[LEDE-DEV] [PATCHv3 1/1] [brcm63xx] Add initial support for EVG2000
Xotic750
xotic750 at gmail.com
Sun May 22 15:56:23 PDT 2016
From: Graham Fairweather <xotic750 at gmail.com>
This patch adds support for the Netgear EVG2000 VoIP Gateway to the
bcm63xx targets.
Ran 'make target/linux/refresh V=s' after update to kernel 4.4.10 from
4.4.8 where the initial patch was added.
This device was not sold to the general public, but rather is/was
provided by telcos to customers in Sweden, Australia, Singapore and
other parts of asia.
System-On-Chip: Broadcom BCM6369 (2 * BMIPS4350 v3.1 / 400 MHz)
Flash size: 16 MiB
RAM size: 64 MiB
Wireless: BCM4322 802.11b/g/n (onboard)
Ethernet: Broadcom BCM53115
USB: 2 x USB 2.0
Known issues:
- Unable to detect 53115 switch. This appear to be a problem with
probing for the PHY using MDIO and results in error 5. Doesn't seem to
be a problem with the configuration, and could use someone with
experience to have a look at it.
- Uses the b43 driver as using the OpenWRT/LEDE broadcom-wl driver
fails to load the firmware for the 4322, so 802.11n is not supported.
The factory build uses a newer broadcom-wl driver.
- No support for the 2 VoIP ports (not attempted)
More info on the device and the research can be found at:
https://wiki.openwrt.org/toh/netgear/evg2000
https://wikidevi.com/wiki/Netgear_EVG2000
https://github.com/Xotic750/mirror-lede/tree/evg2000
https://forum.openwrt.org/viewtopic.php?id=63950
Signed-off-by: Graham Fairweather <xotic750 at gmail.com>
---
.../linux/brcm63xx/base-files/etc/board.d/01_leds | 7 ++
.../brcm63xx/base-files/etc/board.d/02_network | 1 +
target/linux/brcm63xx/base-files/etc/diag.sh | 3 +
.../base-files/etc/uci-defaults/09_fix_crc | 2 +-
target/linux/brcm63xx/base-files/lib/brcm63xx.sh | 3 +
.../lib/preinit/05_init_interfaces_brcm63xx | 1 +
target/linux/brcm63xx/dts/evg2000.dts | 103 +++++++++++++++++++++
target/linux/brcm63xx/image/Makefile | 2 +
.../brcm63xx/patches-4.1/575-board_EVG2000.patch | 62 +++++++++++++
...-m25p80-use-parsers-if-provided-in-flash-.patch | 2 +-
...CES-m25p80-add-support-for-limiting-reads.patch | 4 +-
.../414-MTD-m25p80-allow-passing-pp_data.patch | 2 +-
.../brcm63xx/patches-4.4/575-board_EVG2000.patch | 62 +++++++++++++
target/linux/brcm63xx/profiles/netgear.mk | 10 ++
14 files changed, 259 insertions(+), 5 deletions(-)
create mode 100644 target/linux/brcm63xx/dts/evg2000.dts
create mode 100644 target/linux/brcm63xx/patches-4.1/575-board_EVG2000.patch
create mode 100644 target/linux/brcm63xx/patches-4.4/575-board_EVG2000.patch
diff --git a/target/linux/brcm63xx/base-files/etc/board.d/01_leds b/target/linux/brcm63xx/base-files/etc/board.d/01_leds
index 8339254..4163214 100755
--- a/target/linux/brcm63xx/base-files/etc/board.d/01_leds
+++ b/target/linux/brcm63xx/base-files/etc/board.d/01_leds
@@ -24,6 +24,13 @@ dgnd3700v1_dgnd3800b)
ucidef_set_led_usbdev "usb1" "USB1" "DGND3700v1_3800B:green:usb-back" "1-1"
ucidef_set_led_usbdev "usb2" "USB2" "DGND3700v1_3800B:green:usb-front" "1-2"
;;
+evg2000)
+ ucidef_set_led_netdev "lan" "LAN" "EVG2000:green:lan" "eth0"
