[LEDE-DEV] [PATCHv3 1/1] [brcm63xx] Add initial support for EVG2000
Graham Fairweather
xotic750 at gmail.com
Fri Jun 3 03:45:16 PDT 2016
Hi and thanks.
On 3 June 2016 at 12:07, Álvaro Fernández Rojas <noltari at gmail.com> wrote:
> Hello Graham,
>
> Pulled into my staging tree with some changes (whitespace fixes, cleanups...):
> https://git.lede-project.org/?p=lede/noltari/staging.git;a=shortlog;h=refs/heads/brcm63xx-next
>
> Regards,
> Álvaro.
>
> El 23/5/16 a las 0:56, Xotic750 escribió:
>> From: Graham Fairweather <xotic750 at gmail.com>
>>
>> This patch adds support for the Netgear EVG2000 VoIP Gateway to the
>> bcm63xx targets.
>> Ran 'make target/linux/refresh V=s' after update to kernel 4.4.10 from
>> 4.4.8 where the initial patch was added.
>> This device was not sold to the general public, but rather is/was
>> provided by telcos to customers in Sweden, Australia, Singapore and
>> other parts of asia.
>> System-On-Chip: Broadcom BCM6369 (2 * BMIPS4350 v3.1 / 400 MHz)
>> Flash size: 16 MiB
>> RAM size: 64 MiB
>> Wireless: BCM4322 802.11b/g/n (onboard)
>> Ethernet: Broadcom BCM53115
>> USB: 2 x USB 2.0
>> Known issues:
>> - Unable to detect 53115 switch. This appear to be a problem with
>> probing for the PHY using MDIO and results in error 5. Doesn't seem to
>> be a problem with the configuration, and could use someone with
>> experience to have a look at it.
>> - Uses the b43 driver as using the OpenWRT/LEDE broadcom-wl driver
>> fails to load the firmware for the 4322, so 802.11n is not supported.
>> The factory build uses a newer broadcom-wl driver.
>> - No support for the 2 VoIP ports (not attempted)
>> More info on the device and the research can be found at:
>> https://wiki.openwrt.org/toh/netgear/evg2000
>> https://wikidevi.com/wiki/Netgear_EVG2000
>> https://github.com/Xotic750/mirror-lede/tree/evg2000
>> https://forum.openwrt.org/viewtopic.php?id=63950
>> Signed-off-by: Graham Fairweather <xotic750 at gmail.com>
>> ---
>> .../linux/brcm63xx/base-files/etc/board.d/01_leds | 7 ++
>> .../brcm63xx/base-files/etc/board.d/02_network | 1 +
>> target/linux/brcm63xx/base-files/etc/diag.sh | 3 +
>> .../base-files/etc/uci-defaults/09_fix_crc | 2 +-
>> target/linux/brcm63xx/base-files/lib/brcm63xx.sh | 3 +
>> .../lib/preinit/05_init_interfaces_brcm63xx | 1 +
>> target/linux/brcm63xx/dts/evg2000.dts | 103 +++++++++++++++++++++
>> target/linux/brcm63xx/image/Makefile | 2 +
>> .../brcm63xx/patches-4.1/575-board_EVG2000.patch | 62 +++++++++++++
>> ...-m25p80-use-parsers-if-provided-in-flash-.patch | 2 +-
>> ...CES-m25p80-add-support-for-limiting-reads.patch | 4 +-
>> .../414-MTD-m25p80-allow-passing-pp_data.patch | 2 +-
>> .../brcm63xx/patches-4.4/575-board_EVG2000.patch | 62 +++++++++++++
>> target/linux/brcm63xx/profiles/netgear.mk | 10 ++
>> 14 files changed, 259 insertions(+), 5 deletions(-)
>> create mode 100644 target/linux/brcm63xx/dts/evg2000.dts
