernel mtd size>
+ }, {
+ .name = "lang",
+ .offset = 0x00760000,
+@@ -151,6 +151,14 @@ static struct mtd_partition wrt350n_v2_n
+ .name = "u-boot",
+ .offset = 0x007c0000,
+ .size = 0x00040000,
++ }, {
++ .name = "eRcOmM_do_not_touch",
++ .offset = 0x00750000,
++ .size = 0x00010000, // erasesize
++ }, {
++ .name = "image", // for sysupgrade
++ .offset = 0x00000000,
++ .size = 0x00750000,
+ },
+ };
+
diff --git a/target/linux/orion/patches-4.4/101-wnr854t_partition_map.patch b/target/linux/orion/patches-4.4/101-wnr854t_partition_map.patch
new file mode 100644
index 000000000000..881cfb773ea5
--- /dev/null
+++ b/target/linux/orion/patches-4.4/101-wnr854t_partition_map.patch
@@ -0,0 +1,25 @@
+--- a/arch/arm/mach-orion5x/wnr854t-setup.c
++++ b/arch/arm/mach-orion5x/wnr854t-setup.c
+@@ -57,15 +57,19 @@ static struct mtd_partition wnr854t_nor_
+ {
+ .name = "kernel",
+ .offset = 0x00000000,
+- .size = 0x00100000,
++ .size = 0x00140000,
+ }, {
+ .name = "rootfs",
+- .offset = 0x00100000,
+- .size = 0x00660000,
++ .offset = 0x00140000,
++ .size = 0x00620000,
+ }, {
+ .name = "uboot",
+ .offset = 0x00760000,
+ .size = 0x00040000,
++ }, {
++ .name = "image", // for sysupgrade
++ .offset = 0x00000000,
++ .size = 0x00760000,
+ },
+ };
+
diff --git a/target/linux/orion/patches-4.4/200-dt2_board_support.patch b/target/linux/orion/patches-4.4/200-dt2_board_support.patch
new file mode 100644
index 000000000000..3d2efffe6831
--- /dev/null
+++ b/target/linux/orion/patches-4.4/200-dt2_board_support.patch
@@ -0,0 +1,570 @@
+Index: linux-3.18.43/arch/arm/mach-orion5x/Kconfig
+===================================================================
+--- linux-3.18.43.orig/arch/arm/mach-orion5x/Kconfig
++++ linux-3.18.43/arch/arm/mach-orion5x/Kconfig
+@@ -36,6 +36,13 @@ config MACH_RD88F5182_DT
+ Say 'Y' here if you want your kernel to support the Marvell
+ Orion-NAS (88F5182) RD2, Flattened Device Tree.
+
++config MACH_DT2
++ bool "Freecom DataTank Gateway"
++ select I2C_BOARDINFO
++ help
++ Say 'Y' here if you want your kernel to support the
++ Freecom DataTank Gateway
++
+ config MACH_KUROBOX_PRO
+ bool "KuroBox Pro"
+ select I2C_BOARDINFO
+Index: linux-3.18.43/arch/arm/mach-orion5x/Makefile
+===================================================================
+--- linux-3.18.43.orig/arch/arm/mach-orion5x/Makefile
++++ linux-3.18.43/arch/arm/mach-orion5x/Makefile
+@@ -14,6 +14,7 @@ obj-$(CONFIG_MACH_TS78XX) += ts78xx-setu
+ obj-$(CONFIG_MACH_MV2120) += mv2120-setup.o
+ obj-$(CONFIG_MACH_NET2BIG) += net2big-setup.o
+ obj-$(CONFIG_MACH_WNR854T) += wnr854t-setup.o
++obj-$(CONFIG_MACH_DT2) += dt2-setup.o
+ obj-$(CONFIG_MACH_RD88F5181L_GE) += rd88f5181l-ge-setup.o
+ obj-$(CONFIG_MACH_RD88F5181L_FXO) += rd88f5181l-fxo-setup.o
+ obj-$(CONFIG_MACH_RD88F6183AP_GE) += rd88f6183ap-ge-setup.o
+Index: linux-3.18.43/arch/arm/mach-orion5x/dt2-common.h
+===================================================================
+--- /dev/null
++++ linux-3.18.43/arch/arm/mach-orion5x/dt2-common.h
+@@ -0,0 +1,82 @@