+ ucidef_set_led_netdev "wan" "WAN" "EVG2000:green:wan" "eth1"
+ ucidef_set_led_netdev "wlan0" "WIFI" "EVG2000:green:wireless" "wlan0"
+ ucidef_set_led_usbdev "usb1" "USB1" "EVG2000:green:voip1" "1-1"
+ ucidef_set_led_usbdev "usb2" "USB2" "EVG2000:green:voip2" "1-2"
+ ;;
fast2704n)
ucidef_set_led_netdev "wan" "WAN" "F at ST2704N:green:inet" "eth0.2"
;;
diff --git a/target/linux/brcm63xx/base-files/etc/board.d/02_network b/target/linux/brcm63xx/base-files/etc/board.d/02_network
index f96da08..83367c1 100755
--- a/target/linux/brcm63xx/base-files/etc/board.d/02_network
+++ b/target/linux/brcm63xx/base-files/etc/board.d/02_network
@@ -11,6 +11,7 @@ board_config_update
case "$(brcm63xx_board_name)" in
cvg834g |\
+evg2000 |\
rta770bw |\
rta770w |\
spw303v |\
diff --git a/target/linux/brcm63xx/base-files/etc/diag.sh b/target/linux/brcm63xx/base-files/etc/diag.sh
index b864964..6ac2459 100644
--- a/target/linux/brcm63xx/base-files/etc/diag.sh
+++ b/target/linux/brcm63xx/base-files/etc/diag.sh
@@ -70,6 +70,9 @@ set_state() {
dgnd3700v1_dgnd3800b)
status_led="DGND3700v1_3800B:green:power"
;;
+ evg2000)
+ status_led="EVG2000:green:power"
+ ;;
fast2504n)
status_led="fast2504n:green:ok"
;;
diff --git a/target/linux/brcm63xx/base-files/etc/uci-defaults/09_fix_crc b/target/linux/brcm63xx/base-files/etc/uci-defaults/09_fix_crc
index 70dbe2a..1201168 100644
--- a/target/linux/brcm63xx/base-files/etc/uci-defaults/09_fix_crc
+++ b/target/linux/brcm63xx/base-files/etc/uci-defaults/09_fix_crc
@@ -21,6 +21,7 @@ case "$(brcm63xx_board_name)" in
cpva642 |\
ct-6373 |\
dsl-274xb-f |\
+ evg2000 |\
hg622 |\
magic |\
p870hw-51a_v2 |\
@@ -37,4 +38,3 @@ case "$(brcm63xx_board_name)" in
do_fixcrc
;;
esac
-
diff --git a/target/linux/brcm63xx/base-files/lib/brcm63xx.sh b/target/linux/brcm63xx/base-files/lib/brcm63xx.sh
index a2d6519..9cc0b2b 100755
--- a/target/linux/brcm63xx/base-files/lib/brcm63xx.sh
+++ b/target/linux/brcm63xx/base-files/lib/brcm63xx.sh
@@ -183,6 +183,9 @@ brcm63xx_dt_detect() {
"Netgear DGND3700v1/DGND3800B")
board_name="dgnd3700v1_dgnd3800b"
;;
+ "Netgear EVG2000")
+ board_name="evg2000"
+ ;;
"NuCom R5010UN v2")
board_name="r5010un_v2"
;;
diff --git a/target/linux/brcm63xx/base-files/lib/preinit/05_init_interfaces_brcm63xx b/target/linux/brcm63xx/base-files/lib/preinit/05_init_interfaces_brcm63xx
index 7e4dfcb..1e3fc14 100644
--- a/target/linux/brcm63xx/base-files/lib/preinit/05_init_interfaces_brcm63xx
+++ b/target/linux/brcm63xx/base-files/lib/preinit/05_init_interfaces_brcm63xx
@@ -18,6 +18,7 @@ set_preinit_iface() {
dsl-274xb-c |\
dsl-274xb-f |\
dsl-275xb-d |\
+ evg2000 |\
fast2504n |\
fast2704v2 |\
hg553 |\
diff --git a/target/linux/brcm63xx/dts/evg2000.dts b/target/linux/brcm63xx/dts/evg2000.dts
new file mode 100644
index 0000000..04f7b84
--- /dev/null
+++ b/target/linux/brcm63xx/dts/evg2000.dts
@@ -0,0 +1,103 @@
+/dts-v1/;
+
+#include "bcm6368.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Netgear EVG2000";
+ compatible = "netgear,evg2000", "brcm,bcm6368";
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+ debounce-interval = <60>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 25 1>;
