[LEDE-DEV] [PATCH 0/9] lantiq: VGV7519 fixes

[Eddi De Pieri]

Hi  Mathias,

Just tried to boot a ramimage from tftp on vgv7519:

On my board:
Bytes transferred = 7084442 (6c199a hex)
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-3.10.49
   Created:      2014-11-11  17:40:00 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    7084378 Bytes = 6.8 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... LZMA: uncompress or overwrite error
7 - must RESET b
ROM VER: 1.0.5
CFG 01

Any idea on how to fix this issue?
Does you see it on other board?

Regards

On Thu, May 26, 2016 at 11:07 PM, Mathias Kresin <dev at kresin.me> wrote:
> Beside cleaning up the device tree source file, this patch series fixes
> the following issues:
>
> - second usb doesn't work
> - switch not recognized by swconfig/no vlans
> - no working UART bootable u-boot available
> - only binary u-boot available/self compiled u-boot to big for partition
>
> The last remaining issue that couldn't be fixed so far, are three leds
> which do not blink on network tx/rx with the R01 revision of the
> VGV7519.
>
> This is related to a known bug of PEF 7071 v1.3 firmware. The firmware
> counts the packages but doesn't trigger the led. To workaround the
> issue it would be required to transfer control of the leds to the
> switch by enabling the LED Externally Controlled Mode (ECM) of the phys.
>
> All patches have been tested during the last weeks by the OpenWrt Forum
> users pe0fko and especially Timeless with both revision of the VGV7519.
>
> Mathias Kresin (9):
>   lantiq: VGV7519 - remove/merge redundant parts in dts
>   lantiq: VGV7519 - cleanup pinmux configuration
>   lantiq: VGV7519 - add second usb port
>   lantiq: VGV7519 - add vlan support
>   lantiq: VGV7519 - get mac address from board_config partition
>   lantiq: VGV7519 - fix brn partition layout
>   uboot-lantiq: vrx200 - add support for dual nor flash
>   uboot-lantiq: vrx200 - lzma compress gphy firmware
>   uboot-lantiq: Add Arcadyan VGV7519 support
>
>  package/boot/uboot-lantiq/Makefile                 |  35 ++-
>  ...014-MIPS-add-support-for-Lantiq-XWAY-SoCs.patch |  74 ++++--
>  .../0021-MIPS-vrx200-add-NAND-SPL-support.patch    |   2 +-
>  ...PS-add-board-support-for-Arcadyan-VGV7519.patch | 288 +++++++++++++++++++++
>  .../linux/lantiq/base-files/etc/board.d/02_network |   3 +-
>  target/linux/lantiq/dts/VGV7519.dtsi               |  83 +++---
>  target/linux/lantiq/dts/VGV7519BRN.dts             |  65 +++--
>  target/linux/lantiq/dts/VGV7519NOR.dts             |  18 --
>  8 files changed, 450 insertions(+), 118 deletions(-)
>  create mode 100644 package/boot/uboot-lantiq/patches/0114-MIPS-add-board-support-for-Arcadyan-VGV7519.patch
>
> --
> 1.9.1
>