++#ifndef __INC_DT2_COMMON_H
++#define __INC_DT2_COMMON_H
++
++#define ATAG_MV_UBOOT 0x41000403
++
++struct tag_mv_uboot {
++ u32 uboot_version;
++ u32 tclk;
++ u32 sysclk;
++ u32 isUsbHost;
++ u32 overEthAddr;
++ u8 dt2_eeprom[256];
++};
++
++#define DT2_EEPROM_ADDR 0x50
++#define DT2_EEPROM_OFFSET 0
++#define DT2_EEPROM_LENGTH 256
++
++#define DT2_SERIAL_NUMBER_DEFAULT "run on default\0"
++#define DT2_REVISION_DEFAULT_INIT 0xFF
++#define DT2_CONFIG_FLAGS_DEFAULT 0x00
++
++#define _PACKED_ __attribute__((packed))
++
++struct DT2_EEPROM_SD_CONFIG {
++ unsigned int ram_1;
++ unsigned int ram_2;
++ unsigned int ram_3;
++ unsigned int ram_4;
++ unsigned char ram_5;
++ unsigned char ram_6;
++ unsigned short ram_7;
++ unsigned int magic_id;
++ } _PACKED_; // 24 Bytes in total
++
++struct DT2_EEPROM_FC_CONFIG {
++ unsigned char rtc_sts_mask;
++ unsigned char rtc_sts_init;
++ unsigned char rtc_int_mask;
++ unsigned char rtc_int_init;
++ unsigned char rtc_atrim_init;
++ unsigned char rtc_dtrim_init;
++ unsigned char dummy1;
++ unsigned char dummy2;
++ unsigned char dt2_config_flags; /* 0x80 to load rtc_values to RTC */
++ unsigned char dt2_revision; /* upper nibble is HW, lower nibble is FW */
++ unsigned char dt2_serial_number[16]; /* Serial number of DT-2 */
++ } _PACKED_; // 26 Bytes in total
++
++#define CFG_LOAD_RTC_VALUES 0x80
++
++struct DT2_EEPROM_GW_CONFIG {
++ unsigned int dummy1;
++ unsigned int dummy2;
++ unsigned int dummy3;
++ unsigned char dummy4;
++ unsigned char tos_video_val1;
++ unsigned char tos_video_val2;
++ unsigned char tos_voip_val;
++ unsigned char qos_igmp_cfg;
++ unsigned char num_of_ifs;
++ unsigned short vlan_ports_if[3];
++ unsigned char mac_addr[3][6];
++ } _PACKED_; // 42 Bytes in total
++
++#define _SIZE_OF_ALL_STRUCTS_ (sizeof(struct DT2_EEPROM_SD_CONFIG) + sizeof(struct DT2_EEPROM_FC_CONFIG) + sizeof(struct DT2_EEPROM_GW_CONFIG))
++
++// MV = EEPROM - SD - FC - GW - CRC
++struct DT2_EEPROM_MV_CONFIG {
++ unsigned int reg_addr[(DT2_EEPROM_LENGTH - _SIZE_OF_ALL_STRUCTS_ - sizeof(unsigned int)) / (sizeof(unsigned int) * 2)];
++ unsigned int reg_data[(DT2_EEPROM_LENGTH - _SIZE_OF_ALL_STRUCTS_ - sizeof(unsigned int)) / (sizeof(unsigned int) * 2)];
++ } _PACKED_;
++
++struct DT2_EEPROM_STRUCT {
++ struct DT2_EEPROM_MV_CONFIG mv;
++ struct DT2_EEPROM_SD_CONFIG sd;
++ struct DT2_EEPROM_FC_CONFIG fc;
++ struct DT2_EEPROM_GW_CONFIG gw;
++ unsigned int crc;
++ } _PACKED_;
++
++#endif
+Index: linux-3.18.43/arch/arm/mach-orion5x/dt2-setup.c
+===================================================================
+--- /dev/null
++++ linux-3.18.43/arch/arm/mach-orion5x/dt2-setup.c
+@@ -0,0 +1,448 @@
++/*
++ * arch/arm/mach-orion5x/dt2-setup.c
++ *
++ * Freecom DataTank Gateway Setup
++ *
++ * Copyright (C) 2009 Zintis Petersons <Zintis.Petersons at abcsolutions.lv>
++ *
++ * This file is licensed under the terms of the GNU General Public
++ * License version 2. This program is licensed "as is" without any
++ * warranty of any kind, whether express or implied.