+ linux,code = <KEY_RESTART>;
+ };
+ wps {
+ label = "wps";
+ gpios = <&gpio0 26 1>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ voip1_green {
+ label = "EVG2000:green:voip1";
+ gpios = <&gpio0 14 1>;
+ };
+ voip2_green {
+ label = "EVG2000:green:voip2";
+ gpios = <&gpio0 2 1>;
+ };
+ inet_red {
+ label = "EVG2000:red:inet";
+ gpios = <&gpio0 4 1>;
+ };
+ inet_green {
+ label = "EVG2000:green:inet";
+ gpios = <&gpio0 5 1>;
+ };
+ usb_green {
+ label = "EVG2000:green:usb";
+ gpios = <&gpio0 15 1>;
+ };
+ power_green {
+ label = "EVG2000:green:power";
+ gpios = <&gpio0 22 1>;
+ default-state = "on";
+ };
+ power_red {
+ label = "EVG2000:red:power";
+ gpios = <&gpio0 23 1>;
+ };
+ lan_green {
+ label = "EVG2000:green:lan";
+ gpios = <&gpio0 24 1>;
+ };
+ wireless_green {
+ label = "EVG2000:green:wireless";
+ gpios = <&gpio0 26 1>;
+ };
+ wan_green {
+ label = "EVG2000:green:wan";
+ gpios = <&gpio0 27 1>;
+ };
+ };
+};
+
+&pflash {
+ status = "ok";
+
+ linux,part-probe = "bcm63xxpart";
+
+ cfe at 0 {
+ label = "CFE";
+ reg = <0x00000000 0x00020000>;
+ read-only;
+ };
+
+ linux at 20000 {
+ label = "linux";
+ reg = <0x00020000 0x00f40000>;
+ };
+
+ board_data at f60000 {
+ label = "board_data";
+ reg = <0x00f60000 0x00080000>;
+ read-only;
+ };
+
+ nvram at fe0000 {
+ label = "nvram";
+ reg = <0x00fe0000 0x00020000>;
+ };
+};
diff --git a/target/linux/brcm63xx/image/Makefile b/target/linux/brcm63xx/image/Makefile
index e00b6fb..f1fb86b 100644
--- a/target/linux/brcm63xx/image/Makefile
+++ b/target/linux/brcm63xx/image/Makefile
@@ -593,6 +593,8 @@ $(eval $(call bcm63xxCfeRamdisk,DG834GV4,DG834GTv4,dg834g_v4,96348W3,6348))
$(eval $(call bcm63xxCfeNetgear,DGND3700v1_3800B,DGND3700v1,dgnd3700v1,96368MVWG,6368,--image-offset 0x20000 --block-size 0x20000,U12L144T01_NETGEAR_NEWLED,1))
# Netgear DGND3800B
$(eval $(call bcm63xxCfeNetgear,DGND3700v1_3800B,DGND3800B,dgnd3700v1,96368MVWG,6368,--image-offset 0x20000 --block-size 0x20000,U12L144T11_NETGEAR_NEWLED,1))
+# Netgear EVG2000
+$(eval $(call bcm63xxCfeNetgear,EVG2000,EVG2000,evg2000,96369PVG,6369,--image-offset 0x20000 --block-size 0x20000,U12H154T90_NETGEAR,1))
# NuCom R5010UNv2
$(eval $(call bcm63xxCfe,R5010UNV2,R5010UNv2,r5010unv2,96328ang,6328,--pad 8))
# Pirelli Alice Gate VoIP 2 Plus Wi-Fi AGPF-S0
diff --git a/target/linux/brcm63xx/patches-4.1/575-board_EVG2000.patch b/target/linux/brcm63xx/patches-4.1/575-board_EVG2000.patch
new file mode 100644
index 0000000..9339085
--- /dev/null
+++ b/target/linux/brcm63xx/patches-4.1/575-board_EVG2000.patch
@@ -0,0 +1,62 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -2010,6 +2010,43 @@ static struct board_info __initdata boar
+ .num_spis = ARRAY_SIZE(DGND3700v1_3800B_spi_devices),
+ };
+
++static struct sprom_fixup __initdata EVG2000_fixups[] = {
++ { .offset = 219, .value = 0xec08 },
++};
++
++static struct board_info __initdata board_EVG2000 = {
++ .name = "96369PVG",
++ .expected_cpu_id = 0x6368,
++
++ .has_uart0 = 1,
++ .has_pci = 1,
++ .has_ohci0 = 1,
++ .has_ehci0 = 1,
++ .num_usbh_ports = 2,
++
++ .has_enetsw = 1,