>> create mode 100644 target/linux/brcm63xx/patches-4.1/575-board_EVG2000.patch
>> create mode 100644 target/linux/brcm63xx/patches-4.4/575-board_EVG2000.patch
>>
>> diff --git a/target/linux/brcm63xx/base-files/etc/board.d/01_leds b/target/linux/brcm63xx/base-files/etc/board.d/01_leds
>> index 8339254..4163214 100755
>> --- a/target/linux/brcm63xx/base-files/etc/board.d/01_leds
>> +++ b/target/linux/brcm63xx/base-files/etc/board.d/01_leds
>> @@ -24,6 +24,13 @@ dgnd3700v1_dgnd3800b)
>> ucidef_set_led_usbdev "usb1" "USB1" "DGND3700v1_3800B:green:usb-back" "1-1"
>> ucidef_set_led_usbdev "usb2" "USB2" "DGND3700v1_3800B:green:usb-front" "1-2"
>> ;;
>> +evg2000)
>> + ucidef_set_led_netdev "lan" "LAN" "EVG2000:green:lan" "eth0"
>> + ucidef_set_led_netdev "wan" "WAN" "EVG2000:green:wan" "eth1"
>> + ucidef_set_led_netdev "wlan0" "WIFI" "EVG2000:green:wireless" "wlan0"
>> + ucidef_set_led_usbdev "usb1" "USB1" "EVG2000:green:voip1" "1-1"
>> + ucidef_set_led_usbdev "usb2" "USB2" "EVG2000:green:voip2" "1-2"
>> + ;;
>> fast2704n)
>> ucidef_set_led_netdev "wan" "WAN" "F at ST2704N:green:inet" "eth0.2"
>> ;;
>> diff --git a/target/linux/brcm63xx/base-files/etc/board.d/02_network b/target/linux/brcm63xx/base-files/etc/board.d/02_network
>> index f96da08..83367c1 100755
>> --- a/target/linux/brcm63xx/base-files/etc/board.d/02_network
>> +++ b/target/linux/brcm63xx/base-files/etc/board.d/02_network
>> @@ -11,6 +11,7 @@ board_config_update
>> case "$(brcm63xx_board_name)" in
>>
>> cvg834g |\
>> +evg2000 |\
>> rta770bw |\
>> rta770w |\
>> spw303v |\
>> diff --git a/target/linux/brcm63xx/base-files/etc/diag.sh b/target/linux/brcm63xx/base-files/etc/diag.sh
>> index b864964..6ac2459 100644
>> --- a/target/linux/brcm63xx/base-files/etc/diag.sh
>> +++ b/target/linux/brcm63xx/base-files/etc/diag.sh
>> @@ -70,6 +70,9 @@ set_state() {
>> dgnd3700v1_dgnd3800b)
>> status_led="DGND3700v1_3800B:green:power"
>> ;;
>> + evg2000)
>> + status_led="EVG2000:green:power"
>> + ;;
>> fast2504n)
>> status_led="fast2504n:green:ok"
>> ;;
>> diff --git a/target/linux/brcm63xx/base-files/etc/uci-defaults/09_fix_crc b/target/linux/brcm63xx/base-files/etc/uci-defaults/09_fix_crc
>> index 70dbe2a..1201168 100644
>> --- a/target/linux/brcm63xx/base-files/etc/uci-defaults/09_fix_crc
>> +++ b/target/linux/brcm63xx/base-files/etc/uci-defaults/09_fix_crc
>> @@ -21,6 +21,7 @@ case "$(brcm63xx_board_name)" in
>> cpva642 |\
>> ct-6373 |\
>> dsl-274xb-f |\
>> + evg2000 |\
>> hg622 |\
>> magic |\
>> p870hw-51a_v2 |\
>> @@ -37,4 +38,3 @@ case "$(brcm63xx_board_name)" in
>> do_fixcrc
>> ;;
>> esac
>> -
>> diff --git a/target/linux/brcm63xx/base-files/lib/brcm63xx.sh b/target/linux/brcm63xx/base-files/lib/brcm63xx.sh
>> index a2d6519..9cc0b2b 100755
>> --- a/target/linux/brcm63xx/base-files/lib/brcm63xx.sh
>> +++ b/target/linux/brcm63xx/base-files/lib/brcm63xx.sh
>> @@ -183,6 +183,9 @@ brcm63xx_dt_detect() {
>> "Netgear DGND3700v1/DGND3800B")