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++#include <linux/pci.h>
++#include <linux/irq.h>
++#include <linux/mtd/physmap.h>
++#include <linux/mv643xx_eth.h>
++#include <linux/ethtool.h>
++#include <linux/if_ether.h>
++#include <net/dsa.h>
++#include <linux/ata_platform.h>
++#include <linux/i2c.h>
++#include <linux/reboot.h>
++#include <linux/interrupt.h>
++#include <asm/mach-types.h>
++#include <asm/gpio.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/pci.h>
++#include <mach/orion5x.h>
++#include "common.h"
++#include "mpp.h"
++
++/*****************************************************************************
++ * DT2 local
++ ****************************************************************************/
++#include <asm/setup.h>
++#include "dt2-common.h"
++
++u32 mvUbootVer = 0;
++u32 mvTclk = 166666667;
++u32 mvSysclk = 200000000;
++u32 mvIsUsbHost = 1;
++u32 overEthAddr = 0;
++u32 gBoardId = -1;
++struct DT2_EEPROM_STRUCT dt2_eeprom;
++
++/*****************************************************************************
++ * DT2 Info
++ ****************************************************************************/
++/*
++ * PCI
++ */
++
++#define DT2_PCI_SLOT0_OFFS 7
++#define DT2_PCI_SLOT0_IRQ_A_PIN 3
++#define DT2_PCI_SLOT0_IRQ_B_PIN 2
++
++#define DT2_PIN_GPIO_SYNC 25
++#define DT2_PIN_GPIO_POWER 24
++#define DT2_PIN_GPIO_UNPLUG1 23
++#define DT2_PIN_GPIO_UNPLUG2 22
++#define DT2_PIN_GPIO_RESET 4
++
++#define DT2_NOR_BOOT_BASE 0xf4000000
++#define DT2_NOR_BOOT_SIZE SZ_512K
++
++#define DT2_LEDS_BASE 0xfa000000
++#define DT2_LEDS_SIZE SZ_1K
++
++/*****************************************************************************
++ * 512K NOR Flash on Device bus Boot CS
++ ****************************************************************************/
++
++static struct mtd_partition dt2_partitions[] = {
++ {
++ .name = "u-boot",
++ .size = 0x00080000,
++ .offset = 0,
++ },
++};
++
++static struct physmap_flash_data dt2_nor_flash_data = {
++ .width = 1, /* 8 bit bus width */
++ .parts = dt2_partitions,
++ .nr_parts = ARRAY_SIZE(dt2_partitions)
++};
++
++static struct resource dt2_nor_flash_resource = {
++ .flags = IORESOURCE_MEM,
++ .start = DT2_NOR_BOOT_BASE,
++ .end = DT2_NOR_BOOT_BASE + DT2_NOR_BOOT_SIZE - 1,
++};
++
++static struct platform_device dt2_nor_flash = {
++ .name = "physmap-flash",
++ .id = 0,
++ .dev = {
++ .platform_data = &dt2_nor_flash_data,
++ },
++ .resource = &dt2_nor_flash_resource,
++ .num_resources = 1,
++};
++
++/*****************************************************************************
++ * PCI
++ ****************************************************************************/
++
++void __init dt2_pci_preinit(void)
++{
++ int pin, irq;
++
++ /*
++ * Configure PCI GPIO IRQ pins
++ */
++ pin = DT2_PCI_SLOT0_IRQ_A_PIN;
++ if (gpio_request(pin, "PCI IntA") == 0) {
++ if (gpio_direction_input(pin) == 0) {
++ irq = gpio_to_irq(pin);
++ irq_set_irq_type(irq, IRQ_TYPE_LEVEL_LOW);
++ printk (KERN_INFO "PCI IntA IRQ: %d\n", irq);
++ } else {
++ printk(KERN_ERR "dt2_pci_preinit failed to "
++ "irq_set_irq_type pin %d\n", pin);
++ gpio_free(pin);
++ }
++ } else {
++ printk(KERN_ERR "dt2_pci_preinit failed to request gpio %d\n", pin);
++ }
++
++ pin = DT2_PCI_SLOT0_IRQ_B_PIN;
++ if (gpio_request(pin, "PCI IntB") == 0) {
++ if (gpio_direction_input(pin) == 0) {
++ irq = gpio_to_irq(pin);
++ irq_set_irq_type(irq, IRQ_TYPE_LEVEL_LOW);
++ printk (KERN_INFO "PCI IntB IRQ: %d\n", irq);
++ } else {
++ printk(KERN_ERR "dt2_pci_preinit failed to "
++ "irq_set_irq_type pin %d\n", pin);
++ gpio_free(pin);
++ }
++ } else {
++ printk(KERN_ERR "dt2_pci_preinit failed to gpio_request %d\n", pin);
++ }
++}
++
++static int __init dt2_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
++{
++ int irq;
++
++ /*
++ * Check for devices with hard-wired IRQs.