++ .enetsw = {
++ .used_ports = {
++ [5] = {
++ .used = 1,
++ .phy_id = 0xff,
++ .bypass_link = 1,
++ .force_speed = 1000,
++ .force_duplex_full = 1,
++ .name = "RGMII",
++ },
++ },
++ },
++ .use_fallback_sprom = 1,
++ .fallback_sprom = {
++ .type = SPROM_BCM4322,
++ .pci_bus = 0,
++ .pci_dev = 1,
++ .board_fixups = EVG2000_fixups,
++ .num_board_fixups = ARRAY_SIZE(EVG2000_fixups),
++ },
++};
++
+ static struct board_info __initdata board_HG655b = {
+ .name = "HW65x",
+ .expected_cpu_id = 0x6368,
+@@ -2610,6 +2647,7 @@ static const struct board_info __initcon
+ &board_96368mvwg,
+ &board_96368mvngr,
+ &board_DGND3700v1_3800B,
++ &board_EVG2000,
+ &board_HG622,
+ &board_HG655b,
+ &board_P870HW51A_V2,
+@@ -2722,6 +2760,7 @@ static struct of_device_id const bcm963x
+ { .compatible = "huawei,hg622", .data = &board_HG622, },
+ { .compatible = "huawei,hg655b", .data = &board_HG655b, },
+ { .compatible = "netgear,dgnd3700v1", .data = &board_DGND3700v1_3800B, },
++ { .compatible = "netgear,evg2000", .data = &board_EVG2000, },
+ { .compatible = "zyxel,p870hw-51a-v2", .data = &board_P870HW51A_V2, },
+ #endif
+ #ifdef CONFIG_BCM63XX_CPU_63268
diff --git a/target/linux/brcm63xx/patches-4.4/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch b/target/linux/brcm63xx/patches-4.4/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch
index be62e67..4793836 100644
--- a/target/linux/brcm63xx/patches-4.4/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch
+++ b/target/linux/brcm63xx/patches-4.4/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch
@@ -11,7 +11,7 @@ Signed-off-by: Jonas Gorski <jonas.gorski at gmail.com>
--- a/drivers/mtd/devices/m25p80.c
+++ b/drivers/mtd/devices/m25p80.c
-@@ -229,7 +229,8 @@ static int m25p_probe(struct spi_device
+@@ -251,7 +251,8 @@ static int m25p_probe(struct spi_device
ppdata.of_node = spi->dev.of_node;
diff --git a/target/linux/brcm63xx/patches-4.4/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch b/target/linux/brcm63xx/patches-4.4/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch
index 3877442..75a874d 100644
--- a/target/linux/brcm63xx/patches-4.4/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch
+++ b/target/linux/brcm63xx/patches-4.4/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch
@@ -28,7 +28,7 @@ Signed-off-by: Jonas Gorski <jonas.gorski at gmail.com>
size_t *retlen, u_char *buf)
{
struct m25p *flash = nor->priv;
-@@ -152,6 +153,29 @@ static int m25p80_read(struct spi_nor *n
+@@ -174,6 +175,29 @@ static int m25p80_read(struct spi_nor *n
return 0;
}
@@ -58,7 +58,7 @@ Signed-off-by: Jonas Gorski <jonas.gorski at gmail.com>
static int m25p80_erase(struct spi_nor *nor, loff_t offset)
{
struct m25p *flash = nor->priv;
-@@ -223,6 +247,9 @@ static int m25p_probe(struct spi_device
+@@ -245,6 +269,9 @@ static int m25p_probe(struct spi_device
else
flash_name = spi->modalias;
diff --git a/target/linux/brcm63xx/patches-4.4/414-MTD-m25p80-allow-passing-pp_data.patch b/target/linux/brcm63xx/patches-4.4/414-MTD-m25p80-allow-passing-pp_data.patch
index e421e9a..bbb565e 100644
