[LEDE-DEV] mmc driver for openwrt on fonera 2100
Marco Castrovilli
marco.castrovilli at gmail.com
Sun Jun 5 17:00:04 PDT 2016
i tried 8.09.2 too.
always the same behaviour: everything is ok until i enable
/etc/init.d/mmc_over_gpio: then network become unstable and i can't get
ssh connection anymore.
:(
Il 05/06/2016 02:02, Marco Castrovilli ha scritto:
> hi andrew. no good news. i flashed again fonera and followed
> instruction of the guide but:
>
> when i try command uci set mmc_over_gpio. at mmc_over_gpio[0].enabled=1 i
> have uci: Entry not found message;
>
> uci is ok: other commands (uci add fstab mount etc. etc) are correctly
> executed;
>
> when i try starting mmc_over_gpio, fonera reboot and connection become
> ustable.
>
> below you can find details.
>
> perhaps does this mean that soldered points are not good? or do i
> forget some fundamental step?
>
> thank you for your opinion.
>
>
> login as: root
> root at 192.168.1.1's password:
>
>
> BusyBox v1.11.2 (2009-01-05 06:34:55 CET) built-in shell (ash)
> Enter 'help' for a list of built-in commands.
>
> _______ ________ __
> | |.-----.-----.-----.| | | |.----.| |_
> | - || _ | -__| || | | || _|| _|
> |_______|| __|_____|__|__||________||__| |____|
> |__| W I R E L E S S F R E E D O M
> KAMIKAZE (8.09, r14511) ----------------------------
> * 10 oz Vodka Shake well with ice and strain
> * 10 oz Triple sec mixture into 10 shot glasses.
> * 10 oz lime juice Salute!
> ---------------------------------------------------
> root at OpenWrt:~# free
> total used free shared buffers
> Mem: 13688 7808 5880 0 0
> Swap: 0 0 0
> Total: 13688 7808 5880
> root at OpenWrt:~# ping 192.168.1.171
> PING 192.168.1.171 (192.168.1.171): 56 data bytes
> 64 bytes from 192.168.1.171: seq=0 ttl=128 time=3.857 ms
> 64 bytes from 192.168.1.171: seq=1 ttl=128 time=3.451 ms
> 64 bytes from 192.168.1.171: seq=2 ttl=128 time=2.674 ms
> 64 bytes from 192.168.1.171: seq=3 ttl=128 time=6.248 ms
> 64 bytes from 192.168.1.171: seq=4 ttl=128 time=3.290 ms
> ^C
> --- 192.168.1.171 ping statistics ---
> 5 packets transmitted, 5 packets received, 0% packet loss
> round-trip min/avg/max = 2.674/3.904/6.248 ms
> root at OpenWrt:~# ping www.google.it
> ping: bad address 'www.google.it'
> root at OpenWrt:~# cat /etc/resolv.conf
> nameserver 127.0.0.1
> root at OpenWrt:~# cat /etc/config/network
> # Copyright (C) 2006 OpenWrt.org
>
> config interface loopback
> option ifname lo
> option proto static
> option ipaddr 127.0.0.1
> option netmask 255.0.0.0
>
> config interface lan
> option ifname eth0
> option type bridge
> option proto static
> option ipaddr 192.168.1.1
> option netmask 255.255.255.0
> root at OpenWrt:~# cat /etc/resolv.conf
> nameserver 127.0.0.1
> root at OpenWrt:~# cat /etc/config/network
>
> config 'interface' 'loopback'
> option 'ifname' 'lo'
> option 'proto' 'static'
> option 'ipaddr' '127.0.0.1'
> option 'netmask' '255.0.0.0'
>
> config 'interface' 'lan'
> option 'ifname' 'eth0'
> option 'type' 'bridge'
> option 'proto' 'static'
> option 'ipaddr' '192.168.1.1'
> option 'netmask' '255.255.255.0'
> option 'gateway' '192.168.1.254'
> option 'defaultroute' '0'
> option 'peerdns' '0'
> option 'dns' '192.168.1.254'
>
> root at OpenWrt:~# cat /etc/resolv.conf
> nameserver 127.0.0.1
> root at OpenWrt:~# cat /etc/config/network
>
> config 'interface' 'loopback'
> option 'ifname' 'lo'
> option 'proto' 'static'
> option 'ipaddr' '127.0.0.1'
> option 'netmask' '255.0.0.0'
>
> config 'interface' 'lan'
> option 'ifname' 'eth0'
> option 'proto' 'static'
> option 'ipaddr' '192.168.1.1'
> option 'netmask' '255.255.255.0'
> option 'gateway' '192.168.1.254'
> option 'defaultroute' '0'
> option 'peerdns' '0'
> option 'dns' '192.168.1.254'
>
> root at OpenWrt:~# date
> Fri Feb 6 02:13:00 UTC 2009
> root at OpenWrt:~# ping www.google.it
> PING www.google.it (216.58.198.131): 56 data bytes
> 64 bytes from 216.58.198.131: seq=0 ttl=53 time=47.755 ms
