[openwrt/openwrt] realtek: mdio: rtl838x: activate combo PHY media detection

[LEDE Commits]

robimarko pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/17f12695d0838681020e598ce231af87057f955f

commit 17f12695d0838681020e598ce231af87057f955f
Author: Markus Stockhausen <markus.stockhausen at gmx.de>
AuthorDate: Fri Jan 23 13:36:06 2026 +0100

    realtek: mdio: rtl838x: activate combo PHY media detection
    
    There is a misunderstanding about BIT(7) aka EX_PHY_MAN_24_27 in
    SMI_GLB_CTRL register. The SDK sets/clears it at different places and
    it is not clear what it is for. Observation shows that it is essential
    for a working MAC_LINK_MEDIA_STS register.
    
    A RTL838x device has usally two configurations
    
    - port 24/26 are 2 serdes driven fiber ports
    - port 24-27 are 4 PHY driven combo ports
    
    In the combo case the above bit must be set so that a switch between
    copper and fiber can be detected. Cleanup the MDIO initialization
    and remove the unneeded bit handling in the DSA driver.
    
    Signed-off-by: Markus Stockhausen <markus.stockhausen at gmx.de>
    Link: https://github.com/openwrt/openwrt/pull/21653
    Signed-off-by: Robert Marko <robimarko at gmail.com>
---
 .../files-6.12/drivers/net/dsa/rtl83xx/common.c       |  4 ++--
 .../files-6.12/drivers/net/mdio/mdio-realtek-otto.c   | 19 +++++++++++++------
 2 files changed, 15 insertions(+), 8 deletions(-)

diff --git a/target/linux/realtek/files-6.12/drivers/net/dsa/rtl83xx/common.c b/target/linux/realtek/files-6.12/drivers/net/dsa/rtl83xx/common.c
index 373ab3728d..7c1ab5e054 100644
--- a/target/linux/realtek/files-6.12/drivers/net/dsa/rtl83xx/common.c
+++ b/target/linux/realtek/files-6.12/drivers/net/dsa/rtl83xx/common.c
@@ -368,8 +368,8 @@ static int rtl83xx_mdio_probe(struct rtl838x_switch_priv *priv)
 
 	/* Enable PHY control via SoC */
 	if (priv->family_id == RTL8380_FAMILY_ID) {
-		/* Enable SerDes NWAY and PHY control via SoC */
-		sw_w32_mask(BIT(7), BIT(15), RTL838X_SMI_GLB_CTRL);
+		/* Enable PHY control by telling SoC that "PHY patching is done" */
+		sw_w32_mask(0, BIT(15), RTL838X_SMI_GLB_CTRL);
 	} else if (priv->family_id == RTL8390_FAMILY_ID) {
 		/* Disable PHY polling via SoC */
 		sw_w32_mask(BIT(7), 0, RTL839X_SMI_GLB_CTRL);
diff --git a/target/linux/realtek/files-6.12/drivers/net/mdio/mdio-realtek-otto.c b/target/linux/realtek/files-6.12/drivers/net/mdio/mdio-realtek-otto.c
index 44216fe2d9..896a08652c 100644
--- a/target/linux/realtek/files-6.12/drivers/net/mdio/mdio-realtek-otto.c
+++ b/target/linux/realtek/files-6.12/drivers/net/mdio/mdio-realtek-otto.c
@@ -841,14 +841,21 @@ static void rtmdio_get_phy_info(struct mii_bus *bus, int addr, struct rtmdio_phy
 
 static int rtmdio_838x_reset(struct mii_bus *bus)
 {
-	pr_debug("%s called\n", __func__);
-	/* Disable MAC polling the PHY so that we can start configuration */
-	sw_w32(0x00000000, RTMDIO_838X_SMI_POLL_CTRL);
+	struct rtmdio_bus_priv *priv = bus->priv;
+	int combo_phy;
 
-	/* Enable PHY control via SoC */
-	sw_w32_mask(0, 1 << 15, RTMDIO_838X_SMI_GLB_CTRL);
+	/* Disable MAC polling for PHY config. It will be activated later in the DSA driver */
+	sw_w32(0, RTMDIO_838X_SMI_POLL_CTRL);
+
+	/*
+	 * Control bits EX_PHY_MAN_xxx have an important effect on the detection of the media
+	 * status (fibre/copper) of a PHY. Once activated, register MAC_LINK_MEDIA_STS can
+	 * give the real media status (0=copper, 1=fibre). For now assume that if port 24 is
+	 * PHY driven, it must be a combo PHY and media detection is needed.
+	 */
+	combo_phy = priv->smi_bus[24] < 0 ? 0 : BIT(7);
+	sw_w32_mask(BIT(7), combo_phy, RTMDIO_838X_SMI_GLB_CTRL);
 
-	/* Probably should reset all PHYs here... */
 	return 0;
 }