--- a/target/linux/brcm63xx/patches-4.4/414-MTD-m25p80-allow-passing-pp_data.patch
+++ b/target/linux/brcm63xx/patches-4.4/414-MTD-m25p80-allow-passing-pp_data.patch
@@ -10,7 +10,7 @@ Subject: [PATCH 64/79] MTD: m25p80: allow passing pp_data
--- a/drivers/mtd/devices/m25p80.c
+++ b/drivers/mtd/devices/m25p80.c
-@@ -250,6 +250,9 @@ static int m25p_probe(struct spi_device
+@@ -272,6 +272,9 @@ static int m25p_probe(struct spi_device
if (data)
flash->max_transfer_len = data->max_transfer_len;
diff --git a/target/linux/brcm63xx/patches-4.4/575-board_EVG2000.patch b/target/linux/brcm63xx/patches-4.4/575-board_EVG2000.patch
new file mode 100644
index 0000000..fc7afc7
--- /dev/null
+++ b/target/linux/brcm63xx/patches-4.4/575-board_EVG2000.patch
@@ -0,0 +1,62 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -2011,6 +2011,43 @@ static struct board_info __initdata boar
+ .num_spis = ARRAY_SIZE(DGND3700v1_3800B_spi_devices),
+ };
+
++static struct sprom_fixup __initdata EVG2000_fixups[] = {
++ { .offset = 219, .value = 0xec08 },
++};
++
++static struct board_info __initdata board_EVG2000 = {
++ .name = "96369PVG",
++ .expected_cpu_id = 0x6368,
++
++ .has_uart0 = 1,
++ .has_pci = 1,
++ .has_ohci0 = 1,
++ .has_ehci0 = 1,
++ .num_usbh_ports = 2,
++
++ .has_enetsw = 1,
++ .enetsw = {
++ .used_ports = {
++ [5] = {
++ .used = 1,
++ .phy_id = 0xff,
++ .bypass_link = 1,
++ .force_speed = 1000,
++ .force_duplex_full = 1,
++ .name = "RGMII",
++ },
++ },
++ },
++ .use_fallback_sprom = 1,
++ .fallback_sprom = {
++ .type = SPROM_BCM4322,
++ .pci_bus = 0,
++ .pci_dev = 1,
++ .board_fixups = EVG2000_fixups,
++ .num_board_fixups = ARRAY_SIZE(EVG2000_fixups),
++ },
++};
++
+ static struct board_info __initdata board_HG655b = {
+ .name = "HW65x",
+ .expected_cpu_id = 0x6368,
+@@ -2611,6 +2648,7 @@ static const struct board_info __initcon
+ &board_96368mvwg,
+ &board_96368mvngr,
+ &board_DGND3700v1_3800B,
++ &board_EVG2000,
+ &board_HG622,
+ &board_HG655b,
+ &board_P870HW51A_V2,
+@@ -2723,6 +2761,7 @@ static struct of_device_id const bcm963x
+ { .compatible = "huawei,hg622", .data = &board_HG622, },
+ { .compatible = "huawei,hg655b", .data = &board_HG655b, },
+ { .compatible = "netgear,dgnd3700v1", .data = &board_DGND3700v1_3800B, },
++ { .compatible = "netgear,evg2000", .data = &board_EVG2000, },
+ { .compatible = "zyxel,p870hw-51a-v2", .data = &board_P870HW51A_V2, },
+ #endif
+ #ifdef CONFIG_BCM63XX_CPU_63268
diff --git a/target/linux/brcm63xx/profiles/netgear.mk b/target/linux/brcm63xx/profiles/netgear.mk
index bc345bb..e3bc34a 100644
--- a/target/linux/brcm63xx/profiles/netgear.mk
+++ b/target/linux/brcm63xx/profiles/netgear.mk
@@ -41,3 +41,13 @@ define Profile/DGND3700v1_3800B/Description
Package set optimized for DGND3700 v1 / DGND3800B.
endef
$(eval $(call Profile,DGND3700v1_3800B))
+
+define Profile/EVG2000
+ NAME:=Netgear EVG2000
+ PACKAGES:=kmod-b43 wpad-mini \
+ kmod-usb2 kmod-usb-ohci kmod-ledtrig-usbdev
+endef
+define Profile/EVG2000/Description
+ Package set optimized for EVG2000.
+endef
+$(eval $(call Profile,EVG2000))
--
2.5.5
More information about the Lede-dev
mailing list