> 64 bytes from 216.58.198.131: seq=1 ttl=53 time=48.364 ms
> 64 bytes from 216.58.198.131: seq=2 ttl=53 time=47.934 ms
> 64 bytes from 216.58.198.131: seq=3 ttl=53 time=51.164 ms
> 64 bytes from 216.58.198.131: seq=4 ttl=53 time=47.692 ms
> ^C
> --- www.google.it ping statistics ---
> 5 packets transmitted, 5 packets received, 0% packet loss
> round-trip min/avg/max = 47.692/48.581/51.164 ms
> root at OpenWrt:~# opkg update
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/Packages.gz
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> Packages.gz 100%
> |************************************************************************************************************|
> 143k 00:00:00 ETA
> Inflating
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/Packages.gz
> Updated list of available packages in /var/opkg-lists/snapshots
> root at OpenWrt:~# opkg install kmod-mmc-over-gpio kmod-fs-ext3 cfdisk
> e2fsprogs kmod-nls-base kmod-nls-cp437 kmod-nls-iso8859-1
> Installing kmod-mmc-over-gpio (2.6.26.5-atheros-2) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./kmod-mmc-over-gpio_2.6.26.5-atheros-2_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> kmod-mmc-over-gpio_2 100%
> |************************************************************************************************************|
> 5565 --:--:-- ETA
> Installing kmod-mmc-spi (2.6.26.5-atheros-1) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./kmod-mmc-spi_2.6.26.5-atheros-1_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> kmod-mmc-spi_2.6.26. 100%
> |************************************************************************************************************|
> 7219 --:--:-- ETA
> Installing kmod-mmc (2.6.26.5-atheros-1) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./kmod-mmc_2.6.26.5-atheros-1_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> kmod-mmc_2.6.26.5-at 100%
> |************************************************************************************************************|
> 28898 --:--:-- ETA
> Installing kmod-crc-itu-t (2.6.26.5-atheros-1) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./kmod-crc-itu-t_2.6.26.5-atheros-1_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> kmod-crc-itu-t_2.6.2 100%
> |************************************************************************************************************|
> 2269 --:--:-- ETA
> Installing kmod-crc7 (2.6.26.5-atheros-1) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./kmod-crc7_2.6.26.5-atheros-1_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> kmod-crc7_2.6.26.5-a 100%
> |************************************************************************************************************|
> 1911 --:--:-- ETA
> Installing kmod-spi-gpio (2.6.26.5-atheros-1) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./kmod-spi-gpio_2.6.26.5-atheros-1_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> kmod-spi-gpio_2.6.26 100%
> |************************************************************************************************************|
> 3945 --:--:-- ETA
> Installing kmod-spi-bitbang (2.6.26.5-atheros-1) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./kmod-spi-bitbang_2.6.26.5-atheros-1_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> kmod-spi-bitbang_2.6 100%
> |************************************************************************************************************|
> 3580 --:--:-- ETA
> Installing kmod-fs-ext3 (2.6.26.5-atheros-1) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./kmod-fs-ext3_2.6.26.5-atheros-1_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> kmod-fs-ext3_2.6.26. 100%
> |************************************************************************************************************|
> 92934 00:00:00 ETA
> Installing cfdisk (2.13.0.1-2) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./cfdisk_2.13.0.1-2_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> cfdisk_2.13.0.1-2_mi 100%