>> board_name="dgnd3700v1_dgnd3800b"
>> ;;
>> + "Netgear EVG2000")
>> + board_name="evg2000"
>> + ;;
>> "NuCom R5010UN v2")
>> board_name="r5010un_v2"
>> ;;
>> diff --git a/target/linux/brcm63xx/base-files/lib/preinit/05_init_interfaces_brcm63xx b/target/linux/brcm63xx/base-files/lib/preinit/05_init_interfaces_brcm63xx
>> index 7e4dfcb..1e3fc14 100644
>> --- a/target/linux/brcm63xx/base-files/lib/preinit/05_init_interfaces_brcm63xx
>> +++ b/target/linux/brcm63xx/base-files/lib/preinit/05_init_interfaces_brcm63xx
>> @@ -18,6 +18,7 @@ set_preinit_iface() {
>> dsl-274xb-c |\
>> dsl-274xb-f |\
>> dsl-275xb-d |\
>> + evg2000 |\
>> fast2504n |\
>> fast2704v2 |\
>> hg553 |\
>> diff --git a/target/linux/brcm63xx/dts/evg2000.dts b/target/linux/brcm63xx/dts/evg2000.dts
>> new file mode 100644
>> index 0000000..04f7b84
>> --- /dev/null
>> +++ b/target/linux/brcm63xx/dts/evg2000.dts
>> @@ -0,0 +1,103 @@
>> +/dts-v1/;
>> +
>> +#include "bcm6368.dtsi"
>> +
>> +#include <dt-bindings/input/input.h>
>> +
>> +/ {
>> + model = "Netgear EVG2000";
>> + compatible = "netgear,evg2000", "brcm,bcm6368";
>> +
>> + gpio-keys-polled {
>> + compatible = "gpio-keys-polled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + poll-interval = <20>;
>> + debounce-interval = <60>;
>> +
>> + reset {
>> + label = "reset";
>> + gpios = <&gpio0 25 1>;
>> + linux,code = <KEY_RESTART>;
>> + };
>> + wps {
>> + label = "wps";
>> + gpios = <&gpio0 26 1>;
>> + linux,code = <KEY_WPS_BUTTON>;
>> + };
>> + };
>> +
>> + gpio-leds {
>> + compatible = "gpio-leds";
>> +
>> + voip1_green {
>> + label = "EVG2000:green:voip1";
>> + gpios = <&gpio0 14 1>;
>> + };
>> + voip2_green {
>> + label = "EVG2000:green:voip2";
>> + gpios = <&gpio0 2 1>;
>> + };
>> + inet_red {
>> + label = "EVG2000:red:inet";
>> + gpios = <&gpio0 4 1>;
>> + };
>> + inet_green {
>> + label = "EVG2000:green:inet";
>> + gpios = <&gpio0 5 1>;
>> + };
>> + usb_green {
>> + label = "EVG2000:green:usb";
>> + gpios = <&gpio0 15 1>;
>> + };
>> + power_green {
>> + label = "EVG2000:green:power";
>> + gpios = <&gpio0 22 1>;
>> + default-state = "on";
>> + };
>> + power_red {
>> + label = "EVG2000:red:power";
>> + gpios = <&gpio0 23 1>;
>> + };
>> + lan_green {
>> + label = "EVG2000:green:lan";
>> + gpios = <&gpio0 24 1>;
>> + };
>> + wireless_green {
>> + label = "EVG2000:green:wireless";
>> + gpios = <&gpio0 26 1>;
>> + };
>> + wan_green {
>> + label = "EVG2000:green:wan";
>> + gpios = <&gpio0 27 1>;
>> + };
>> + };
>> +};
>> +
>> +&pflash {
>> + status = "ok";
>> +
>> + linux,part-probe = "bcm63xxpart";
>> +
>> + cfe at 0 {
>> + label = "CFE";
>> + reg = <0x00000000 0x00020000>;
>> + read-only;
>> + };
>> +
>> + linux at 20000 {
>> + label = "linux";
>> + reg = <0x00020000 0x00f40000>;
>> + };
>> +
>> + board_data at f60000 {
>> + label = "board_data";
>> + reg = <0x00f60000 0x00080000>;
>> + read-only;
>> + };
>> +
>> + nvram at fe0000 {