++ */
++ irq = orion5x_pci_map_irq(dev, slot, pin);
++ if (irq != -1){
++ printk(KERN_INFO "orion5x_pci_map_irq: %d\n", irq);
++ return irq;
++ }
++
++ /*
++ * PCI IRQs are connected via GPIOs
++ */
++ switch (slot - DT2_PCI_SLOT0_OFFS) {
++ case 0:
++ if (pin == 1){
++ irq = gpio_to_irq(DT2_PCI_SLOT0_IRQ_A_PIN);
++ printk(KERN_INFO "dt2_pci_map_irq DT2_PCI_SLOT0_IRQ_A_PIN: %d\n", irq);
++ }
++ else {
++ irq = gpio_to_irq(DT2_PCI_SLOT0_IRQ_B_PIN);
++ printk(KERN_INFO "dt2_pci_map_irq DT2_PCI_SLOT0_IRQ_B_PIN: %d\n", irq);
++ }
++ default:
++ irq = -1;
++ printk(KERN_INFO "dt2_pci_map_irq IRQ: %d\n", irq);
++ }
++
++ return irq;
++}
++
++static struct hw_pci dt2_pci __initdata = {
++ .nr_controllers = 2,
++ .preinit = dt2_pci_preinit,
++ .setup = orion5x_pci_sys_setup,
++ .scan = orion5x_pci_sys_scan_bus,
++ .map_irq = dt2_pci_map_irq,
++};
++
++static int __init dt2_pci_init(void)
++{
++ if (machine_is_dt2())
++ pci_common_init(&dt2_pci);
++
++ return 0;
++}
++
++subsys_initcall(dt2_pci_init);
++
++/*****************************************************************************
++ * Ethernet
++ ****************************************************************************/
++
++static struct mv643xx_eth_platform_data dt2_eth_data = {
++ .phy_addr = MV643XX_ETH_PHY_NONE,
++ .speed = SPEED_1000,
++ .duplex = DUPLEX_FULL,
++};
++
++static struct dsa_chip_data dt2_switch_chip_data = {
++ .port_names[0] = "wan",
++ .port_names[1] = "lan1",
++ .port_names[2] = "lan2",
++ .port_names[3] = "cpu",
++ .port_names[4] = "lan3",
++ .port_names[5] = "lan4",
++};
++
++static struct dsa_platform_data dt2_switch_plat_data = {
++ .nr_chips = 1,
++ .chip = &dt2_switch_chip_data,
++};
++
++/*****************************************************************************
++ * RTC ISL1208 on I2C bus
++ ****************************************************************************/
++static struct i2c_board_info __initdata dt2_i2c_rtc = {
++ I2C_BOARD_INFO("isl1208", 0x6F),
++};
++
++/*****************************************************************************
++ * Sata
++ ****************************************************************************/
++static struct mv_sata_platform_data dt2_sata_data = {
++ .n_ports = 2,
++};
++
++/*****************************************************************************
++ * General Setup
++ ****************************************************************************/
++static unsigned int dt2_mpp_modes[] __initdata = {
++ MPP0_GPIO, // RTC interrupt
++ MPP1_GPIO, // 88e6131 interrupt
++ MPP2_GPIO, // PCI_intB
++ MPP3_GPIO, // PCI_intA
++ MPP4_GPIO, // reset button switch
++ MPP5_GPIO,
++ MPP6_GPIO,
++ MPP7_GPIO,
++ MPP8_GPIO,
++ MPP9_GIGE, /* GE_RXERR */
++ MPP10_GPIO, // usb
++ MPP11_GPIO, // usb
++ MPP12_GIGE, // GE_TXD[4]
++ MPP13_GIGE, // GE_TXD[5]
++ MPP14_GIGE, // GE_TXD[6]