> |************************************************************************************************************|
> 28445 --:--:-- ETA
> Installing libncurses (5.6-1) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./libncurses_5.6-1_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> libncurses_5.6-1_mip 100%
> |************************************************************************************************************|
> 135k 00:00:00 ETA
> Installing e2fsprogs (1.40.11-1) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./e2fsprogs_1.40.11-1_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> e2fsprogs_1.40.11-1_ 100%
> |************************************************************************************************************|
> 101k 00:00:00 ETA
> Installing libblkid (1.40.11-1) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./libblkid_1.40.11-1_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> libblkid_1.40.11-1_m 100%
> |************************************************************************************************************|
> 17309 --:--:-- ETA
> Installing libuuid (1.40.11-1) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./libuuid_1.40.11-1_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> libuuid_1.40.11-1_mi 100%
> |************************************************************************************************************|
> 7491 --:--:-- ETA
> Installing libext2fs (1.40.11-1) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./libext2fs_1.40.11-1_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> libext2fs_1.40.11-1_ 100%
> |************************************************************************************************************|
> 195k --:--:-- ETA
> Installing kmod-nls-base (2.6.26.5-atheros-1) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./kmod-nls-base_2.6.26.5-atheros-1_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> kmod-nls-base_2.6.26 100%
> |************************************************************************************************************|
> 3724 --:--:-- ETA
> Installing kmod-nls-cp437 (2.6.26.5-atheros-1) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./kmod-nls-cp437_2.6.26.5-atheros-1_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> kmod-nls-cp437_2.6.2 100%
> |************************************************************************************************************|
> 2977 --:--:-- ETA
> Installing kmod-nls-iso8859-1 (2.6.26.5-atheros-1) to root...
> Downloading
> http://downloads.openwrt.org/kamikaze/8.09/atheros/packages/./kmod-nls-iso8859-1_2.6.26.5-atheros-1_mips.ipk
> Connecting to downloads.openwrt.org (78.24.191.177:80)
> kmod-nls-iso8859-1_2 100%
> |************************************************************************************************************|
> 2650 --:--:-- ETA
> Configuring cfdisk
> Configuring e2fsprogs
> Configuring kmod-crc-itu-t
> Configuring kmod-crc7
> Configuring kmod-fs-ext3
> Configuring kmod-mmc
> Configuring kmod-mmc-over-gpio
> Configuring kmod-mmc-spi
> Configuring kmod-nls-base
> Configuring kmod-nls-cp437
> Configuring kmod-nls-iso8859-1
> Configuring kmod-spi-bitbang
> Configuring kmod-spi-gpio
> Configuring libblkid
> Configuring libext2fs
> Configuring libncurses
> Configuring libuuid
> root at OpenWrt:~#
>
> reboot
>
> login as: root
> root at 192.168.1.1's password:
>
>
> BusyBox v1.11.2 (2009-01-05 06:34:55 CET) built-in shell (ash)
> Enter 'help' for a list of built-in commands.
>
> _______ ________ __
> | |.-----.-----.-----.| | | |.----.| |_
> | - || _ | -__| || | | || _|| _|
> |_______|| __|_____|__|__||________||__| |____|
> |__| W I R E L E S S F R E E D O M
> KAMIKAZE (8.09, r14511) ----------------------------
> * 10 oz Vodka Shake well with ice and strain
> * 10 oz Triple sec mixture into 10 shot glasses.