>> + label = "nvram";
>> + reg = <0x00fe0000 0x00020000>;
>> + };
>> +};
>> diff --git a/target/linux/brcm63xx/image/Makefile b/target/linux/brcm63xx/image/Makefile
>> index e00b6fb..f1fb86b 100644
>> --- a/target/linux/brcm63xx/image/Makefile
>> +++ b/target/linux/brcm63xx/image/Makefile
>> @@ -593,6 +593,8 @@ $(eval $(call bcm63xxCfeRamdisk,DG834GV4,DG834GTv4,dg834g_v4,96348W3,6348))
>> $(eval $(call bcm63xxCfeNetgear,DGND3700v1_3800B,DGND3700v1,dgnd3700v1,96368MVWG,6368,--image-offset 0x20000 --block-size 0x20000,U12L144T01_NETGEAR_NEWLED,1))
>> # Netgear DGND3800B
>> $(eval $(call bcm63xxCfeNetgear,DGND3700v1_3800B,DGND3800B,dgnd3700v1,96368MVWG,6368,--image-offset 0x20000 --block-size 0x20000,U12L144T11_NETGEAR_NEWLED,1))
>> +# Netgear EVG2000
>> +$(eval $(call bcm63xxCfeNetgear,EVG2000,EVG2000,evg2000,96369PVG,6369,--image-offset 0x20000 --block-size 0x20000,U12H154T90_NETGEAR,1))
>> # NuCom R5010UNv2
>> $(eval $(call bcm63xxCfe,R5010UNV2,R5010UNv2,r5010unv2,96328ang,6328,--pad 8))
>> # Pirelli Alice Gate VoIP 2 Plus Wi-Fi AGPF-S0
>> diff --git a/target/linux/brcm63xx/patches-4.1/575-board_EVG2000.patch b/target/linux/brcm63xx/patches-4.1/575-board_EVG2000.patch
>> new file mode 100644
>> index 0000000..9339085
>> --- /dev/null
>> +++ b/target/linux/brcm63xx/patches-4.1/575-board_EVG2000.patch
>> @@ -0,0 +1,62 @@
>> +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
>> ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
>> +@@ -2010,6 +2010,43 @@ static struct board_info __initdata boar
>> + .num_spis = ARRAY_SIZE(DGND3700v1_3800B_spi_devices),
>> + };
>> +
>> ++static struct sprom_fixup __initdata EVG2000_fixups[] = {
>> ++ { .offset = 219, .value = 0xec08 },
>> ++};
>> ++
>> ++static struct board_info __initdata board_EVG2000 = {
>> ++ .name = "96369PVG",
>> ++ .expected_cpu_id = 0x6368,
>> ++
>> ++ .has_uart0 = 1,
>> ++ .has_pci = 1,
>> ++ .has_ohci0 = 1,
>> ++ .has_ehci0 = 1,
>> ++ .num_usbh_ports = 2,
>> ++
>> ++ .has_enetsw = 1,
>> ++ .enetsw = {
>> ++ .used_ports = {
>> ++ [5] = {
>> ++ .used = 1,
>> ++ .phy_id = 0xff,
>> ++ .bypass_link = 1,
>> ++ .force_speed = 1000,
>> ++ .force_duplex_full = 1,
>> ++ .name = "RGMII",
>> ++ },
>> ++ },
>> ++ },
>> ++ .use_fallback_sprom = 1,
>> ++ .fallback_sprom = {
>> ++ .type = SPROM_BCM4322,
>> ++ .pci_bus = 0,
>> ++ .pci_dev = 1,
>> ++ .board_fixups = EVG2000_fixups,
>> ++ .num_board_fixups = ARRAY_SIZE(EVG2000_fixups),
>> ++ },
>> ++};
>> ++
>> + static struct board_info __initdata board_HG655b = {
>> + .name = "HW65x",
>> + .expected_cpu_id = 0x6368,
>> +@@ -2610,6 +2647,7 @@ static const struct board_info __initcon
>> + &board_96368mvwg,
>> + &board_96368mvngr,
>> + &board_DGND3700v1_3800B,
>> ++ &board_EVG2000,
>> + &board_HG622,
>> + &board_HG655b,
>> + &board_P870HW51A_V2,
>> +@@ -2722,6 +2760,7 @@ static struct of_device_id const bcm963x
>> + { .compatible = "huawei,hg622", .data = &board_HG622, },