++ MPP15_GIGE, // GE_TXD[7]
++ MPP16_GIGE, // GE_RXD[4]
++ MPP17_GIGE, // GE_RXD[5]
++ MPP18_GIGE, // GE_RXD[6]
++ MPP19_GIGE, // GE_RXD[7]
++ 0,
++};
++
++/*****************************************************************************
++ * LEDS
++ ****************************************************************************/
++static struct platform_device dt2_leds = {
++ .name = "dt2-led",
++ .id = -1,
++};
++
++/****************************************************************************
++ * GPIO key
++ ****************************************************************************/
++static irqreturn_t dt2_reset_handler(int irq, void *dev_id)
++{
++ /* This is the paper-clip reset which does an emergency reboot. */
++ printk(KERN_INFO "Restarting system.\n");
++ machine_restart(NULL);
++
++ /* This should never be reached. */
++ return IRQ_HANDLED;
++}
++
++static irqreturn_t dt2_power_handler(int irq, void *dev_id)
++{
++ printk(KERN_INFO "Shutting down system.\n");
++ machine_power_off();
++ return IRQ_HANDLED;
++}
++
++static void __init dt2_init(void)
++{
++ /*
++ * Setup basic Orion functions. Need to be called early.
++ */
++ orion5x_init();
++
++ orion5x_mpp_conf(dt2_mpp_modes);
++
++ /*
++ * Configure peripherals.
++ */
++
++ orion5x_uart0_init();
++ orion5x_ehci0_init();
++ orion5x_ehci1_init();
++ orion5x_i2c_init();
++ orion5x_sata_init(&dt2_sata_data);
++ orion5x_xor_init();
++
++ printk(KERN_INFO "U-Boot parameters:\n");
++ printk(KERN_INFO "Sys Clk = %d, Tclk = %d, BoardID = 0x%02x\n", mvSysclk, mvTclk, gBoardId);
++
++ printk(KERN_INFO "Serial: %s\n", dt2_eeprom.fc.dt2_serial_number);
++ printk(KERN_INFO "Revision: %016x\n", dt2_eeprom.fc.dt2_revision);
++ printk(KERN_INFO "DT2: Using MAC address %pM for port 0\n",
++ dt2_eeprom.gw.mac_addr[0]);
++ printk(KERN_INFO "DT2: Using MAC address %pM for port 1\n",
++ dt2_eeprom.gw.mac_addr[1]);
++
++ orion5x_eth_init(&dt2_eth_data);
++ memcpy(dt2_eth_data.mac_addr, dt2_eeprom.gw.mac_addr[0], 6);
++ orion5x_eth_switch_init(&dt2_switch_plat_data, NO_IRQ);
++
++ i2c_register_board_info(0, &dt2_i2c_rtc, 1);
++
++ mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
++ ORION_MBUS_DEVBUS_BOOT_ATTR,
++ DT2_NOR_BOOT_BASE, DT2_NOR_BOOT_SIZE);
++
++ platform_device_register(&dt2_nor_flash);
++
++ mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_TARGET(0),
++ ORION_MBUS_DEVBUS_ATTR(0),
++ DT2_LEDS_BASE, DT2_LEDS_SIZE);
++ platform_device_register(&dt2_leds);
++
++ if (request_irq(gpio_to_irq(DT2_PIN_GPIO_RESET), &dt2_reset_handler,
++ IRQF_TRIGGER_LOW,
++ "DT2: Reset button", NULL) < 0) {
++
++ printk("DT2: Reset Button IRQ %d not available\n",
++ gpio_to_irq(DT2_PIN_GPIO_RESET));
++ }
++
++ if (request_irq(gpio_to_irq(DT2_PIN_GPIO_POWER), &dt2_power_handler,
++ IRQF_TRIGGER_LOW,
++ "DT2: Power button", NULL) < 0) {
++