> * 10 oz lime juice Salute!
> ---------------------------------------------------
> root at OpenWrt:~# ping www.google.it
> PING www.google.it (216.58.214.99): 56 data bytes
> 64 bytes from 216.58.214.99: seq=0 ttl=52 time=49.145 ms
> 64 bytes from 216.58.214.99: seq=1 ttl=52 time=48.823 ms
> 64 bytes from 216.58.214.99: seq=2 ttl=52 time=47.853 ms
> 64 bytes from 216.58.214.99: seq=3 ttl=52 time=48.080 ms
> ^C
> --- www.google.it ping statistics ---
> 4 packets transmitted, 4 packets received, 0% packet loss
> round-trip min/avg/max = 47.853/48.475/49.145 ms
> root at OpenWrt:~# uci set mmc_over_gpio. at mmc_over_gpio[0].enabled=1
> uci: Entry not found
> root at OpenWrt:~# ls /sbin/uci -all
> -rwxr-xr-x 1 root root 10815 Jan 20 17:04 /sbin/uci
> root at OpenWrt:~# uci --help
> uci: invalid option -- -
> Usage: uci [<options>] <command> [<arguments>]
>
> Commands:
> batch
> export [<config>]
> import [<config>]
> changes [<config>]
> commit [<config>]
> add <config> <section-type>
> add_list <config>.<section>.<option>=<string>
> show [<config>[.<section>[.<option>]]]
> get <config>.<section>[.<option>]
> set <config>.<section>[.<option>]=<value>
> delete <config>[.<section[.<option>]]
> rename <config>.<section>[.<option>]=<name>
> revert <config>[.<section>[.<option>]]
>
> Options:
> -c <path> set the search path for config files (default:
> /etc/config)
> -d <str> set the delimiter for list values in uci show
> -f <file> use <file> as input instead of stdin
> -m when importing, merge data into an existing package
> -n name unnamed sections on export (default)
> -N don't name unnamed sections
> -p <path> add a search path for config change files
> -P <path> add a search path for config change files and use
> as default
> -q quiet mode (don't print error messages)
> -s force strict mode (stop on parser errors, default)
> -S disable strict mode
> -X do not use extended syntax on 'show'
>
> root at OpenWrt:~# ls /etc/init.d/mmc_over_gpio -all
> -rwxr-xr-x 1 root root 1238 Feb 14 2009
> /etc/init.d/mmc_over_gpio
>
> root at OpenWrt:/# uci add fstab mount
> cfg064d78
> root at OpenWrt:/# uci set fstab. at mount[0].enabled=1
> root at OpenWrt:/# uci set fstab. at mount[0].fstype=ext3
> root at OpenWrt:/# uci set fstab. at mount[0].device=/dev/mmcblk0p1
> root at OpenWrt:/# uci set fstab. at mount[0].target=/mnt/mmc
> root at OpenWrt:/# uci set fstab. at mount[0].options=rw,sync,noatime
> root at OpenWrt:/# uci commit fstab
> root at OpenWrt:/# /etc/init.d/fstab restart
> umount: cannot umount /mnt/mmc: No such file or directory
> mount: mounting /dev/mmcblk0p1 on /mnt/mmc failed: No such file or
> directory
>
> root at OpenWrt:/# /etc/init.d/mmc_over_gpio
> Syntax: /etc/init.d/mmc_over_gpio [command]
>
> Available commands:
> start Start the service
> stop Stop the service
> restart Restart the service
> reload Reload configuration files (or restart if that fails)
> enable Enable service autostart
> disable Disable service autostart
>
> root at OpenWrt:/# /etc/init.d/mmc_over_gpio start
>
>
> Il 04/06/2016 04:40, Marco Castrovilli ha scritto:
>> hi andrew,
>> i've installed
>> openwrt-atheros-root.jffs2-64k
>> openwrt-atheros-vmlinux.lzma
>> from https://downloads.openwrt.org/kamikaze/8.09/atheros/
>>
>> after few problems to configure internet access, i did:
>>
>> opkg update
>> opkg install kmod-mmc-over-gpio kmod-fs-ext3 cfdisk e2fsprogs
>> kmod-nls-base kmod-nls-cp437 kmod-nls-iso8859-1
>>
>> and each installation was fine.