>> + { .compatible = "huawei,hg655b", .data = &board_HG655b, },
>> + { .compatible = "netgear,dgnd3700v1", .data = &board_DGND3700v1_3800B, },
>> ++ { .compatible = "netgear,evg2000", .data = &board_EVG2000, },
>> + { .compatible = "zyxel,p870hw-51a-v2", .data = &board_P870HW51A_V2, },
>> + #endif
>> + #ifdef CONFIG_BCM63XX_CPU_63268
>> diff --git a/target/linux/brcm63xx/patches-4.4/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch b/target/linux/brcm63xx/patches-4.4/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch
>> index be62e67..4793836 100644
>> --- a/target/linux/brcm63xx/patches-4.4/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch
>> +++ b/target/linux/brcm63xx/patches-4.4/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch
>> @@ -11,7 +11,7 @@ Signed-off-by: Jonas Gorski <jonas.gorski at gmail.com>
>>
>> --- a/drivers/mtd/devices/m25p80.c
>> +++ b/drivers/mtd/devices/m25p80.c
>> -@@ -229,7 +229,8 @@ static int m25p_probe(struct spi_device
>> +@@ -251,7 +251,8 @@ static int m25p_probe(struct spi_device
>>
>> ppdata.of_node = spi->dev.of_node;
>>
>> diff --git a/target/linux/brcm63xx/patches-4.4/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch b/target/linux/brcm63xx/patches-4.4/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch
>> index 3877442..75a874d 100644
>> --- a/target/linux/brcm63xx/patches-4.4/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch
>> +++ b/target/linux/brcm63xx/patches-4.4/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch
>> @@ -28,7 +28,7 @@ Signed-off-by: Jonas Gorski <jonas.gorski at gmail.com>
>> size_t *retlen, u_char *buf)
>> {
>> struct m25p *flash = nor->priv;
>> -@@ -152,6 +153,29 @@ static int m25p80_read(struct spi_nor *n
>> +@@ -174,6 +175,29 @@ static int m25p80_read(struct spi_nor *n
>> return 0;
>> }
>>
>> @@ -58,7 +58,7 @@ Signed-off-by: Jonas Gorski <jonas.gorski at gmail.com>
>> static int m25p80_erase(struct spi_nor *nor, loff_t offset)
>> {
>> struct m25p *flash = nor->priv;
>> -@@ -223,6 +247,9 @@ static int m25p_probe(struct spi_device
>> +@@ -245,6 +269,9 @@ static int m25p_probe(struct spi_device
>> else
>> flash_name = spi->modalias;
>>
>> diff --git a/target/linux/brcm63xx/patches-4.4/414-MTD-m25p80-allow-passing-pp_data.patch b/target/linux/brcm63xx/patches-4.4/414-MTD-m25p80-allow-passing-pp_data.patch
>> index e421e9a..bbb565e 100644
>> --- a/target/linux/brcm63xx/patches-4.4/414-MTD-m25p80-allow-passing-pp_data.patch
>> +++ b/target/linux/brcm63xx/patches-4.4/414-MTD-m25p80-allow-passing-pp_data.patch
>> @@ -10,7 +10,7 @@ Subject: [PATCH 64/79] MTD: m25p80: allow passing pp_data
>>
>> --- a/drivers/mtd/devices/m25p80.c
>> +++ b/drivers/mtd/devices/m25p80.c
>> -@@ -250,6 +250,9 @@ static int m25p_probe(struct spi_device
>> +@@ -272,6 +272,9 @@ static int m25p_probe(struct spi_device
>> if (data)
>> flash->max_transfer_len = data->max_transfer_len;
>>