++ printk(KERN_DEBUG "DT2: Power Button IRQ %d not available\n",
++ gpio_to_irq(DT2_PIN_GPIO_POWER));
++ }
++}
++
++static int __init parse_tag_dt2_uboot(const struct tag *t)
++{
++ struct tag_mv_uboot *mv_uboot;
++
++ // Get pointer to our block
++ mv_uboot = (struct tag_mv_uboot*)&t->u;
++ mvTclk = mv_uboot->tclk;
++ mvSysclk = mv_uboot->sysclk;
++ mvUbootVer = mv_uboot->uboot_version;
++ mvIsUsbHost = mv_uboot->isUsbHost;
++
++ // Some clock fixups
++ if(mvTclk == 166000000) mvTclk = 166666667;
++ else if(mvTclk == 133000000) mvTclk = 133333333;
++ else if(mvSysclk == 166000000) mvSysclk = 166666667;
++
++ gBoardId = (mvUbootVer & 0xff);
++
++ //DT2 specific data
++ memcpy(&dt2_eeprom, mv_uboot->dt2_eeprom, sizeof(struct DT2_EEPROM_STRUCT));
++
++ return 0;
++}
++__tagtable(ATAG_MV_UBOOT, parse_tag_dt2_uboot);
++
++/*
++ * This is OpenWrt specific fixup. It includes code from original "tag_fixup_mem32" to
++ * fixup bogus memory tags and also fixes kernel cmdline by adding " init=/etc/preinit"
++ * at the end. It is important to flash OpenWrt image from original Freecom firmware.
++ *
++ * Vanilla kernel should use "tag_fixup_mem32" function.
++ */
++static void __init openwrt_fixup(struct tag *t, char **from)
++{
++ char *p = NULL;
++ static char openwrt_init_tag[] __initdata = " init=/etc/preinit";
++
++ for (; t->hdr.size; t = tag_next(t)){
++ /* Locate the Freecom cmdline */
++ if (t->hdr.tag == ATAG_CMDLINE) {
++ p = t->u.cmdline.cmdline;
++ printk("%s(%d): Found cmdline '%s' at 0x%0lx\n",
++ __FUNCTION__, __LINE__, p, (unsigned long)p);
++ }
++ /*
++ * Many orion-based systems have buggy bootloader implementations.
++ * This is a common fixup for bogus memory tags.
++ */
++ if (t->hdr.tag == ATAG_MEM &&
++ (!t->u.mem.size || t->u.mem.size & ~PAGE_MASK ||
++ t->u.mem.start & ~PAGE_MASK)) {
++ printk(KERN_WARNING
++ "Clearing invalid memory bank %dKB at 0x%08x\n",
++ t->u.mem.size / 1024, t->u.mem.start);
++ t->hdr.tag = 0;
++ }
++ }
++
++ printk("%s(%d): End of table at 0x%0lx\n", __FUNCTION__, __LINE__, (unsigned long)t);
++
++ /* Overwrite the end of the table with a new cmdline tag. */
++ t->hdr.tag = ATAG_CMDLINE;
++ t->hdr.size =
++ (sizeof (struct tag_header) +
++ strlen(p) + strlen(openwrt_init_tag) + 1 + 4) >> 2;
++
++ strlcpy(t->u.cmdline.cmdline, p, COMMAND_LINE_SIZE);
++ strlcpy(t->u.cmdline.cmdline + strlen(p), openwrt_init_tag,
++ COMMAND_LINE_SIZE - strlen(p));
++
++ printk("%s(%d): New cmdline '%s' at 0x%0lx\n",
++ __FUNCTION__, __LINE__,
++ t->u.cmdline.cmdline, (unsigned long)t->u.cmdline.cmdline);
++
++ t = tag_next(t);
++
++ printk("%s(%d): New end of table at 0x%0lx\n", __FUNCTION__, __LINE__, (unsigned long)t);
++
++ t->hdr.tag = ATAG_NONE;
++ t->hdr.size = 0;
++}
++
++/* Warning: Freecom uses their own custom bootloader with mach-type (=1500) */