>>
>> during GPIO configuration i had the message:
>> uci: entry not found
>> after each command:
>> uci set mmc_over_gpio. at mmc_over_gpio[0].enabled=1
>> uci set mmc_over_gpio. at mmc_over_gpio[0].DI_pin=1
>> uci set mmc_over_gpio. at mmc_over_gpio[0].DO_pin=4
>> uci set mmc_over_gpio. at mmc_over_gpio[0].CLK_pin=3
>> uci set mmc_over_gpio. at mmc_over_gpio[0].CS_pin=7
>> then i had "can't create /config/gpiommc/ directory" error. so i
>> rebooted, but now i can ping fonera 15/16 times, 1 timeout, other
>> 10/12 ping ok,
>> then it is unreachable for some seconds and so looping on.
>>
>> do you know the reason?
>>
>> and now the final question: i soldered exactly like in figure above:
>> www.WiFi-Ita.com
>> as explained here:
>> http://www.wifi-ita.com/index.php?option=com_content&task=view&id=223
>>
>> must i have to solder ALL cables on pin of GPIO?
>>
>> thank you again.
>> Il 03/06/2016 16:32, Andrew Yong ha scritto:
>>> You'll want to use OpenWrt Kamikaze 8.09 and use the official package
>>> manager opkg. Follow the linked wiki page
>>> (https://wiki.openwrt.org/doc/howto/mmc_over_gpio) and you'll be fine.
>>>
>>> The latest releases have deprecated kmod-mmc-over-gpio in favor of
>>> just getting other generic $30 routers from AliExpress that have built
>>> in TF/MMC ports (generally RT5350), or AR9311 routers with USB e.g.
>>> TL-MR3020.
>>>
>>>
>>>
>>> On Fri, Jun 3, 2016 at 10:15 PM, Marco Castrovilli
>>> <marco.castrovilli at gmail.com> wrote:
>>>> thanks a lot for your immediate answer.
>>>> i followed this guide to mod fonera adding an sd card:
>>>> http://www.wifi-ita.com/index.php?option=com_content&task=view&id=223
>>>> and this one:
>>>> http://www.nabuk.org/f/index.php?topic=1486.0
>>>> everything is ok but i can't find 26215-4pinfon2100Driver7143.ipk
>>>> anywere.
>>>> i'm on kamikaze 7.09 and kernel:
>>>> Linux Legend 2.6.22.1 #5 Mon Aug 13 18:18:07 EDT 2007 mips unknown
>>>>
>>>> i tried to update (with ipkg, not opkg) but i have problem with
>>>> original
>>>> openwrt feed:
>>>> root at Legend:~# ipkg update
>>>> Downloading
>>>> http://downloads.openwrt.org/snapshots/atheros-2.6/packages/Packages
>>>> wget: server returned error: HTTP/1.1 404 Not Found
>>>> Downloading
>>>> http://downloads.openwrt.org/kamikaze/packages/mips/Packages
>>>> wget: server returned error: HTTP/1.1 404 Not Found
>>>> Downloading
>>>> http://downloads.x-wrt.org/xwrt/kamikaze/snapshots/atheros-2.6/packages/Packages
>>>>
>>>> wget: server returned error: HTTP/1.1 404 Not Found
>>>> An error ocurred, return value: 3.