>> diff --git a/target/linux/brcm63xx/patches-4.4/575-board_EVG2000.patch b/target/linux/brcm63xx/patches-4.4/575-board_EVG2000.patch
>> new file mode 100644
>> index 0000000..fc7afc7
>> --- /dev/null
>> +++ b/target/linux/brcm63xx/patches-4.4/575-board_EVG2000.patch
>> @@ -0,0 +1,62 @@
>> +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
>> ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
>> +@@ -2011,6 +2011,43 @@ static struct board_info __initdata boar
>> + .num_spis = ARRAY_SIZE(DGND3700v1_3800B_spi_devices),
>> + };
>> +
>> ++static struct sprom_fixup __initdata EVG2000_fixups[] = {
>> ++ { .offset = 219, .value = 0xec08 },
>> ++};
>> ++
>> ++static struct board_info __initdata board_EVG2000 = {
>> ++ .name = "96369PVG",
>> ++ .expected_cpu_id = 0x6368,
>> ++
>> ++ .has_uart0 = 1,
>> ++ .has_pci = 1,
>> ++ .has_ohci0 = 1,
>> ++ .has_ehci0 = 1,
>> ++ .num_usbh_ports = 2,
>> ++
>> ++ .has_enetsw = 1,
>> ++ .enetsw = {
>> ++ .used_ports = {
>> ++ [5] = {
>> ++ .used = 1,
>> ++ .phy_id = 0xff,
>> ++ .bypass_link = 1,
>> ++ .force_speed = 1000,
>> ++ .force_duplex_full = 1,
>> ++ .name = "RGMII",
>> ++ },
>> ++ },
>> ++ },
>> ++ .use_fallback_sprom = 1,
>> ++ .fallback_sprom = {
>> ++ .type = SPROM_BCM4322,
>> ++ .pci_bus = 0,
>> ++ .pci_dev = 1,
>> ++ .board_fixups = EVG2000_fixups,
>> ++ .num_board_fixups = ARRAY_SIZE(EVG2000_fixups),
>> ++ },
>> ++};
>> ++
>> + static struct board_info __initdata board_HG655b = {
>> + .name = "HW65x",
>> + .expected_cpu_id = 0x6368,
>> +@@ -2611,6 +2648,7 @@ static const struct board_info __initcon
>> + &board_96368mvwg,
>> + &board_96368mvngr,
>> + &board_DGND3700v1_3800B,
>> ++ &board_EVG2000,
>> + &board_HG622,
>> + &board_HG655b,
>> + &board_P870HW51A_V2,
>> +@@ -2723,6 +2761,7 @@ static struct of_device_id const bcm963x
>> + { .compatible = "huawei,hg622", .data = &board_HG622, },
>> + { .compatible = "huawei,hg655b", .data = &board_HG655b, },
>> + { .compatible = "netgear,dgnd3700v1", .data = &board_DGND3700v1_3800B, },
>> ++ { .compatible = "netgear,evg2000", .data = &board_EVG2000, },
>> + { .compatible = "zyxel,p870hw-51a-v2", .data = &board_P870HW51A_V2, },
>> + #endif
>> + #ifdef CONFIG_BCM63XX_CPU_63268
>> diff --git a/target/linux/brcm63xx/profiles/netgear.mk b/target/linux/brcm63xx/profiles/netgear.mk
>> index bc345bb..e3bc34a 100644
>> --- a/target/linux/brcm63xx/profiles/netgear.mk
>> +++ b/target/linux/brcm63xx/profiles/netgear.mk
>> @@ -41,3 +41,13 @@ define Profile/DGND3700v1_3800B/Description
>> Package set optimized for DGND3700 v1 / DGND3800B.
>> endef
>> $(eval $(call Profile,DGND3700v1_3800B))
>> +
>> +define Profile/EVG2000
>> + NAME:=Netgear EVG2000
>> + PACKAGES:=kmod-b43 wpad-mini \
>> + kmod-usb2 kmod-usb-ohci kmod-ledtrig-usbdev
>> +endef
>> +define Profile/EVG2000/Description
>> + Package set optimized for EVG2000.
>> +endef
>> +$(eval $(call Profile,EVG2000))
>
More information about the Lede-dev
mailing list