++MACHINE_START(DT2, "Freecom DataTank Gateway")
++ /* Maintainer: Zintis Petersons <Zintis.Petersons at abcsolutions.lv> */
++ .atag_offset = 0x100,
++ .init_machine = dt2_init,
++ .map_io = orion5x_map_io,
++ .init_irq = orion5x_init_irq,
++ .init_time = orion5x_timer_init,
++ .fixup = openwrt_fixup, //tag_fixup_mem32,
++MACHINE_END
diff --git a/target/linux/orion/patches-4.4/210-wn802t_support.patch b/target/linux/orion/patches-4.4/210-wn802t_support.patch
new file mode 100644
index 000000000000..e7827edd29eb
--- /dev/null
+++ b/target/linux/orion/patches-4.4/210-wn802t_support.patch
@@ -0,0 +1,75 @@
+--- a/arch/arm/mach-orion5x/Kconfig
++++ b/arch/arm/mach-orion5x/Kconfig
+@@ -147,10 +147,13 @@ config MACH_MSS2_DT
+ Maxtor Shared Storage II platform.
+
+ config MACH_WNR854T
+- bool "Netgear WNR854T"
++ bool "Netgear WNR854T / WN802T"
+ help
+ Say 'Y' here if you want your kernel to support the
+- Netgear WNR854T platform.
++ Netgear WNR854T or WN802T platform.
++
++config MACH_WN802T
++ def_bool MACH_WNR854T
+
+ config MACH_RD88F5181L_GE
+ bool "Marvell Orion-VoIP GE Reference Design"
+--- a/arch/arm/mach-orion5x/wnr854t-setup.c
++++ b/arch/arm/mach-orion5x/wnr854t-setup.c
+@@ -115,6 +115,15 @@ static struct dsa_platform_data wnr854t_
+ .chip = &wnr854t_switch_chip_data,
+ };
+
++static struct dsa_chip_data wn802t_switch_chip_data = {
++ .port_names[2] = "wan",
++ .port_names[3] = "cpu",
++};
++
++static struct dsa_platform_data wn802t_switch_plat_data = {
++ .nr_chips = 1,
++ .chip = &wn802t_switch_chip_data,
++};
+ static void __init wnr854t_init(void)
+ {
+ /*
+@@ -128,7 +137,12 @@ static void __init wnr854t_init(void)
+ * Configure peripherals.
+ */
+ orion5x_eth_init(&wnr854t_eth_data);
+- orion5x_eth_switch_init(&wnr854t_switch_plat_data, NO_IRQ);
++
++ if (machine_is_wn802t())
++ orion5x_eth_switch_init(&wn802t_switch_plat_data, NO_IRQ);
++ else
++ orion5x_eth_switch_init(&wnr854t_switch_plat_data, NO_IRQ);
++
+ orion5x_uart0_init();
+
+ mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
+@@ -168,7 +182,7 @@ static struct hw_pci wnr854t_pci __initd
+
+ static int __init wnr854t_pci_init(void)
+ {
+- if (machine_is_wnr854t())
++ if (machine_is_wnr854t() || machine_is_wn802t())
+ pci_common_init(&wnr854t_pci);
+
+ return 0;
+@@ -186,3 +200,15 @@ MACHINE_START(WNR854T, "Netgear WNR854T"
+ .fixup = tag_fixup_mem32,
+ .restart = orion5x_restart,
+ MACHINE_END
++
++MACHINE_START(WN802T, "Netgear WN802T")
++ /* Maintainer: Imre Kaloz <kaloz at openwrt.org> */
++ .atag_offset = 0x100,
++ .init_machine = wnr854t_init,
++ .map_io = orion5x_map_io,
++ .init_early = orion5x_init_early,
++ .init_irq = orion5x_init_irq,
++ .init_time = orion5x_timer_init,
++ .fixup = tag_fixup_mem32,
++ .restart = orion5x_restart,
++MACHINE_END
--
2.10.2
More information about the Lede-dev
mailing list