>>>> Collected errors:
>>>> ipkg_download: ERROR: Command failed with return value 1: `wget
>>>> --passive-ftp -q -P /tmp/ipkg-hCDHje
>>>> http://downloads.openwrt.org/snapshots/atheros-2.6/packages/Packages'
>>>> ipkg_download: ERROR: Command failed with return value 1: `wget
>>>> --passive-ftp -q -P /tmp/ipkg-hCDHje
>>>> http://downloads.openwrt.org/kamikaze/packages/mips/Packages'
>>>> ipkg_download: ERROR: Command failed with return value 1: `wget
>>>> --passive-ftp -q -P /tmp/ipkg-hCDHje
>>>> http://downloads.x-wrt.org/xwrt/kamikaze/snapshots/atheros-2.6/packages/Packages'
>>>>
>>>> root at Legend:~#
>>>>
>>>> so i tried with other ones but:
>>>> root at Legend:~# ipkg update
>>>> Downloading
>>>> https://downloads.openwrt.org/kamikaze/7.09/atheros-2.6/packages/Packages
>>>>
>>>> wget: not an http or ftp url:
>>>> https://downloads.openwrt.org/kamikaze/7.09/atheros-2.6/packages/Packages
>>>>
>>>> Downloading
>>>> https://downloads.openwrt.org/kamikaze/7.09/atheros-2.6/packages/Packages
>>>>
>>>> wget: not an http or ftp url:
>>>> https://downloads.openwrt.org/kamikaze/7.09/atheros-2.6/packages/Packages
>>>>
>>>> Downloading
>>>> https://downloads.openwrt.org/kamikaze/7.09/atheros-2.6/packages/Packages
>>>>
>>>> wget: not an http or ftp url:
>>>> https://downloads.openwrt.org/kamikaze/7.09/atheros-2.6/packages/Packages
>>>>
>>>> An error ocurred, return value: 3.
>>>> Collected errors:
>>>> ipkg_download: ERROR: Command failed with return value 1: `wget
>>>> --passive-ftp -q -P /tmp/ipkg-nErUJo
>>>> https://downloads.openwrt.org/kamikaze/7.09/atheros-2.6/packages/Packages'
>>>>
>>>> ipkg_download: ERROR: Command failed with return value 1: `wget
>>>> --passive-ftp -q -P /tmp/ipkg-nErUJo
>>>> https://downloads.openwrt.org/kamikaze/7.09/atheros-2.6/packages/Packages'
>>>>
>>>> ipkg_download: ERROR: Command failed with return value 1: `wget
>>>> --passive-ftp -q -P /tmp/ipkg-nErUJo
>>>> https://downloads.openwrt.org/kamikaze/7.09/atheros-2.6/packages/Packages'
>>>>
>>>> root at Legend:~#
>>>>
>>>> i got a more recent wget (wget_1.10.2-2_mips.ipk) but stil have
>>>> problems
>>>> with ssl.
>>>> anyway, browsing manually feeds i can't find driver.
>>>>
>>>> perhaps i NEED to use kamikaze 8.09 and all troubles will run away?
>>>>
>>>> again many thanks Andrew for your interest: this is my last chance
>>>> to use a
>>>> microSD on my fonera 2100 :)
>>>>
>>>>
>>>>
>>>> Il 03/06/2016 15:49, Andrew Yong ha scritto:
>>>>
>>>> https://wiki.openwrt.org/doc/hardware/port.gpio and see relevant
>>>> sections
>>>> for bitbanging MMC over GPIO.
>>>>
>>>> On 3 Jun 2016 21:46, "Marco Castrovilli" <marco.castrovilli at gmail.com>
>>>> wrote:
>>>>> hi all!
>>>>> does anyone can help me to find mmc driver working on openwrt,
>>>>> installed
>>>>> on fonera 2100 (mips architectire)?
>>>>> thank you in advance.
>>>>>
>>>>> _______________________________________________
>>>>> Lede-dev mailing list
>>>>> Lede-dev at lists.infradead.org
>>>>> http://lists.infradead.org/mailman/listinfo/lede-dev
>>>>
>
More information about the Lede-dev
mailing list